Search NASA⌕ Search

SEARCH · Search NASA

Results for “compositional properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,225 records · Page 68

Effect of volatile removal during molding on the properties of two phenolic-fiber composites

A comparison has been made of the effect of three volatile-removing techniques during molding on the properties of phenolic-fiber composites. The first technique involved heating the molding compound from one side, initiating the volatile-producing reactions, and driving these volatiles through the compound toward the cooler side. The second technique involved the application of a vacuum to the molding cavity before and during the cure cycle. The third technique was a combination of the first two. These techniques were used in the compression molding of phenolic-asbestos and phenolic-glass composites. The effects of both the individual and combined techniques on the mechanical, thermal, and sorption properties of the composites are reported.

Price, H. L.↗

Poly(vinylidene fluoride)/ CaCu{sub 3}Ti{sub 4}O{sub 12} and La doped CaCu{sub 3}Ti{sub 4}O{sub 12} composites with improved dielectric and mechanical properties

Highlights: • High ϵ′ PVDF/CCTO and La doped CCTO composites prepared by Extrusion. • With addition of ceramic, there is substantial increase in the ϵ′ of matrix PVDF. • Composites exhibit double relaxation behavior. - Abstract: Melt extrusion process has been used to prepare high relative permittivity, ϵ' PVDF–CCTO and PVDF–LaCCTO composites. Phase composition has been studied using powder X-ray diffraction (XRD). Microstructural, dielectric and mechanical properties have also been studied. Young's modulus of PVDF increases with the ceramic reinforcement. Dielectric measurements are made in the frequency range 10{sup −2}–10{sup 6} Hz using two probe Novocontrol impedance analyser (ZG4) from room temp to 120 °C to study the dielectric relaxation. There is a substantial increase in ϵ' of the matrix PVDF on addition of LaCCTO.

36 MATERIALS SCIENCE↗

Effect of adjusting composition on the crystallization and luminescence properties in NaYF{sub 4}:Er{sup 3+} embedded glass ceramics

Highlights: • Intense 2.7 μm emission was achieved in transparent glass ceramics containing NaYF{sub 4}:Er{sup 3+} nanocrystals. • The crystallization and luminescence properties of the nanocrystals embedded glass ceramics are tuned by adjusting the Na{sub 2}O/NaF ratio. • Modifying the properties of glass ceramics through adjusting the glass composition is an effective route. - Abstract: Intense 2.7 μm emission was achieved in transparent glass ceramics containing NaYF{sub 4}:Er{sup 3+} nanocrystals. The effect of adjusting Na{sub 2}O/NaF ratio in glass composition on the crystallizing and luminescence behavior in the glass ceramics was investigated. The controllable crystallization property of NaYF{sub 4} nanocrystals was remained after modifying the glass composition and the crystallization temperature was largely reduced for the samples with high Na{sub 2}O content. The X-ray diffraction and transmission electron microscopy analysis evidenced the shrink of lattice parameter with increasing Na{sub 2}O content. High transparency was kept for these glass ceramic samples, and intense upconversion, near- and mid-infrared emissions were obtained in Er{sup 3+}-doped glass ceramics with an increase of red/green ratio and prominent Stark splits in the sample with high Na{sub 2}O content, indicating the change of crystal field around Er{sup 3+} in the host matrix. Our results indicate that the crystallization and luminescence properties of glass ceramics could be modified through adjusting the glass composition, and it is an effective route to develop glass ceramics with favorable properties.

36 MATERIALS SCIENCE↗

Microstructure and Mechanical Properties of W-ZrC Composites Synthesized by Reactive Melt Infiltration of Zr{sub 2}Cu into Porous Preforms from Partially Carburized W Powders

W-ZrC composites with different W contents from 48 to 73 vol.% have been synthesized by reactive melt infiltration of Zr{sub 2}Cu melt into porous preforms from partially carburized W powders at 1300 °C for 1 h in vacuum. The influences of carbon content and porosity in the preforms on microstructure and mechanical properties of W-ZrC composites are investigated. Cold isostatic pressing followed by pre-sintering process is used to produce porous preforms with suitable porosities of 53.6-47% under a pressure of 100 MPa to allow sufficient penetration of Zr{sub 2}Cu melt into the preforms. Small amounts of Cu-rich phases form in the synthesized W-ZrC composites after a complete reaction of y/2xZr{sub 2}Cu(l) + WC{sub y}(s) = y/xZrC{sub x}(s) + W(s) + y/2xCu(l). These Cu-rich phases are distributed not only at the phase boundaries of W matrix and ZrC grains, but also in the interior of ZrC{sub x} grains. With decreasing W content from 73 to 48 vol.% in the W-ZrC composites, the flexural strength and fracture toughness increase from 519 to 657 MPa and from 9.1 to 10.6 MPa m{sup 1/2}, respectively.

36 MATERIALS SCIENCE↗

High temperature structural fibers: Status and needs

The key to high temperature structural composites is the selection and incorporation of continuous fiber reinforcement with optimum mechanical, physical, and chemical properties. Critical fiber property needs are high strength, high stiffness, and retention of these properties during composite fabrication and use. However, unlike polymeric composites where all three requirements are easily achieved with a variety of commercially available carbon-based fibers, structural fibers with sufficient stiffness and strength retention for high temperature metal, intermetallic, and ceramic composites are not available. The objective here is to discuss in a general manner the thermomechanical stability problem for current high performance fibers which are based on silicon and alumina compositions. This is accomplished by presenting relevant fiber property data with a brief discussion of potential underlying mechanisms. From this general overview, some possible materials engineering approaches are suggested which may lead to minimization and/or elimination of this critical stability problem for current high temperature fibers.

Dicarlo, James A.↗

High-Temperature Mechanical Properties of the P/M Extruded Mg-SiC{sub p} Composites

In the present study, pure magnesium reinforced with 0, 5, 10 and 15 vol.% SiC particulates was successfully prepared by powder metallurgy technique before being hot extruded. The average 14 μm grain size of the composite specimens remained almost unchanged after addition of SiC particles, while their dimensional stability was improved because of the reduction in the coefficient of thermal expansion (CTE) from 28.6 × 10{sup −6} K{sup −1} in pure Mg to 27.3, 25.3 and 23.4 × 10{sup −6} K{sup −1} in the Mg-5% SiC, Mg-10% SiC and Mg-15% SiC composites, respectively. Mechanical properties of the specimens were investigated in the temperature range of 298-498 K, implementing shear punch testing and hot hardness techniques. Depending on the test temperature, addition of SiC particles to the pure Mg matrix increased shear yield stress and ultimate shear strength of the materials by 5-25 and 6-23 MPa, respectively. The shear strength improvement was mainly attributed to the CTE mismatch strengthening mechanism (9.5-25.5 MPa), and to a lesser extent (1-4.5 MPa), to the load transfer mechanism. Finally, using the modified Clyne model, the contribution of different strengthening mechanisms to the total shear strength improvement in the composites was evaluated.

36 MATERIALS SCIENCE↗

Lunar Science Conference, 4th, Houston, Tex., March 5-8, 1973, Proceedings. Volume 1 - Mineralogy and petrology. Volume 2 - Chemical and isotope analyses. Organic chemistry. Volume 3 - Physical properties

The mineralogy, petrology, chemistry, isotopic composition, and physical properties of lunar materials are described in papers detailing methods, results, and implications of research on samples returned from eight lunar landing sites: Apollo 11, 12, 14, 15, 16, 17, and Luna 16 and 20. The results of experiments conducted or set up on the lunar surface by the astronauts are also described along with observations taken from Command Modules and subsatellites. Major topics include general geology, soil and breccia studies, petrologic studies, mineralogic analyses, elemental compositions, radiometric age determinations, rare gas chemistry, radionuclides, organogenic compounds, particle track records, thermal properties, seismic studies, resonance studies, orbital mapping, lunar atmosphere, magnetic studies, electrical studies, optical properties, and microcratering. Individual items are announced in this issue.

Gose, W. A.↗

Effect of post cure time and temperature on the properties of two phenolic-fiber composites

Some effects of post-cure time and temperature on the physicomechanical properties of a phenolic-asbestos and a phenolic-glass composite are studied. The molding and post-curing procedures are discussed along with physical and mechanical test results. It is found that the specific gravity of the panels tested decreased slightly but the hardness always increased with post cure, and that the mechanical properties had different patterns of response to increasing post-cure time and temperature. For tensile properties, strength decreased, modulus increased, and elongation at break exhibited little change. In general, the phenolic-asbestos showed more positive response to post cure than did the phenolic-glass. Mold venting is found to impart better properties to the composites concerned.

Lucy, M. H.↗

Preparation of MgH{sub 2} composite with a composition of 40%MgH{sub 2} + 30%LiBH{sub 4} + 30%(2LiBH{sub 4} + MgF{sub 2})

Graphical abstract: Hydrogen content vs. desorption time curves for consecutive 1st desorptions of 40 wt%MgH{sub 2} + 30 wt%LiBH{sub 4} + 30 wt%(2LiBH{sub 4} + MgF{sub 2}) at 533–873 K. Highlights: ► Addition of MgF{sub 2} and LiBH{sub 4} with a higher hydrogen storage capacity to MgH{sub 2}. ► Preparation of 40%MgH{sub 2} + 30%LiBH{sub 4} + 30% (2LiBH{sub 4} + MgF{sub 2}) composite. ► Examination of desorption properties of the composite. ► Total desorbed hydrogen quantity for consecutive 1st desorptions of 7.07 wt%. ► Reactions of LiBH{sub 4} → LiH + B + (3/2)H{sub 2}, and 2LiBH{sub 4} + MgF{sub 2} → 2LiF + MgB{sub 2} + 4H{sub 2}. -- Abstract: A mixture of containing two chemical equivalents of lithium borohyride and one equivalent of magnesium fluoride is known to yield hydrogen in an amount of about 7.6 wt% of the mixture when heated to about 150 °C at atmospheric pressure by the following reaction; 2LiBH{sub 4} + MgF{sub 2} = 2LiF + MgB{sub 2} + 4H{sub 2}. In order to increase hydrogen storage capacity of Mg-based materials, a mixture with a composition of 2LiBH{sub 4} + MgF{sub 2} and LiBH{sub 4}with a higher hydrogen storage capacity of 18.4 wt% were added to MgH{sub 2}. MgH{sub 2} composite with a composition of 40 wt%MgH{sub 2} + 30 wt%LiBH{sub 4} + 30 wt%(2LiBH{sub 4} + MgF{sub 2}) was prepared by reactive mechanical grinding. The hydrogen storage properties of the sample were then examined. Hydrogen content vs. desorption time curves for consecutive 1st desorptions of 40 wt%MgH{sub 2} + 30 wt%LiBH{sub 4} + 30 wt%(2LiBH{sub 4} + MgF{sub 2}) at 533–873 K showed that the total desorbed hydrogen quantity for consecutive 1st desorptions is 7.07 wt%.

36 MATERIALS SCIENCE↗

Numerical Simulation of Permeability Change in Wellbore Cement Fractures after Geomechanical Stress and Geochemical Reactions Using X-ray Computed Tomography Imaging

X-ray microtomography (XMT) imaging combined with a three-dimensional (3D) computational fluid dynamics (CFD) modeling technique was used to study the effect of geochemical and geomechanical processes on fracture properties in composite Portland cement–basalt caprock core samples. The effect of fluid properties and flow conditions on fracture permeability was numerically studied by using fluids with varying physical properties and simulating different pressure conditions. CFD revealed that the application of geomechanical stress led to increased fluid flow, which resulted in increased fracture permeability. After CO2-reaction, XMT images displayed preferential precipitation of calcium carbonate within the fractures in the cement matrix and less precipitation in fractures located at the cement–basalt interface. CFD predicted changes in flow characteristics and differences in absolute values of flow properties due to different pressure gradients. CFD was able to highlight the profound effect of fluid properties on flow characteristics and hydraulic properties of fractures. This study demonstrates the applicability of XMT imaging and CFD as powerful tools for characterizing the hydraulic properties of fractures in a number of applications like geologic carbon sequestration and storage, hydraulic fracturing for shale gas production, and enhanced geothermal systems.

CO2 storage↗

Effect of thermal spike on composite moisture capacity

As part of a continuing study of the effects of thermal spike on composite physical properties, severals sets of 16-ply TGDDM-DDS epoxy/graphite fiber composites were first saturated with moisture, and then individual specimens were subjected to thermal spikes of up to 240 C for periods of up to 25 minutes. At the cure temperature, 177 C, all sets show a change in rate of mass lost during spike. Post-spike moisture reabsorption capacity data provides evidence of temperature dependent molecular structural dilation and consolidation of the epoxide matrix. This evidence suggests that either a thermoreversible phenomenon such as physical aging or a nonreversible additional cure becomes active near the upper limit of the aircraft supersonic flight profile. These and other important observations suggest that one or more of several mechanisms may be active during thermal spike.

Adamson, M. J.↗

Ultrasonic Measurement Of Elastic Constants Of Composites

Ultrasonic testing system yields data on elastic constants of matrix/fiber laminated composite material. Related to one described in "Ultrasonic System Measures Elastic Properties of Composites" (NPO-18729). Tests performed nondestructive, and involve access by ultrasonic probes to only one side of material specimen. In comparison with other available ultrasonic testing systems, this system relatively inexpensive, and based on testing technique that is simpler and rapidly yields more-accurate results.

Bar-Cohen, Yoseph↗

Controlling properties by chemistry in doped shape memory alloys

Shape memory alloys find increasing use in airspace applications. Using theoretical and computational methods, we investigate correlations between the selected properties and composition in doped NiTi-based shape memory alloys. Among the properties we consider relative energies, phase transition temperature, and hysteresis. We compare predictions to experimental data. Our theoretical guidance facilitates design of future alloys. We acknowledge support from the NASA Transformative Aeronautics Concepts Program, Transformational Tools & Technologies (TTT) Project.

NiTi↗

Controlling properties by chemistry in doped shape memory alloys

Shape memory alloys find increasing use in airspace applications. Using theoretical and computational methods, we investigate correlations between the selected properties and composition in doped NiTi-based shape memory alloys. Among the properties we consider relative energies, phase transition temperature, and hysteresis. We compare predictions to experimental data. Our theoretical guidance facilitates design of future alloys.

Nikolai A Zarkevich↗

Role of Probabilistic Micromechanics Modeling in Establishing Design Allowables in Composites

One of the major challenges in designing with any new material, and particularly with advanced composite materials, is the fidelity of material design allowables. In the case of composite materials, the concern arises from the inherent nature of these materials, i.e., their heterogeneous make-up and the various factors that affect their properties in a specific design environment. Composites have various scales - micro, macro, laminate and structural, as well as numerous other fabrication related parameters. Many advanced composites in aerospace applications involve complex two- and three-dimensional fiber architectures and requires high-temperature processing. Since there are uncertainties associated with each of these, the observed behavior of composite materials shows scatter. Evaluating the effect of each of these variables on the observed scatter in composite properties solely by teSting is cost and time prohibitive. One alternative is to evaluate these effects by computational simulation. The authors have developed probabilistic composite micromechanics techniques by combining woven composite micromechanics and Fast Probability Integration (FPI) techniques to address these issues. In this paper these techniques will be described and demonstrated through selected examples. Results in the form of cumulative distribution functions (CDF) of the composite properties of a MI (melt-infiltrated) SiC/SiC (silicon carbide fiber in a silicon carbide matrix) Composite will be presented. A CDF is a relationship defined by the value of the property (the response variable) with respect to the cumulative probability of occurrence. Furthermore, input variables causing scatter are identified and ranked based upon their sensitivity magnitude. Sensitivity information is very valuable in quality control. How these results can be utilized to develop design allowables so that these materials may be used by structural analysts/designers will also be discussed.

Mital, Subodh K.↗

3D-Printing of Meso-structurally Ordered Carbon Fiber/Polymer Composites with Unprecedented Orthotropic Physical Properties

Here we report the first example of a class of additively manufactured carbon fiber reinforced composite (AMCFRC) materials which have been achieved through the use of a latent thermal cured aromatic thermoset resin system, through an adaptation of direct ink writing (DIW) 3D-printing technology. We have developed a means of printing high performance thermoset carbon fiber composites, which allow the fiber component of a resin and carbon fiber fluid to be aligned in three dimensions via controlled micro-extrusion and subsequently cured into complex geometries. Characterization of our composite systems clearly show that we achieved a high order of fiber alignment within the composite microstructure, which in turn allows these materials to outperform equivalently filled randomly oriented carbon fiber and polymer composites. Moreover, our AM carbon fiber composite systems exhibit highly orthotropic mechanical and electrical responses as a direct result of the alignment of carbon fiber bundles in the microscale which we predict will ultimately lead to the design of truly tailorable carbon fiber/polymer hybrid materials having locally programmable complex electrical, thermal and mechanical response.

36 MATERIALS SCIENCE↗