Search NASA⌕ Search

SEARCH · Search NASA

Results for “Reduced Defects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,225 records · Page 68

Intrinsic stress in ZrN thin films: Evaluation of grain boundary contribution from in situ wafer curvature and ex situ x-ray diffraction techniques

Low-mobility materials, like transition metal nitrides, usually undergo large residual stress when sputter-deposited as thin films. While the origin of stress development has been an active area of research for high-mobility materials, atomistic processes are less understood for low-mobility systems. In the present work, the contribution of grain boundary to intrinsic stress in reactively magnetron-sputtered ZrN films is evaluated by combining in situ wafer curvature measurements, providing information on the overall biaxial stress, and ex situ x-ray diffraction, giving information on elastic strain (and related stress) inside crystallites. The thermal stress contribution was also determined from the in situ stress evolution during cooling down, after deposition was stopped. The stress data are correlated with variations in film microstructure and growth energetics, in the 0.13-0.42 Pa working pressure range investigated, and discussed based on existing stress models. At low pressure (high energetic bombardment conditions), a large compressive stress is observed due to atomic peening, which induces defects inside crystallites but also promotes incorporation of excess atoms in the grain boundary. Above 0.3-0.4 Pa, the adatom surface mobility is reduced, leading to the build-up of tensile stress resulting from attractive forces between under-dense neighbouring column boundary and possible void formation, while crystallites can still remain under compressive stress.

36 MATERIALS SCIENCE↗

Wake-up effects in Si-doped hafnium oxide ferroelectric thin films

Hafnium oxide based ferroelectric thin films have shown potential as a promising alternative material for non-volatile memory applications. This work reports the switching stability of a Si-doped HfO{sub 2} film under bipolar pulsed-field operation. High field cycling causes a “wake-up” in virgin “pinched” polarization hysteresis loops, demonstrated by an enhancement in remanent polarization and a shift of negative coercive voltage. The rate of wake-up is accelerated by either reducing the frequency or increasing the amplitude of the cycling field. We suggest de-pinning of domains due to reduction of the defect concentration at bottom electrode interface as origin of the wake-up.

36 MATERIALS SCIENCE↗

Strictly monolayer large continuous MoS{sub 2} films on diverse substrates and their luminescence properties

Despite a tremendous interest on molybdenum disulfide as a thinnest direct band gap semiconductor, single step synthesis of a large area purely monolayer MoS{sub 2} film has not yet been reported. Here, we report a CVD route to synthesize a continuous film of strictly monolayer MoS{sub 2} covering an area as large as a few cm{sup 2} on a variety of different substrates without using any seeding material or any elaborate pretreatment of the substrate. This is achieved by allowing the growth to take place in the naturally formed gap between a piece of SiO{sub 2} coated Si wafer and the substrate, when the latter is placed on top of the former inside a CVD reactor. We propose a qualitative model to explain why the MoS{sub 2} films are always strictly monolayer in this method. The photoluminescence study of these monolayers shows the characteristic excitonic and trionic features associated with monolayer MoS{sub 2}. In addition, a broad defect related luminescence band appears at ∼1.7 eV. As temperature decreases, the intensity of this broad feature increases, while the band edge luminescence reduces.

36 MATERIALS SCIENCE↗

Critically Evaluated Energy Levels and Spectral Lines of Singly Ionized Indium (In II)

A comprehensive list of the best measured wavelengths in the In II spectrum has been compiled. Uncertainties of the wavelength measurements have been analyzed, and existing inconsistencies have been resolved. An optimized set of fine-structure energy levels that fits all observed wavelengths has been derived. Uncertainties of the energy level values have been reduced by an order of magnitude. An improved value of the ionization limit of In II has been determined by fitting quantum-defect and polarization formulas for several series of levels. Intensities of lines observed by different authors have been analyzed and converted to a uniform scale. A set of recommended values of radiative transition rates has been critically compiled, and uncertainties of these rates have been estimated. The hyperfine structure interval in the 5s 2 S ground state of In III has been determined from the measurements of the 5sng and 5snh series in In II.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Reducing Surface Recombination Velocity of Methylammonium-Free Mixed-Cation Mixed-Halide Perovskites via Surface Passivation

We control surface recombination in the mixed-cation, mixed-halide perovskite, FA0.83Cs0.17Pb(I0.85Br0.15)3, by passivating nonradiative defects with the polymerizable Lewis base (3-aminopropyl)trimethoxysilane (APTMS). We demonstrate average minority carrier lifetimes >4 µs, nearly single exponential monomolecular photoluminescence decays, and high external photoluminescence quantum efficiencies (>20%, corresponding to ~97% of the maximum theoretical quasi-Fermi-level splitting) at low excitation fluence. We confirm both the composition and valence band edge position of the FA0.83Cs0.17Pb(I0.85Br0.15)3 perovskite using multi-institutional, cross-validated, X-ray photoelectron spectroscopy and UV photoelectron spectroscopy measurements. We extend the APTMS surface passivation to higher bandgap double-cation (FA and Cs) compositions (1.7, 1.75, and 1.8 eV) as well as the widely used triple-cation (FA, MA, and Cs) composition. Finally, we demonstrate that the average surface recombination velocity decreases from ~1000 to ~10 cm/s post APTMS passivation for FA0.83Cs0.17Pb(I0.85Br0.15)3. Our results demonstrate that surface-mediated recombination is the primary nonradiative loss pathway in many methylammonium (MA)-free mixed-cation mixed-halide films with a range of different bandgaps, which is a problem observed for a wide range of perovskite active layers and reactive electrical contacts. Our study also provides insights to develop passivating molecules that help reduce surface recombination in MA-free mixed-cation mixed-halide films and indicates that surface passivation and contact engineering will enable near-theoretical device efficiencies with these materials.

14 SOLAR ENERGY↗

Ensemble Manufacturing Techniques for Steam Turbine Components Across Length Scales

Faster design to manufacturing requirements were sought for steam turbine components to meet the changing demands of today’s power grid of improved efficiency through operating temperature increases and enhanced operational flexibility from baseload to cyclic operations. Advances in multiple advanced manufacturing (AM) process enabled redesign of turbine components for extreme environments with the potential to reduce cost. AM is of particular interest to improve component functionality, higher temperature capability, and superior durability in large scale steam turbine applications. AM methods have an immense potential to open-up the design space by working directly with the 3D model to produce near-net shapes, enable fast design-manufacturing iterations, thereby significantly reducing product cost and lead-time up to 25 % from current baseline. However, these benefits cannot be fully realized due to the potential for unknown AM processing defects and their resultant effect upon component performance in service. Siemens is partnering with Oak Ridge National Laboratory (ORNL), Electric Power Research Institute (EPRI), and Connecticut Center for Advanced Technology (CCAT) to advance the knowledge of complex process-material interactions for desired microstructures and properties that are closely interlinked to component geometries across different length scales. The proposed program utilized an ensemble of multidisciplinary technologies to accelerate the development of materials, high-throughput experiments for their qualification, and design flexibility/topology optimization for repair/redesign of components to address critical failure mechanisms for improved performance and increased reliability of existing power plant components. The proposed activities, if successfully demonstrated for identified components, will enable paradigm shift in customized manufacturing and accelerated qualification/certification towards increased steam turbine component durability, increased turbine efficiency, and reduced CO 2 emissions in load-following environments compared to today’s technology. Technology maturation is built into the project as successful research will include customized process-component down-selection enabling AM methodologies to be incorporated directly into the existing supply chain. The specific activities of the proposed effort are: 1. Topology optimization of down-selected steam turbine parts that are amenable to additive and hybrid manufacturing for cost/performance improvement. 2. Process-structure-property relationships for five AM processes for steam turbine materials of interest to compare with conventional materials. 3. Perform part/assembly build process using advanced additive/hybrid machine tools followed by quality inspection of the built components for insight into qualification for production scale-up. Steam turbine rig testing of printed components under targeted, well monitored and characterized environmental conditions of for performance comparison of baseline and redesigned components.

36 MATERIALS SCIENCE↗

Impact of forming, welding, and electropolishing on pitting and the surface finish of SRF cavity niobium

A broad range of coupon electropolishing experiments are described to ascertain the mechanism(s) by which large defects are formed near superconducting radiofrequency (SRF) cavity welds. Cold-worked vs. annealed metal, the presence of a weld, and several variations of electropolishing (EP) parameters were considered. Pitting is strongly promoted by cold work and agitation of the EP solution. Welding also promotes pitting, but less so compared with the other factors above. Temperature increase during EP did not strongly affect glossiness or pitting, but the reduced viscosity made the electrolyte more susceptible to agitation. The experiments suggest that several factors that are rather benign alone are combined by the cavity forming, welding, and processing sequence to promote the formation of defects such as pits. Process changes to mitigate these risks are discussed.

43 PARTICLE ACCELERATORS↗

Defect-Mediated Diffusion Pathways in Spodumene Accelerate Lithium Transport

Lithium extraction from naturally occurring α-spodumene is hindered by poor lithium diffusivity, necessitating high-temperature phase transformation to a low-density β polymorph. Although β spodumene exhibits up to 5 orders of magnitude higher lithium-ion diffusivity, both phases have diffusion activation energies between 0.8 and 1 eV, indicating that polymorph density is not the controlling factor over diffusivity. We show that aluminum vacancies facilitate lithium-ion diffusion in α-spodumene by reducing the migration barrier from 2.4 to 0.9 eV. Bond valence site energy and nudged elastic band calculations show a new lithium local minimum site which promotes a one-dimensional percolation network by reducing the lithium intersite distance from 4.5 Å to 2.9 Å. However, aluminum vacancies are energetically unfavorable to percolate through the whole structure, resulting in very low net lithium diffusivity and highlighting the critical role of nonstoichiometric defects in facilitating lithium transport in rigid aluminosilicate structures.

Chemical structure↗

A core of cell wall proteins functions in wall integrity responses in Arabidopsis thaliana

Abstract Cell walls surround all plant cells, and their composition and structure are tightly regulated to maintain cellular and organismal homeostasis. In response to wall damage, the cell wall integrity (CWI) system is engaged to ameliorate effects on plant growth. Despite the central role CWI plays in plant development, our current understanding of how this system functions at the molecular level is limited. Here, we investigated the transcriptomes of etiolated seedlings of mutants of Arabidopsis thaliana with defects in three major wall polysaccharides, pectin ( quasimodo2 ), cellulose ( cellulose synthase3 je5 ), and xyloglucan ( xyloglucan xylosyltransferase1 and 2 ), to probe whether changes in the expression of cell wall‐related genes occur and are similar or different when specific wall components are reduced or missing. Many changes occurred in the transcriptomes of pectin‐ and cellulose‐deficient plants, but fewer changes occurred in the transcriptomes of xyloglucan‐deficient plants. We hypothesize that this might be because pectins interact with other wall components and/or integrity sensors, whereas cellulose forms a major load‐bearing component of the wall; defects in either appear to trigger the expression of structural proteins to maintain wall cohesion in the absence of a major polysaccharide. This core set of genes functioning in CWI in plants represents an attractive target for future genetic engineering of robust and resilient cell walls.

59 BASIC BIOLOGICAL SCIENCES↗

Regulation of gap junction function and Connexin 43 expression by cytochrome P450 oxidoreductase (CYPOR)

Highlights: {yields} Humans with severe forms of cytochrome P450 oxidoreductase (CYPOR) mutations show bone defects as observed in Antley-Bixler Syndrome. {yields} First report showing knockdown of CYPOR in osteoblasts decreased Connexin 43 (Cx43) protein levels. Cx43 is known to play an important role in bone modeling. {yields} Knockdown of CYPOR decreased Gap Junctional Intercellular Communication and hemichannel activity. {yields} Knockdown of CYPOR decreased Cx43 in mouse primary calvarial osteoblasts. {yields} Decreased Cx43 expression was observed at the transcriptional level. -- Abstract: Cytochrome P450 oxidoreductase (CYPOR) is a microsomal electron-transferring enzyme containing both FAD and FMN as co-factors, which provides the reducing equivalents to various redox partners, such as cytochromes P450 (CYPs), heme oxygenase (HO), cytochrome b{sub 5} and squalene monooxygenase. Human patients with severe forms of CYPOR mutation show bone defects such as cranio- and humeroradial synostoses and long bone fractures, known as Antley-Bixler-like Syndrome (ABS). To elucidate the role of CYPOR in bone, we knocked-down CYPOR in multiple osteoblast cell lines using RNAi technology. In this study, knock-down of CYPOR decreased the expression of Connexin 43 (Cx43), known to play a critical role in bone formation, modeling, and remodeling. Knock-down of CYPOR also decreased Gap Junction Intercellular Communication (GJIC) and hemichannel activity. Promoter luciferase assays revealed that the decrease in expression of Cx43 in CYPOR knock-down cells was due to transcriptional repression. Primary osteoblasts isolated from bone specific Por knock-down mice calvariae confirmed the findings in the cell lines. Taken together, our study provides novel insights into the regulation of gap junction function by CYPOR and suggests that Cx43 may play an important role(s) in CYPOR-mediated bone defects seen in patients.

60 APPLIED LIFE SCIENCES↗

High Efficiency m-plane LEDs on Low Defect Density Bulk GaN Substrates

Solid-state lighting is a key technology for reduction of energy consumption in the US and worldwide. In principle, by replacing standard incandescent bulbs and other light sources with sources based on light-emitting diodes (LEDs), ultimate energy efficiency can be achieved. The efficiency of LEDs has improved tremendously over the past two decades, however further progress is required for solid- state lighting to reach its full potential. The ability of an LED at converting electricity to light is quantified by its internal quantum efficiency (IQE). The material of choice for visible LEDs is Gallium Nitride (GaN), which is at the basis of blue-emitting LEDs. A key factor limiting the performance of GaN LEDs is the so-called efficiency droop, whereby the IQE of the LED decreases significantly at high current density. Despite decades of research, efficiency droop remains a major issue. Since high-current operation is necessary for practical lighting applications, reducing droop is a major challenge for the scientific community and the LED industry. Our approach to solving the droop issue is the use of newly available low-defect-density bulk GaN non-polar substrates. In contrast to the standard foreign substrates (sapphire, silicon carbide, silicon) used in the industry, we have employed native bulk GaN substrates with very low defect, density, thus ensuring exquisite material quality and high IQE. Whereas all commercial LEDs are grown along the c-plane crystal direction of GaN, we have used m-plane non-polar substrates; these drastically modify the physical properties of the LED and enable a reduction of droop. With this approach, we have demonstrated very high IQE performance and low droop. Our results focused on violet and blue LEDs. For these, we have demonstrated very high peak IQEs and current droops of 6% and 10% respectively (up to a high current density of 200A.cm-2). All these results were obtained under electrical operation. These high IQE and low droop values are in line with the program’s milestones. They demonstrate that bulk non-polar GaN substrates represent a disruptive technology for LED performance. Application of this technology to real-world products is feasible, provided that the cost of GaN substrates is compatible with the market’s requirement.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Crystal structure, microstructure and reducibility of LaNi{sub x}Co{sub 1-x}O{sub 3} and LaFe{sub x}Co{sub 1-x}O{sub 3} Perovskites (0<x<=0.5)

Nickel and iron substituted LaCoO{sub 3} with rhombohedrally distorted perovskite structure were obtained in the temperature range of 600-900 deg. C by thermal decomposition of freeze-dried citrates and by the Pechini method. The crystal structure, morphology and defective structure of LaCo{sub 1-x}Ni{sub x}O{sub 3} and LaCo{sub 1-x}Fe{sub x}O{sub 3} were characterized by X-ray diffraction and neutron powder diffraction, TEM and SEM analyses and electron paramagnetic resonance spectroscopy. The reducibility was tested by temperature programmed reduction with hydrogen. The products of the partial and complete reduction were determined by ex-situ XRD experiments. The replacement of Co by Ni and Fe led to lattice expansion of the perovskite structure. For perovskites annealed at 900 deg. C, there was a random Ni, Fe and Co distribution. The morphology of the perovskites does not depend on the Ni and Fe content, nor does it depend on the type of the precursor used. LaCo{sub 1-x}Ni{sub x}O{sub 3} perovskites (x>0.1) annealed at 900 deg. C are reduced to Co/Ni transition metal and La{sub 2}O{sub 3} via the formation of oxygen deficient Brownmillerite-type compositions. For LaCo{sub 1-x}Ni{sub x}O{sub 3} annealed at 600 deg. C, Co/Ni metal, in addition to oxygen-deficient perovskites, was formed as an intermediate product at the initial stage of the reduction. The interaction of LaCo{sub 1-x}Fe{sub x}O{sub 3} with H{sub 2} occurs by reduction of Co{sup 3+} to Co{sup 2+} prior to the Fe{sup 3+} ions. The reducibility of Fe-substituted perovskites is less sensitive towards the synthesis procedure in comparison with that of Ni substituted perovskites. - Graphical abstract: LaCo{sub 1-x}Ni{sub x}O{sub 3} and LaCo{sub 1-x}Fe{sub x}O{sub 3} with rhombohedrally distorted perovskite structure were obtained in the temperature range of 600-900 deg. C by thermal decomposition of freeze-dried La-Co/Ni(Fe)-citrates and by the Pechini method. The complete reduction of LaCo{sub 1-x}Ni{sub x}O{sub 3} with H{sub 2} proceeds to Co/Ni-metal and La{sub 2}O{sub 3}, while the interaction of LaCo{sub 1-x}Fe{sub x}O{sub 3} with H{sub 2} is not complete up to 700 deg. C. For LaCo{sub 1-x}Fe{sub x}O{sub 3}, the reaction proceeds by preferential oxidation of Co{sup 3+} to Co{sup 2+} without affecting Fe{sup 3+} ions.

36 MATERIALS SCIENCE↗

Properties of native defects in InI for potential radiation detector application

Heavy-metal halide semiconductors have attracted much interest recently for their potential applications in radiation detection because the large atomic numbers (high Z) of their constituent elements enable efficient radiation absorption and their large band gaps allow room temperature operation. However, defect properties of these halides and their connection to carrier transport are little known. In this paper, we present first-principles calculations on native defects in InI, which is a promising material for applications in room temperature radiation detection. The important findings are: (1) anion and cation vacancies (Schottky defects) form the dominant low-energy defects that can pin the Fermi level close to midgap, leading to high resistivity that is required for a good radiation detector material; (2) the anion vacancy in InI induces a deep electron trap, which should reduce electron mobility-lifetime product in InI; (3) low diffusion barriers of vacancies could be responsible for the observed polarization phenomenon at room temperature

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Modifications in the charge trap landscape in Hf 0.5 Zr 0.5 O 2 as a function of oxygen vacancy concentration observed with photoemission electron microscopy

Oxygen vacancies in Hf x Zr (1-x) O 2 (HZO) both contribute to stabilization of the ferroelectric orthorhombic phase and promote leakage pathways that limit the endurance of devices based on the material. Here, for this reason, the defect states of oxygen vacancies were investigated using photoemission electron microscopy (PEEM) and photoluminescence spectroscopy (PL), as their concentration was varied via ex situ laser exposure. Following a controlled oxygen vacancy reduction via visible (2.54 eV) laser dosing of HZO, deep-ultraviolet (DUV, 5.82 eV) PEEM was used to spatially probe the resulting mid-gap defect states and work function. Work function was found to increase monotonically with the laser-induced reduction in oxygen vacancy concentration culminating in a total increase near 70 meV. The change implies a Fermi level shift toward the valence band as the total available electron-filled charge states are reduced with the removal of oxygen vacancies. A reduction in charge states is corroborated by the observed lessening of both photoemission and photoluminescence intensities after laser dosing. The deduced position of the Fermi level is within a band of near-conduction band defect states produced by oxygen vacancies that are linked to endurance limiting leakage currents. Together, these results directly identify the primary role of oxygen vacancies on the defect states in HZO while demonstrating that laser exposure can be used for their modification.

42 ENGINEERING↗

Influence of ion energy and ion species on ion channeling in LiNbO{sub 3}

Ion irradiation of LiNbO{sub 3} causes the formation of defects due to nuclear as well as electronic energy deposition {epsilon}{sub n} and {epsilon}{sub e}, respectively. However, the defect formation is influenced by the orientation of the crystal. If the irradiation is performed along a low index crystallographic direction (on-axis) the defect distributions are strongly affected by ion channeling because the ions are prevented from close collisions with the target atoms so that the penetration range of the impinging ions is increased. In order to investigate the effect of {epsilon}{sub n} and {epsilon}{sub e} on damage formation LiNbO{sub 3} crystals were irradiated on- and off-axes using Si{sup +} and Cu{sup +} ions with energies ranging from 550 keV to 2 MeV. We demonstrate for on-axis irradiation that at low ion energies where {epsilon}{sub n} dominates the formation of defects, the defect distribution is shifted to larger depths compared to off-axis irradiation. The investigation of the shift shows a square-root dependence on both ion energy and ion species. Furthermore, on-axis irradiation was done using high-ion energies where defects are formed in the near-surface region due to electronic energy loss. Compared to off-axis irradiation a thinner amorphous surface layer was formed as a result of the reduced electronic energy loss in the case of on-axis irradiation. For on-axis irradiation {epsilon}{sub e} could be estimated in two different ways considering the layer thickness and the penetration range of the incident ions.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Enhanced visible light activity of nano-titanium dioxide doped with multiple ions: Effect of crystal defects

Titanium dioxide photocatalysts co-doped with iron(III) and lanthanum(III) have been prepared through a modified sol-gel method. Doping with Fe{sup 3+} resulted in a relatively lower anatase to rutile phase transformation temperature, while La{sup 3+} addition reduced the crystal growth and thus retarded the phase transformation of titania nanoparticles. The presence of Fe{sup 3+} ions shifted the absorption profile of titania to the longer wavelength side of the spectrum and enhanced the visible light activity. On the other hand, La{sup 3+} addition improved the optical absorption of titania nanoparticles. Both the dopants improved the life time of excitons by proper transferring and trapping of photoexcited charges. In the present work, considerable enhancement in photocatalytic activity under visible light was achieved through synergistic effect of optimum concentrations of the two dopants and associated crystal defects. - Graphical abstract: Photocatalytic activity studies indicate a synergistic effect of dopants and crystal defects leading to an enhanced photochemical activity. Highlights: Black-Right-Pointing-Pointer An aqueous sol-gel synthesis of Fe{sup 3+} and La{sup 3+} co-doped TiO{sub 2} is being reported. Black-Right-Pointing-Pointer Optical and microstructural properties of titania were modified by co-doping. Black-Right-Pointing-Pointer Enhanced activity of titania by the crystal defects is being reported.

36 MATERIALS SCIENCE↗

FTIR and Raman Spectroscopy of Reduced Graphene Oxide Carbon Nanoribbons and Graphene Oxide on Copper (Cu)

In the past couple of decades, carbon nanomaterials produced from graphene and graphite have emerged as one of the more important recently discovered substances. These carbon nanomaterials have been found to exhibit high levels of mechanical strength, thermal resistance, and electrical conductivity, thus having a multitude of applications. Therefore, it is important to identify and analyze their traits in order to maximize their effectiveness. Two spectroscopic techniques employed for such analyses of these materials are Fourier-Transform Infrared (FTIR) and Raman Spectroscopy. The advantages of FTIR and Raman include nondestructive analysis, relatively quick measurements under normal atmospheric conditions, and enhanced sensitivity with high resolution capacity. FTIR Spectroscopy was used in this research project to determine the effects of thermal exfoliation and photoreduction on the functionality groups of a carbon nanomaterial. Raman Spectroscopy was used in this research project to determine the effects of thermal exfoliation and photoreduction on the intensity of the disorder peak, which is greater in intensity if the carbon nanomaterial exhibits greater amounts of functionalities or defects in the graphitic material. There were two sample types which were analyzed with both FTIR and Raman Spectroscopy for the research project: graphene nanoribbons and graphene oxide. The m-grade graphene nanoribbons (GNRs) were produced from m-grade carbon nanotubes (CNTs) via Tour's method. The graphene oxide (GO) was produced from graphene via Tour's method, sonicated and centrifuged, dip-coated onto Copper (Cu) foil, and then photoreduced under a UV light source. FTIR measurements and analyses were conducted using a Jasco FTIR Spectrometer. Raman measurements and analyses were conducted using a Jasco Laser Raman Spectrometer. Tasks and techniques for this project included photoreduction, dip-coating, corrosion testing, FTIR and Raman data collection and analysis, and improvement of data collection for the Raman Spectrometer. GNRs exfoliated and reduced (deoxygenation) at 270 deg. C in air showed a significant decrease in O functionalities according to FTIR. However, Raman revealed that a large increase in graphene planar and edge defects are present as indicated by the disorder band at 1340 cm-1. Further optimization could be performed by thermal exfoliation at lower temperatures assuming a need for fewer structural defects. Graphene oxide coatings showed clear reduction with an increase with photoreduction time. Raman revealed that the reduced graphene oxide films had less disruption in the planar phonon lattice vibrations which indicates that the structure is returning to sp2 hybridization of pristine graphene without adding structural defects.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Synthesis and Catalytic Activity of Pt Monolayer on Pd Tetrahedral Nanocrystals with CO-adsorption-induced Removal of Surfactants

We synthesized the Pt monolayer shell-Pd tetrahedral core electrocatalysts that are notable for their high activity and stable performance. A small number of low-coordination sites and defects, and high content of the (1 1 1)-oriented facets on Pd tetrahedron makes them a suitable support for a Pt monolayer to obtain an active O{sub 2} reduction reaction (ORR) electrocatalyst. The surfactants, used to control size and shape of Pd tetrahedral nanoparticles, are difficult to remove and cause adverse effects on the ORR. We describe a simple and noninvasive method to synthesize high-purity tetrahedral Pd nanocrystals (TH Pd) by combining a hydrothermal route and CO adsorption-induced removal of surfactants. Poly(vinylpyrrolidone) (PVP), used as a protecting and reducing agent in hydrothermal reactions, is strongly bonded to the surface of the resulting nanocrystals. We demonstrate that PVP was displaced efficiently by adsorbed CO. A clean surface was achieved upon CO stripping at a high potential (1.0 V vs RHE). It played a decisive role in improving the activity of the Pt monolayer/TH Pd electrocatalyst for the ORR. Furthermore, the results demonstrate a versatile method for removal of surfactants from various nanoparticles that severely limited their applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗