Search NASA⌕ Search

SEARCH · Search NASA

Results for “STRESS DISTRIBUTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,225 records · Page 68

Matrix Cracking in Four Different 2D SiC/SiC Composite Systems

Silicon carbide fiber reinforced, silicon carbide matrix composites are some of the most advanced composite systems for high-temperature, high-stress applications in oxidizing environments. A basic area that needs to be understood for the purpose of material behavior modeling and optimization is the architectural, constituent, and mechanistic factors that contribute to non-linear stress-strain behavior. The mechanism that causes non-linear stress-strain in dense-matrix composites is the formation and propagation of bridged matrix cracks. In addition, the occurrence and propagation of matrix cracks controls the time-dependent strength-properties of these materials in oxidizing environments at elevated temperatures. A modal acoustic emission technique has been used to monitor and estimate the stress-dependent matrix cracking. Two different SiC matrix systems, chemical vapor infiltrated (CVI) and melt-infiltrated (MI), with two different SiC fiber reinforcement, Hi-Nicalon (trademark) and Sylramic (trademark) were compared. Even though the averages of the range where matrix cracking occurred for the composites varied by more than 0.1% in strain and almost 200 MPa in stress, the range or distribution for matrix cracking could be reduced to a narrow band of stress for CVI SiC and MI SiC composites if it were assumed that all matrix cracks emanate outside of the load-bearing fiber, interphase, CVI preform minicomposite. A simple relationship was determined to describe stress-dependent matrix cracking which can then be used to estimate the onset of large, bridged matrix cracks or for material behavior models.

Morscher, Gregory N.↗

Global Failure Modes in Composite Structures for High Altitudes

This report summarizes the accomplishments under the referenced grant. The work described was started under the guidance and supervision of the late Dr. James Stames as the technical contact. It was aimed at investigating the development of analysis tools to deal with the problem of rupture in reinforced structural skin of future composites-based aircraft. It was of particular interest to assess methods by which failure features reminiscent of cracks in metallic structures would develop and propagate in fiber reinforced structures in interaction with the reinforcing frame. To eventually achieve that goal it was necessary to first understand the stress or strain distribution at the front of such features so that interactions between such features and reinforcing agents could be assessed computationally. Thus the major emphasis here was on the assessment of damage front and methods on how to assess or characterize it. During the conduct of this research program Dr. Stames changed to a different NASA- internal assignment, which divorced him of the direct supervision of this grant. A student who was approximately % into the completion of his Ph.D. research needed to finish this work, and NASA funds were made available under Dr. Damodar Ambur, the successor Branch Manager for Dr. James Starnes, for the completion of this work. The current grant was the thus a new and fmal support increment for completion of the started research. Final reports for previous funding have been completed and submitted. Because of the interconnection of this last phase of the investigation with previous work it is deemed useful to make the Ph.D. thesis by Luis Gonzales the body of this report.

Knauss, W. G.↗

A New and General Formulation of the Parametric HFGMC Micromechanical Method for Three-Dimensional Multi-Phase Composites

The recent two-dimensional (2-D) parametric formulation of the high fidelity generalized method of cells (HFGMC) reported by the authors is generalized for the micromechanical analysis of three-dimensional (3-D) multiphase composites with periodic microstructure. Arbitrary hexahedral subcell geometry is developed to discretize a triply periodic repeating unit-cell (RUC). Linear parametric-geometric mapping is employed to transform the arbitrary hexahedral subcell shapes from the physical space to an auxiliary orthogonal shape, where a complete quadratic displacement expansion is performed. Previously in the 2-D case, additional three equations are needed in the form of average moments of equilibrium as a result of the inclusion of the bilinear terms. However, the present 3-D parametric HFGMC formulation eliminates the need for such additional equations. This is achieved by expressing the coefficients of the full quadratic polynomial expansion of the subcell in terms of the side or face average-displacement vectors. The 2-D parametric and orthogonal HFGMC are special cases of the present 3-D formulation. The continuity of displacements and tractions, as well as the equilibrium equations, are imposed in the average (integral) sense as in the original HFGMC formulation. Each of the six sides (faces) of a subcell has an independent average displacement micro-variable vector which forms an energy-conjugate pair with the transformed average-traction vector. This allows generating symmetric stiffness matrices along with internal resisting vectors for the subcells which enhances the computational efficiency. The established new parametric 3-D HFGMC equations are formulated and solution implementations are addressed. Several applications for triply periodic 3-D composites are presented to demonstrate the general capability and varsity of the present parametric HFGMC method for refined micromechanical analysis by generating the spatial distributions of local stress fields. These applications include triply periodic composites with inclusions in the form of a cavity, spherical inclusion, ellipsoidal inclusion, discontinuous aligned short fiber. A 3-D repeating unit-cell for foam material composite is simulated.

Haj-Ali, Rami↗

Application of Out-of-Plane Warping to Control Rotor Blade Twist

The goal of this ongoing study is to develop and demonstrate the feasibility of a blade actuation system to dynamically change the twist, and/or the camber, of an airfoil section and, consequently, alter the in-flight aerodynamic loading on the blade for efficient flight control. The required analytical and finite element tools are under development to enable an accurate and comprehensive aeroelastic assessment of the current Full-Blade Warping and 3D Warping Actuated Trailing Edge Flap concepts. The feasibility of the current concepts for swashplateless rotors and higher harmonic blade control is also being investigated. In particular, the aim is to complete the following objectives, some of which have been completed (as noted below) and others that are currently ongoing: i) Develop a Vlasov finite element model and validate against the ABAQUS shell models (completed). ii) Implement the 3D warping actuation concept within the comprehensive analysis code DYMORE. iii) Perform preliminary aeroelastic simulations of blades using DYMORE with 3D warping actuation: a) Investigate the blade behavior under 1 per/rev actuation. Determine whether sufficient twist can be generated and sustained to achieve primary blade control. b) Investigate the behavior of a trailing edge flap configuration under higher harmonic excitations. Determine how much twist can be obtained at the harmonics 2-5 per/rev. iv) Determine actuator specifications such as the power required, load and displacements, and identify the stress and strain distributions in the actuated blades. In general, the completion of Item ii) above will give an additional research capability in rotorcraft dynamics analyses, i.e., the capability to calculate the rotor blade twist due to warping, something that is not currently available in any of the existing comprehensive rotorcraft analyses.

VanWeddingen, Yannick↗

Bioinspired multilayered cellular composites with enhanced energy absorption and shape recovery

Inspired by the multiscale configuration of the microstructure of cork, the paper describes the design, 3D printing, and evaluation of a new type of multilayered cellular composite (MCC) structure composed of hard brittle and soft flexible phases. The mechanical behavior of 3D printed MCC structures have been investigated both experimentally and numerically. The experiments show that the MCC structure absorbs four times the amount of energy of a conventional cellular configuration under compressive strains up to 70%. Finite element simulations and 2D digital image correlation (DIC) also show that the multilayered architecture provides a more uniform strain distribution and higher stress transfer efficiency, with a resulting progressive failure mode rather than a catastrophic one. Cyclic loading tests demonstrate that the MCC structure also possesses exceptional shape recoverability under compressive deformations up to 40%. These remarkable performance characteristics result from synergies between the properties of the two constituent materials and the chosen multilayered cellular microstructure. The soft phase, in particular, plays a pivotal role in absorbing elastic energy during loading and then releasing the stored energy while unloading. The volume fraction of the soft phase is also essential to control energy absorption and the transition of failure modes. The deformation mechanisms demonstrated here are robust and applicable to other architected cellular materials across multiple length scales and suggest new ways to design lightweight and high-resilience structural materials.

bioinspired composites↗

Elevated Temperature Primary Load Design Method Using Pseudo Elastic-Perfectly Plastic Model

A new primary load design method for elevated temperature service has been developed. Codification of the procedure in an ASME Boiler and Pressure Vessel Code, Section III Code Case is being pursued. The proposed primary load design method is intended to provide the same margins on creep rupture, yielding and creep deformation for a component or structure that are implicit in the allowable stress data. It provides a methodology that does not require stress classification and is also applicable to a full range of temperature above and below the creep regime. Use of elastic-perfectly plastic analysis based on allowable stress with corrections for constraint, steady state stress and creep ductility is described. This approach is intended to ensure that traditional primary stresses are the basis for design, taking into account ductility limits to stress re-distribution and multiaxial rupture criteria.

Carter, Peter↗

Understanding Irreversible Degradation of Nb3Sn Wires with Fundamental Fracture Mechanics

Irreversible performance degradation of advanced Nb3Sn superconducting wires subjected to transverse or axial mechanical loading is a critical issue for the design of large-scale fusion and accelerator magnets such as ITER and LHC. Recent SULTAN tests indicate that most cable-in-conduit conductors for ITER coils made of Nb3Sn wires processed by various fabrication techniques show similar performance degradation under cyclic loading. The irreversible degradation due to filament fracture and local strain accumulation in Nb3Sn wires cannot be described by the existing strand scaling law. Fracture mechanic modeling combined with X-ray diffraction imaging of filament micro-crack formation inside the wires under mechanical loading may reveal exciting insights to the wire degradation mechanisms. We apply fundamental fracture mechanics with a singularity approach to study influence of wire filament microstructure of initial void size and distribution to local stress concentration and potential crack propagation. We report impact of the scale and density of the void structure on stress concentration in the composite wire materials for crack initiation. These initial defects result in an irreversible degradation of the critical current beyond certain applied stress. We also discuss options to minimize stress concentration in the design of the material microstructure for enhanced wire performance for future applications.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Effect of interconnect creep on long-term performance of SOFC of one cell stacks

Creep deformation becomes relevant for a material when the operating temperature is near or exceeds half of its melting temperature (in degrees of Kelvin). The operating temperatures for most of the solid oxide fuel cells (SOFC) under development in the SECA program are around 1073oK. High temperature ferritic alloys are potential candidates as interconnect (IC) materials and spacers due to their low cost and CTE compatibility with other SOFC components. Since the melting temperature of most stainless steel is around 1800oK, possible creep deformation of IC under the typical cell operating temperature should not be neglected. In this paper, the effects of interconnect creep behavior on stack geometry change and stress redistribution of different cell components are predicted and summarized. The goal of the study is to investigate the performance of the fuel cell stack by obtaining the fuel and air channel geometry changes due to creep of the ferritic stainless steel interconnect, therefore indicating possible SOFC performance change under long term operations. IC creep models were incorporated into SOFC-MP and Mentat FC, and finite element analyses were performed to quantify the deformed configuration of the SOFC stack under the long term steady state operating temperature. It is found that creep behavior of the ferritic stainless steel IC contributes to narrowing of both the fuel and the air flow channels. In addition, stress re-distribution of the cell components suggests the need for a compliant sealing material that also relaxes at operating temperature.

30 DIRECT ENERGY CONVERSION↗

A residual stress study in similar and dissimilar welds

Residual strain distributions in similar and dissimilar welds were measured using neutron diffraction (ND) method. Then, using three strain components, three-dimensional stress states were calculated. The results were used to determine the effect of the martensitic phase transformation and material properties on residual stress (RS) distribution. It was observed that smaller longitudinal RS was induced in the low carbon steel side of dissimilar weld when compared to its similar weld. Also, it was found that the transverse RS near and within the weld zone (WZ) in dissimilar weld exhibited a distinctive trend, with tensile mode reaching the yield strength of the base metal (BM). In order to characterize the WZ in dissimilar weld, we deployed optical microscopy, hardness, and energy dispersive X-ray spectroscopy (EDAX). This study not only provides further insight into the RS state in similar and dissimilar welds; it also delivers important consequences of phase transformation in the latter case.

36 MATERIALS SCIENCE↗

Methodology for Irradiation Creep Testing of SiC / SiC Composite Cladding

Irradiation creep compliance is a critical parameter for evaluating the stress evolution of silicon carbide (SiC) components during operation in various reactor concepts. Recent instrumented irradiation creep testing of SiC, performed at low dose in the Halden reactor, showed a creep compliance that is orders of magnitude higher than previous un-instrumented bend relaxation experiments performed in the High Flux Isotope Reactor (HFIR). This discrepancy illustrates the need for additional irradiation creep data for SiC. To this end, a novel irradiation capsule design has been developed to test miniature SiC tensile specimens under loading during irradiation in the HFIR. The experiment design uses the coolant pressure of the HFIR to compress a bellows, which applies the loading on the specimen. Preliminary thermal finite element models were developed to estimate the temperature distribution within the specimen and surrounding capsule components. Similar structural models were developed to evaluate the stress distribution within the specimen. The thermal analyses show that within the gauge section, the specimen temperatures remain within ~10°C of the nominal 300°C design temperature. Similarly, the structural analysis predicts axial stresses within ~10 MPa of the target stress of 100 MPa. These initial analyses show that irradiation creep testing of SiC in the HFIR is feasible and could provide a low-cost, high-throughput vehicle for gathering needed irradiation creep data.

36 MATERIALS SCIENCE↗

A comparison of turbulence closure models for transonic flows about airfoils

Navier-Stokes transonic airfoil calculations using three different turbulence closure models are presented and compared with available experimental data. Two of the models, Cebeci-Smith and Baldwin-Lomax, are equilibrium models in the sense that the turbulent shear stress is assumed to depend only on the local properties of the mean flow. The third model, Johnson and King, is a nonequilibrium model in which an ordinary differential equation is employed to account for the streamwise development of the maximum Reynolds shear stress. An eddy viscosity distribution across the boundary layer is assumed which is functionally dependent on this stress. For attached flows with little inviscid-viscous interaction, little difference in the results with the different models is noted. With stronger interactions and with separation occurring on the airfoils, the nonequilibrium model is shown to perform better.

King, Lyndell S.↗

Thermal stresses in thick laminated composite shells

The paper provides an analytical formulation to investigate the thermomechanical behavior of thick composite shells subjected to a temperature distribution which varies arbitrarily in the radial direction. For illustrative purposes, shells under uniform temperature change are presented. It is found that thermal twist would occur even for symmetric laminated shells. Under uniform temperature rise, results for off-axis graphite/epoxy shells show that extensional-shear coupling can cause tensile radial stress throughout the shell and tensile hoop stress in the inner region. Laminated graphite/epoxy shells can exhibit negative effective thermal expansion coefficients in the longitudinal and transverse directions. Finally, the stacking sequence has a strong influence on the thermal stress distributions.

Yuan, F. G.↗

Chloroplast Membrane Remodeling during Freezing Stress Is Accompanied by Cytoplasmic Acidification Activating SENSITIVE TO FREEZING2

Low temperature is a seasonal abiotic stress that restricts native plant ranges and crop distributions. Two types of lowtemperature stress can be distinguished: chilling and freezing. Much work has been done on the mechanisms by which chilling is sensed, but relatively little is known about how plants sense freezing. Recently, Arabidopsis (Arabidopsis thaliana) SENSITIVE TO FREEZING2 (SFR2) was identified as a protein that responds in a nontranscriptional manner to freezing. Here, we investigate the cellular conditions that allow SFR2 activation. Using a combination of isolated organelle, whole-tissue, and whole-plant assays, we provide evidence that SFR2 is activated by changes in cytosolic pH and Mg 2+ . Manipulation of pH and Mg 2+ in coldacclimated plants is shown to cause changes similar to those of freezing. We conclude that pH and Mg 2+ are perceived as intracellular cues as part of the sensing mechanism for freezing conditions. This evidence provides a specific molecular mechanism to combat freezing.

59 BASIC BIOLOGICAL SCIENCES↗

A Method for Three-Dimensional Deformation Predictions in the Rolling of Steel Strips

In order to achieve a better accuracy-speed balance in the three-dimensional (3-D) deformation calculations of strip rolling, especially for cold rolling of comparatively thin and wide steel strips, a new integrative method is developed. The basic and related mathematic equations and the coupling algorithm are given in detail. To test the approach and prove its effectiveness, four examples are calculated by the proposed method and the models based on the traditional influence function method, taking a six-high strip finishing mill and the rolled piece of a certain specification as research objects. The lateral distributions of front tensile stress that is closely related to the 3-D plastic deformation of the rolled metal and the flatness in the four cases are presented and discussed. The comparison of computational expense and analysis of the results preliminarily confirms that it is workable for this purpose.

36 MATERIALS SCIENCE↗

High elongation achieved by band-like distribution of reinforcements in aluminum matrix composites

Highlights: • The high elongation of composites with high reinforcement content has been achieved by band-like distribution of ABO. • The band-like distribution of ABO could lead to more homogenous strain distribution by scattering the damages. • The cracks played a key role in the strain non-localization process, but have negligible contribution to the tensile strain. • A model of the relationship between the ductility enhancement and the band-like distribution of ABO was established. • The residual stresses induced by band-like distribution of ABO were theoretically calculated and experimentally measured. - Abstract: Ductile aluminum matrix composites reinforced by Al{sub 18}B{sub 4}O{sub 33} whisker (ABO) with band-like distribution (Band-like Aluminum Matrix Composites, BAMCs) were fabricated by powder metallurgy and extrusion followed by annealing. The cracks tend to nucleate in the ABO-rich bands, but the band-like structure induces compressive residual stress then suppresses the crack propagation and improves the strain transferring ability in the BAMCs. The denser and smaller cracks formed in the BAMCs with higher ABO volume fraction during tensile test. These cracks play an important role in the strain non-localization process, but have negligible contribution to the tensile strain.

36 MATERIALS SCIENCE↗

Shape optimization of disc-type flywheels

Techniques were developed for presenting an analytical and graphical means for selecting an optimum flywheel system design, based on system requirements, geometric constraints, and weight limitations. The techniques for creating an analytical solution are formulated from energy and structural principals. The resulting flywheel design relates stress and strain pattern distribution, operating speeds, geometry, and specific energy levels. The design techniques incorporate the lowest stressed flywheel for any particular application and achieve the highest specific energy per unit flywheel weight possible. Stress and strain contour mapping and sectional profile plotting reflect the results of the structural behavior manifested under rotating conditions. This approach toward flywheel design is applicable to any metal flywheel, and permits the selection of the flywheel design to be based solely on the criteria of the system requirements that must be met, those that must be optimized, and those system parameters that may be permitted to vary.

Nizza, R. S.↗

Combined Loads Test Fixture for Thermal-Structural Testing Aerospace Vehicle Panel Concepts

A structural test requirement of the National Aero-Space Plane (NASP) program has resulted in the design, fabrication, and implementation of a combined loads test fixture. Principal requirements for the fixture are testing a 4- by 4-ft hat-stiffened panel with combined axial (either tension or compression) and shear load at temperatures ranging from room temperature to 915 F, keeping the test panel stresses caused by the mechanical loads uniform, and thermal stresses caused by non-uniform panel temperatures minimized. The panel represents the side fuselage skin of an experimental aerospace vehicle, and was produced for the NASP program. A comprehensive mechanical loads test program using the new test fixture has been conducted on this panel from room temperature to 500 F. Measured data have been compared with finite-element analyses predictions, verifying that uniform load distributions were achieved by the fixture. The overall correlation of test data with analysis is excellent. The panel stress distributions and temperature distributions are very uniform and fulfill program requirements. This report provides details of an analytical and experimental validation of the combined loads test fixture. Because of its simple design, this unique test fixture can accommodate panels from a variety of aerospace vehicle designs.

Fields, Roger A.↗