Search NASA⌕ Search

SEARCH · Search NASA

Results for “Describing function”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,225 records · Page 68
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

A physical model for predicting bidirectional reflectances over bare soil

While most previous attempts to retrieve soil surface optical property characteristics have proceeded through a fitting of empirical functions to the data, an optimization technique is presently applied to a physically-based surface reflectance model developed for the study of planetary surfaces. This inversion procedure is shown to allow the direct estimation of the single-scattering coefficient, two parameters describing the 'hot spot' phenomenon, and two parameters describing the scattering phase function. A comparison of inversion technique results with both synthetic data and actual observations shows the model to be capable of predicting the observed bidirectional reflectances as well as directional-hemispherical reflectances; it can also build the complete radiance field over the upward hemisphere.

Pinty, Bernard↗
NASA NTRS1998

Three-dimensional organization of otolith-ocular reflexes in rhesus monkeys. III. Responses To translation

The three-dimensional (3-D) properties of the translational vestibulo-ocular reflexes (translational VORs) during lateral and fore-aft oscillations in complete darkness were studied in rhesus monkeys at frequencies between 0.16 and 25 Hz. In addition, constant velocity off-vertical axis rotations extended the frequency range to 0.02 Hz. During lateral motion, horizontal responses were in phase with linear velocity in the frequency range of 2-10 Hz. At both lower and higher frequencies, phase lags were introduced. Torsional response phase changed more than 180 degrees in the tested frequency range such that torsional eye movements, which could be regarded as compensatory to "an apparent roll tilt" at the lowest frequencies, became anticompensatory at all frequencies above approximately 1 Hz. These results suggest two functionally different frequency bandwidths for the translational VORs. In the low-frequency spectrum (<<0.5 Hz), horizontal responses compensatory to translation are small and high-pass-filtered whereas torsional response sensitivity is relatively frequency independent. At higher frequencies however, both horizontal and torsional response sensitivity and phase exhibit a similar frequency dependence, suggesting a common role during head translation. During up-down motion, vertical responses were in phase with translational velocity at 3-5 Hz but phase leads progressively increased for lower frequencies (>90 degrees at frequencies <0.2 Hz). No consistent dependence on static head orientation was observed for the vertical response components during up-down motion and the horizontal and torsional response components during lateral translation. The frequency response characteristics of the translational VORs were fitted by "periphery/brain stem" functions that related the linear acceleration input, transduced by primary otolith afferents, to the velocity signals providing the input to the velocity-to-position neural integrator and the oculomotor plant. The lowest-order, best-fit periphery/brain stem model that approximated the frequency dependence of the data consisted of a second order transfer function with two alternating poles (at 0.4 and 7.2 Hz) and zeros (at 0.035 and 3.4 Hz). In addition to clearly differentiator dynamics at low frequencies (less than approximately 0.5 Hz), there was no frequency bandwidth where the periphery/brain stem function could be approximated by an integrator, as previously suggested. In this scheme, the oculomotor plant dynamics are assumed to perform the necessary high-frequency integration as required by the reflex. The detailed frequency dependence of the data could only be precisely described by higher order functions with nonminimum phase characteristics that preclude simple filtering of afferent inputs and might be suggestive of distributed spatiotemporal processing of otolith signals in the translational VORs.

Non-NASA Center↗
NASA NTRS2004

An Analytical Calibration Approach for the Polarimetric Airborne C Band Radiometer

Passive microwave remote sensing is sensitive to the quantity and distribution of water in soil and vegetation. During summer 2000, the Microwave Geophysics Group at the University of Michigan conducted the 7th Radiobrightness Energy Balance Experiment (REBEX-7) over a corn canopy in Michigan. Long time series of brightness temperatures, soil moisture and micrometeorology on the plot scale were taken. This paper addresses the calibration of the NASA GSFC polarimetric airborne C band microwave radiometer (ACMR) that participated in REBEX-7. Passive polarimeters are typically calibrated using an end-to-end approach based upon a standard artificial target or a well-known geophysical target. Analyzing the major internal functional subsystems offers a different perspective. The primary goal of this approach is to provide a transfer function that not only describes the system in its entirety but also accounts for the contributions of each subsystem toward the final modified Stokes parameters. This approach also serves as a realistic instrument simulator, a useful tool for future designs. The ACMR architecture can be partitioned into several functional subsystems. Each subsystem was extensively measured and the estimated parameters were imported into the overall system model. We will present the results of polarimetric antenna measurements, the instrument model as well as four Stokes observations from REBEX-7 using a first order inversion.

Pham, Hanh↗
NASA NTRS1975

Information content in Iris spectra

Spectra from the satellite instrument Iris (infrared interferometer spectrometer) were examined to find the number of independent variables needed to describe the broad-band high-resolution spectral data. The radiated power in the atmospheric window from 771 to 981 per cm was the first parameter chosen for fitting observed spectra. At succeeding levels of analysis, the residual variability (observed spectrum minus best-fit spectrum) in an ensemble of observations was partitioned into spectral eigenvectors. The eigenvector describing the largest fraction of this variability was examined for a strong spectral signature; the power in the corresponding spectral band was then used as the next fitting parameter. The measured power in nine spectral intervals, when it was inserted in the spectral-fitting functions, was adequate to describe most spectra to within the noise level of Iris. Considerations of relative signal strength and scales of atmospheric variability suggest a combination sounder (multichannel, broad field of view) scanner (window channel, small field of view) as an efficient observing instrument.

Price, J. C.↗
NASA NTRS2002

Who or What? Self-Replication and Function-Reproduction in the Origin of Life

In this presentation, we will present results on the fundamental properties of two classes of replicating systems: autocatalytic replicators that reproduce exact copies of a template molecule, and function reproducers that maintain a set of essential functions without replicating the identities of the functional moieties. We will describe the stability and behavior in-the-large of autocatalytic replicators. Most importantly, we have found no sharp distinction between an autocatalytic and a non-autocatalytic domain. We will also present a new derivation of von Kiedrowski's square-root rate law. Function - reproducers are proposed as an important component of protocells and we will present theoretical results on a simple model system that incorporates known peptide biophysics. For a wide range of parameters, we have shown that this type of system can improve its overall performance, even in the absence of any method for information storage. This type of system improvement is defined to be non-genomic evolution.

New, Michael H.↗
NASA NTRS2008

Space Telecommunications Radio Systems (STRS) Hardware Architecture Standard: Release 1.0 Hardware Section

This report defines a hardware architecture approach for software-defined radios to enable commonality among NASA space missions. The architecture accommodates a range of reconfigurable processing technologies including general-purpose processors, digital signal processors, field programmable gate arrays, and application-specific integrated circuits (ASICs) in addition to flexible and tunable radiofrequency front ends to satisfy varying mission requirements. The hardware architecture consists of modules, radio functions, and interfaces. The modules are a logical division of common radio functions that compose a typical communication radio. This report describes the architecture details, the module definitions, the typical functions on each module, and the module interfaces. Tradeoffs between component-based, custom architecture and a functional-based, open architecture are described. The architecture does not specify a physical implementation internally on each module, nor does the architecture mandate the standards or ratings of the hardware used to construct the radios.

Reinhart, Richard C.↗
NASA NTRS2008

Hardware Architecture Study for NASA's Space Software Defined Radios

This study defines a hardware architecture approach for software defined radios to enable commonality among NASA space missions. The architecture accommodates a range of reconfigurable processing technologies including general purpose processors, digital signal processors, field programmable gate arrays (FPGAs), and application-specific integrated circuits (ASICs) in addition to flexible and tunable radio frequency (RF) front-ends to satisfy varying mission requirements. The hardware architecture consists of modules, radio functions, and and interfaces. The modules are a logical division of common radio functions that comprise a typical communication radio. This paper describes the architecture details, module definitions, and the typical functions on each module as well as the module interfaces. Trade-offs between component-based, custom architecture and a functional-based, open architecture are described. The architecture does not specify the internal physical implementation within each module, nor does the architecture mandate the standards or ratings of the hardware used to construct the radios.

Reinhart, Richard C.↗
DOE OSTI2020

Holomorphic waves of black hole microstructure

We obtain the largest families constructed to date of $$ \frac{1}{8} $$ 1 8 -BPS solutions of type IIB supergravity. They have the same charges and mass as supersymmetric D1-D5-P black holes, but they cap off smoothly with no horizon. Their construction relies on the structure of superstratum states, but allows the momentum wave to have an arbitrary shape. Each family is based on an arbitrary holomorphic function of one variable. More broadly, we show that the most general solution is described by two arbitrary holomorphic functions of three variables. After exhibiting several new families of such “holomorphic superstrata,” we reformulate the BPS backgrounds and equations in holomorphic form and show how this simplifies their structure. The holomorphic formulation is thus both a fundamental part of superstrata as well as an effective tool for their construction. In addition, we demonstrate that holomorphy provides a powerful tool in establishing the smoothness of our solutions without constraining the underlying functions. We also exhibit new families of solutions in which the momentum waves of the superstrata are highly localized at infinity but diffuse and spread into the infra-red limit in the core of the superstratum. Our work also leads to some results that can be tested within the dual CFT.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS1975

Requirements for implementation of Kuessner and Wagner indicial lift growth functions into the FLEXSTAB computer program system for use in dynamic loads analyses

General requirements for dynamic loads analyses are described. The indicial lift growth function unsteady subsonic aerodynamic representation is reviewed, and the FLEXSTAB CPS is evaluated with respect to these general requirements. The effects of residual flexibility techniques on dynamic loads analyses are also evaluated using a simple dynamic model.

Miller, R. D.↗
NASA NTRS1980

Proposed method for determining the thickness of glass in solar collector panels

An analytical method was developed for determining the minimum thickness for simply supported, rectangular glass plates subjected to uniform normal pressure environmental loads such as wind, earthquake, snow, and deadweight. The method consists of comparing an analytical prediction of the stress in the glass panel to a glass breakage stress determined from fracture mechanics considerations. Based on extensive analysis using the nonlinear finite element structural analysis program ARGUS, design curves for the structural analysis of simply supported rectangular plates were developed. These curves yield the center deflection, center stress and corner stress as a function of a dimensionless parameter describing the load intensity. A method of estimating the glass breakage stress as a function of a specified failure rate, degree of glass temper, design life, load duration time, and panel size is also presented.

Moore, D. M.↗
NASA NTRS1990

Molecular dynamics of liquid SiO2 under high pressure

The molecular dynamics of pure SiO2 liquids was investigated up to pressures of 20 GPa at 4000 K using 252, 498, 864, and 1371 particles. The results obtained suggest that the pressure-induced maxima in the self-diffusion coefficients of both oxygen and silicon are dependent on the system size. In the case of larger systems, the maximum decreases and shifts to lower pressures. Changes in the velocity autocorrelation function with increasing pressure are described. The populations of anomalously coordinated silicon and oxygen are then discussed as a function of pressure and system size.

Rustad, James R.↗
NASA NTRSDate not supplied

F-ANG+: A 3-D Augmented-Stencil Face-Averaged Nodal-Gradient Cell-Centered Finite-Volume Method for Hypersonic Flows

We describe the extension of a 2-D simplified face-averaged nodal-gradient (F-ANG) method to 3-D and demonstrate that the 3-D simplified F-ANG method is accomplished by augmenting the nodecentered gradient least squares stencil. This augmented stencil F-ANG method is shown to result in advection and diffusion schemes that are stable for hexahedral, prismatic, pyramidal and tetrahedral cells without having to resort to cell-averaged nodal gradients. In addition, we describe the modifications to the augmented stencil required to support the use of wall function boundary conditions. Finally we describe a consistent, face-stencil based multi-dimensional limiter procedure (MLP), and show it to be fully consistent and compatible with the linearity-preserving unstructured- MUSCL (LP-U-MUSCL) scheme for all values of kappa. These methods and schema are implemented in the cell-centered finite-volume code VULCAN-CFD, which is then used to investigate whether the robustness improvements demonstrated in 2-D carry over to 3-D by computing hypersonic flows using mixed-element grids as well as highly adapted tetrahedral grids.

Weighted Least-Squares↗
NASA NTRS2020

Pattern Identification - A Foundation for Research in the Emphasis of Design Patterns in Systems Engineering and Knowledge Capture

Pattern Language describes the morphology and functionality of a system in the absence of design particulars. Harnessing this capability will provide the Systems Engineering discipline a means of managing the development of increasingly complex systems with increasingly distributed design teams while capturing and retaining knowledge for future generations. Pattern Language is a syntax for describing, and structurally relating, design patterns. Design patterns contextually describe the application of domain knowledge in the engineered solution to the force balance problem. The parallels between pattern recognition and application, as a fundamental stage of human learning, and pattern observation within a complex system, suggests pattern language may be a valuable tool in the capture and dissemination of knowledge. Pattern application has enjoyed considerable study over the last several decades, however much of this work has focused on the replication of design particulars. This work returns to the roots of Pattern Language and explores the utility of patterns as an architectural description and guide, and knowledge capture method, for complex system development beginning with the identification of a time proven design pattern.

Russell, Samuel P.↗
DOE OSTI2021

Impact of shell structure on the fusion of neutron-rich mid-mass nuclei

The influence of shell effects on fusion of mid-mass nuclei is explored using isotopic chains of K and Ar ions on an oxygen target. Comparison of the reduced excitation functions reveals that the fusion cross section for the open neutron-shell projectile nuclei 41 K and 45 K is systematically larger than for the closed neutron-shell projectiles 39 K and 47 K. Furthermore, the São Paulo fusion model using matter densities from systematics fails to describe the measured excitation functions. Use of more realistic densities from a Dirac-Hartree-Bogoliubov (DHB) approach performs significantly better though it still overpredicts the closed-shell nuclei.

39 ≤ A ≤ 58↗
NASA NTRS2004

On Study of Air/Space-borne Dual-Wavelength Radar for Estimates of Rain Profiles

In this study, a framework is discussed to apply air/space-borne dual-wavelength radar for the estimation of characteristic parameters of hydrometeors. The focus of our study is on the Global Precipitation Measurements (GPM) precipitation radar, a dual-wavelength radar that operates at Ku (13.8 GHz) and Ka (35 GHz) bands. As the droplet size distributions (DSD) of rain are expressed as the Gamma function, a procedure is described to derive the median volume diameter (D(sub 0)) and particle number concentration (N(sub T)) of rain. The correspondences of an important quantity of dual-wavelength radar, defined as deferential frequency ratio (DFR), to the D(sub 0) in the melting region are given as a function of the distance from the 0 C isotherm. A self-consistent iterative algorithm that shows a promising to account for rain attenuation of radar and infer the DSD without use of surface reference technique (SRT) is examined by applying it to the apparent radar reflectivity profiles simulated from the DSD model and then comparing the estimates with the model (true) results. For light to moderate rain the self-consistent rain profiling approach converges to unique and correct solutions only if the same shape factors of Gamma functions are used both to generate and retrieve the rain profiles, but does not converges to the true solutions if the DSD form is not chosen correctly. To further examine the dual-wavelength techniques, the self-consistent algorithm, along with forward and backward rain profiling algorithms, is then applied to the measurements taken from the 2nd generation Precipitation Radar (PR-2) built by Jet Propulsion Laboratory. It is found that rain profiles estimated from the forward and backward approaches are not sensitive to shape factor of DSD Gamma distribution, but the self-consistent method is.

Liao, Liang↗
DOE OSTI2017

Functional Characterization of Four Putative δ1-Pyrroline-5-Carboxylate Reductases from Bacillus subtilis

In most living organisms, the amino acid proline is synthesized starting from both glutamate and ornithine. In prokaryotes, in the absence of an ornithine cyclodeaminase that has been identified to date only in a small number of soil and plant bacteria, these pathways share the last step, the reduction of δ1-pyrroline-5-carboxylate (P5C) catalyzed by P5C reductase (EC 1.5.1.2). In several species, multiple forms of P5C reductase have been reported, possibly reflecting the dual function of proline. Aside from its common role as a building block of proteins, proline is indeed also involved in the cellular response to osmotic and oxidative stress conditions. Genome analysis of Bacillus subtilis identifies the presence of four genes (ProH, ProI, ProG, and ComER) that, based on bioinformatic and phylogenic studies, were defined as respectively coding a putative P5C reductase. Here we describe the cloning, heterologous expression, functional analysis and small-angle X-ray scattering studies of the four affinity-purified proteins. Results showed that two of them, namely ProI and ComER, lost their catalytic efficiency or underwent subfunctionalization. In the case of ComER, this could be likely explained by the loss of the ability to form a dimer, which has been previously shown to be an essential structural feature of the catalytically active P5C reductase. The properties of the two active enzymes are consistent with a constitutive role for ProG, and suggest that ProH expression may be beneficial to satisfy an increased need for proline.

59 BASIC BIOLOGICAL SCIENCES↗
NASA NTRS1982

Intagliated phosphor screen image tube project

The production and evaluation of a magnetic focus image tube for astronomical photography that has an intagliated phosphor screen is described. The modulation transfer function of such a tube was measured by electronic means and by film tests, and the results compared with tubes of more conventional construction. The physical properties of the image tube and film combination, the analytical model of the optical interface, and the salient features of the intagliated screen tube are described. The results of electronic MTF tests of the intagliated image tube and of the densitometry of the tube and film test samples are presented. It is concluded that the intagliated screen is a help, but that the thickness of the photographic film is also important.

Hertzel, R. J.↗
DOE OSTI2025

Statistical evaluation of microscale stress conditions leading to void nucleation in the weak shock regime

Here, we investigate the heterogeneity of the stress state driven by anisotropic deformation response at the single crystal level through five statistical volume element (SVE) calculations of polycrystalline BCC tantalum. This work focuses on grain boundaries as a prominent material defect type prone to void nucleation based upon experimental observations of predominantly intergranular void nucleation in this material. The SVEs are constructed to be statistically representative of larger volumes of material and are meshed such that mean and standard deviation of grain size and orientation information is reconstructed. The computational meshes feature hexahedral (brick) elements and smooth conformal grain boundaries where significant stress concentration is known to occur, a tail effect of interest in the extreme events process of dynamic ductile damage. An existing micromechanical crystallographic plasticity model shown to capture the single crystal behavior of BCC tantalum well is used to perform the polycrystal calculations. The model includes representation of the non-Schmid effect of non-planar screw dislocation kinetics in tantalum. A three-dimensional stress state time profile predicted by damage modeling of a flyer plate impact experiment is applied as boundary conditions to each SVE. Resulting grain boundary stress state statistics are strongly non-Gaussian. Significant structural evolution is observed within the compressive hold before unloading into tension in the stress profile. Strong angular dependence of grain boundary traction magnitude with shock direction is observed. Non-Schmid effects continue to suggest their influence on propensity of microstructural defect types to nucleate voids. A general void nucleation criterion is proposed using probability theory. The general framework is specified to polycrystalline BCC tantalum in the weak shock regime to include the SVE calculations and literature molecular dynamics calculations of grain boundary void nucleation strength. Probability density functions (PDFs) are used to describe the interaction between the local stress state heterogeneity and the distributed grain boundary void nucleation strength state. A causation entropy maximization procedure removes the requirement for ad hoc selection of a PDF functional form and provides a rigorous procedure for data-based PDF determination. The resulting physically informed PDF describes the spatial appearance frequency of nucleated voids as a function of applied macroscale pressure. Lower length scale physics are thus packaged in a precise and computationally efficient way to provide computational plasticity insight to macroscale dynamic ductile damage models.

36 MATERIALS SCIENCE↗