Search NASA⌕ Search

SEARCH · Search NASA

Results for “Small reactors”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,225 records · Page 68

First Data Acquired on the EQ-SANS Diffractometer at the Spallation Neutron Source

The measurement of the conformation of a Generation-8 Polyamidoamine dendrimer is reported as an initial experiment using the Extended Q-range Small Angle Neutron Scattering (EQ-SANS) diffractometer at the Spallation Neutron Source at Oak Ridge National Laboratory (ORNL). The conformation parameters (radius of gyration, thickness of the soft shell etc.) are extracted by model fitting. The results are compared with data collected at the General-Purpose Small Angle Neutron Scattering at the High Flux Isotopic Reactor at ORNL. The comparison shows that the EQ-SANS diffractometer has comparable data statistics and Q resolution with shorter counting time over the measured Q-range.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Assessment of Embrittlement of VHTR Structural Alloys in Impure Helium Environments

The helium coolant in high-temperature reactors inevitably contains low levels of impurities during steady-state operation, primarily consisting of small amounts of H 2 , H 2 O, CH 4 , CO, CO 2 , and N 2 from a variety of sources in the reactor circuit. These impurities are problematic because they can cause significant long-term corrosion in the structural alloys used in the heat exchangers at elevated temperatures. Currently, the primary candidate materials for intermediate heat exchangers are Alloy 617, Haynes 230, Alloy 800H, and Hastelloy X. This project will evaluate the role of impurities in helium coolant on the stress-assisted grain boundary oxidation and creep crack growth in candidate alloys at elevated temperatures.

36 MATERIALS SCIENCE↗

Analysis of an Earthquake-Initiated-Transient in a PBR

One of the Design Basis Accidents (DBA) for a Pebble Bed Reactor has been identified as the “Safe shutdown earthquake with core conduction cooling to passive mode of Reactor Cavity Cooling System.” A new methodology to analyze this particular DBA has been developed at the Idaho National Laboratory (INL). During the seismic event the reactor core experiences the densification of the pebbles, which produce small reactivity insertions due to the effective fuel densification. In addition, a decrease in the active core height results in the relative withdrawal of the control rods, which are assumed to remain stationary during the transient. The methodology relies on the dynamic re-meshing of the core during the transient to capture the local packing fraction changes and their corresponding effects on temperature and reactivity. The core re-meshing methodology is based on the velocity profiles of the pebbles in the core, which were obtained with the INL’s pebble mechanics code PEBBLES. The methodology has been added to the coupled code system CYNOD-THERMIX-KONVEK. The reactor power calculation is further improved with the use of the new advanced TRISO fuel model to better approximate the temperatures in the fuel kernels. During the transient the core is brought back to a safe condition by the strong Doppler feedback from local temperature increases.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Regulatory and Licensing Strategy for Microreactor Technology

With electricity demand on the rise, an increase in the use of nuclear energy is needed in order to meet future energy demands. The use of nuclear energy will not only begin to positively address this demand, but will also mitigate the negative impacts of carbon-induced climate change and provide energy security to the United States. An appropriate option to address the increasing energy demand is the use of advanced reactor systems like microreactors. Microreactors, often referred to as special-purpose reactors or vSMRs, are neutronically simple, factory manufacturable, easily transportable, and designed to produce less than 20 MWt (for classification as Hazard Category 2 per 10 CFR 830, DOE STD 1027). These reactors are decentralized energy sources that have the ability to provide sustainable and affordable power to remote communities and to industrial users, while having self-contained geometry that requires very low maintenance care. In order for microreactors to be approved for operation, they must abide by and successfully complete a rigorous regulatory and licensing process monitored by the Nuclear Regulatory Commission (NRC), the Department of Energy (DOE), or the Department of Defense (DoD). Because microreactors are a relatively new and disruptive technology, there is no clear licensing path for them to follow. Current licensing frameworks are tailored specifically to large, traditional light water reactors (LWRs) that have been developed and understood by the nuclear industry for many years. Unlike LWRs, microreactors have major design differences, specifically in the materials, coolant, reflectors and potential technology applications used. They also have higher in-core operating temperatures, which have the potential to push the materials used past their allowable limits. Because they are much smaller, safety margins, the amount of space required for assembly, and the distances required to meet dose-based regulatory criteria can technically be altered to better fit their new size. The following strategies and recommendations are intended to assure that key licensing issues do not influence the path to microreactor development, demonstration, and commercialization: Nuclear Regulatory Commission • The NRC should address the lack of knowledge and support of risk informed decision-making concepts from staff members and continue to advance and communicate risk initiatives using their Risk Informed Steering Committee • More research should be done into whether or not microreactors, which are small Class 103 facilities, can be licensed using Class 104-type guidance (e.g., NUREG 1537) • The NRC should use frequency-consequence curves to incrementally reduce regulatory uncertainty and risk to facilitate future construction and operation of advanced reactor designs Department of Energy • The DOE should continue to implement their multi-step Phenomena Identification and Ranking Table process in order to help detect and recommend the major design and technology work needed for licensing future reactor systems • The DOE should consider a joint licensing approach with the NRC where microreactors first go through the DOE process, then finish with the NRC process, providing an advantage for both applicants and NRC staff Department of Defense • The DoD should invest in personnel with sufficient expertise, incorporate their military reactors into tactical power systems, and self-regulate using Section 91b of the Atomic Energy Act Transportation • Licensees should convert enriched uranium hexafluoride into metal or oxide at an enrichment facility and then transport them to a fabrication facility • To avoid transportation issues altogether, licensees should consider positioning the enrichment and fabrication facilities on the same site • The DOE should provide their support in developing new shipping packages for safe transport, criticality benchmark data needed to license high-assay low-enriched uranium fuel facilities and transport packages, and provide financial and technical help to the Department of Transportation; and, • The NRC should help transportation efforts by finalizing and developing guidance for implementing 10 CFR 73 and 10 CFR 74 specifically for Category 2 Special Nuclear Material.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Advances toward a transportable antineutrino detector system for reactor monitoring and safeguards

Nuclear reactors have served as the neutrino source for many fundamental physics experiments. The techniques developed by these experiments make it possible to use these very weakly interacting particles for a practical purpose. The large flux of antineutrinos that leaves a reactor carries information about two quantities of interest for safeguards: the reactor power and fissile inventory. Our SNL/LLNL collaboration has demonstrated that such antineutrino based monitoring is feasible using a relatively small cubic meter scale liquid scintillator detector at tens of meters standoff from a commercial Pressurized Water Reactor (PWR). With little or no burden on the plant operator we have been able to remotely and automatically monitor the reactor operational status (on/off), power level, and fuel burnup. The initial detector was deployed in an underground gallery that lies directly under the containment dome of an operating PWR. The gallery is 25 meters from the reactor core center, is rarely accessed by plant personnel, and provides a muon-screening effect of some 20-30 meters of water equivalent earth and concrete overburden. Unfortunately, many reactor facilities do not contain an equivalent underground location. We have therefore attempted to construct a complete detector system which would be capable of operating in an aboveground location and could be transported to a reactor facility with relative ease. A standard 6-meter shipping container was used as our transportable laboratory - containing active and passive shielding components, the antineutrino detector and all electronics, as well as climate control systems. This aboveground system was deployed and tested at the San Onofre Nuclear Generating Station (SONGS) in southern California in 2010 and early 2011. We will first present an overview of the initial demonstrations of our below ground detector. Then we will describe the aboveground system and the technological developments of the two antineutrino detectors that were deployed. Finally, some preliminary results of our aboveground test will be shown. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Assessing the Impact of Large Removable Beryllium Reflector Experiments on HFIR Performance and Safety Metrics

This study investigated the effect of various removable beryllium (RB) experiment configurations on High Flux Isotope Reactor (HFIR) metrics to address increasing interest in these facilities for materials and fuels irradiation research. The RB reflector contains eight large and four small irradiation experiment facilities that offer excellent neutron flux conditions to perform fission and fusion reactor materials and fuels irradiation research. This work aims to outline acceptable RB configurations based on safety, performance, and programmatic metrics. This study assessed experiment effects on reactivity, cycle length, fission rate density distributions, and neutron flux distributions using the Shift, HFIRCON, and SCALE ORIGEN codes. Initial evaluations focused on generic experiment materials including aluminum plugs, stainless steel plugs, molybdenum plugs, and aluminum plugs with gadolinium shields. Subsequent analyses of MiniFuel experiments were performed to evaluate a heterogenous experiment, consisting of a more complex geometry and bearing several materials, and to test the correlations developed with the generic materials on a real experiment. Furthermore, the effects of neutron poison concentrations in the standard beryllium plugs were evaluated. When assuming a reference RB configuration with eight large fresh beryllium plugs, perturbed configurations with three aluminum plugs, one stainless steel plug, one molybdenum plug, one gadolinium-shielded aluminum plug, and one MiniFuel experiment resulted in a cycle length reduction of less than 1.3 days, the current threshold before requiring additional approvals. Configurations with five aluminum plugs, one stainless steel plug, one molybdenum plug, one gadolinium-shielded aluminum plug, and two MiniFuel experiments meet the 1.3 day limit if irradiated beryllium plugs are considered. Fuel element fission rate density distributions remained within safety limits, with maximum local increases under 9%. Neutron flux calculations revealed large thermal flux depressions inside and around the perturbed RB facilities, while epithermal and fast neutron fluxes increased because of reduced neutron moderation by the perturbed materials. These findings provide valuable guidance for optimizing RB configurations to balance safety and performance at HFIR.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Extensive sensitivity study of PWR fuel assay data - 14301

Accurate calculations of the isotopic composition of spent nuclear fuel play a fundamental role in several parts of nuclear energy. An important example is the use of burnup credit in criticality safety analysis, where the results gained from depletion calculations are used to determine the fuel composition in subsequent criticality calculations. The work presented here is a sensitivity study for depletion calculations of high-burnup fuel samples from the Vandellos II PWR that entails an unusually detailed evaluation of assay data. In addition to investigating the impacts of experimental uncertainties on the calculated isotopic composition, the consequences of various modelling approaches are studied to give quantitative estimations of the impact on accuracy. Furthermore, the reactivity of the calculated fuel composition is tracked, because this is the integral characteristic of the irradiated fuel that one is actually interested in for burnup credit applications. While the sensitivity study is performed only for one of the nine experimental samples of the Vandellos II assay data, the lessons learned lead to evaluation models with different levels of model detail for all fuel samples. The results show that the discrepancies between the measured and calculated isotopic compositions are considerably larger than the uncertainties inherent in the measurement and the calculation method would indicate. This is not unexpected, since large discrepancies are a common result of assay data recalculations. However, the unusually extensive sensitivity study performed here allows to exclude some possible sources of error: since the influence of experimental uncertainties like fuel assembly geometry and reactor parameters on the isotopic composition is shown to be small, one valuable conclusion of this study is to focus more on the measurement uncertainties of the chemical assay itself, and the nuclear data that the calculation is based upon. The study also demonstrates that using the reactivity of the depleted fuel as an additional comparison point between measurement and calculation can provide some orientation regarding the importance of the manifold influences on calculation results. Tracking this integral characteristic of the depleted fuel is very helpful in focusing on the actual impact of the depletion calculation uncertainties on criticality safety. (author)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

A portable ion-energy diagnostic for transformative ARPA-E Fusion R&D

The Princeton Plasma Physics Laboratory seeks to develop a diagnostic to measure the energy distribution of ions (IED) in innovative confinement concept devices being investigated under ARAP-E grants. The Princeton Field-Reversed Configuration (PFRC) fusion project aims to develop small, simple, and clean fusion power generators in the 1–10 MW “micro-reactor” class. The PFRC explores a new approach to fusion power-generation design, prioritizing low radioactivity and modular units of MEW-scale power output. The team’s proposed power plant design provides a small footprint for a compact, potentially transportable energy source that is fully deployable and emissions-free. A critical diagnostic to accomplish this mission and to test the theory of ion heating necessary for fusion in PFRC reactors is called a stripping-cell ion-energy analyzer (SC-IEA).

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The benefits of a fast reactor closed fuel cycle in the UK

The work has shown that starting a fast reactor closed fuel cycle in the UK, requires virtually all of Britain's existing and future PWR spent fuel to be reprocessed, in order to obtain the plutonium needed. The existing UK Pu stockpile is sufficient to initially support only a modest SFR 'closed' fleet assuming spent fuel can be reprocessed shortly after discharge (i.e. after two years cooling). For a substantial fast reactor fleet, most Pu will have to originate from reprocessing future spent PWR fuel. Therefore, the maximum fast reactor fleet size will be limited by the preceding PWR fleet size, so scenarios involving fast reactors still require significant quantities of uranium ore indirectly. However, once a fast reactor fuel cycle has been established, the very substantial quantities of uranium tails in the UK would ensure there is sufficient material for several centuries. Both the short and long term impacts on a repository have been considered in this work. Over the short term, the decay heat emanating from the HLW and spent fuel will limit the density of waste within a repository. For scenarios involving fast reactors, the only significant heat bearing actinide content will be present in the final cores, resulting in a 50% overall reduction in decay energy deposited within the repository when compared with an equivalent open fuel cycle. Over the longer term, radiological dose becomes more important. Total radiotoxicity (normalised by electricity generated) is lower for scenarios with Pu recycle after 2000 years. Scenarios involving fast reactors have the lowest radiotoxicity since the quantities of certain actinides (Np, Pu and Am) eventually stabilise. However, total radiotoxicity as a measure of radiological risk does not account for differences in radionuclide mobility once in repository. Radiological dose is dominated by a small number of fission products so is therefore not affected significantly by reactor type or recycling strategy (since the fission product will primarily be a function of nuclear energy generated). However, by reprocessing spent fuel, it is possible to immobilise the fission product in a more suitable waste form that has far more superior in-repository performance. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

TUNABLE IRRADIATION TESTBED

PNNL has developed and continues to develop innovative methods for characterizing irradiated materials from nuclear reactors and particle accelerators for various clients and collaborators around the world. The continued development of these methods, in addition to the ability to perform unique scientific investigations of the effects of radiation on materials could be greatly enhanced with easy access to irradiation facilities. A Tunable Irradiation Testbed with customized targets (a 30 MeV, 1mA cyclotron or similar coupled to a unique target system) is shown to provide a much more flexible and cost-effective source of irradiating particles than a test reactor or isotopic source. The configuration investigated was a single shielded building with multiple beam lines from a small, flexible, high flux irradiation source. Potential applications investigated were the characterization of radiation damage to materials applicable to advanced reactors, fusion reactor, legacy waste, (via neutron spectra tailored to HTGR, molten salt, LWR, LMR, fusion environments); 252Cf replacement; characterization of radiation damage to materials of interest to High Energy Physics to enable the neutrino program; and research into production of short lived isotopes for potential medical and other applications.

Wootan, David W.↗

TUNABLE IRRADIATION TESTBED

PNNL has developed and continues to develop innovative methods for characterizing irradiated materials from nuclear reactors and particle accelerators for various clients and collaborators around the world. The continued development of these methods, in addition to the ability to perform unique scientific investigations of the effects of radiation on materials could be greatly enhanced with easy access to irradiation facilities. A Tunable Irradiation Testbed with customized targets (a 30 MeV, 1mA cyclotron or similar coupled to a unique target system) is shown to provide a much more flexible and cost-effective source of irradiating particles than a test reactor or isotopic source. The configuration investigated was a single shielded building with multiple beam lines from a small, flexible, high flux irradiation source. Potential applications investigated were the characterization of radiation damage to materials applicable to advanced reactors, fusion reactor, legacy waste, (via neutron spectra tailored to HTGR, molten salt, LWR, LMR, fusion environments); 252Cf replacement; characterization of radiation damage to materials of interest to High Energy Physics to enable the neutrino program; and research into production of short lived isotopes for potential medical and other applications.

Wootan, David W.↗

Evaluation of Optical Fiber Bragg Gratings in a Nuclear Reactor

Optical fiber-based sensors are capable of distributed temperature and/or strain measurements with high accuracy and sub-cm spatial resolution. Optical fibers have a small diameter ({approx}100 {mu}m), a small mass (and therefore fast response time), and are fabricated from high temperature-tolerant, radiation-hard materials. These qualities make optical fiber-based instrumentation a promising candidate for in-pile sensing applications, monitoring fuel performance during irradiation in test reactors, or embedding fibers in other commercial reactor components or structures. The Department of Energy and Idaho National Laboratory are restarting the TREAT reactor (Transient Reactor Test facility) and are interested in updating the reactor's instrumentation regarding the analysis of the test fuel. The ability of optical fibers to make distributed temperature measurements coupled with its small footprint makes optical fiber a viable candidate to monitor fuel performance in the TREAT reactor. The work presented in this paper focuses on the radiation hardness of various types of optical fiber Bragg gratings. Previous experiments have shown that the inscription of Bragg gratings into optical fiber can extend the radiation survivability of distributed sensing in optical fibers, and so the goal is to determine which types of Bragg gratings survive the best in a reactor environment.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

The Flow Visualization for the Separation of Air-water Bubbly Two-phase Flow Through a Vertical T-junction

T-junction is a typical structure in many industrial systems such as power plants, chemical process, and hydrocarbon production industries. The separation of two-phase flow passing through T-junction is a common flow phenomenon. There are lots of investigations regarding two-phase flow separation in branching tees and wyes tees. The characteristic of the two-phase flow between the two outlets are always non-uniform, and this kind of fluid status may contribute to the unpredictable damage of downstream facilities. For the nuclear power plants, severe accidents analysis is important especially for Light-Water Reactors (LWR) when Loss of Coolant Accident (LOCA) occurs. The small break of the pipe may cause the coolant become two-phase flow due to the pressure drop. Under certain conditions, the behavior of T-junction is similar to a gas-liquid separator, as a result of the gas enters the side arm and the liquid flows straight along the run arm. The partial separation of gas-liquid mixtures can reduce the load on the main separator, probably leading to smaller units. The study aims to establish complete visual observations for the benchmark of Computational Fluid Dynamics (CFD) model. As a consequence, a vertical T-junction (D = 26 mm) experimental loop was set up for the purpose of elaborating the complex two-phase fluid phenomena. In this experiment, variables were manipulated under highly controlled conditions and a photographic method was proposed to analyze the images of phase separation. Furthermore, the images obtained by camera have been discussed to receive valuable information about the two phase flow behavior around the T-junction.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Manufacture of large grain size of Gd{sub 2}O{sub 3}-UO{sub 2} pellets adding Al(OH){sub 3}

In order to improve the utilization of nuclear fuel, reduce the cost of fuel cycle and improve the economics and flexibility of nuclear power plant in the latest light-water reactors, designers usually adopt the operation strategy of high burnup, long cycle, low leakage, such as using burnable poison fuel in nuclear reactors. So the Gd{sub 2}O{sub 3}-UO{sub 2} pellets is widely used as burnable poison fuel. Pellets is harmful for the running of nuclear reactor if the grain size is too large or too small. Generally, the grain size of Gd{sub 2}O{sub 3}-UO{sub 2} pellets can be called big grain pellets if the grain size is larger than 10 μm. In order to get big grain Gd{sub 2}O{sub 3}-UO{sub 2} pellets, researcher usually adopt grain growth agent to increase the grain size of pellets, this article research the rule of density, pore and grain size of Gd{sub 2}O{sub 3}-UO{sub 2} pellets by adding Al(OH){sub 3}. Al(OH){sub 3} breaks down Al{sub 2}O{sub 3} and H{sub 2}O which can increase the spread of the cation in the lattice, which cause the growth of grain in Gd{sub 2}O{sub 3}-UO{sub 2} pellets. Besides, it also determines the process route of average grain size of more than 10 μm in pellets.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Adjusted Graphite Thermal Scattering Data Applied to Fluoride-Salt-Cooled Reactors

Thermal scattering data is a key component of fission reactor simulation. While most materials can be reasonably modeled with a free gas approximation, the moderators in thermal systems require a more rigorous treatment to sufficiently capture their specific neutron interaction physics. Graphite does not typically feature as a principle moderator in power reactors in service today, but remains an attractive prospect for a number of new reactor concepts currently in development. In comparison to light water, a material nearly ubiquitous in thermal reactors, graphite offers a better neutron economy by way of a small absorption cross section, high thermodynamic stability and can be incorporated into the structure of the core itself. Graphite in its purest form is a crystalline material composed of stacked layers of graphene, a hexagonal planar lattice of carbon atoms. In-plane, each carbon atom is covalently bonded to 3 neighbouring carbon atoms, creating a strong bond, while between planes only a weak van der Waals force exists. Pure graphite has a density of 2.26 g/cm{sup 3}. However, reactor-grade contains a significant amount of carbon binder, leading to a porous bulk medium with randomly oriented micro crystals. Densities of 1.5 - 1.9 g/cm{sup 3} are typical for reactor-grade graphite, corresponding to porosities on the order of 10-30%. This deviation from pure crystalline graphite should be accounted for in the thermal scattering data. When an incident neutron is in or near the thermal region, its de Broglie wavelength is the same order as the molecular bond lengths, leading to elastic scattering. At similar energies, the dynamics of the moderator lattice (in the case of solid moderators) can cause inelastic scattering. For these moderators, special cross sections should be calculated and used in reactor simulations. To generate this thermal scattering data, parameters pertaining to the properties and structure of the material in question are fed into a nuclear data processing code, such as NJOY. Within NJOY is a module called LEAPR which is used to generate the thermal scattering law S(α,β), which is in turn is fed into another module THERMR which is used to generate thermal cross sections that factor in the molecular-scale scattering phenomena. The core of the thermal scattering law is the phonon spectrum ρ(β) which describes the modes of excitation of the material lattice. An investigation into the phonon frequency spectrum was conducted at North Carolina State University (NCSU) for reactor-grade graphite which accounts for porosity. This phonon spectrum was calculated using the ab initio density functional theory (DFT) code VASP. The inelastic cross section calculated using this spectrum was found to have good agreement with relevant experimental data. The resulting spectra differed from the benchmark spectrum produced by Young and Koppel, the same data used in current nuclear data evaluations. The latter uses the lattice dynamics of perfect crystalline graphite with four force constants fitted to the model from thermodynamics data from reactor-grade (porous) graphite, which yields a reasonable approximation to the phonon spectrum of reactor-grade graphite.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Scale-up of Next Generation Nano-Enhanced Composite Materials for Longer Lasting Consumer Goods

The objective for this project was to create an industrial-scale manufacturing operation for Vertically Aligned Carbon Nanotube Forests (VACNTs), which make up N12 Technologies’ (N12) NanoStitch® product, a prepreg additive that makes advanced composites tougher, lighter, and more durable. This was achieved using University of Dayton Research Institute’s (UDRI) 60-inch Nano Adaptive Hybrid Fabric (NAHF-X) reactor system. N12 had a unique and effective nanomaterial-based product that they were manufacturing on small-scale 1-inch wide substrate machines in Boston, MA. UDRI had a large-scale 60-inch wide nanomaterial growth reactor available for scaling up 2nd party products in Dayton, OH. Thanks to the successful cooperation between both parties, this project resulted in the world’s first industrial-scale continuous VACNT film pilot plant in Dayton, OH with an increase in VACNT supply production rate of >10X. This scale up enabled market validation via testing programs and pilot manufacturing operations with a number of customers.

36 MATERIALS SCIENCE↗

Design of a Solar Reactor to Split CO2 Via Isothermal Redox Cycling of Ceria

The design procedure for a 3 kWth prototype solar thermochemical reactor to implement isothermal redox cycling of ceria for CO2 splitting is presented. The reactor uses beds of mm-sized porous ceria particles contained in the annulus of concentric alumina tube assemblies that line the cylindrical wall of a solar cavity receiver. The porous particle beds provide high surface area for the heterogeneous reactions, rapid heat and mass transfer, and low pressure drop. Redox cycling is accomplished by alternating flows of inert sweep gas and CO2 through the bed. The gas flow rates and cycle step durations are selected by scaling the results from small-scale experiments. Thermal and thermo-mechanical models of the reactor and reactive element tubes are developed to predict the steady-state temperature and stress distributions for nominal operating conditions. The simulation results indicate that the target temperature of 1773K will be reached in the prototype reactor and that the Mohr-Coulomb static factor of safety is above two everywhere in the tubes, indicating that thermo-mechanical stresses in the tubes remain acceptably low.

Bader, R↗

Experimental study on a simplified facility of HTGR reactor building response to depressurization accidental scenarios - 18516

The analysis and understanding of air ingress events is an important aspect in the design of The High Temperature Gas Cooled Reactor (HTGR) accident scenarios including Depressurized Loss of Forced Cooling (D-LOFC) events that allow for the possibility of air ingress into the Reactor Pressure Vessel (RPV) as the result of a break in the helium pressure boundary which can ultimately result in oxidation of the fuel elements and other nuclear-grade graphite components. In order to characterize the air ingress into the vented low pressure compartments (VLPC) of NGNP HTGR during hypothetical small break D-LOFC accidents experimentally, a 1/28 down scaled simplified reactor building model was developed. A non-dimensional similarity approach was employed for the scaling analysis of the experimental facility. Two experiments were conducted under similar experimental conditions, with 1.1 kg/h helium injection through the top of the reactor cavity, resulting in oxygen concentrations reaching to steady state within 4 minutes. Differences between the steady state oxygen concentrations results in the steam generator cavity of the two tests with the same experimental conditions were 0.51{+-}0.086% at the top of the steam generator cavity and 0.29{+-}0.11% at the bottom of the steam generator cavity. Difference in the pressure in the reactor between the two experiments were 0.09{+-}0.026 psig. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗