Results for “Trajectory Tracking” — Page 68

NASA NTRS2000

Mars Global Surveyor Ka-Band Frequency Data Analysis

The Mars Global Surveyor (MGS) spacecraft, launched on November 7, 1996, carries an experimental space-to-ground telecommunications link at Ka-band (32 GHz) along with the primary X-band (8.4 GHz) downlink. The signals are simultaneously transmitted from a 1.5-in diameter parabolic high gain antenna (HGA) on MGS and received by a beam-waveguide (BWG) R&D 34-meter antenna located in NASA's Goldstone Deep Space Network (DSN) complex near Barstow, California. The projected 5-dB link advantage of Ka-band relative to X-band was confirmed in previous reports using measurements of MGS signal strength data acquired during the first two years of the link experiment from December 1996 to December 1998. Analysis of X-band and Ka-band frequency data and difference frequency (f(sub x)-f(sub ka)/3.8) data will be presented here. On board the spacecraft, a low-power sample of the X-band downlink from the transponder is upconverted to 32 GHz, the Ka-band frequency, amplified to I-W using a Solid State Power Amplifier, and radiated from the dual X/Ka HGA. The X-band signal is amplified by one of two 25 W TWTAs. An upconverter first downconverts the 8.42 GHz X-band signal to 8 GHz and then multiplies using a X4 multiplier producing the 32 GHz Ka-band frequency. The frequency source selection is performed by an RF switch which can be commanded to select a VCO (Voltage Controlled Oscillator) or USO (Ultra-Stable Oscillator) reference. The Ka-band frequency can be either coherent with the X-band downlink reference or a hybrid combination of the USO and VCO derived frequencies. The data in this study were chosen such that the Ka-band signal is purely coherent with the X-band signal, that is the downconverter is driven by the same frequency source as the X-band downlink). The ground station used to acquire the data is DSS-13, a 34-meter BWG antenna which incorporates a series of mirrors inside beam waveguide tubes which guide the energy to a subterranean pedestal room, providing a stable environment for the feed and electronics equipment. A dichroic plate is used to reflect the X-band energy and pass the Ka-band energy to another mirror. The RF energy for each band is then focused onto a feed horn and low-noise amplifier package. After amplification and RF/IF downconversion, the IF signals are sent to the Experimental Tone Tracker (ETT), a digital phase-lock-loop receiver, which simultaneously tracks both X-band and Ka-band carrier signals. Once a signal is detected, the ETT outputs estimates of the SNR in a I -Hz bandwidth (Pc/No), baseband phase and frequency of the signals every I -sec. Between December 1996 and December 1998, the Ka-band and X-band signals from MGS were tracked on a regular basis using the ETT. The Ka-band downlink frequencies described here were referenced to the spacecraft's on-board USO which was also the X-band frequency reference (f(sub ka)= 3.8 f(sub x)). The ETT estimates of baseband phase at I -second sampled time tags were converted to sky frequency estimates. Frequency residuals were then generated for each band by removing a model frequency from each observable frequency at each time tag. The model included Doppler and other effects derived from spacecraft trajectory files obtained from the MGS Navigation Team. A simple troposphere correction was applied to the data. In addition to residuals, the USO frequencies emitted by the spacecraft were estimated. For several passes, the USO frequencies were determined from X-band data and from Ka-band data (referred to X-band by dividing by 3.8) and were found to be in good agreement. In addition, X-band USO frequency estimates from MGS Radio Science data acquired from operational DSN stations were available for comparison and were found to agree within the I Hz level. The remaining sub-Hertz differences were attributed to the different models and software algorithms used by MGS Radio Science and KaBLE-11. A summary of the results of a linear fit of the USO frequency versus time (day of year) is presented in Table I for an initial segment of passes.

Morabito, D.↗

NASA NTRS2021

Expected Collision Rates for Tracked Satellites

This analysis estimates collision risks between tracked satellites based on the statistically expected collision rate _Nc and number of collisions Nc, which are closely related to the collision probability Pc. For isolated encounters, Nc equals Pc. For multi-encounter interactions, Nc can exceed Pc and is significantly easier to approximate semi-analytically. Estimating Nc requires integrating the collision rate over time throughout an interaction, with each required _Nc value calculated as a statistical expectation value based on the uncertainty distributions of initial orbital states. The uncertainty distributions are estimated from orbit determination analyses of satellite trajectory measurements. The formulation accounts for the nonlinear orbital motion of the satellites, and derives Nc and _Nc expressions for Monte Carlo simulations as well as semi-analytical approximations for single- and multi-encounter interactions.

Collision Rates↗

NASA NTRS2011

Fuel Burn Estimation Using Real Track Data

A procedure for estimating fuel burned based on actual flight track data, and drag and fuel-flow models is described. The procedure consists of estimating aircraft and wind states, lift, drag and thrust. Fuel-flow for jet aircraft is determined in terms of thrust, true airspeed and altitude as prescribed by the Base of Aircraft Data fuel-flow model. This paper provides a theoretical foundation for computing fuel-flow with most of the information derived from actual flight data. The procedure does not require an explicit model of thrust and calibrated airspeed/Mach profile which are typically needed for trajectory synthesis. To validate the fuel computation method, flight test data provided by the Federal Aviation Administration were processed. Results from this method show that fuel consumed can be estimated within 1% of the actual fuel consumed in the flight test. Next, fuel consumption was estimated with simplified lift and thrust models. Results show negligible difference with respect to the full model without simplifications. An iterative takeoff weight estimation procedure is described for estimating fuel consumption, when takeoff weight is unavailable, and for establishing fuel consumption uncertainty bounds. Finally, the suitability of using radar-based position information for fuel estimation is examined. It is shown that fuel usage could be estimated within 5.4% of the actual value using positions reported in the Airline Situation Display to Industry data with simplified models and iterative takeoff weight computation.

Chatterji, Gano B.↗

DOE OSTI2018

Clean Energy Trust Challenge

Over the past three years, Clean Energy Trust (CET) supported student education and early-stage entrepreneurship in the clean energy sector by managing and effectively executing the Cleantech University Prize (Cleantech UP) initiative. CET has a long track record running these competition-style events; CET built on its past successes with the National Clean Energy Business Plan Competition (NCEBPC) and the Clean Energy Trust Challenge (the Challenge) - CET's annual business plan competition and summit event - to excel during this initiative. CET's goals with this Cleantech UP program were to enhance student engagement and participation across colleges and universities in the Midwest region. This broad objective was outlined by increasing the number of applicants, the number and geographic footprint of universities and colleges actively engaged and, most importantly, the trajectory for the student businesses that participate in our programs.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

NASA NTRS1976

Ionospheric Refraction Corrections in the GTDS for Satellite-To-Satellite Tracking Data

In satellite-to-satellite tracking (SST) geographic as well as diurnal ionospheric effects must be contended with, for the line of sight between satellites can cross a day-night interface or lie within the equatorial ionosphere. These various effects were examined and a method of computing ionospheric refraction corrections to range and range rate measurements with sufficient accuracy were devised to be used in orbit determinations. The Bent Ionospheric Model is used for SST refraction corrections. Making use of this model a method of computing corrections through large ionospheric gradients was devised and implemented into the Goddard Trajectory Determination System. The various considerations taken in designing and implementing this SST refraction correction algorithm are reported.

Nesterczuk, G.↗

DOE OSTI2018

Quaternary tephra from the Valles caldera in the volcanic field of the Jemez Mountains of New Mexico identified in western Canada

A fine-grained, up to 3-m-thick tephra bed in southwestern Saskatchewan, herein named Duncairn tephra (Dt), is derived from an early Pleistocene eruption in the Jemez Mountains volcanic field of New Mexico, requiring a trajectory of northward tephra dispersal of ~1500 km. An unusually low CaO content in its glass shards denies a source in the closer Yellowstone and Heise volcanic fields, whereas a Pleistocene tephra bed (LSMt) in the La Sal Mountains of Utah has a very similar glass chemistry to that of the Dt, supporting a more southerly source. Comprehensive characterization of these two distal tephra beds along with samples collected near the Valles caldera in New Mexico, including grain size, mineral assemblage, major- and trace-element composition of glass and minerals, paleomagnetism, and fission-track dating, justify this correlation. Two glass populations each exist in the Dt and LSMt. The proximal correlative of Dt1 is the plinian Tsankawi Pumice and co-ignimbritic ash of the first ignimbrite (Qbt1g) of the 1.24 Ma Tshirege Member of the Bandelier Tuff. Finally, the correlative of Dt2 and LSMt is the co-ignimbritic ash of Qbt2. Mixing of Dt1 and Dt2 probably occurred during northward transport in a jet stream.

58 GEOSCIENCES↗

NASA NTRS1979

Flight test of a VTOL digital autoland system along complex trajectories

The objective of this research is the development and flight test of a digital multi-rate VTOL autoland system. This autoland system provided the NASA/Army Fly-by-Wire CH-47 helicopter with an automatic 4-D trajectory following and landing capability. Flight tests were conducted along complex trajectories with descending, turning, and decelerating segments. The flight software consists of a trajectory generator and guidance algorithm operating at two iterations per second and a set of sensor filters and an advanced controller operating at 10 iterations per second. This low iteration rate digital controller has a proportional-integral structure that provides an autotrim function. The control gains, scheduled as a function of flight condition, are updated every two seconds. All flight software, except input/output routines, are coded in FORTRAN using floating point arithmetic and are exercised in a ROLM 1664 flight computer. The flight software, the ground and flight hardware, the autoland system's position tracking performance, and the controller's velocity and heading tracking performance are presented.

Downing, D. R.↗

NASA NTRS1985

Geophysical interpretation of Venus gravity data

The investigation of the subsurface mass distribution of Venus through the analysis of the data from Pioneer Venus Orbiter (PVO) is presented. The Doppler tracking data was used to map the gravitational potential, which was compared to the topographic data from the PVO radar (ORAD). In order to obtain an unbiased comparison, the topography obtained from the PVO-ORAD was filtered to introduce distortions which are the same as those of our gravity models. The last major software package that was required in order to determine the spectral admittance Z (lambda) was used. This package solves the forward problem: given the topography and its density, and assuming no compensation, find the resulting spacecraft acceleration along a given nominal trajectory. The filtered topography is obtained by processing these accelerations in the same way (i.e., with the same geophysical inverter) as the Doppler-rate data that we use to estimate the gravity maps.

Reasenberg, R. D.↗

NASA NTRS1993

TOPEX/Poseidon precision orbit determination production and expert system

TOPEX/Poseidon (T/P) is a joint mission between NASA and the Centre National d'Etudes Spatiales (CNES), the French Space Agency. The TOPEX/Poseidon Precision Orbit Determination Production System (PODPS) was developed at Goddard Space Flight Center (NASA/GSFC) to produce the absolute orbital reference required to support the fundamental ocean science goals of this satellite altimeter mission within NASA. The orbital trajectory for T/P is required to have a RMS accuracy of 13 centimeters in its radial component. This requirement is based on the effective use of the satellite altimetry for the isolation of absolute long-wavelength ocean topography important for monitoring global changes in the ocean circulation system. This orbit modeling requirement is at an unprecedented accuracy level for this type of satellite. In order to routinely produce and evaluate these orbits, GSFC has developed a production and supporting expert system. The PODPS is a menu driven system allowing routine importation and processing of tracking data for orbit determination, and an evaluation of the quality of the orbit so produced through a progressive series of tests. Phase 1 of the expert system grades the orbit and displays test results. Later phases undergoing implementation, will prescribe corrective actions when unsatisfactory results are seen. This paper describes the design and implementation of this orbit determination production system and the basis for its orbit accuracy assessment within the expert system.

Putney, Barbara↗

NASA NTRSDate not supplied

Assimilation of SMAP Observations Over Land Improves the Simulation and Prediction of Tropical Cyclone Idai

This work is focused on the role of soil moisture in the prediction of tropical cyclones (TCs) approaching land and after landfall. Soil moisture conditions can impact the circulation and structure of an existing tropical cyclone (TC) when part or all of the circulation is over land. For example, dry land surface conditions may lead to faster dissipation of a TC over land (often associated with changes in precipitation structure), whereas very wet conditions may help sustain or in rare cases re-intensify a TC. Moreover, the presence of strong soil moisture gradients may affect the symmetry and development of the TC circulation leading to changes in its over-land track. While the link between soil moisture conditions and TC evolution in proximity to land is relatively well understood in theory, applications of these findings in the context of numerical weather prediction (NWP) have been limited. Here we present a case study that explores the potential of improving TC predictions through an improved soil moisture initialization in an NWP framework. Specifically, we examine the impact of assimilating observations from the NASA Soil Moisture Active Passive (SMAP) mission into the NASA Goddard Earth Observing System (GEOS) global weather model on the prediction of South-West Indian Ocean TC Idai (2019). SMAP provides accurate L-band (1.4 GHz) brightness temperatures (Tb) observations that are sensitive to soil moisture globally and at high revisit times of 2-3 days. It has previously been shown that the assimilation of SMAP Tb observations significantly improves modeled land surface states. Thus, it is expected that SMAP can be used to constrain land surface initial conditions and potentially benefit TC forecasts. Here we present two sets of retrospective forecasts of TC Idai that are compared in an Observing System Experiment framework at ¼ degree resolution: (i) forecasts initialized from an analysis that is comparable to the GEOS operational analysis (without SMAP Tb assimilation) and (ii) forecasts initialized from an analysis that additionally assimilates SMAP brightness temperature observations over land using a weakly-coupled land analysis. We find that the assimilation of SMAP meaningfully improves the representation of TC Idai’s structure as well as the prediction of its intensity and track. The analyzed TC size, as measured by the wind speed radius, is improved by up to 18% in the analysis with SMAP assimilation relative to the control run. The forecast intensity error, measured against the observed intensity, is reduced by up to 23%. At the 1/4-degree resolution used here, GEOS unavoidably under-estimates TC intensity and over-estimates TC size. The SMAP assimilation therefore corrects the model in the right direction, leading to a storm that is more energetic and more compact. Furthermore, we find that the along-track forecast error is reduced by up to 34%, indicating a more accurate propagation speed, which is consistent with the fact that TC speed over land is strongly affected by surface processes. The impact of SMAP assimilation on the forecast cross-track error is neutral. Across the TC forecast skill metrics used here, the improvements from SMAP DA are largest at lead times of 36 to 72 hours, suggesting that the predictability of forecasts at shorter lead times may be dominated by short-term convective processes, while the land and its longer memory gains in importance as a source of predictability on a 2-3 day timescale. We further investigated the underlying mechanisms leading to the skill improvements from SMAP data assimilation by isolating the land areas that directly influence TC Idai using a back trajectory analysis. We find that the assimilation of SMAP leads to wetter soil moisture conditions that cause an increased latent heat flux, which ultimately results in TC analyzed representation that has higher column-integrated total moisture content and total energy compared to the analysis in the control run without SMAP assimilation. Overall, the results highlight that the assimilation of SMAP observations into a global numerical weather prediction model can lead to pronounced improvements of TC predictions. This is a crucial step towards a better mitigation of the socio-economic impact of landfalling TCs and thus safeguarding human lives. Finally, our study presents an event-based approach that assesses the impact of land data assimilation for a particular weather event rather than by globally averaging differences in skill. We argue that global skill assessments – while necessary – can mute the impact of land data assimilation, because the land’s influence on the atmosphere is constrained to certain locations and certain times. Instead, the event-based approach better highlights the true potential of land data assimilation in the context of NWP, especially for extreme events when accurate predictions are critical.

Jana Kolassa↗

NASA NTRSDate not supplied

Assimilation of SMAP Observations Over Land Improves the Simulation and Prediction of Tropical Cyclone Idai

This work is focused on the role of soil moisture in the prediction of tropical cyclones (TCs) approaching land and after landfall. Soil moisture conditions can impact the circulation and structure of an existing tropical cyclone (TC) when part or all of the circulation is over land. For example, dry land surface conditions may lead to faster dissipation of a TC over land (often associated with changes in precipitation structure), whereas very wet conditions may help sustain or in rare cases re-intensify a TC. Moreover, the presence of strong soil moisture gradients may affect the symmetry and development of the TC circulation leading to changes in its over-land track. While the link between soil moisture conditions and TC evolution in proximity to land is relatively well understood in theory, applications of these findings in the context of numerical weather prediction (NWP) have been limited. Here we present a case study that explores the potential of improving TC predictions through an improved soil moisture initialization in an NWP framework. Specifically, we examine the impact of assimilating observations from the NASA Soil Moisture Active Passive (SMAP) mission into the NASA Goddard Earth Observing System (GEOS) global weather model on the prediction of South-West Indian Ocean TC Idai (2019). SMAP provides accurate L-band (1.4 GHz) brightness temperatures (Tb) observations that are sensitive to soil moisture globally and at high revisit times of 2-3 days. It has previously been shown that the assimilation of SMAP Tb observations significantly improves modeled land surface states. Thus, it is expected that SMAP can be used to constrain land surface initial conditions and potentially benefit TC forecasts. Here we present two sets of retrospective forecasts of TC Idai that are compared in an Observing System Experiment framework at ¼ degree resolution: (i) forecasts initialized from an analysis that is comparable to the GEOS operational analysis (without SMAP Tb assimilation) and (ii) forecasts initialized from an analysis that additionally assimilates SMAP brightness temperature observations over land using a weakly-coupled land analysis. We find that the assimilation of SMAP meaningfully improves the representation of TC Idai’s structure as well as the prediction of its intensity and track. The analyzed TC size, as measured by the wind speed radius, is improved by up to 18% in the analysis with SMAP assimilation relative to the control run. The forecast intensity error, measured against the observed intensity, is reduced by up to 23%. At the 1/4-degree resolution used here, GEOS unavoidably under-estimates TC intensity and over-estimates TC size. The SMAP assimilation therefore corrects the model in the right direction, leading to a storm that is more energetic and more compact. Furthermore, we find that the along-track forecast error is reduced by up to 34%, indicating a more accurate propagation speed, which is consistent with the fact that TC speed over land is strongly affected by surface processes. The impact of SMAP assimilation on the forecast cross-track error is neutral. Across the TC forecast skill metrics used here, the improvements from SMAP DA are largest at lead times of 36 to 72 hours, suggesting that the predictability of forecasts at shorter lead times may be dominated by short-term convective processes, while the land and its longer memory gains in importance as a source of predictability on a 2-3 day timescale. We further investigated the underlying mechanisms leading to the skill improvements from SMAP data assimilation by isolating the land areas that directly influence TC Idai using a back trajectory analysis. We find that the assimilation of SMAP leads to wetter soil moisture conditions that cause an increased latent heat flux, which ultimately results in TC analyzed representation that has higher column-integrated total moisture content and total energy compared to the analysis in the control run without SMAP assimilation. Overall, the results highlight that the assimilation of SMAP observations into a global numerical weather prediction model can lead to pronounced improvements of TC predictions. This is a crucial step towards a better mitigation of the socio-economic impact of landfalling TCs and thus safeguarding human lives. Finally, our study presents an event-based approach that assesses the impact of land data assimilation for a particular weather event rather than by globally averaging differences in skill. We argue that global skill assessments – while necessary – can mute the impact of land data assimilation, because the land’s influence on the atmosphere is constrained to certain locations and certain times. Instead, the event-based approach better highlights the true potential of land data assimilation in the context of NWP, especially for extreme events when accurate predictions are critical.

Jana Kolassa↗

DOE OSTI2021

Tomographic X-ray particle tracking velocimetry

We investigate the feasibility of in-laboratory tomographic X-ray particle tracking velocimetry (TXPTV) and consider creeping flows with nearly density matched flow tracers. Specifically, in these proof-of-concept experiments we examined a Poiseuille flow, flow through porous media and a multiphase flow with a Taylor bubble. For a full 360° computed tomography (CT) scan we show that the specially selected 60 micron tracer particles could be imaged in less than 3 seconds with a signal-to-noise ratio between the tracers and the fluid of 2.5, sufficient to achieve proper volumetric segmentation at each time step. In the pipe flow, continuous Lagrangian particle trajectories were obtained, after which all the standard techniques used for PTV or PIV (taken at visible wave lengths) could also be employed for TXPTV data. And, with TXPTV we can examine flows inaccessible with visible wave lengths due to opaque media or numerous refractive interfaces. In the case of opaque porous media we were able to observe material accumulation and pore clogging, and for flow with Taylor bubble we can trace the particles and hence obtain velocities in the liquid film between the wall and bubble, with thickness of liquid film itself also simultaneously obtained from the volumetric reconstruction after segmentation. While improvements in scan speed are anticipated due to continuing improvements in CT system components, we show that for the flows examined even the presently available CT systems could yield quantitative flow data with the primary limitation being the quality of available flow tracers.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

NASA NTRS1996

Numerical Investigation of Two-Phase Flows With Charged Droplets in Electrostatic Field

A numerical method to solve two-phase turbulent flows with charged droplets in an electrostatic field is presented. The ensemble-averaged Navier-Stokes equations and the electrostatic potential equation are solved using a finite volume method. The transitional turbulence field is described using multiple-time-scale turbulence equations. The equations of motion of droplets are solved using a Lagrangian particle tracking scheme, and the inter-phase momentum exchange is described by the Particle-In-Cell scheme. The electrostatic force caused by an applied electrical potential is calculated using the electrostatic field obtained by solving a Laplacian equation and the force exerted by charged droplets is calculated using the Coulombic force equation. The method is applied to solve electro-hydrodynamic sprays. The calculated droplet velocity distributions for droplet dispersions occurring in a stagnant surrounding are in good agreement with the measured data. For droplet dispersions occurring in a two-phase flow, the droplet trajectories are influenced by aerodynamic forces, the Coulombic force, and the applied electrostatic potential field.

Kim, Sang-Wook↗

NASA NTRS1983

The movement and decay of ice edge bands in the winter Bering Sea

A study of the movement and decay of ice bands in the Bering Sea carried out in March 1981 is described. A pair of radio transponders mounted on ice floes within a band was tracked and the band motion was compared with that of a satellite-tracked buoy deployed in the ice interior. The results show that the bands moved away from the interior pack ice at a speed 30 percent greater than that of the interior ice, that the cause of this band acceleration was very likely the wind-wave radiation stress on the upwind side of the band, and that as the bands moved into warmer water, they decayed both by wind-wave erosion of the upwind edge and by bottom melting. The working of the buoys and the method of deployment are described, as are the band shape, trajectory, and decay. By a calculation of the steady state stress balance on the band, it is shown that the radiation stress can account for the velocity increase of the band relative to the ice interior.

Martin, S.↗

NASA NTRS1993

Application of a Two Camera Video Imaging System to Three-Dimensional Vortex Tracking in the 80- by 120-Foot Wind Tunnel

A description is presented of two enhancements for a two-camera, video imaging system that increase the accuracy and efficiency of the system when applied to the determination of three-dimensional locations of points along a continuous line. These enhancements increase the utility of the system when extracting quantitative data from surface and off-body flow visualizations. The first enhancement utilizes epipolar geometry to resolve the stereo "correspondence" problem. This is the problem of determining, unambiguously, corresponding points in the stereo images of objects that do not have visible reference points. The second enhancement, is a method to automatically identify and trace the core of a vortex in a digital image. This is accomplished by means of an adaptive template matching algorithm. The system was used to determine the trajectory of a vortex generated by the Leading-Edge eXtension (LEX) of a full-scale F/A-18 aircraft tested in the NASA Ames 80- by 120-Foot Wind Tunnel. The system accuracy for resolving the vortex trajectories is estimated to be +/-2 inches over distance of 60 feet. Stereo images of some of the vortex trajectories are presented. The system was also used to determine the point where the LEX vortex "bursts". The vortex burst point locations are compared with those measured in small-scale tests and in flight and found to be in good agreement.

Meyn, Larry A.↗

NASA NTRS1992

A gravity field comparison and analysis to support Magellan navigation

The orbit characteristics of Magellan are such that the spacecraft is extremely sensitive to gravity perturbations; therefore, the precision orbit determination required to construct the radar images is very dependent on accurate gravitational field modeling. As such, a comparison and analysis is presented of four global harmonic Venusian gravity fields generated by two-way S-band Doppler tracking data from the Pioneer Venus Orbiter in order to support the precise navigational requirements of the Magellan spacecraft. The four fields are: (1) one of degree and order 10 (a 10 x 10) from Mottinger et al. (1985), (2) an 18 x 18 from Bills et al. (1987), (3) a 21 x 21 from McNamee et al. (1990), and (4) a 36 x 36 from Smith et al. (1991). Least-square fits are done with each gravity field on 36 8-rev Magellan X-band data arcs, spaced at 10-deg longitude intervals, completely encircling Venus. Trajectory differences are also performed for two distinct cases, one where the gravity field modeling coincides, and the other where the gravity fields are very different. Although all of the above fields are found to model Venus gravity fairly well, the results show that there is still much room for improvement in Venus gravity modeling.

Kronschnabl, G. R.↗

NASA NTRS2005

Deep Space Network Capabilities for Receiving Weak Probe Signals

Planetary probes can encounter mission scenarios where communication is not favorable during critical maneuvers or emergencies. Launch, initial acquisition, landing, trajectory corrections, safing. Communication challenges due to sub-optimum antenna pointing or transmitted power, amplitude/frequency dynamics, etc. Prevent lock-up on signal and extraction of telemetry. Examples: loss of Mars Observer, nutation of Ulysses, Galileo antenna, Mars Pathfinder and Mars Exploration Rovers Entry, Descent, and Landing, and the Cassini Saturn Orbit Insertion. A Deep Space Network capability to handle such cases has been used successfully to receive signals to characterize the scenario. This paper will describe the capability and highlight the cases of the critical communications for the Mars rovers and Saturn Orbit Insertion and preparation radio tracking of the Huygens probe at (non-DSN) radio telescopes.

Asmar, Sami↗

DOE OSTI2018

Life cycle assessment of an energy-economy nexus: The case of Israel and South Korea

Israel and South Korea have both achieved rapid economic growth since their post-war establishment, and among the common challenges that the two countries have faced is a conspicuous lack of domestic oil supplies. Although this chronic energy scarcity has not impeded the economic trajectory of either country, it has influenced their industrial structures in strikingly different ways – with Korea nevertheless developing a vast energy-intensive manufacturing sector, while Israel has largely relied on its service sector to support a growing consumer society. While different in industrial structure, however, the two economies have been connected by intensive trade relations, meaning that energy is consumed in one country for the production of goods used in the other. In order to examine the economic and environmental implications of the two economies' structural divergence and bilateral trade relations, we use economic input-output analysis to track the life cycle (LC) energy consumption of passenger cars – a product which has significant environmental impact due to energy consumption in both its production and use stages – which were manufactured in Korea and exported to Israel during the period of 1997–2011. Our findings show that while most of the LC energy consumption of the vehicles occurs in Israel where the vehicle operation takes place, this does not mean that Israel's “avoided energy” by importing the Korean cars is insignificant. The embodied energy of vehicles traded in 2011 reached 3179 TJ, exceeding the amount of energy used by Israel's entire on-site building construction sector over the same period. If the Israeli economy had hypothetically developed its own auto manufacturing industry including secondary suppliers to meet domestic demand as well as exports – as was done in Korea – the energy consumption in those industries would be equivalent to about half of the current energy use by Israel's entire industrial sector.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗