Search NASA⌕ Search

SEARCH · Search NASA

Results for “circuit optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,225 records · Page 68

Surface and bulk effects of K in highly efficient Cu 1-x K x InSe 2 solar cells

To advance knowledge of the beneficial effects of K in Cu(In,Ga)(Se,S) 2 (CIGS) photovoltaic (PV) absorbers, recent Cu-K-In-Se phase growth studies have been extended to PV performance. First, the effect of distributing K throughout bulk Cu 1-x K x InSe 2 absorbers at low K/(K+Cu) compositions (0 = x = 0.30) was studied. Efficiency, open-circuit voltage (VOC), and fill factor (FF) were greatly enhanced for x ~ 0.07, resulting in an officially-measured 15.0%-efficient solar cell, matching the world record CuInSe 2 efficiency. The improvements were a result of reduced interface and bulk recombination, relative to CuInSe 2 (x ~ 0). However, higher x compositions had reduced efficiency, short-circuit current density (J SC ), and FF due to greatly increased interface recombination, relative to the x ~ 0 baseline. Next, the effect of confining K at the absorber/buffer interface at high K/(K+Cu) compositions (0.30 = x = 0.92) was researched. Previous work showed that these surface layer growth conditions produced CuInSe 2 with a large phase fraction of KInSe 2 . After optimization (75 nm surface layer with x ~ 0.41), these KInSe 2 surface samples exhibited increased efficiency (officially 14.9%), VOC, and FF as a result of decreased interface recombination. The KInSe 2 surfaces had features similar to previous reports for KF post-deposition treatments (PDTs) used in world record CIGS solar cells - taken as indirect evidence that KInSe 2 can form during these PDTs. Both the bulk and surface growth processes greatly reduced interface recombination. However, the KInSe 2 surface had higher K levels near the surface, greater lifetimes, and increased inversion near the buffer interface, relative to the champion bulk Cu 1-x K x InSe 2 absorber. These characteristics demonstrate that K may benefit PV performance by different mechanisms at the surface and in the absorber bulk.

14 SOLAR ENERGY↗

Development of Selective Covalent Janus Kinase 3 Inhibitors

The Janus kinases (JAKs) and their downstream effectors, signal transducer and activator of transcription proteins (STATs), form a critical immune cell signaling circuit, which is of fundamental importance in innate immunity, inflammation, and hematopoiesis, and dysregulation is frequently observed in immune disease and cancer. The high degree of structural conservation of the JAK ATP binding pockets has posed a considerable challenge to medicinal chemists seeking to develop highly selective inhibitors as pharmacological probes and as clinical drugs. Here we report the discovery and optimization of 2,4-substituted pyrimidines as covalent JAK3 inhibitors that exploit a unique cysteine (Cys909) residue in JAK3. Investigation of structure–activity relationship (SAR) utilizing biochemical and transformed Ba/F3 cellular assays resulted in identification of potent and selective inhibitors such as compounds 9 and 45. A 2.9 Å cocrystal structure of JAK3 in complex with 9 confirms the covalent interaction. Compound 9 exhibited decent pharmacokinetic properties and is suitable for use in vivo. As a result, these inhibitors provide a set of useful tools to pharmacologically interrogate JAK3-dependent biology.

59 BASIC BIOLOGICAL SCIENCES↗

Design and synthesis of chlorinated benzothiadiazole-based polymers for efficient solar energy conversion

Here, chlorinated benzothiadiazide based polymers with multiple chlorine atoms has been designed and synthesized for polymer solar cells with enhanced open circuit voltage up to 0.85 V. The chlorine substitution is found to significantly adjust the band gap of the polymers, and change polymer’s orientation from random morphology of chlorine free PBT4T-2OD, to mixed face-on packing of one chlorine substituted PCBT4T-2OD, and finally to edge-on of two chlorine substituted PCCBT4T-2OD. The optimized chlorinated polymer, PCBT4T-2OD with only one chlorine atom substituted on BT moiety, has been founded to achieve the highest power conversion efficiency up to 8.20% with PC 71 BM, which is about 68% higher than that of its non-chlorine analogues.

14 SOLAR ENERGY↗

Universal control of a six-qubit quantum processor in silicon

Future quantum computers capable of solving relevant problems will require a large number of qubits that can be operated reliably. However, the requirements of having a large qubit count and operating with high fidelity are typically conflicting. Spins in semiconductor quantum dots show long-term promise but demonstrations so far use between one and four qubits and typically optimize the fidelity of either single- or two-qubit operations, or initialization and readout. Here, we increase the number of qubits and simultaneously achieve respectable fidelities for universal operation, state preparation and measurement. We design, fabricate and operate a six-qubit processor with a focus on careful Hamiltonian engineering, on a high level of abstraction to program the quantum circuits, and on efficient background calibration, all of which are essential to achieve high fidelities on this extended system. State preparation combines initialization by measurement and real-time feedback with quantum-non-demolition measurements. These advances will enable testing of increasingly meaningful quantum protocols and constitute a major stepping stone towards large-scale quantum computers.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Thermodynamic stability of xenon-doped liquid argon detectors

Liquid argon detectors are employed in a wide variety of nuclear and particle physics experiments. The addition of small quantities of xenon to argon modifies its scintillation, ionization, and electroluminescence properties and can improve its performance as a detection medium. However, a liquid argon-xenon mixture can develop instabilities, especially in systems that require phase transitions or that utilize high xenon concentrations. In this work, we analyze the causes of these instabilities and describe a small (liter-scale) apparatus with a unique cryogenic circuit specifically designed to handle argon-xenon mixtures. The system is capable of condensing argon gas mixed with $\mathscr{O}$ (1%) xenon by volume and maintains a stable liquid mixture near the xenon saturation limit while actively circulating it in the gas phase. We also demonstrate control over instabilities that develop when the detector condition is allowed to deviate from optimized settings. This progress enables future liquid argon detectors to benefit from the effects of high concentrations of xenon doping, such as more efficient detection of low-energy ionization signals. In conclusion, this work also develops tools to study and mitigate instabilities in large argon detectors that use low concentration xenon doping.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Virtual Metering for Monitoring Building Energy Consumption

The United States Department of Energy (DOE) has standard metering requirements of commercial buildings for optimizing energy performance. The guiding principles are to continuously track and optimize energy performance and install building-level meters for electricity, natural gas, and steam. Some buildings at Los Alamos National Laboratory (LANL) have physical submeters monitoring their energy consumption, but these meters have proven to be unreliable. And, in most cases, replacing them has proven to be a slow process. Installing new submeters also requires a temporary lockout of the circuit on which they are being installed. Many buildings at LANL contain laboratories with ongoing experiments or data centers, which makes an equipment power outage nearly impossible to plan. This inability to plan power outages results in long-term submeter failures. Although most submeters are eventually replaced, failures lead to missing consumption data for some unpredictable, extended time. A building automation system (BAS) is a system that provides control and monitoring on a building to maintain the operational performance of the building and occupancy comfort. Many buildings at LANL currently have a BAS, and all new renovations and installs will include installing a BAS if one does not already exist. The intended purpose for a BAS is primarily to monitor the health and efficiency of a building; however, it is also possible to calculate equipment power and energy consumption using BAS information. This project aims to use virtual meters to monitor building energy consumption as a cost-effective and minimally labor-intensive alternative to installing physical submeters. The fault detection and diagnostics tool, SkySpark, provides a centralized database for all the data from the various BAS that are active at LANL. This data includes the information that is needed to create virtual meters for heating, ventilating, and air conditioning (HVAC) systems in most buildings, including heating and cooling loads. 9 This report begins with a detailed summary of the project, including the reasoning, procedure, and results. The specific processes of creating the various virtual meters are then identified. Then the limitations are discussed. And, lastly, the results and future potential are presented.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Power management and control for space systems

Power management and control technology for the large, high-power spacecraft of the 1980's is discussed. Systems weight optimization that indicate a need for higher bus voltages are shown. Environmental interactions that are practical limits for the maximum potential on exposed surfaces are shown. A dual-voltage system is proposed that would provide the weight savings of a high-voltage distribution system and take into account the potential environmental interactions. The technology development of new components and circuits is also discussed.

Finke, R. C.↗

Telerobotic control of a mobile coordinated robotic server, executive summary

This interim report continues with the research effort on advanced adaptive controls for space robotics systems. In particular, previous results developed by the principle investigator and his research team centered around fuzzy logic control (FLC) in which the lack of knowledge of the robotic system as well as the uncertainties of the environment are compensated for by a rule base structure which interacts with varying degrees of belief of control action using system measurements. An on-line adaptive algorithm was developed using a single parameter tuning scheme. In the effort presented, the methodology is further developed to include on-line scaling factor tuning and self-learning control as well as extended to the multi-input, multi-output (MIMO) case. Classical fuzzy logic control requires tuning input scale factors off-line through trial and error techniques. This is time-consuming and cannot adapt to new changes in the process. The new adaptive FLC includes a self-tuning scheme for choosing the scaling factors on-line. Further the rule base in classical FLC is usually produced by soliciting knowledge from human operators as to what is good control action for given circumstances. This usually requires full knowledge and experience of the process and operating conditions, which limits applicability. A self-learning scheme is developed which adaptively forms the rule base with very limited knowledge of the process. Finally, a MIMO method is presented employing optimization techniques. This is required for application to space robotics in which several degrees-of-freedom links are commonly used. Simulation examples are presented for terminal control - typical of robotic problems in which a desired terminal point is to be reached for each link. Future activities will be to implement the MIMO adaptive FLC on an INTEL microcontroller-based circuit and to test the algorithm on a robotic system at the Mars Mission Research Center at North Carolina State University.

Lee, Gordon↗

Optimized pulsed write schemes improve linearity and write speed for low-power organic neuromorphic devices

Neuromorphic devices are becoming increasingly appealing as efficient emulators of neural networks used to model real world problems. However, no hardware to date has demonstrated the necessary high accuracy and energy efficiency gain over CMOS in both training via backpropagation and in read via vector matrix multiplication. Such shortcomings are due to device non-idealities, particularly asymmetric conductance tuning in response to uniform voltage pulse inputs. Here, by formulating a general circuit model for capacitive ion-exchange neuromorphic devices, we show that asymmetric nonlinearity in organic electrochemical neuromorphic devices (ENODes) can be suppressed by an appropriately chosen write scheme. Simulations based upon our model suggest that a nonlinear write-selector could reduce the switching voltage and energy, enabling analog tuning via a continuous set of resistance states (100 states) with extremely low switching energy (~170 fJ • µm –2 ). Furthermore, this work clarifies the pathway to neural algorithm accelerators capable of parallelism during both read and write operations.

97 MATHEMATICS AND COMPUTING↗

Sputter-deposited WO x and MoO x for hole selective contacts

Here, reactive sputter deposited tungsten and molybdenum oxide (WO x , MoO x ) thin films are tested for their ability to form a hole selective contact for Si wafer based solar cells. A characterization approach based on analyzing the band bending induced in the c-Si absorber and the external and implied open-circuit voltage of test structures was used. It is shown that the oxygen partial pressure allows to tailor the selectivity to some extent and that a direct correlation between induced band bending and hole selectivity exists. Although the selectivity of the sputtered films is inferior to the reference films deposited by thermal evaporation, these results demonstrate a good starting point for further optimizations of sputtered WO x and MoO x towards higher work functions to improve the hole selectivity.

14 SOLAR ENERGY↗

Dual curved photonic crystal ring resonator based channel drop filter using two-dimensional photonic crystal structure

In this paper channel drop filter (CDF) is designed using dual curved photonic crystal ring resonator (PCRR). The photonic band gap (PBG) is calculated by plane wave expansion (PWE) method and the photonic crystal (PhC) based on two dimensional (2D) square lattice periodic arrays of silicon (Si) rods in air structure have been investigated using finite difference time domain (FDTD) method. The number of rods in Z and X directions is 21 and 20 respectively with lattice constant 0.540 nm and rod radius r = 0.1 µm. The channel drop filter has been optimized for telecommunication wavelengths λ = 1.591 µm with refractive indices 3.533. In the designed structure further analysis is also done by changing whole rods refractive index and it has been observed that this filter may be used for filtering several other channels also. The designed structure is useful for CWDM systems. This device may serve as a key component in photonic integrated circuits. The device is ultra compact with the overall size around 123 µm{sup 2}.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Engineering CAM Photosynthetic Machinery into Bioenergy Crops for Biofuels Production in Marginal Environments

CAM provides an excellent opportunity to engineer enhanced photosynthetic performance and water-use efficiency (WUE) into bioenergy crops. Our vision was to understand the enzymatic and regulatory pathways required for CAM in order to engineer CAM photosynthetic machinery into Arabidopsis and Populus. Major advances were made in understanding the molecular “parts list” necessary for engineering CAM through the sequencing the genomes and transcriptomes of several model and agronomically important CAM species including Agave, Ananas, Clusia, Kalanchoe, Mesembryanthemum, and Opuntia. Comparison of diel co-expression network analyses in Agave, Ananas, and Kalanchoe with expression patterns in C 3 photosynthesis species revealed the rescheduling of gene expression associated with stomatal opening and closing and led to the identification of many candidate CAM-related genes for further functional testing. Both RNAi-mediated gene silencing and CRISPR/Cas genome editing for gene knockout were used to investigate over 70 CAM-related enzymes, regulatory kinases/phosphatases, and transporters and 25 transcription factors implicated in playing key regulatory roles in CAM. Knockdown of key C 4 cycle enzymes within the carboxylation and decarboxylation modules of CAM not only perturbed CAM itself, but also altered the expression of core circadian clock components demonstrating that loss of CAM function also perturbs the central circadian clock and alters the regulatory patterns of key guard cell signaling genes that are linked with the characteristic inverse pattern of stomatal opening and closing during CAM. An advanced system for joining D.AN fragments from a universal library was developed that automatically maintains open reading frames (ORFs) and does not require linkers, adaptors, regions of sequence homology, amplification (or mutation for domestication) of fragments to function systems for the construction of gene circuits. Alternatively, Gibson assembly was used to create gene circuits consisting of up to 15 unique gene expression cassettes expressing either the core C 4 cycle of CAM comprising carboxylation or decarboxylation modules or both modules together. The expression of each gene cassette was driven by a drought-stress inducible 5’ regulatory region or promoter (and cognate 3’ terminator region) from A. thaliana so that CAM gene expression would be enhanced under conditions of water-deficit stress. These gene circuits were introduced into the C 3 photosynthesis model species A. thaliana. Expression of the nocturnal carboxylation module resulted in increased biomass and seed yield arising from net CO 2 fixation at night and malate accumulation typical of a CAM plant along with daytime CO 2 fixation typical of a C 3 photosynthesis plant. To create a leaf anatomy suited for the optimal performance of CAM in a C 3 photosynthesis plant, increased tissue succulence was engineered in A. thaliana (and Nicotiana sylvestris), which also improved biomass and seed yield and drought attenuation and improved salinity tolerance. The basic CAM Biodesign principles described in this report can be extended to increase the productivity and WUE of food and bioenergy crops and are expected to have broad applicability and ensure sustainable biofuel feedstock production in the face of the global climate crisis.

59 BASIC BIOLOGICAL SCIENCES↗

A New Approach to Identify Optimal Properties of Shunting Elements for Maximum Damping of Structural Vibration Using Piezoelectric Patches

The use of shunted piezoelectric patches in reducing vibration and sound radiation of structures has several advantages over passive viscoelastic elements, e.g., lower weight with increased controllability. The performance of the piezoelectric patches depends on the shunting electronics that are designed to dissipate vibration energy through a resistive element. In past efforts most of the proposed tuning methods were based on modal properties of the structure. In these cases, the tuning applies only to one mode of interest and maximum tuning is limited to invariant points when based on den Hartog's invariant points concept. In this study, a design method based on the wave propagation approach is proposed. Optimal tuning is investigated depending on the dynamic and geometric properties that include effects from boundary conditions and position of the shunted piezoelectric patch relative to the structure. Active filters are proposed as shunting electronics to implement the tuning criteria. The developed tuning methods resulted in superior capabilities in minimizing structural vibration and noise radiation compared to other tuning methods. The tuned circuits are relatively insensitive to changes in modal properties and boundary conditions, and can applied to frequency ranges in which multiple modes have effects.

Park, Junhong↗

Towards large-scale quantum optimization solvers with few qubits

Quantum computers hold the promise of more efficient combinatorial optimization solvers, which could be game-changing for a broad range of applications. However, a bottleneck for materializing such advantages is that, in order to challenge classical algorithms in practice, mainstream approaches require a number of qubits prohibitively large for near-term hardware. Here we introduce a variational solver for MaxCut problems over $m={{\mathcal{O}}}({n}^{k})$ binary variables using only n qubits, with tunable k > 1. The number of parameters and circuit depth display mild linear and sublinear scalings in m , respectively. Moreover, we analytically prove that the specific qubit-efficient encoding brings in a super-polynomial mitigation of barren plateaus as a built-in feature. Altogether, this leads to high quantum-solver performances. For instance, for m = 7000, numerical simulations produce solutions competitive in quality with state-of-the-art classical solvers. In turn, for m = 2000, experiments with n = 17 trapped-ion qubits feature MaxCut approximation ratios estimated to be beyond the hardness threshold 0.941. Our findings offer an interesting heuristics for quantum-inspired solvers as well as a promising route towards solving commercially-relevant problems on near-term quantum devices.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

New technology for recovering residual metals from nonmetallic fractions of waste printed circuit boards

Highlights: • Vibrated gas-solid fluidized bed can recycle residual metals from WPCBs. • Glass fibers have bad effect on vibrated gas-solid fluidized bed segregation. • Each size fraction has its own optimum segregation parameters. • Fine size fraction has the worst segregation efficiency. - Abstract: Recycling of waste printed circuit boards is important for environmental protection and sustainable resource utilization. Corona electrostatic separation has been widely used to recycle metals from waste printed circuit boards, but it has poor separation efficiency for finer sized fractions. In this study, a new process of vibrated gas-solid fluidized bed was used to recycle residual metals from nonmetallic fractions, which were treated using the corona electrostatic separation technology. The effects of three main parameters, i.e., vibration frequency, superficial air flow velocity, and fluidizing time on gravity segregation, were investigated using a vibrating gas-solid fluidized bed. Each size fraction had its own optimum parameters. Corresponding to their optimal segregation performance, the products from each experiment were analyzed using an X-ray fluorescence (XRF) and a scanning electron microscope (SEM) equipped with an energy dispersive spectrometer (EDS). From the results, it can be seen that the metal recoveries of −1 + 0.5 mm, −0.5 + 0.25 mm, and −0.25 mm size fractions were 86.39%, 82.22% and 76.63%, respectively. After separation, each metal content in the −1 + 0.5 or −0.5 + 0.25 mm size fraction reduced to 1% or less, while the Fe and Cu contents are up to 2.57% and 1.50%, respectively, in the −0.25 mm size fraction. Images of the nonmetallic fractions with a size of −0.25 mm indicated that a considerable amount of clavate glass fibers existed in these nonmetallic fractions, which may explain why fine particles had the poorest segregation performance.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Arylammonium-Assisted Reduction of the Open-Circuit Voltage Deficit in Wide-Bandgap Perovskite Solar Cells: The Role of Suppressed Ion Migration

Surface treatment using large alkyl/aryl ammonium cations has demonstrated reduced open-circuit voltage (V OC ) deficits in perovskite solar cells (PSCs), but the origin of the improvements has been vaguely attributed to defect passivation. Here, we combine the microscopic probing of the local electrical properties, thermal admittance spectroscopic analysis, and first principles calculations to elucidate the critical role of arylammonium interface layers on suppressing the ion migration in wide-bandgap (WBG) PSCs. Our results reveal that arylammonium surface treatment using phenethylammonium iodide increases the activation energy barrier for ion migration on the surface, which suppresses the accumulation of charge defects at surface and grain boundaries (GBs), leading to reduced dark saturation current density in WBG PSCs. Furthermore, with device optimization, our champion 1.73-eV PSC delivers a power conversion efficiency of 19.07% with a V OC of 1.25 V, achieving a V OC -deficit of 0.48 V.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Classical Preoptimization Approach for ADAPT-VQE: Maximizing the Potential of High-Performance Computing Resources to Improve Quantum Simulation of Chemical Applications

The ADAPT-VQE algorithm is a promising method for generating a compact ansatz based on derivatives of the underlying cost function, and it yields accurate predictions of electronic energies for molecules. In this work, we report the implementation and performance of ADAPT-VQE with our recently developed sparse wave function circuit solver (SWCS) in terms of accuracy and efficiency for molecular systems with up to 52 spin orbitals. The SWCS can be tuned to balance computational cost and accuracy, which extends the application of ADAPT-VQE for molecular electronic structure calculations to larger basis sets and a larger number of qubits. Using this tunable feature of the SWCS, we propose an alternative optimization procedure for ADAPT-VQE to reduce the computational cost of the optimization. Furthermore, by preoptimizing a quantum simulation with a parametrized ansatz generated with ADAPT-VQE/SWCS, we aim to utilize the power of classical high-performance computing in order to minimize the work required on noisy intermediate-scale quantum hardware, which offers a promising path toward demonstrating quantum advantage for chemical applications.

ADAPT-VQE↗

Delay-resolved spectroscopy in terahertz photonic circuits

Photonic integrated circuits incorporating intersubband transitions are ideal for mid-infrared and terahertz nanophotonics. However, the design of epitaxies has long been inhibited by two factors: the modest predictivity of ab initio theory and the absence of absolute intersubband gain and loss measurements under operating conditions. Existing measurements either yield inaccurate gain profiles or do not accurately assess dependence on frequency, bias, and temperature. Here, we present a delay-resolved absolute-referencing method for accurate gain evaluation without these limitations, addressing a long-standing challenge. By creating a photonic circuit that allows broadband pulses to traverse different lengths of a gain medium, we measure the absolute transmission of intersubband structures. Gain profiles match theoretical predictions at lower temperatures, with gain and dispersion clamping after lasing, and faster-than-expected degradation occurs at higher temperatures. Our approach provides a precise experimental evaluation of temperature-dependent gain performance and gives insight into optimizing temperature performance and frequency comb designs.

Optical spectroscopy↗