Search NASA⌕ Search

SEARCH · Search NASA

Results for “Structural Effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,225 records · Page 68
All sourcesNASA NTRSDOE OSTI
NASA NTRS2019

Effect of Phenolic Matrix Microcracking on the Structural Response of a 3-D Woven Thermal Protection System

The effect of microcracking in the phenolic matrix of a three-dimensional woven thermal protection system (TPS) and the resulting material stiffness reduction was studied via a comparison of finite element analysis results from a linear analysis and an iterative linear analysis. A TPS is necessary to protect space vehicles from the aerodynamic heating of planetary entry. The Heatshield for Extreme Entry Environment Technology (HEEET) project has developed a TPS for use in high heat-flux and pressure missions. The material is a dual-layer continuous dry weave, which is then infiltrated with a low-density phenolic resin matrix to form a rigid ablator. The phenolic resin matrix does not have structural load transfer requirements, and testing has shown that the phenolic resin can fully satisfy thermal requirements when the matrix contains microcracks. Due to high stresses in the through-the-thickness direction of the material, phenolic microcracks may form in the matrix material, which would result in a reduction of stiffness. An exploratory study was conducted to determine if reduction in material stiffness would change the load paths and/or decrease the structural margins. A comparison was performed between a linear finite element analysis that did not take into account phenolic microcracking and an iterative linear finite element analysis that accounted for propagation of phenolic microcracking. Four subcases using varying assumptions were analyzed and the results indicate that the assumed strength at which the phenolic microcracking propagates was the critical parameter for determining the extent of microcracking in the phenolic matrix. Phenolic microcracking does not have an adverse effect on the structural response of the test article and is not a critical failure.

Langston, Sarah L.↗
DOE OSTI2026

From Pyrolysis Oil to Advanced Biographite Anode: Unravelling Biocoke Structural Evolution and Delayed Coking Effects

Catalytic graphitization of biomass-derived carbon offers a promising route to produce biographite as a sustainable alternative to petroleum-based synthetic graphite for lithium-ion battery (LIB) anodes. This study investigates the physicochemical properties of biocokes produced from pyrolysis oil at carbonization temperatures ranging from 150 degrees C to 500 degrees C. Using an iron (Fe) catalyst, graphitization was performed at 1500 degrees C, significantly lower than the ~3000 degrees C required for conventional synthetic graphite. The effects of introducing an intermediate-temperature hold (400 degrees C-600 degrees C) prior to graphitization were evaluated, simulating a "delayed coking" process to enable the coproduction of sustainable aviation fuels (SAFs). Chemical structure evolution during biocoke formation was analyzed, and proposed mechanisms are presented. Biographites produced via the delayed coking pathway exhibited high crystallinity and excellent electrochemical performance in both half-cell and full-cell LIB configurations. The full cells exhibited an initial discharge capacity close to the theoretical capacity of the NMC622 cathode (175 mAh/g at 4.2 V), and high capacity retention (~88%) after 150 cycles. Notably, the graphitic and electrochemical properties remained stable across the range of intermediate hold temperatures. These findings provide a foundation for optimizing temperature parameters in delayed coking systems to enable scalable, integrated production of biographite and SAFs from pyrolysis oil.

09 BIOMASS FUELS↗
NASA NTRS2000

The Effect of Dilution on the Structure of Microbial Communities

To determine how dilution of microbial communities affects the diversity of the diluted assemblage a series of numerical simulations were conducted that determined the theoretical change in diversity, richness, and evenness of the community with serial dilution. The results of the simulation suggested that the effects are non linear with a high degree of dependence on the initial evenness of the community being diluted. A series of incubation experiments using a range of dilutions of raw sewage as an inoculum into sterile sewage was used for comparison to the simulations. The diluted communities were maintained in batch fed reactors (three day retention time) for nine days. The communities were harvested and examined by conventional plating and by molecular analysis of the whole-community DNA using AFLP and T-RFLP. Additional, CLPP analysis was also applied. The effects on richness predicted by the numerical simulations were confirmed by the analyses used. The diluted communities fell into three groups, a low dilution, intermediate dilution, and high dilution group, which corresponded well with the groupings obtained for community richness in simulation. The grouping demonstrated the non-linear nature of dilution of whole communities. Furthermore, the results implied that the undiluted community consisted of a few dominant types accompanied by a number of rare (low abundance) types as is typical in unevenly distributed communities.

Mills, Aaron L.↗
DOE OSTI2025

AI-Assisted Conceptual Development of a Pre-Geometric Cosmological Model - An Exercise in AI-Assisted Conceptual Framework Generation, Paper II: Local Geometry and Metric Structure

This paper develops the geometric sector of the replication-driven cosmogenesis framework introduced in Paper I. Starting from a pre-geometric spectral substrate and a minimal set of replication axioms, we show how coherent self-replicating units generate a spatial adjacency graph whose continuum limit acquires an effective Riemannian structure. The replication dynamics determines a characteristic correlation length that seeds the local metric, while overlap relations among coherent units produce an isotropic neighborhood geometry with an emergent dimensionality $d_{\rm eff}\simeq 3$ across a broad range of replication factors. As replication slows and causal order stabilizes, a limiting signal speed $c_\ast$ appears, providing the basis for the Lorentzian structure of spacetime without assuming a pre-existing light cone. We derive conditions under which the adjacency graph converges to a smooth three-dimensional manifold, describe the transition from Euclidean to Lorentzian propagation, and identify geometric invariants controlled by the replication parameters. This work establishes the geometric and causal layer of the replication cosmogenesis program, bridging the spectral axioms of Paper I to the cosmological dynamics explored in Paper III.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2019

A novel optical polarization conversion structure designed by multi-layered thin film structures at the wavelength of 10.6 μm

Polarization conversion performance is one of the most important design contents of optical devices. At present, there are many ways to implement polarization conversion. However, they are mostly based on the form of split ring resonator or equivalent plasma, which are not conducive to the miniaturization of electromagnetic devices, particularly in the field of laser applications. In this paper, a novel optical polarization conversion structure has been designed by multi-layered PS/PTFE thin film structures at the wavelength of 10.6 μm based on the equivalent medium theory. Then it was verified that the proposed structure can effectively convert the linear polarized wave to circular polarized wave by the EM full-wave simulation. Compared with the current laser polarization manipulation devices, the proposed novel polarization converter has advantages of ultrathin thickness of structure, simple structure, good light transmission and no electromagnetic loss. Although the structural parameters in this paper are designed for EM wave the wavelength of 10.6 μm, the proposed design idea of the polarization conversion structure is also suitable for the electromagnetic wave at other wavelengths.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2017

On the Faraday Effect in Magnetic Colloids

The propagation of plane-polarized microwave radiation in magnetic colloids with magnetite particles and magnetosensitive emulsions based on such particles is experimentally studied. A magnetic field exerted along the propagation direction leads to the rotation of the polarization plane (Faraday effect) provided that the magnetite concentration is higher than a certain critical level. Specific features of the effect in structured magnetic colloids and magnetic emulsions related to structural changes in the presence of magnetic field are revealed.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS1986

Effects of atmosphere on slewing control of a flexible structure

Air drag forces are introduced into the equations for a slewing control maneuver of a flexible structure to assess the effects of atmosphere on the controller design. Simulated modal parameters and transient responses are compared with experiments in normal atmosphere and in vacuum. Analytical techniques for control laws are examined and verified. Physical insight into the air damping is gained so that results in vacuum can be extrapolated from results in air.

Juang, J.-N.↗
NASA NTRS1981

Study of the photovoltaic effect in thin film barium titanate

The photoelectric effect in structures consisting of metal deposited barium titanate film silicon is described. A radio frequency sputtering technique is used to deposit ferroelectric barium titantate films on silicon and quartz. Film properties are measured and correlated with the photoelectric effect characteristics of the films. It was found that to obtain good quality pin hole free films, it is necessary to reduce the substrate temperature during the last part of the deposition. The switching ability of the device with internal applied voltage is improved when applied with a ferroelectric memory device.

Grannemann, W. W.↗
NASA NTRS1989

Solidification processing of monotectic alloy matrix composites

Directionally solidified aluminum-indium alloys of the monotectic composition were found to form an in situ rod composite which obeys a lambda exp 2 R = constant relation. The experimental data shows good agreement with previously reported results. A theoretical boundary between cellular and dendritic growth conditions was derived and compared with experiments. The unique wetting characteristics of the monotectic alloys can be utilized to tailor the interface structure in metal matrix composites. Metal matrix composites with monotectic and hypermonotectic Al-In matrices were made by pressure infiltration, remelted and directionally solidified to observe the wetting characteristics of the alloys as well as the effect on structure of solidification in the constrained field of the fiber interstices. Models for monotectic growth are modified to take into account solidification in these constrained fields.

Frier, Nancy L.↗
NASA NTRSDate not supplied

Computational Investigation of Oxidative Etch Pitting in FiberForm and Its Impact on Material Properties

Oxidation-driven carbon erosion does not occur uniformly but rather through the development of localized etch pits at active surface sites. These active sites form due to atomic defects on the carbon surface, making them significantly more reactive than the surrounding, non-defective areas. As a result, these sites are the first to react during ablation, leading to their removal. This process creates new defects in neighboring atoms, increasing their reactivity and causing localized carbon removal around these active sites. In this way, the highly reactive defective areas serve as nucleation points for the formation and growth of etch pits, which can have adverse effects on structural integrity of FiberForm. To better understand how these etch pits impact the material properties of carbon fiber microstructures, we have developed a new capability within the direct simulation Monte Carlo (DSMC) framework to capture the etch pit formation process. This capability, integrated into the DSMC code SPARTA (Stochastic Parallel Rarefied-gas Time-accurate Analyzer), models material removal in the presence of active sites, leading to the formation of etch pits. The current work focuses on studying the effects of these etch pits on the material properties of FiberForm, a widely used base material in thermal protection systems (TPS). The microstructure of virgin FiberForm, obtained via X-ray microtomography, is imported into SPARTA to generate the ablated geometries with etch pits. These modified microstructures are then analyzed using the Porous Microstructure Analysis (PuMA) software to compute various material properties, including elasticity, thermal conductivity, and permeability. We investigate the variation of these properties due to the complex surface topology changes caused by etch pit formation. Additionally, we compare the effects of pitting with the conventional model of shrinking fibers, traditionally used to simulate the ablation of carbon structures. Significant differences emerge between the two approaches. Consequently, this physically realistic model of material removal through etch pit formation offers improved accuracy in predicting the degradation of carbon-based TPS during oxidation. It also provides insights into other mechanisms, such as spallation, where chunks of material are removed into the flow due to etch pit growth. Ultimately, this model enhances our understanding of failure modes in these materials during ablation.

PuMA↗
DOE OSTI2021

Effect of PCEs with different structures on hydration and properties of cementitious materials with low water-to-binder ratio

Polycarboxylate ethers (PCEs) with different structures and densities of anchor groups in the backbone were synthesized and characterized. The surface tension of their solutions, their adsorption on cementitious particles and zeta potential of cement-silica fume pastes with PCEs were measured. Their effects on hydration and properties of cement-silica fume paste with low water-to-binder ratio were examined. Results indicated that the adsorption kinetics of theses PCEs on cementitious particles are fitted the pseudo-second-order model. The introduction of long silane chain on PCE decreased its electrostatic adsorption, while PCE was adsorbed onto the surface of particles via both chemical and electrostatic adsorption, when silicon hydroxyl is directly connected to its backbone. In the presence of PCE with higher adsorbed amount, pastes exhibited lower yield stress and higher flowability, and higher strength at 7 d and 28 d. The low plastic viscosity, autogenous and drying shrinkage were related to the low surface tension of PCE solution.

36 MATERIALS SCIENCE↗
NASA NTRS1976

Structure-property relationships in eutectic composites

The preparation of a composite material of eutectic composition directly from the molten state is investigated. The manufacture of eutectic composites by unidirectional solidification is reviewed, and it is shown how two-phase composite structures of given relative volume fraction can be produced with a range of particle sizes. Crystallographic relationships and the thermal stability of interfaces in controlled eutectic structures are examined, the mechanical behavior of aligned eutectic microstructures is discussed, and characteristics of eutectic composites having mechanical properties of engineering significance are evaluated. Specific properties of the Ni-Nb eutectic alloy are reviewed to demonstrate the effect of structure control (through directional solidification) on the mechanical response of a eutectic composite. It is noted that unidirectionally solidified eutectic composites possess highly aligned and thermally stable microstructures and also exhibit excellent combinations of strength and ductility to very high temperature levels.

Hertzberg, R. W.↗
NASA NTRS1993

Probabilistic assessment of composite structures

A general computational simulation methodology for an integrated probabilistic assessment of composite structures is discussed and demonstrated using aircraft fuselage (stiffened composite cylindrical shell) structures with rectangular cutouts. The computational simulation was performed for the probabilistic assessment of the structural behavior including buckling loads, vibration frequencies, global displacements, and local stresses. The scatter in the structural response is simulated based on the inherent uncertainties in the primitive (independent random) variables at the fiber matrix constituent, ply, laminate, and structural scales that describe the composite structures. The effect of uncertainties due to fabrication process variables such as fiber volume ratio, void volume ratio, ply orientation, and ply thickness is also included. The methodology has been embedded in the computer code IPACS (Integrated Probabilistic Assessment of Composite Structures). In addition to the simulated scatter, the IPACS code also calculates the sensitivity of the composite structural behavior to all the primitive variables that influence the structural behavior. This information is useful for assessing reliability and providing guidance for improvement. The results from the probabilistic assessment for the composite structure with rectangular cutouts indicate that the uncertainty in the longitudinal ply stress is mainly caused by the uncertainty in the laminate thickness, and the large overlap of the scatter in the first four buckling loads implies that the buckling mode shape for a specific buckling load can be either of the four modes.

Shiao, Michael E.↗
NASA NTRS2015

Carbon Structure Hazard Control

Carbon composite structures are widely used in virtually all advanced technology industries for a multitude of applications. The high strength-to-weight ratio and resistance to aggressive service environments make them highly desirable. Automotive, aerospace, and petroleum industries extensively use, and will continue to use, this enabling technology. As a result of this broad range of use, field and test personnel are increasingly exposed to hazards associated with these structures. No single published document exists to address the hazards and make recommendations for the hazard controls required for the different exposure possibilities from damaged structures including airborne fibers, fly, and dust. The potential for personnel exposure varies depending on the application or manipulation of the structure. The effect of exposure to carbon hazards is not limited to personnel, protection of electronics and mechanical equipment must be considered as well. The various exposure opportunities defined in this document include pre-manufacturing fly and dust, the cured structure, manufacturing/machining, post-event cleanup, and post-event test and/or evaluation. Hazard control is defined as it is applicable or applied for the specific exposure opportunity. The carbon exposure hazard includes fly, dust, fiber (cured/uncured), and matrix vapor/thermal decomposition products. By using the recommendations in this document, a high level of confidence can be assured for the protection of personnel and equipment.

Yoder, Tommy↗
NASA NTRSDate not supplied

Gimbal Bearing Friction in the SLS Core Stage Thrust Vector Control System

The Space Launch System (SLS) Core Stage Thrust Vector Control (TVC) system is comprised of eight mechanical feedback Shuttle heritage Type III TVC actuators that vector the four Shuttle heritage RS-25 engines about a Shuttle heritage gimbal block/bearing. The MSFC Controls community has long regarded gimbal friction to be a negligible effect on the overall control of gimbaled RS-25 engines. This is corroborated by Space Shuttle test and flight data that does not appear to show degraded effects, nor limit cycling at the end of the shuttle flight. For this reason, friction was not expected to be a driving factor of performance and control of the reused RS-25 engines aboard the SLS. However, after test data showed a large shift in frequency behavior and a highly damped step-response in the time series, there was further investigation into what could have caused this behavior. Heritage friction models used in previous gimbal and ball bearings were evaluated such as Coulomb, Dahl and LuGre, but the single degree of freedom friction models alone were not enough to explain the behavior and shifts seen in the test data. This paper presents the additional findings and modeling efforts regarding friction on the RS-25 engines. Using the Two Actuator Operational Simulation (TAOS), the difference from modeling separate friction degrees of freedom to coupled degrees of freedom was investigated to deduce the effects of one axis’s movement on the other. Next, due to the vibration environment, a modified LuGre model has been proposed that adds an additional term to decrease the friction coefficient at low engine velocity amplitudes. Lastly, the addition of the stiffness in each half of the gimbal bearing has increased modeling fidelity by also adding the effect on the gimbal bearing bending in compliance to both the friction torque on the surface of the gimbal bearing and the actuator force that is forcing the engine in a specified direction. Through these effects, the time and frequency domain behavior seen in test can be characterized accurately.

Friction↗
DOE OSTI2020

Thermodynamics–Structure–Dynamics Correlations and Nonuniversal Effects in the Elastically Collective Activated Hopping Theory of Glass-Forming Liquids

We employ the microscopic Elastically Collective Nonlinear Langevin Equation (ECNLE) theory of activated dynamics in combination with crystal-avoiding simulations to study four inter-related questions for metastable monodisperse hard sphere fluids. The first is how significantly improved integral equation theory structural input (Modified-Verlet (MV) closure) changes the dynamical predictions of ECNLE theory. The main consequence is a modest enhancement of the importance of the collective elastic barrier relative to its local cage contribution, which increases the alpha relaxation time and fragility relative to prior results based on the Percus–Yevick closure. Second, ECNLE-MV theory predictions for the alpha time and self-diffusion constant in the metastable regime are quantitatively compared to our new simulations. The small adjustment of a numerical prefactor that enters the collective elastic barrier leads to quantitative agreement over three decades. Third, using the more accurate MV structural input, ECNLE theory is shown to predict thermodynamics–structure–dynamics “correlations” based on various long and short wavelength scalar properties all related to static two-point collective density fluctuations. The logarithm of the alpha relaxation time scales as a power law with these scalar metrics with an exponent that is significantly lower in the less dense noncooperative activated regime compared to the very dense highly cooperative regime. However, the discovered correlation of activated relaxation with a thermodynamic property (dimensionless compressibility) is not causal in ECNLE theory, but rather reflects a strong connection between the local structural quantities that quantify kinetic constraints in the theory with the amplitude of long wavelength density fluctuations. Fourth, the consequences of chemically specific nonuniversalities associated with the onset condition and relative importance of collective elasticity are studied. In conclusion, the predicted thermodynamics–structure–dynamics correlations are found to be robust, albeit with nontrivial shifts of the onset condition.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Extreme Fast Charging: Effect of Positive Electrode Material on Crosstalk

Extreme fast charging (XFC) is a key requirement for the adoption of battery-based electric vehicles by the transportation sector. However, XFC has been shown to accelerate degradation, causing the capacity, life, and safety of batteries to deteriorate. We tested cells containing five positive electrode chemistries, LFP (olivine structure), LMO (spinel), LCO (layered), NMC811 (layered) and NCA (layered), using fast-charging protocols. After testing, the negative electrodes from cells containing positive electrodes crystallizing with a layered structure were found to have more lithium deposited on their surfaces. Further, those crystallizing with a layered structure also tended to have a larger increase in impedance than those crystallizing with a spinel or olivine structure. Characterization of the negative electrodes by X-ray photoelectron spectroscopy showed that using the concentrations of LiF and Li x PO y F z as metrics, the concentration of LiF in the SEI from the cell with different positive electrodes is LFP > LMO > LCO ~ NMC811 > NCA; and for Li x PO y F z , the order is LMO > LFP > NCA > NMC811 > LCO. Clearly, the positive-electrode material was influencing the amounts of these materials formed.

25 ENERGY STORAGE↗