SEARCH · Search NASA

Results for “Distributed Propulsion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,225 records · Page 68

All sources NASA NTRS DOE OSTI

NASA NTRS2021

Ice-Crystal Icing Investigation on a Honeywell Uncertified Research Engine in an Altitude Simulation Icing Facility

A Honeywell Uncertified Research Engine was exposed to various ice-crystal conditions in the NASA Propulsion Systems Laboratory (PSL). Simulations using NASA's one-dimensional (1D) Icing Risk Analysis tool were used to determine potential inlet conditions that could lead to ice-crystal accretion along the inlet of the core flowpath and into the high-pressure compressor. Baseline conditions were established, and parameters were varied to observe accretion characteristics. Data were acquired at altitudes varying from 5 kft to 45 kft, at nominal ice particle median volumetric diameters from 20 µm to 100 µm, and total water contents of 1 g/m3 to 12 g/m3. Metal temperatures were acquired for the inlet guide vane and vane stators 1–2. In situ measurements of the particle size distribution were acquired upstream and downstream of the engine fan face in order to study particle breakup behavior. Cameras were installed in the engine to capture ice accretions at the leading edge of the fan stator, splitter lip, and inlet guide vane. The goal of this study was to understand the key parameters of accretion, acquire particle breakup data aft of the fan, and generate a unique icing dataset for model development. Significant particle breakup downstream of the fan in the bypass was observed. The metal temperatures on the inlet guide vanes (IGVs) and stators show a temperature increase with increasing particle size. Accretion behavior at the fan stator and splitter lip across was very similar. However, accretion decreased with increasing particle size at the IGVs.

Ashlie B. Flegel↗

NASA NTRS2018

Lessons Learned from Recent Rapid Imaging of Earthquake Ruptures with Satellite Geodesy

Rapid determination of the location and extent of earthquake ruptures at the surface and at depth is helpful for disaster response, as it allows prediction of the likely area of major damage from the earthquake and can help with rescue and recovery planning. The Caltech-Jet Propulsion Laboratory (JPL) Advanced Rapid Imaging and Analysis (ARIA) project has responded to many recent large earthquakes to process geodetic data and help determine the location and extent of ruptures. With the increasing availability of near real-time data from the Global Positioning System (GPS) and other global navigation satellite system receivers in active tectonic regions, and with the shorter repeat times of many recent and newly launched radar satellites, geodetic data can now be obtained quickly after earthquakes or other disasters. We have been building an ARIA data system that can ingest, catalog, and process geodetic data and combine it with seismic analysis to estimate the fault rupture locations and slip distributions for large earthquakes that are on or near land.

Simons, Mark↗

NASA NTRS2021

Fit to be Tied: Embracing Tethered Robots for Exploring Extreme Planetary Environments

Tethers are supportive wires that could provide power, communication, and even science instrument capabilities to planetary rovers, landers, and future human settlements. Whether it be power distribution and optical communication connecting robots exploring extreme, undersea and deep subsurface environments, to your home office on Earth, we live, and will continue to live, in a predominantly ‘wired’ world. Accordingly, as humanity continues to push beyond Earth to exploring extreme planetary terrains like caves, cliffs, craters, and crevasses, and moves towards establishing human settlements on the Moon and Mars, we can expect tethers to play a major role. For exploration purposes, tethers are critical to enabling next-generation, science-focused missions to access high-value, resource-limited targets, where exploring rovers or astronauts lack direct communication or access to viable sunlight for solar power. NASA’s Jet Propulsion Laboratory (JPL) is formulating new mission concepts that could deploy robotic assets into some of the Solar System’s harshest and steepest terrain and, in many cases, tethers are the enabling technology. Examples include i) a rappelling rover to explore vertically along lunar pit walls to determine how the Moon formed, ii) tethered rovers to reach ice deposits on Mars and the Moon, iii) large, tether-deployed antenna structures to probe into the subsurface of a planet and/or look skyward to image the highly red-shifted, early universe, iv) probes that descend into the icy layers of Europa and Enceladus in search of subsurface oceans and, potentially, extant life, and v) science instruments that could be suspended on supportive tethers from balloons on Venus to directly image the surface and sample its clouds. This paper will present a survey of the state-of-the-art for tether related exploration of the solar system and chronicle ongoing work at JPL, which is leading to robust tether designs, high-power and communication transmission over multi-km distances, and highly capable, tether-based rover systems.

McGarey, Patrick↗

NASA NTRS1986

The Jet Propulsion Laboratory low-cost solar array project, 1974-1986

The overall objective of the photovoltaic program is to ensure that photovoltaic conversion systems play a significant role in the nation's energy supply by stimulating an industry capable of providing approximately 50 GWe of installed electricity generating capacity by the year 2000. In order to achieve this overall objective, several time-phased program goals have been defined. Near-term goals are to achieve photovoltaic flat-plate module or concentrator array prices of $2 per peak watt (1975 dollars) at an annual production rate of 20 peak megawatts in 1982. At this price level, energy costs should range from 100 to 200 mills/kwh. Mid-term goals are to achieve photovoltaic flat-plate module or concentrator array prices of $0.50 per peak watt (in 1975 dollars), and an annual production rate of 500 peak megawatts in 1986. Studies project that photovoltaic systems will begin to compete for both distributed and larger load-center utility-type applications and thereby open up significant markets for large-scale photovoltaic systems. Far term goals are to achieve the photovoltaic flat-plate module or concentrator array price goal of $0.10 to $0.30 per peak watt in 1990 (in 1975 dollars), and an annual production rate of 10 to 20 peak gigawatts in 2000. At this price range, energy cost should be in the range of 40 to 60 mills. kwh and be cost effective for utility applications. Achievement of these goals can make photovoltaic systems economically competitive with other energy sources for dispersed on-site applications as well as for central power generation.

Maycock, P. D.↗

DOE OSTI2021

Cybersecurity for Grid Connected eXtreme Fast Charging (XFC) Station (CyberX) (Final Scientific/Technical Report)

This report summarizes the activities conducted under the DOE VTO funded project DE- EE0008451, where ABB Inc. (ABB), in collaboration with Idaho National Laboratory (INL), APS Global (APS), and XOS Trucks (XOS) pursued the development of a cyber-resilient extreme fast charging (XFC) management system. This project entitled Cybersecurity for Grid Connected eXtreme Fast Charging (XFC) Station (CyberX) focuses on a resilient architecture for smart charging EV Supply Equipment (EVSE) device control and Coordinated Anomaly Detection System (CADS) features that can be added at the charging site depot level to increase cybersecurity. The project was split into two budget periods focused first on developing the threat model and resilient control concepts and second on testing, improving, and validating those developed resilient control algorithms and features with a focus on key vulnerabilities identified during the threat assessment portion of the project. During the first budget period of the CyberX project, the ABB led team focused on activities to identify, model, and quantitatively prioritize high-impact attack scenarios with potential cyber-physical effects while also modeling and developing concepts for a resilient control system that could securely address integration of DERs and other resources with EV charging. Development of the security focused XFC management system (XMS) was accomplished first by offline simulation using a developed XFC station or depot with 480V input level and simulating measurement inputs to monitoring and control systems in concept development. A representative distribution grid model was developed supporting an EV charging site model with BESS and 6 general EV charging models. These EV charging models allowed multiple configurations of charging level, multiple connected protection and measurement devices, and simulation function to show general compromise of EV, BESS, and protection features based on parallel threat analysis. During the second budget period, the EV site and supporting systems model was developed in more detail and converted from offline model to real-time to real-time with EV charging hardware in the loop (HIL). The resilient control architecture developed as concept in the first part of the project was further tested and validated for integration of local energy resources and XFC charging station site equipment while maintaining cybersecure operating principles. The proposed resilient architecture for smart charging and cybersecurity features consists of two main concepts developed and tested within the project. The first concept is an XFC management system (XMS) consisting of a hardware gateway, software platform, and Supervisory Control and Data Acquisition (SCADA) or Distribution Management System integration components. The second concept is a Coordinated Anomaly Detection System (CADS) which forms a primarily software-related subsystem of the total CyberX solution focused on monitoring system measurements, estimation of measurement states, and predicting current at the utility point of interaction based on machine learning for anomaly detection.

33 ADVANCED PROPULSION SYSTEMS↗

NASA NTRS2010

An Analysis of Recent Major Breakups in he Low Earth Orbit Region

Of the 190 known satellite breakups between 1961 and 2006, only one generated more than 500 cataloged fragments. The event was the explosion of the Pegasus Hydrazine Auxiliary Propulsion System in 1996, adding 713 fragments to the U.S. Satellite Catalog. Since the beginning of 2007; however, the near-Earth environment has been subjected to several major breakups, including the Fengyun-1C anti-satellite test and the explosion of Briz-M in 2007, the unusual breakup of Cosmos 2421 in 2008, and the collision between Iridium 33 and Cosmos 2251 in 2009. Combined, these events added more than 5000 large (> or equal 10 cm) fragments to the environment. Detailed analysis of the radar cross section measurements and orbit histories of the fragments from these major events reveals several unusual characteristics in their size and area-to-mass ratio distributions. The characteristics could be related to the material composition of the parent vehicles, the nature of the breakup, and the composition and physical property of the fragments. In addition, the majority of these fragments are expected to remain in orbit for at least decades. Their long-term impact to the environment is analyzed using the NASA orbital debris evolutionary model, LEGEND. Descriptions of these analyses and a summary are included in this paper.

Liou, Jer-Chyi↗

NASA NTRSDate not supplied

BioSentinel: Forging the path for Deep Space CubeSat Missions

The BioSentinel mission was launched in 2022 aboard the SLS launch vehicle as part of the Artemis-I campaign and continues mission operations into 2024. The 6U CubeSat has been characterizing deep space radiation at large distances from Earth. This presentation gives a status of the mission performance to date, as well as some of the lessons learned from project. BioSentinel has achieved unprecedented performance as an SLS secondary payload due to preparation, planning, and a robust design. Pre-launch antenna and interface testing with both DSN and ESA confirmed command and data pathways and allowed for operational flexibility in the critical early hours post-deployment. Mission Operations simulations prior to launch identified potential risks and trained operators to respond in flight, preparing the team to react quickly and successfully to detumble the spacecraft and enter a power-positive state. The spacecraft would not have survived without the inclusion of the trailblazing 3D-printed composite cold gas propulsion system. The non-standard tank geometry enabled efficient use of the limited space available in the CubeSat form factor as well as the capability to detumble the spacecraft and manage momentum for extended mission durations, while providing sufficient margin to execute potential delta-V maneuvers. Following the conclusion of the primary science mission, the Linear Energy Transfer (LET) Spectrometer has continued to collect solar and galactic radiation data from its unique location in heliocentric orbit. The free space dataset offered by the BioSentinel LET is a valuable source of data for both model validation and future mission planning. As the spacecraft travels farther from Earth it is poised to provide longitudinally distributed measurements of solar particle events during solar maximum. NASA Ames led development of the BioSentinel spacecraft to operate for long durations in deep space. The novel subsystems and COTS components that comprise the BioSentinel bus can serve as a template for future deep space missions, while the lessons the team has learned from well over a year of continuous operations will enable improved performance in the generation of deep space CubeSat missions.

BioSentinel↗

DOE OSTI2018

Regional Supply of Hydrogen

Analysis focuses on support of geographic and temporal distribution of hydrogen demand for light duty vehicle markets in the US. Demand analysis leverages existing hydrogen infrastructure and produces competitive supply chain selection for incremental production, delivery and retail installations from 2020 through 2040. This analysis assesses a novel hydrogen delivery pathway of the Hydrogen Grid, which delivers dispensing pressure hydrogen via intra-city pipelines to retail stations. Modelling leverages NREL's SERA model.

30 DIRECT ENERGY CONVERSION↗

NASA NTRS1996

Low Crossover Polymer Electrolyte Membranes for Direct Methanol Fuel Cells

Direct Methanol Fuel Cells (DMFC's) using polymer electrolyte membranes are promising power sources for portable and vehicular applications. State of the art technology using Nafion(R) 117 membranes (Dupont) are limited by high methanol permeability and cost, resulting in reduced fuel cell efficiencies and impractical commercialization. Therefore, much research in the fuel cell field is focused on the preparation and testing of low crossover and cost efficient polymer electrolyte membranes. The University of Southern California in cooperation with the Jet Propulsion Laboratory is focused on development of such materials. Interpenetrating polymer networks are an effective method used to blend polymer systems without forming chemical links. They provide the ability to modify physical and chemical properties of polymers by optimizing blend compositions. We have developed a novel interpenetrating polymer network based on poly (vinyl - difluoride)/cross-linked polystyrenesulfonic acid polymer composites (PVDF PSSA). Sulfonation of polystyrene accounts for protonic conductivity while the non-polar, PVDF backbone provides structural integrity in addition to methanol rejection. Precursor materials were prepared and analyzed to characterize membrane crystallinity, stability and degree of interpenetration. USC JPL PVDF-PSSA membranes were also characterized to determine methanol permeability, protonic conductivity and sulfur distribution. Membranes were fabricated into membrane electrode assemblies (MEA) and tested for single cell performance. Tests include cell performance over a wide range of temperatures (20 C - 90 C) and cathode conditions (ambient Air/O2). Methanol crossover values are measured in situ using an in-line CO2 analyzer.

Prakash, G. K. Surya↗

DOE OSTI2017

Isolation contactor state control system

A controller area network (CAN) installed on a hybrid electric vehicle provides one node with control of high voltage power distribution system isolation contactors and the capacity to energize a secondary electro-mechanical relay device. The output of the secondary relay provides a redundant and persistent backup signal to the output of the node. The secondary relay is relatively immune to CAN message traffic interruptions and, as a result, the high voltage isolation contactor(s) are less likely to transition open in the event that the intelligent output driver should fail.

33 ADVANCED PROPULSION SYSTEMS↗

NASA NTRS1987

New very high resolution radar studies of the Moon

As part of an effort to further understand the geologic utility of radar studies of the terrestrial planets, investigators at the Hawaii Institute of Geophysics are collaborating with NEROC Haystack Observatory, MIT and the Jet Propulsion Laboratory in the analysis of existing 3.8 and 70 cm radar images of the Moon, and in the acquisition of new data for selected lunar targets. The intent is to obtain multi-polarization radar images at resolutions approaching 75 meters (3.8 cm wavelength) and 400 meters (70 cm wavelength) for the Apollo landing sites (thereby exploiting available ground truth) or regions covered by the metric camera and geochemical experiments onboard the command modules of Apollos 15, 16 and 17. These data were collected in both like- and cross-polarizations, and, in the case of the 70 cm data, permit the phase records to be used to assess the scattering properties of the surface. The distribution of surface units on the Moon that show a mismatch between the surface implied by like- and cross-polarized scattering data is being analyzed, based on the scattering models of Evans and Hagfors.

Mouginis-Mark, Peter J.↗

NASA NTRS2013

Using the Flow-3D General Moving Object Model to Simulate Coupled Liquid Slosh - Container Dynamics on the SPHERES Slosh Experiment: Aboard the International Space Station

The SPHERES Slosh Experiment (SSE) is a free floating experimental platform developed for the acquisition of long duration liquid slosh data aboard the International Space Station (ISS). The data sets collected will be used to benchmark numerical models to aid in the design of rocket and spacecraft propulsion systems. Utilizing two SPHERES Satellites, the experiment will be moved through different maneuvers designed to induce liquid slosh in the experiment's internal tank. The SSE has a total of twenty-four thrusters to move the experiment. In order to design slosh generating maneuvers, a parametric study with three maneuvers types was conducted using the General Moving Object (GMO) model in Flow-30. The three types of maneuvers are a translation maneuver, a rotation maneuver and a combined rotation translation maneuver. The effectiveness of each maneuver to generate slosh is determined by the deviation of the experiment's trajectory as compared to a dry mass trajectory. To fully capture the effect of liquid re-distribution on experiment trajectory, each thruster is modeled as an independent force point in the Flow-3D simulation. This is accomplished by modifying the total number of independent forces in the GMO model from the standard five to twenty-four. Results demonstrate that the most effective slosh generating maneuvers for all motions occurs when SSE thrusters are producing the highest changes in SSE acceleration. The results also demonstrate that several centimeters of trajectory deviation between the dry and slosh cases occur during the maneuvers; while these deviations seem small, they are measureable by SSE instrumentation.

Schulman, Richard↗

NASA NTRS2006

Numerical Propulsion System Simulation

The NASA Glenn Research Center, in partnership with the aerospace industry, other government agencies, and academia, is leading the effort to develop an advanced multidisciplinary analysis environment for aerospace propulsion systems called the Numerical Propulsion System Simulation (NPSS). NPSS is a framework for performing analysis of complex systems. The initial development of NPSS focused on the analysis and design of airbreathing aircraft engines, but the resulting NPSS framework may be applied to any system, for example: aerospace, rockets, hypersonics, power and propulsion, fuel cells, ground based power, and even human system modeling. NPSS provides increased flexibility for the user, which reduces the total development time and cost. It is currently being extended to support the NASA Aeronautics Research Mission Directorate Fundamental Aeronautics Program and the Advanced Virtual Engine Test Cell (AVETeC). NPSS focuses on the integration of multiple disciplines such as aerodynamics, structure, and heat transfer with numerical zooming on component codes. Zooming is the coupling of analyses at various levels of detail. NPSS development includes capabilities to facilitate collaborative engineering. The NPSS will provide improved tools to develop custom components and to use capability for zooming to higher fidelity codes, coupling to multidiscipline codes, transmitting secure data, and distributing simulations across different platforms. These powerful capabilities extend NPSS from a zero-dimensional simulation tool to a multi-fidelity, multidiscipline system-level simulation tool for the full development life cycle.

Naiman, Cynthia↗

DOE OSTI2023

Markov Chain Monte Carlo Parameter Estimation of Deflagration Losses in a Rotating Detonation Engine

One of the practical challenges of the studies of rotating detonation engines (RDEs) is the direct estimation of losses from experimental measurements. This study attempts at resolving this limitation by combining a reduced order model (ROM) of the detonation wave characteristics with a Markov chain Monte Carlo parameter estimation framework. The model considers simple deflagration losses and the overall impact of deflagration on RDE performance. To evaluate this model, a Markov Chain Monte Carlo (MCMC) sampling technique was applied to estimate the loss parameters within the model for a set of conditions operated in hydrogen-air over a range of mass flow rates and equivalence ratios. The MCMC parameter estimation framework allowed for the determination of a posterior distribution of the loss parameters for each test condition, an examination of the correlation between the loss parameters and measured performance metrics of the RDE, and an uncertainty propagation of these parameters. The predicted model loss parameters were then compared to indirect experimental measurements of the deflagration combustion fractions to evaluating the validity of the approach, and shed light on the benefits and drawbacks of the model, measurement techniques, and the estimation framework.

33 ADVANCED PROPULSION SYSTEMS↗

NASA NTRS2000

Supplier's Status for Critical Solid Propellants, Explosive, and Pyrotechnic Ingredients

In the early 1970's a program was initiated at the Naval Surface Warfare Center/Indian Head Division (NSWC/IHDIV) to address the well-known problems associated with availability and suppliers of critical ingredients. These critical ingredients are necessary for preparation of solid propellants and explosives manufactured by the Navy. The objective of the program was to identify primary and secondary (or back-up) vendor information for these critical ingredients, and to develop suitable alternative materials if an ingredient is unavailable. In 1992 NSWC/IHDIV funded Chemical Propulsion Information Agency (CPIA) under a Technical Area Task (TAT) to expedite the task of creating a database listing critical ingredients used to manufacture Navy propellant and explosives based on known formulation quantities. Under this task CPIA provided employees that were 100 percent dedicated to the task of obtaining critical ingredient suppliers information, selecting the software and designing the interface between the computer program and the database users. TAT objectives included creating the Explosive Ingredients Source Database (EISD) for Propellant, Explosive and Pyrotechnic (PEP) critical elements. The goal was to create a readily accessible database, to provide users a quick-view summary of critical ingredient supplier's information and create a centralized archive that CPIA would update and distribute. EISD funding ended in 1996. At that time, the database entries included 53 formulations and 108 critical used to manufacture Navy propellant and explosives. CPIA turned the database tasking back over to NSWC/IHDIV to maintain and distribute at their discretion. Due to significant interest in propellant/explosives critical ingredients suppliers' status, the Propellant Development and Characterization Subcommittee (PDCS) approached the JANNAF Executive committee (EC) for authorization to continue the critical ingredient database work. In 1999, JANNAF EC approved the PDCS panel task. This paper is designed to emphasize the necessity of maintaining a JANNAF community supported database, which monitors PEP critical ingredient suppliers' status. The final product of this task is a user friendly, searchable database that provides a quick-view summary of critical ingredient supplier's information. This database must be designed to serve the needs of JANNAF and the propellant and energetic commercial manufacturing community as well. This paper provides a summary of the type of information to archive each critical ingredient.

Sims, B. L.↗

NASA NTRS2002

Influence of Cooling Channel Geometry on the Thermal Response in Silicon Nitride Plates Studied

Engine manufacturers are continually attempting to improve the performance and efficiency of internal combustion engines. Usually they raise the operating temperature or reduce the cooling air requirement for the hot section turbine components. However, the success of these attempts depends on finding materials that are lightweight, are strong, and can withstand high temperatures. Ceramics are among the top candidate materials considered for such harsh applications. They hold low-density, high-temperature strength, and thermal conductivity, and they are undergoing investigation as potential materials for replacing nickel-base alloys and superalloys that are currently used for engine hot-section components. Ceramic structures can withstand higher operating temperatures and a harsh combustion environment. In addition, their low densities relative to metals help reduce component mass. The long-term objectives of the High Temperature Propulsion Components (HOTPC) Project are to develop manufacturing technology, thermal and environmental barrier coatings (TBC/EBC), and the analytical modeling capability to predict thermomechanical stresses in minimally cooled silicon nitride turbine nozzle vanes under simulated engine conditions. Two- and three-dimensional finite element analyses with TBC were conducted at the NASA Glenn Research Center. Nondestructive evaluation was used to determine processing defects. The study included conducting preliminary parametric analytical runs of heat transfer and stress analyses under steady-state conditions to demonstrate the feasibility of using cooled Si3N4 parts for turbine applications. The influence of cooling-channel shapes (such as circular, square, and ascending-order cooling channels) on cooling efficiency and thermal stresses was investigated. Temperature distributions were generated for all cases considered under both cooling and no-cooling conditions, with air being the cooling medium. The table shows the magnitude of the maximum and minimum temperature obtained for the plates under air cooling. Each channel's cross-sectional shape delivered a different temperature; however, the two-dimensional analyses for circular and square or equal-side rectangular holes produced close results. Moreover, the model of the panel with ascending order cooling channels experienced the lowest temperature. A difference of near 260 C was found among the three cooling-hole configurations investigated. The ascending-order cooling channels arrangement showed superior performance by attaining the lowest temperature (1077 C) in comparison to the circular (1379 C) and square (1343 C) channels for the same cooling-hole size. This indicates that the panel with ascending-order cooling channels is the most suitable configuration regardless of the complexity involved in its manufacture. More details pertaining to this study are reported.

Abdul-Aziz, Ali↗

NASA NTRS2005

Ability of Impedance-Based Health Monitoring To Detect Structural Damage of Propulsion System Components Assessed

Impedance-based structural-health-monitoring uses piezoelectric (PZT) patches that are bonded onto or embedded in a structure. Each individual patch behaves as both an actuator of the surrounding structural area as well as a sensor of the structural response. The size of the excited area varies with the geometry and material composition of the structure, and an active patch is driven by a sinusoidal voltage sweep. When a PZT patch is subjected to an electric field, it produces a mechanical strain; and when it is stressed, it produces an electric charge. Since the patch is bonded to the structure, driving a patch deforms and vibrates the structure. The structure then produces a localized dynamic response. This structural system response is transferred back to the PZT patch, which in turn produces an electrical response. The electromechanical impedance method is based on the principle of electromechanical coupling between the active sensor and the structure, which allows researchers to assess local structural dynamics directly by interrogating a distributed sensor array. Because of mechanical coupling between the sensor and the host structure, this mechanical effect is picked up by the sensor and, through electromechanical coupling inside the active element, is reflected in electrical impedance measured at the sensor s terminals.

Martin, Richard E.↗

NASA NTRS2017

Near Earth Network (NEN) CubeSat Communications

The NASA Near Earth Network (NEN) consists of globally distributed tracking stations, including NASA, commercial, and partner ground stations, that are strategically located to maximize the coverage provided to a variety of orbital and suborbital missions, including those in LEO (Low Earth Orbit), GEO (Geosynchronous Earth Orbit), HEO (Highly Elliptical Orbit), lunar and L1-L2 orbits. The NEN's future mission set includes and will continue to include CubeSat missions. The first NEN-supported CubeSat mission will be the Cubesat Proximity Operations Demonstration (CPOD) launching into LEO in 2017. The majority of the CubeSat missions destined to fly on EM-1, launching in late 2018, many in a lunar orbit, will communicate with ground-based stations via X-band and will utilize the NASA Jet Propulsion Laboratory (JPL)-developed IRIS (Satellite Communication for Air Traffic Management) radio. The NEN recognizes the important role CubeSats are beginning to play in carrying out NASAs mission and is therefore investigating the modifications needed to provide IRIS radio compatibility. With modification, the NEN could potentially expand support to the EM-1 (Exploration Mission-1) lunar CubeSats. The NEN could begin providing significant coverage to lunar CubeSat missions utilizing three to four of the NEN's mid-latitude sites. This coverage would supplement coverage provided by the JPL Deep Space Network (DSN). The NEN, with smaller apertures than DSN, provides the benefit of a larger beamwidth that could be beneficial in the event of uncertain ephemeris data. In order to realize these benefits the NEN would need to upgrade stations targeted based on coverage ability and current configuration ease of upgrade, to ensure compatibility with the IRIS radio. In addition, the NEN is working with CubeSat radio developers to ensure NEN compatibility with alternative CubeSat radios for Lunar and L1-L2 CubeSats. The NEN has provided NEN compatibility requirements to several radio developers who are developing radios that offer lower cost and, in some cases, more capabilities with fewer constraints. The NEN is ready to begin supporting CubeSat missions. The NEN is considering network upgrades to broaden the types of CubeSat missions that can be supported and is supporting both the CubeSat community and radio developers to ensure future CubeSat missions have multiple options when choosing a network for their communications support.

CubeSat↗