Search NASA⌕ Search

SEARCH · Search NASA

Results for “dissolving”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,225 records · Page 68

Vanadium redox flow battery efficiency and durability studies of sulfonated Diels Alder poly(phenylene)s

Sulfonated Diels Alder poly(phenylene) (SDAPP) was examined for vanadium redox flow battery (VRFB) use. The ion exchange capacity (IEC) was varied from 1.4, 1.6 and 2.0 meq/g in order to tune the proton conductivity and vanadium permeability. Coulombic efficiencies between 92 to 99% were observed, depending on IEC (lower IEC, higher coulombic efficiencies). In all cases the SDAPP displayed comparable energy efficiencies (88 - 90%) to Nafion 117 (88%) at 50mA/cm2. Membrane durability also was dependent on IEC; SDAPP with the highest IEC lasted slightly over 50 cycles while SDAPP with the lowest IEC lasted over 400 cycles and testing was discontinued only due to time constraints. Accelerated vanadium lifetime studies were initialed with SDAPP, by soaking films in a 0.1 M V5+ and 5.0 M total SO4-2 solution. The rate of degradation was also proportional with IEC; the 2 meq/g sample dissolved within 376 hours, the 1.6 meq/g sample dissolved after 860 hours, while the 1.4 meq/g sample broke apart after 1527 hours.

accelerated lifetime testing↗

Pt Catalyst Degradation in Aqueous and Fuel Cell Environments studied via In-Operando Anomalous Small-Angle X-ray Scattering

The evolution of Pt nanoparticle cathode electrocatalyst size distribution in a polymer electrolyte membrane fuel cell (PEMFC) was followed during accelerated stress tests using in-operando anomalous small-angle X-ray scattering (ASAXS). This evolution was compared to that observed in an aqueous electrolyte environment using stagnant electrolyte, flowing electrolyte, and flowing electrolyte at elevated temperature to reveal the different degradation trends in the PEMFC and aqueous environments and to determine the relevance of aqueous measurements to the stability of Pt nanoparticle catalyst in the fuel cell environment. The observed changes in the particle size distributions (PSDs) were analyzed to elucidate the extent and mechanisms of particle growth and corresponding mass and active surface area losses in the different environments. These losses indicate a Pt nanoparticle surface area loss mechanism controlled by Pt dissolution, the particle size dependence of Pt dissolution, the loss of dissolved Pt into the membrane and electrolyte, and, to a lesser extent, the re-deposition of dissolved Pt onto larger particles. Based on the geometric surface area loss, mass loss, and mean particle size increase trends, the aqueous environment best reflecting the fuel cell environment was found to be one in which the electrolyte is flowing rather than stagnant. Pt nanoparticle surface area loss resulting from potential cycling can be inhibited by reducing the number of particles smaller than a critical particle diameter (CPD), which was found to be similar to 3.5 to similar to 4 nm, with the CPD dependent on both the cycling protocol (square wave vs triangle wave) and the catalyst environment (fuel cell, aqueous stagnant, aqueous flowing electrolyte, or elevated temperature flowing electrolyte)

Anomalous small-angle X-ray scattering↗

An electrochemical study of hydrogen in molten 2LiF-BeF 2 (FLiBe) with addition of LiH

The chemical and transport behavior of hydrogen isotopes in molten 2LiF-BeF 2 (FLiBe) is of interest for the design of tritium management systems in nuclear fission and fusion reactors that use FLiBe. The chemical reaction of LiH with FLiBe is used to introduce hydrogen in the molten salt and electrochemical methods are used for in situ studies of hydrogen in FLiBe. LiH reacts with molten FLiBe to generate an electroactive species whose voltammetry peak is proportional to the added quantity of LiH. The cyclic voltammetry reaction potential of 2.009 ± 0.050 V vs Be/Be 2+ and the electron exchange of n = 0.8 ± 0.5 are consistent with the one-electron oxidation of dissolved H in the zero valence state, H o to H + . The concentration of H o is estimated by linear sweep voltammetry at 60–80% of the hydrogen introduced by the reaction of 0.42 mol% LiH with FLiBe and after eleven hours it remains above 40%. It is postulated that covalent BeH 2 is formed in FLiBe upon LiH addition, as a FLiBe-soluble quasi-stable intermediate product. Furthermore, the results provide an evaluation of LiH as a means of introducing dissolved hydrogen in FLiBe, enabling electrochemical methods as tools to advance the understanding of the chemistry of hydrogen isotopes in FLiBe.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Solute- and solvent-based electromotive force cells for activity measurements of electroactive species in molten salts

A novel combination of solute- and solvent-based electrodes was used to determine the activities of NdCl 3 and GdCl 3 in molten LiCI-KCI eutectic using electromotive force measurements across a broad concentration range of dissolved electroactive species. First, an electrochemical cell using solute-based electrodes was used to define the relative activity of each species as a function of concentration and the concentration region in which Henry's law was applicable. Next, the electromotive force between a solute-based electrode with a known NdCl 3 or GdCl 3 concentration and a solvent-based electrode with a known electromotive force was measured. The solvent-based electrode potential was converted to the Lithium Eutectic Electrode (LEE) potential, which allowed the activity of dissolved NdCl 3 and GdCl 3 to be calculated at the concentrations measured using the solute-based electrodes. The described two-cell method uses electromotive force measurements to accurately determine the activity of electroactive species over a wide concentration range and provides a simple approach to closing the knowledge gap of thermochemical properties of molten salts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

1-Butyl-3-methylimidazolium hydrogen sulfate catalyzed in-situ transesterification of Nannochloropsis to fatty acid methyl esters

We report 1-Butyl-3-methylimidazolium hydrogen sulfate ([Bmim][HSO 4 ]) is used as a solvent and an acid catalyst for in-situ extractive transesterification of wet Nannochloropsis with methanol. The reaction is supposed to be a five-step process: (1) wet algae cell wall dissolves in ionic liquid at reaction temperatures; (2) hydrogen ions and sulfate ions release from the ionization of HSO 4 - . The hydrogen ions (H+) act as catalysts for accelerating the reactive extraction of triglyceride from wet Nannochloropsis; (3) hydrogen ions and methanol molecules transfer from bulk to active site of cells without passing through cell wall that is dissolved by ionic liquid; (4) in-situ transesterification of lipid (mainly triglycerides) with methanol; and (5) products transfer from inside of algae cells to outside of cells. The crude biodiesel yield of [Bmim][HSO 4 ] catalyzed in-situ transesterification is about 95.28% at reaction temperature of 200 °C, reaction time of 30 min, mass ratio of [Bmim][HSO4] to wet Nannochloropsis of 0.9:1, and a mass ratio of methanol to wet algae of 3:1. It decreases to 81.23% after [Bmim][HSO 4 ] is recycled for 4 times, which indicates that [Bmim][HSO 4 ] catalyzed in-situ transesterification is an economic approach for biodiesel production from wet algae.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Investigation of enhanced CO 2 storage in deep saline aquifers by WAG and brine extraction in the Minnelusa sandstone, Wyoming

Geological CO 2 sequestration in deep saline aquifers has been extendedly investigated to reach the goal of carbon neutral as large amount of CO 2 can be reduced in a short time. Here, this study investigates the feasibility of water-alternating-gas (WAG) injection and brine extraction on enhancing CO 2 storage in a target deep saline aquifer, Minnelusa Sandstone in the Powder River Basin (PRB) of Wyoming. An integrated numerical model is developed to account for four scenarios: (1) CO 2 continuous injection (CI) through one injection well, (2) WAG injection through one injection well, (3) CO 2 CI through one injection well and brine extraction through one producer, (4) WAG injection through one injection well and brine extraction through one producer. Simulation results suggest that WAG injection and brine extraction corporately make it possible to enhance CO 2 injectivity while securing CO 2 storage safety. For instance, WAG injection considerably reduces structural trapping contribution while enhances dissolved and residual trapping contributions. As for brine extraction, it can decrease the maximum averaged reservoir pressure by 37% and 22% for CI and WAG injection, respectively. Besides, sensitive analyses of the operational parameters for the fourth scenarios are performed. Results reveal that, when the amount of total CO 2 injection has been predetermined, CO 2 injection time and rate within each period of WAG should be small whereas it is preferable to have large water injection time and rate. This is to secure desirable dissolved and residual trapping contributions (store CO 2 with safety). Sensitive degree results confirm that CO 2 injection rate, water injection time, and CO 2 injection time of WAG injection exhibit significant effects on CO 2 storage whereas the impacts of producer bottom-hole pressure (BHP), water injection rate, and CO 2 -water injection time are relatively weaker. This study not only sheds light on achieving double-win goal: enhance CO 2 injectivity and store CO 2 with safety, but also can be a critical reference for other CO 2 storage in deep saline aquifers.

58 GEOSCIENCES↗

Cerium dioxide (CeO2) nanoparticles decrease arsenite (As(III)) cytotoxicity to 16HBE14o- human bronchial epithelial cells

Highlights: • CeO{sub 2} NPs display a high adsorption capacity for As(III). • As(III) is highly toxic to lung 16HBE14o- cells (81% inhibition at 0.5 mg As/L). • As(III) adsorption onto CeO{sub 2} NPs decreased As(III) cytotoxicity on 16HBE14o- cells. • Cell uptake of As(III)-loaded CeO{sub 2} NPs did not lead to enhanced cytotoxicity. The production and application of engineered nanoparticles (NPs) are increasing in demand with the rapid development of nanotechnology. However, there are concerns that some of these novel materials could lead to emerging environmental and health problems. Some NPs are able to facilitate the transport of contaminants into cells/organisms via a “Trojan Horse” effect which enhances the toxicity of the adsorbed materials. In this work, we evaluated the toxicity of arsenite (As(III)) adsorbed onto cerium dioxide (CeO{sub 2}) NPs to human bronchial epithelial cells (16HBE14o-) using the xCELLigence real time cell analyzing system (RTCA). Application of 0.5 mg/L As(III) resulted in 81.3% reduction of cell index (CI, an RTCA measure of cell toxicity) over 48 h when compared to control cells exposed to medium lacking As(III). However, when the cells were exposed to 0.5 mg/L As(III) in the presence of CeO{sub 2} NPs (250 mg/L), the CI was only reduced by 12.9% compared to the control. The CeO{sub 2} NPs had a high capacity for As(III) adsorption (20.2 mg/g CeO{sub 2}) in the bioassay medium, effectively reducing dissolved As(III) in the aqueous solution and resulting in reduced toxicity. Transmission electron microscopy was used to study the transport of CeO{sub 2} NPs into 16HBE14o- cells. NP uptake via engulfment was observed and the internalized NPs accumulated in vesicles. The results demonstrate that dissolved As(III) in the aqueous solution was the decisive factor controlling As(III) toxicity of 16HBE14o- cells, and that CeO{sub 2} NPs effectively reduced available As(III) through adsorption. These data emphasize the evaluation of mixtures when assaying toxicity.

54 ENVIRONMENTAL SCIENCES↗

Dietary transfer of zinc oxide particles from algae (Scenedesmus obliquus) to daphnia (Ceriodaphnia dubia)

Highlights: • Toxicity of ZnO particles on algae and daphnia through dietary transfer was not more in 50 nm ZnO. • Contribution of ZnO {sub (total)} on toxicity was higher than ZnO {sub (ion)} through dietary transfer. • Biomagnification (BMF) ZnO particles was observed from algae to daphnia. • Uptake and accumulation particles caused significant ultra-structural damages in daphnia. The rapid increase in production and usage of ZnO particles in recent years has instigated the concerns regarding their plausible effects on the environment. Current study explores the trophic transfer potential of ZnO particles of different sizes (50, 100 nm and bulk particles) from algae (Scenedesmus obliquus) to daphnia (Ceriodaphnia dubia) and the contribution of ZnO{sub (ions)} (effect of dissolved Zn ions that remain in test medium after separation NPs) to the overall toxicity of ZnO{sub (total)} (impact of both particle and dissolved Zn ions). Toxicity and uptake of ZnO{sub (total)} and ZnO{sub (ions)} in algae were found to be dependent on the concentration and particle size. Feeding of Zn accumulated algae (517 ± 28, 354.7 ± 61 and 291 ± 20 µg/g dry wt.) post-exposure to 61 µM of ZnO{sub (total)} of 50, 100 nm and bulk ZnO particles caused a significant decrease in the survival (15–20%) of daphnia. A significant amount of Zn accumulation was observed in daphnia even after the 48 h depuration period. Biomagnification factor was found to be nearly 1 for all the sizes of ZnO particles tested. For 50 nm ZnO, the BMF was higher when compared to other two sizes, reaching the mean value of 1.06 ± 0.01 at 61 µM. Further analysis revealed that the dietary uptake of different sizes of ZnO particles caused ultra-structural damages and degradation of internal organs in daphnia.

54 ENVIRONMENTAL SCIENCES↗

Organic sulfur fluxes and geomorphic control of sulfur isotope ratios in rivers

Pyrite oxidation plays a critical role in the relationship between weathering and climate, and its impact on the global carbon cycle has previously been constrained through inversion models utilizing observations of river sulfate ($SO^{2–}_{4}$) and its 34 S/ 32 S isotope ratio (δ 34 S SO4 ). However, measurements from some rivers have suggested that SSO4 can be substantially impacted by processes such as microbial sulfate reduction and/or sulfur assimilation and cycling, rather than simply reflecting a weighted mixture of lithologic sulfur sources. To study the prevalence and controls on $SO^{2–}_{4}$ transformations, in this study we measured dissolved major element concentrations and δ 34 S SO4 in river water samples from throughout western Iceland. Our analyses focused on samples from a small catchment hosting the Efri Haukadalsá river, a system with relatively uniform and isotopically constrained basaltic bedrock. We also measured sediment δ 34 S and sulfur speciation using sulfur K-edge X-ray absorption spectroscopy on sediment and vegetation samples from this catchment. Values of dissolved δ 34 S SO4 in the Efri Haukadalsá ranged from 2.5‰ to 23.7‰ and had a linear relationship with Cl – /$SO^{2–}_{4}$ ratios, indicating that $SO^{2–}_{4}$ predominantly derived from basalt weathering and meteoric precipitation. The lower δ 34 S SO4 values were found in fluvial valleys with V-shaped cross sections, while higher values of δ 34 S SO4 occurred in U-shaped, glacially eroded valleys with thick alluvial fills blanketing the valley floor. Spectroscopic observations identified organic sulfur phases in suspended river sediment, floodplain deposits, and vegetation. Mass balance calculations quantified the organic sulfur flux as less than 10% of $SO^{2–}_{4}$ export, and sediment δ 34 S values were comparable to river δ 34 S SO4 . We interpreted these isotopic and chemical patterns as reflecting differences in the availability of unweathered bedrock across the Efri Haukadalsá catchment, with V-shaped valleys having greater access to fresh sulfide-bearing minerals than alluviated U-shaped valleys; this interpretation is in contrast to one in which the elevated δ 34 S SO4 values reflect fractionation during sulfur transformations along alluvial reaches. These results validated the application of river inversion models for constraining weathering fluxes and affirmed that pyrite oxidation globally, even in the presence of river sulfur cycling, modulates the abundance of atmospheric carbon dioxide.

54 ENVIRONMENTAL SCIENCES↗

Molecular dynamics simulations of zinc oxide solubility: From bulk down to nanoparticles

The solubility of metal oxides is one of the key descriptors for the evaluation of their potential toxic effects, both in the bulk form and in nanoparticulated aggregates. Current work presents a new methodology for the in silico assessment of the solubility of metal oxides, which is demonstrated using a well-studied system, ZnO. The calculation of the solubility is based on statistical thermodynamics tools combined with Density Functional Tight Binding theory for the evaluation of the free energy exchange during the dissolution process. Models of small ZnO clusters are used for describing the final dissolved material, since the complete ionic dissolution of ZnO is hindered by the formation of O2- anions in solution, which are highly unstable. Results show very good agreement between the computed solubility values and experimental data for ZnO bulk, up to 0.5 mg·L-1 and equivalents of 50 g·L-1 for the free Zn2+ cation in solution. However, the reference model for solid nanoparticles formed by free space nanoparticles can only give a limited quantitative solubility evaluation for ZnO nanoparticles.

DFTB modelling↗

Partitioning of oxygen isotopes during the aqueous solvation of nitric acid

Mixtures of water and inorganic acids show differences in isotopic composition between the vapor and liquid phases, reportedly even at an azeotrope. A recent reactive azeotropy analysis rationalized this by allowing for differences in stable isotope composition between bound solvation complexes and the bulk liquid. In this study, a mixture of water and nitric acid was examined experimentally to determine whether or not significant differences in stable isotope composition exist between bound solvation complexes and the bulk solution. A Rayleigh distillation was conducted using a solution of nitric acid and water. During the distillation, it was expected that bulk water would be vaporized first while (bound) water involved with hydrating the acid would be vaporized at later times along with the acid. Samples of both distillate and residual liquid were collected over time intervals and analyzed to determine oxygen and nitrogen stable isotope composition using isotope ratio mass spectrometry. Comparative samples were collected from the distillation of water alone. The measured oxygen fractionation factors suggest that the acid is preferentially hydrated with 18 O-enriched water, compared to the unbound, or bulk, water. Preferential coordination of 18 O-enriched water with the dissolved acid is consistent with heavier water forming stronger bonds relative to light water. Here, the results imply that isotope-dependent partitioning between bulk solvent and dissolved complexes may prove necessary in developing accurate descriptions of isotope fractionation during vapor-liquid equilibrium.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Arsenic repartitioning during biogenic sulfidization and transformation of ferrihydrite

Iron (hydr)oxides are strong sorbents of arsenic (As) that undergo reductive dissolution and transformation upon reaction with dissolved sulfide. Here we examine the transformation and dissolution of As-bearing ferrihydrite and subsequent As repartitioning amongst secondary phases during biotic sulfate reduction. Columns initially containing As(V)-ferrihydrite coated sand, inoculated with the sulfate reducing bacteria Desulfovibrio vulgaris (Hildenborough), were eluted with artificial groundwater containing sulfate and lactate. Rapid and consistent sulfate reduction coupled with lactate oxidation is observed at low As(V) loading (10% of the adsorption maximum). The dominant Fe solid phase transformation products at low As loading include amorphous FeS within the zone of sulfate reduction (near the inlet of the column) and magnetite downstream where Fe(II)(aq) concentrations increase; As is displaced from the zone of sulfidogenesis and Fe(III)(s) depletion. At high As(V) loading (50% of the adsorption maximum), sulfate reduction and lactate oxidation are initially slow but gradually increase over time, and all As(V) is reduced to As(III) by the end of experimentation. With the higher As loading, green rust(s), as opposed to magnetite, is a dominant Fe solid phase product. Independent of loading, As is strongly associated with magnetite and residual ferrihydrite, while being excluded from green rust and iron sulfide. Our observations illustrate that sulfidogenesis occurring in proximity with Fe (hydr)oxides induce Fe solid phase transformation and changes in As partitioning; formation of As sulfide minerals, in particular, is inhibited by reactive Fe(III) or Fe(II) either through sulfide oxidation or complexation.

58 GEOSCIENCES↗

Characterization of Uranium-Contaminated Sediments From Beneath A Nuclear Waste Storage Tank From Hanford, Washington: Implications for Contaminant Transport and Fate

The concentration and distribution of uranium (U) in sediment samples from three boreholes recovered near radioactive waste storage tanks at Hanford, Washington State, USA, were determined in detail using bulk and micro-analytical techniques. The source of contamination was a plume that contained an estimated 7000 kg of dissolved U that seeped into the subsurface as a result of an accident that occurred during filling of tank BX-102. The desorption character and kinetics of U were also determined by experiment in order to assess the mobility of U in the vadose zone. Most samples contained too little moisture to obtain quantitative information on pore water compositions. Concentrations of U (and contaminant phosphate—P) in pore waters were therefore estimated by performing 1:1 sediment-to-water extractions and the data indicated concentrations of these elements were above that of uncontaminated “background” sediments. Further extraction of U by 8 N nitric acid indicated that a significant fraction of the total U is relatively immobile and may be sequestered in mobilization-resistant phases. Fine- and coarse-grained samples in sharp contact with one another were sub-sampled for further scrutiny and identification of U reservoirs. Segregation of the samples into their constituent size fractions coupled with microwave-assisted digestion of bulk samples showed that most of the U contamination was sequestered within the fine-grained fraction. Isotope exchange ( 233 U) tests revealed that ~51 to 63% of the U is labile, indicating that the remaining fund of U is locked up in mobilization-resistant phases. Analysis by micro-X-Ray Fluorescence and micro-X-Ray Absorption Near-Edge Spectroscopy (μ-XRF and μ-XANES) showed that U is primarily associated with Ca and is predominately U(VI). The spectra obtained on U-enriched “hot spots” using Time-Resolved Laser-Induced Fluorescence Spectroscopy (TRLIFS) provide strong evidence for uranophane-type [Ca(UO 2 ) 2 (SiO 3 OH) 2 (H 2 O) 5 ] and uranyl phosphate [Ca(UO 2 ) 2 (PO 4 ) 2 (H 2 O) 10-12 ] phases. These data show that disseminated micro-precipitates can form in narrow pore spaces within the finer-grained matrix and that these objects are likely not restricted to lithic fragment environments. Uranium mobility may therefore be curtailed by precipitation of uranyl silicate and phosphate phases, with additional possible influence exerted by capillary barriers. Consequently, equilibrium-based desorption models that predict the concentrations and mobility of U in the subsurface matrix at Hanford are unnecessarily conservative.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Effects of aqueous uranyl speciation on the kinetics of microbial uranium reduction

The ability to predict the success of the microbial reduction of soluble U(VI) to highly insoluble U(IV) as an in situ bioremediation strategy is complicated by the wide range of geochemical conditions at contaminated sites and the strong influence of aqueous uranyl speciation on the bioavailability and toxicity of U(VI) to metal-reducing bacteria. In order to determine the effects of aqueous uranyl speciation on uranium bioreduction kinetics, incubations and viability assays with Shewanella putrefaciens strain 200 were conducted over a range of pH and dissolved inorganic carbon (DIC), Ca 2+ , and Mg 2+ concentrations. A speciation-dependent kinetic model was developed to reproduce the observed time series of total dissolved uranium concentration over the range of geochemical conditions tested. The kinetic model yielded the highest rate constant for the reduction of uranyl non-carbonate species (i.e., the ‘free’ hydrated uranyl ion, uranyl hydroxides, and other minor uranyl complexes), indicating that they represent the most readily reducible fraction of U(VI) despite being the least abundant uranyl species in solution. In the presence of DIC, Ca 2+ , and Mg 2+ is suppressed during the formation of more bioavailable uranyl non-carbonate species and resulted in slower bioreduction rates. At high concentrations of bioavailable U(VI), however, uranium toxicity to S. putrefaciens inhibited bioreduction, and viability assays confirmed that the concentration of non-carbonate uranyl species best predicts the degree of toxicity. The effect of uranium toxicity was accounted for by incorporating the free ion activity model of metal toxicity into the bioreduction rate law. These results demonstrate that, in the absence of competing terminal electron acceptors, uranium bioreduction kinetics can be predicted over a wide range of geochemical conditions based on the bioavailability and toxicity imparted on U(VI) by solution composition. Finally, these findings also imply that the concentration of uranyl non-carbonate species, despite being extremely low, is a determining factor controlling uranium bioreduction at contaminated sites.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Effects of calcium and phosphate on uranium(IV) oxidation: Comparison between nanoparticulate uraninite and amorphous U IV –phosphate

The mobility of uranium in subsurface environments depends strongly on its redox state, with U IV phases being significantly less soluble than U VI minerals. This study compares the oxidation kinetics and mechanisms of two potential products of U VI reduction in natural systems, a nanoparticulate UO 2 phase and an amorphous U IV –Ca–PO 4 analog to ningyoite (CaU IV (PO 4 ) 2 ·1–2H 2 O). The valence of U was tracked by X-ray absorption near-edge spectroscopy (XANES), showing similar oxidation rate constants for U IV O 2 and U IV –phosphate in solutions equilibrated with atmospheric O 2 and CO 2 at pH 7.0 (k obs,UO2 = 0.17 ± 0.075 h -1 vs. k obs,U IV PO4 = 0.30 ± 0.25 h -1 ). Addition of up to 400 μM Ca and PO 4 decreased the oxidation rate constant by an order of magnitude for both UO 2 and U IV –phosphate. The intermediates and products of oxidation were tracked by electron microscopy, powder X-ray diffraction (pXRD), and extended X-ray absorption fine-structure spectroscopy (EXAFS). In the absence of Ca or PO 4 , the product of UO 2 oxidation is Na–uranyl oxyhydroxide (under environmentally relevant concentrations of sodium, 15 mM NaClO 4 and low carbonate concentration), resulting in low concentrations of dissolved U VI (<2.5 × 10 -7 M). Oxidation of U IV –phosphate produced a Na-autunite phase (Na 2 (UO 2 )PO 4 ·xH 2 O), resulting in similarly low dissolved U concentrations (<7.3 × 10 -8 M). When Ca and PO 4 are present in the solution, the EXAFS data and the solubility of the UVI phase resulting from oxidation of UO 2 and UIV–phosphate are consistent with the precipitation of Na-autunite. Bicarbonate extractions and Ca K-edge X-ray absorption spectroscopy of oxidized solids indicate the formation of a Ca–UVI–PO 4 layer on the UO 2 surface and suggest a passivation layer mechanism for the decreased rate of UO 2 oxidation in the presence of Ca and PO 4 . Interestingly, the extractions were unable to remove all of the oxidized U from partially oxidized UO 2 solids, suggesting that oxidized U is distributed between the interior of the UO 2 nanoparticles and the labile surface layer. Accounting for the entire pool of oxidized U by XANES is the likely reason for the higher UO 2 oxidation rate constants determined here relative to prior studies. In conclusion, our results suggest that the natural presence or addition of Ca and PO 4 in groundwater could slow the rates of U IV oxidation, but that the rates are still fast enough to cause complete oxidation of U IV within days under fully oxygenated conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Rare earth element behavior during groundwater–seawater mixing along the Kona Coast of Hawaii

Groundwater and seawater samples were collected from nearshore wells and offshore along the Kona Coast of the Big Island of Hawaii to investigate rare earth element (REE) behavior in local subterranean estuaries. Previously we saw that submarine groundwater discharge (SGD) is the predominant flux of terrestrial waters to the coastal ocean along the arid Kona Coast of Hawaii. Groundwater and seawater samples were filtered through 0.45 μm and 0.02 μm pore-size filters to evaluate the importance of colloidal and soluble (i.e., truly dissolved ionic species and/or low molecular weight [LMW] colloids) fractions of the REEs in the local subterranean estuaries. Mixing experiments using groundwater collected immediately down gradient from a wastewater treatment facility (WWTF) proximal to the Kaloko-Hanokohau National Historic Park, and more “pristine” groundwater from a well constructed in a lava tube at Kiholo Bay, were conducted with local seawater to study the effect of solution composition (i.e., pH, salinity) on the concentrations and fractionation behavior of the REEs as groundwater mixes with seawater in Kona Coast subterranean estuaries. The mixed waters were also filtered through 0.45 or 0.02 μm filters to ascertain the behavior of colloidal and soluble fractions of the REEs across the salinity gradient in each mixing experiment. Concentrations of the REEs were statistically identical (two-tailed Student t-test, 95% confidence) between the sequentially filtered sample aliquots, indicating that the REEs occur as dissolved ionic species and/or LMW colloids in Kona Coast groundwaters. The mixing experiments revealed that the REEs are released to solution from suspended particles or colloids when Kona Coast groundwater waters mix with local seawater. The order of release that accompanies increasing pH and salinity follows light REE (LREE) > middle REE (MREE) > heavy REE (HREE). Release of REEs in the mixing experiments is driven by decreases in the free metal ion activity in solution and the concomitant increase in the amount of each REE that occurs in solution as dicarbonato complexes [i.e., Ln(CO 3 ) 2 - ] as pH increases across the salinity gradient. Input-normalized REE patterns of Kona Coast groundwater and coastal seawater are nearly identical and relatively flat compared to North Pacific seawater, indicating that SGD is the chief source of these trace elements to the ocean along the Kona Coast. Additionally, REE concentrations of the coastal seawater are between 10 and 50 times higher than previously reported open-ocean seawater values from the North Pacific, further demonstrating the importance of SGD fluxes of REEs to these coastal waters. Altogether, these observations indicate that large-scale removal of REEs, which characterizes the behavior of REEs in the low salinity reaches of many surface estuaries, is not a feature of the subterranean estuary along the Kona Coast. A large positive gadolinium (Gd) anomaly characterizes groundwater from the vicinity of the WWTF. The positive Gd anomaly can be traced to the coastal ocean, providing further evidence of the impact of SGD on the coastal waters. Estimates of the SGD fluxes of the REEs to the coastal ocean along the Kona Coast (i.e., 1.3–2.6 mmol Nd day -1 ) are similar to recent estimates of SGD fluxes of REEs along Florida’s east coast and to Rhode Island Sound, all of which points to the importance of SGD as significant flux of REEs to the coastal ocean.

58 GEOSCIENCES↗

Kinetics of D/H isotope fractionation between molecular hydrogen and water

At equilibrium, the D/H isotope fractionation factor between H 2 and H 2 O (α H 2 O-H 2 (eq) ) is a sensitive indicator of temperature, and has been used as a geothermometer for natural springs and gas discharges. However, δD H 2 measured in spring waters may underestimate subsurface temperatures of origin due to partial isotopic re-equilibration during ascent and cooling. In this work, we present new experimental data on the kinetics of D–H exchange for H 2 dissolved in liquid water at temperatures below 100 °C. Comparing these results with published exchange rates obtained from gas phase experiments (100–400 °C), we derive a consistent activation energy of 52 kJ/mol, and the following rate expressions; ln k =9.186 - 6298/ T and k 1 = 9764.61[H 2 O] e-6298/ T where T is absolute temperature (K), k is the universal rate constant ([L/mol]/hr), and k 1 is a pseudo-first-order constant (hr -1 ) applicable to water-dominated terrestrial systems by constraining [H 2 O] as the density of H 2 O (in mol/L) at the P-T of interest. The density-dependent rate constant accounts for the kinetic disparity of D–H exchange with H 2 when dissolved in liquid H 2 O relative to a gas/steam phase, exemplifed by 1/ k 1 at 100 °C of ~2 days in liquid, versus ~7 yrs in saturated steam. This difference may explain the high variability of δDH 2 observed in fumarolic gases. Fluids convecting in the crust frequently reach T > 225 °C, where isotopic equilibrium is rapidly attained (<1 hr). We compare fractionation factors measured in natural fluids (α OBS ) with values expected for equilibrium at the T of acquisition. Where these values differ, we use kinetic models to estimate cooling rates during upward advection that account for the observed disequilibrium. Models fit to fluids from Yellowstone Park and the Lost City (deep-sea) vent field, both recovered at ~90 °C, require respective transit times of ~7 hrs and ~11 days between higher temperature reaction zones and the surface. Using estimates of subsurface depths of origin, however, suggests similar mean fluid flow rates (10 s of meters/hr). Additional complications must be considered when interpreting the δDH 2 of lower-temperature effluent. When applied to data from deep-sea hydrothermal systems, our kinetic models indicate microbial catalysis accelerates D–H exchange once fluids cool below ~60 °C. The H 2 measured in both continental alkaline springs and fracture fluids from Precambrian shield rock is likely produced at T < 100 °C, through processes such as serpentinization. In these settings, δDH 2 values appear closer to equilibrium with H 2 O than those from geothermal systems. Considering kinetic isotope effects may yield H 2 that is out of equilibrium when generated at lower temperatures, we calculate maximum (isothermal) times to apparent isotopic equilibrium of 1.3 yrs at 50 °C, 9 yrs at 25 °C, and 35 yrs at 10 °C. A similar calculation applied to Antarctic brines (-13 °C), where measured δDH 2 is far from equilibrium, yields ~350 yrs. This time is shorter than the fluids have been isolated (2.8 ka), suggesting kinetic isotope effects associated with H 2 destruction or loss via diffusion may also be possible.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗