Search NASA⌕ Search

SEARCH · Search NASA

Results for “interphase”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,225 records · Page 68

Exploring the Promise of Multifunctional “Zintl-Phase-Forming” Electrolytes for Si-Based Full Cells

Li-M-Si ternary Zintl phases have gained attention recently due to their high structural stability, which can improve the cycling stability compared to a bulk Si electrode. Adding multivalent cation salts (such as Mg 2+ and Ca 2+ ) in the electrolyte was proven to be a simple way to form Li-M-Si ternary phases in situ in Si-based Li-ion cells. To explore the promise of Zintl-phaseforming electrolytes, we systematically investigated their application in pouch cells via electrochemical and multiscale postmortem analysis. The introduction of multivalent cations, such as Mg 2+ , during charging can form Li x M y Si ternary phases. They can stabilize Si anions and reduce side reactions with electrolyte, improving the bulk stability. More importantly, Mg 2+ and Ca 2+ incorporate into interfacial side reactions and generate inorganic-rich solid- electrolyte interphase, thus enhancing the interfacial stability. Therefore, the full cells with Zintl-phase-forming electrolytes achieve higher capacity retentions at the C/3 rate after 100 cycles, compared to a baseline electrolyte. Additionally, strategies for mitigating the electrode-level fractures of Si were evaluated to make the best use of Zintl-phase-forming electrolytes. In conclusion, this work highlights the significance of synergistic impact of multifunctional additives to stabilize both bulk and interface chemistry in high-energy Si anode materials for Li-ion batteries.

25 ENERGY STORAGE↗

Functionalized Silicon Particles for Enhanced Half- and Full-Cell Cycling of Si-Based Li-Ion Batteries

Vinylene carbonate (VC) and polyethylene oxide (PEO) have been investigated as functional agents that mimic the solid electrolyte interphase (SEI) chemistry of silicon (Si). VC and PEO are known to contribute to the stability of Si-based lithium-ion batteries as an electrolyte additive and as a SEI component, respectively. In this work, covalent surface functionalization was achieved via a facile route, which involves ball-milling the Si particles with sacrificial VC and PEO. Thermogravimetric analysis (TGA), X-ray photoelectron spectroscopy (XPS), and magic angle spinning nuclear magnetic resonance (MAS NMR) spectroscopy indicate that the additives are strongly bound to Si. In particular, MAS NMR shows Si–R or Si–O–R groups, which confirm functionalization of the Si after milling in VC or PEO. Particle size analysis by dynamic light scattering reveals that the additives facilitate particle size reduction and that the functionalized particles result in more stable dispersions based on zeta potential measurements. Raman mapping of the electrodes fabricated from the VC and PEO-coated active material with a polyacrylic acid (PAA) binder reveals a more homogenous distribution of Si and the carbon conductive additive compared to the electrodes prepared from the neat Si. Furthermore, the VC-milled Si strikingly exhibited the highest capacity in both half- and full-cell configurations, with more than 200 mAh g –1 measured capacity compared to the neat Si in the half-cell format. This is linked to an improved electrode processing based on the Raman and zeta potential measurements as well as a thinner SEI (with more organic components for the functionalized Si relative to the neat Si) based on XPS analysis of the cycled electrodes. In conclusion, the effect of binder was also investigated by comparing PAA with P84 (polyimide type), where an increased capacity is observed in the latter case.

25 ENERGY STORAGE↗

Computational Predictions of the Stability of Fluorinated Calcium Aluminate and Borate Salts

Energy storage concepts based on multivalent ions, such as calcium, have great potential to become next-generation batteries due to their low cost and comparable cell voltage and energy density to Li-ion batteries. However, the development of Ca batteries is still hindered by the lack of suitable materials that grant a long cycle life. Specific to electrolyte materials, developing a calcium salt that is chemically stable under ambient conditions and enables reversible electrodeposition of Ca is critical. In this work, we use first-principles calculations to study the intrinsic and reductive stability of twelve Ca salts with fluorinated aluminate and borate anions and analyze the decomposition products formed on the metal anode surface that are critical to early-stage solid electrolyte interphase formation. Here we found anions with significant steric hindrance and a high degree of fluorination are intrinsically less stable and deemed unviable designs for Ca salt. Aluminate salts are generally less reactive with the Ca anode than their borate counterparts, and a high degree of fluorination leads to weaker reductive stability. Calcium fluoride is the most prominent decomposition product on the anode surface, and carbide-like motifs were also found from the decomposition of the designed salts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Operation of Layered LiCoO 2 to Higher Voltages with a Localized Saturated Electrolyte

The commercialization of lithium-ion batteries started with the layered LiCoO 2 (LCO) cathode for portable electronics, but only 50% of its theoretical capacity can be used in practical cells due to detrimental surface and bulk degradations when charged to high voltages. Here we demonstrate here that the stability of electrolyte plays a critical role in the performance of LCO at high voltages by employing a localized saturated electrolyte (LSE). With a cutoff voltage of 4.5 V, LCO achieves an initial 1C discharge capacity of 176 mA h g -1 and a capacity retention of 80% over 230 cycles. Even with a cutoff voltage of 4.6 V, LCO with 2% aluminum doping displays an initial discharge capacity of 189 mA h g -1 at 1C rate with 80% capacity retention over 137 cycles. With extensive analytical characterization, we show that the improved cycling stability stems from a suppression of the O3 to H1-3 phase transition as well as a robust inorganic-rich cathode-electrolyte interphase (CEI) facilitated by the LSE. This work highlights the importance of protecting the surface as well as the bulk with appropriate electrolytes for the high-voltage, higher-energy-density operation of LCO.

25 ENERGY STORAGE↗

Probing the Effectiveness in Stabilizing Lithium Metal Anodes through Functional Additives

A variety of electrolyte additives were comprehensively evaluated to understand their relative capability in stabilizing lithium metal anode. Although the Li||Cu test is an effective test to rule out ineffective additives, a reliable assessment of individual additives cannot be obtained just by a single evaluation method. Therefore, various methods must be combined to truly assess the stabilization of a lithium anode. Moreover, it was also discovered that a significant depletion of electrolytes occurred during the end-of-life of the lithium batteries, which partially contributed to the sudden failure of the lithium batteries during cycling. However, the main culprit of the sudden failure was identified as the significant increase in the resistance of the lithium metal anode. Further, when used as an additive, cyclic fluorinated carbonates are the most effective in stabilizing the lithium anode and improving the cycling performance of lithium batteries among all the common additives. Despite its cost-effectiveness, the additive in the conventional electrolyte approach provides insufficient protection for lithium metal due to the complete consumption of the additive materials, which is necessary to repair the solid-electrolyte interphase (SEI). Therefore, it is suggested that a larger ratio (>15 wt %) of the SEI former should be employed to achieve effective lithium stabilization.

25 ENERGY STORAGE↗

Tailoring Solvation Solvent in Localized High-Concentration Electrolytes for Lithium||Sulfurized Polyacrylonitrile

Sulfurized polyacrylonitrile (SPAN) is a promising cathode material for lithium-sulfur (Li-S) batteries due to its significantly reduced polysulfide (PS) dissolution compared to the elemental S cathode. Although conventional carbonate-based electrolytes is stable with SPAN electrodes, it is less stable with Li metal anode (LMA). Recently, localized high-concentration electrolytes (LHCEs) have been developed to improve the stability of LMA. Here, we report a new strategy to further improve the performance of LI||SPAN batteries by replacing the conventional solvating solvent 1,2-dimethoxyethane (DME) in the LHCE with a new solvating solvent, 1,2-diethoxyethane (DEE), the new LHCEs exhibits less reactivity against Li 2 S 2 , alleviates PS dissolution, forms a better cathode-electrolyte interphase layer on the SPAN, and enhances structure reversibility even at elevated temperature (ET, 45°C). With the same salt and diluent as in other LHCEs, the LHCE with DEE leads to better performance in Li||SPAN batteries (with 82.9% capacity retention after 300 cycles at ET), preservation of SPAN cathode structure, and suppression of the volume change of LMA. The similar strategy on tailoring the solvating solvents in LHCEs can also be used in other rechargeable batteries to improve their performances.

1,2-diethoxyethane↗

Comparative Study of Vinylene Carbonate and Lithium Difluoro(oxalate)borate Additives in a SiO x /Graphite Anode Lithium-Ion Battery in the Presence of Fluoroethylene Carbonate

The SiO x /graphite composite is recognized as a promising anode material for lithium-ion batteries (LIBs), owing to the high theoretical capacity of SiO x combined with the excellent stability of graphite. However, the inherent disadvantage of volume expansion in silicon-based anodes places significant challenges on the solid electrolyte interphase (SEI) and severely degrades the electrochemical performance. Rational formulation of electrolyte, including its additives, is crucial in accommodating and optimizing the composition of the SEI and enhancing the cell performance. In this work, we present a comparative study of vinylene carbonate (VC) and lithium difluoro(oxalate)borate (LiDFOB) additives combined with fluoroethylene carbonate (FEC) in the electrolyte for SiO x /graphite∥LiNi 1–x–y–z Co x Mn y Al z O 2 full cells. VC outperformed LiDFOB as an additive, delivering higher capacity cycling, higher Coulombic efficiency, and better cycle stability up to 400 cycles. XPS and impedance analyses reveal that LiDFOB contributed to SEI/CEI with both a lower proportion of LiF and a higher proportion of poly(VC), which tended to produce higher cell impedance. XRD and XANES further indicated that using the LiDFOB additive, the NCMA cycled to a shallower degree than that of the VC additive. Although the VC additive maintained a higher capacity up to 400 cycles, microstrain and SEM analyses show a higher strained NCMA along with clear evidence of cracking over the surface of the NCMA particle in VC-based electrolyte but not in LiDFOB. In conclusion, this suggests that the negative influence of LiDFOB at the anode (inferior SEI) supersedes the negative impact of both a cracked NCMA and a deeper cycled NCMA and SiO x -based anode.

36 MATERIALS SCIENCE↗

Rational Electrolyte Design for Elevated-Temperature and Thermally Stable Lithium-Ion Batteries with Nickel-Rich Cathodes

As the energy density of lithium-ion batteries (LIBs) increases, the shortened cycle life and the increased safety hazard of LIBs are drawing increasing concerns. To address such challenges, a series of localized high-concentration electrolytes (LHCEs) based on a solvating-solvent mixture of tetramethylene sulfone and trimethyl phosphate and a high flash-point diluent 1H,1H,5H-octafluoropentyl 1,1,2,2-tetrafluoroethyl ether were designed. The LHCEs exhibited non-flammability and greatly suppressed heat release at high temperatures, which would potentially improve the safety performance of the LIBs. Moreover, the optimal LHCE achieved capacity retentions of 87.1% and 81.7% in graphite||LiNi 0.8 Mn 0.1 Co 0.1 O 2 cells after 500 cycles at 25 °C and 45 °C, respectively, which were significantly better than the conventional electrolyte, whose capacity retentions were only 75.2% and 38.5% under the same condition. Mechanistic studies revealed that the LHCE not only formed a more robust solid electrolyte interphase, but also exhibited improved anodic stability, compared with the conventional electrolyte. Further, this work sheds light in rational electrolyte design for high energy density LIBs with high battery performance and low safety concerns.

25 ENERGY STORAGE↗

Passivation dynamics in the anisotropic deposition and stripping of bulk magnesium electrodes during electrochemical cycling

Rechargeable magnesium (Mg) batteries show promise for use as a next generation technology for high-density energy storage, though little is known about the Mg anode solid electrolyte interphase and its implications for the performance and durability of a Mg-based battery. We explore in this report passivation effects engendered during the electrochemical cycling of a bulk Mg anode, characterizing their influences during metal deposition and dissolution in a simple, nonaqueous, Grignard electrolyte solution (ethylmagnesium bromide, EtMgBr, in tetrahydrofuran). Scanning electron microscopy images of Mg foil working electrodes after electrochemical polarization to dissolution potentials show the formation of corrosion pits. The pit densities so evidenced are markedly potential-dependent. When the Mg working electrode is cycled both potentiostatically and galvanostatically in EtMgBr these pits, formed due to passive layer breakdown, act as the foci for subsequent electrochemical activity. Detailed microscopy, diffraction, and spectroscopic data show that further passivation and corrosion results in the anisotropic stripping of the Mg {0001} plane, leaving thin oxide-comprising passivated side wall structures that demark the {0001} fiber texture of the etched Mg grains. Upon long-term cycling, oxide side walls formed due to the pronounced crystallographic anisotropy of the anodic stripping processes, leading to complex overlay anisotropic, columnar structures, exceeding 50 μm in height. Finally, the passive responses mediating the growth of these structures appear to be an intrinsic feature of the electrochemical growth and dissolution of Mg using this electrolyte.

36 MATERIALS SCIENCE↗

Quantification of the Mass and Viscoelasticity of Interfacial Films on Tin Anodes Using EQCM-D

Electrochemical quartz crystal microbalance coupled with dissipation (EQCM-D) is employed to explore the solid electrolyte interphase (SEI) formation and Li insertion/deinsertion into thin film electrodes of tin. Due to the frequency change we find that the initial SEI formation process is rapid before Li insertion but varies significantly with increasing concentration of the additive fluoroethylene carbonate (FEC) in the electrolyte. The extent of dissipation, which represents the film rigidity, increases with cycle number, reflecting film thickening and softening. Dissipation values are almost twice as large in the baseline electrolyte (1.2 M LiPF 6 in 3:7 wt % ethylene carbonate:ethyl methyl carbonate), indicating the film in baseline electrolyte is roughly twice as soft as in the FEC-containing cells. More importantly, we detail how quantitative data about mass, thickness, shear elastic modulus, and shear viscosity in a time-resolved manner can be obtained from the EQCM-D response. These parameters were extracted from the frequency and dissipation results at multiple harmonics using the Sauerbrey and Voigt viscoelastic models. From these modeled results we show the dynamic mass changes for each half cycle. We also demonstrate that different amounts of FEC additive influence the SEI formation behavior and result in differences in the estimated mass, shear modulus and viscosity. After three cycles, the film in baseline electrolyte exhibits a 1.2 times larger mass change compared with the film in the FEC-containing electrolyte. The shear elastic modulus of films formed in the presence of FEC is larger than in the baseline electrolyte at early stages of lithiation. Also with lithiation is a marked increase in film viscosity, which together point to a much stiffer and more homogeneous SEI formed in the presence of FEC.

36 MATERIALS SCIENCE↗

Ionic Associations and Hydration in the Electrical Double Layer of Water-in-Salt Electrolytes

Water-in-Salt-Electrolytes (WiSEs) are an exciting class of concentrated electrolytes finding applications in energy storage devices because of their expanded electrochemical stability window, good conductivity and cation transference number, and fire-extinguishing properties. These distinct properties are thought to originate from the presence of an anion-dominated ionic network and interpenetrating water channels for cation transport, which indicates that associations in WiSEs are crucial to understanding their properties. Currently, associations have mainly been investigated in the bulk, while little attention has been given to the electrolyte structure near electrified interfaces. Here, we develop a theory for the electrical double layer (EDL) of WiSEs, where we consistently account for the thermoreversible associations of species into Cayley tree aggregates. The theory predicts an asymmetric structure of the EDL. At negative voltages, hydrated Li + dominates, and cluster aggregation is initially slightly enhanced before disintegration at larger voltages. At positive voltages, when compared to the bulk, clusters are strictly diminished. Performing atomistic molecular dynamics (MD) simulations of the EDL of WiSE provides EDL data for validation and bulk data for parametrization of our theory. Validating the predictions of our theory against MD showed good qualitative agreement. Furthermore, we performed electrochemical impedance measurements to determine the differential capacitance of the studied LiTFSI WiSE and also found reasonable agreement with our theory. Overall, the developed approach can be used to investigate ionic aggregation and solvation effects in the EDL, which, among other properties, can be used to understand the precursors for solid-electrolyte interphase formation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Critical Insights into Solvent Choice for High-Voltage Organosulfur Electrolytes

Organosulfur electrolytes are promising candidates for enabling high-voltage cathodes due to their superior oxidative stability compared to conventional carbonate-based systems. However, their viscous nature and inability to passivate the anode necessitate the use of passivating agents and diluents to achieve meaningful charge/discharge rates. In this study, we investigate the use of cyclic fluorinated carbonates (CFCs) to form passivating interphases on electrode surfaces, aiming to optimize electrolyte performance in high-voltage systems. Electrolyte formulations containing 1.2 M LiPF 6 in a CFC:sulfone:1,1,2,2-tetrafluoroethyl-2,2,3,3-tetrafluoropropylether (TTE) mixture (2/5/3 V/V/V) were assessed in full-cell configurations with a LiNi 0.8 Mn 0.1 Co 0.1 O 2 (FCG-NMC) cathode and a 4.5 V upper cutoff potential. The results reveal that 3-3-3-trifluoropropylene carbonate (TFPC) combined with ethyl methyl sulfone (EMS) optimizes electrolyte performance, resulting in lower resistance buildup and reduced capacity loss compared to commercial electrolytes. We also explore the failure mechanisms of several carbonate/sulfone mixtures and identify key considerations for electrolyte compatibility in high-voltage systems. TFPC enhances cycling stability and lowers overall cell resistance, while fluoroethylene carbonate (FEC) formulations, despite higher ionic conductivity, fail to form adequate passivation layers, leading to rapid capacity loss. Additionally, EMS provides superior physical properties that avoid common failure modes seen with other sulfone solvents like methyl isopropyl sulfone and tetramethylene sulfone. Furthermore, this study underscores the importance of carefully selecting passivating carbonates and sulfone solvents to improve electrolyte performance and expand the viability of high-voltage electrolyte systems.

LiNi0.8Mn0.1Co0.1O2 cathode↗

Reactivity of Carbonate Solvent Electrolytes on Lithium Silicon Anodes

Silicon (Si) is promising for lithium-ion battery (LIB) anodes due to their high theoretical capacity and low electrochemical potential. However, significant challenges remain, including severe volumetric expansion during cycling and the electrochemical instability of electrolytes, which leads to the formation of a nonuniform solid electrolyte interphase (SEI). To investigate SEI formation mechanisms, computational molecular dynamics simulations offer valuable insights. In this work, we examine the trajectories and charge transfer behavior of lithium hexafluorophosphate (LiPF 6 ) salt with various solvent compositions using density functional theory (DFT) and ab initio molecular dynamics (AIMD). Among the tested electrolyte systems, LiPF 6 with vinylene carbonate (VC) added to ethyl methyl carbonate (EMC) exhibits the lowest reactivity with the Si anode. In contrast, the effects of fluoroethylene carbonate (FEC) and VC depend on whether the primary solvent is EMC alone or a mixture of ethylene carbonate (EC) and EMC. Moreover, we show that electrolyte reactivity varies with the degree of lithiation of the Si anode (LiSi vs Li 15 Si 4 ) and under different charge states. To decouple electrolyte reactivity from surface effects, we analyze the dissociation and formation energies of individual species from solvated configurations. Overall, these first-principles-based findings provide a strategic foundation for electrolyte design to improve cycling stability and extend calendar life in LIBs using Si anodes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Operando Depth-Resolved Measurement of Solvation Entropy, Interfacial Transport, and Charge-Transfer Kinetics in Lithium-Ion Batteries

Understanding and improving the performance and longevity of lithium-ion batteries critically depends on insight into the dynamic processes occurring at buried electrode-electrolyte interfaces. However, direct, depth-resolved, and operando diagnosis of these interfaces remains a longstanding challenge due to their inaccessibility beneath bulk materials, the limitations of conventional surface- and bulk-sensitive characterization tools, and the difficulty of maintaining realistic cell environments during measurement. These challenges have made it nearly impossible to uniquely resolve important interfacial properties such as charge transfer resistance, SEI (solid electrolyte interphase) resistance, and solvation entropy at the individual electrode interfaces within a working cell, information that is essential for mechanistic insight and accelerated battery design. Here, in this study, we report the development of multiharmonic electro-thermal spectroscopy (METS), an operando technique that enables depth-resolved measurement of solvation entropy, interfacial transport resistance, charge-transfer resistance, and SEI resistance at individual electrode-electrolyte interfaces within practical lithium-ion batteries. By leveraging frequency-dependent, thermal-wave sensing and interface-specific modeling, METS uniquely attributes interfacial properties to specific electrodes, as validated by comparison with traditional electrochemical impedance spectroscopy (EIS). The ability to spatially and temporally resolve interfacial processes in real time provides new diagnostic capabilities that are crucial for mechanistic studies of battery degradation and for the rapid development of next-generation energy storage systems.

Chalise, Divya [University of California, Berkeley↗

Role of Manganese Deposition on Graphite in the Capacity Fading of Lithium Ion Batteries

Lithium-ion batteries utilizing manganese based cathodes have received considerable interest in recent years for their lower cost and favorable environmental friendliness relative to their cobalt counterparts. However, Li-ion batteries using manganese based cathodes and graphite anodes suffer from severe capacity fading at higher operating temperature. In this article, we report on an astute investigation into how the dissolution of manganese impacts the capacity fading within the Li-ion batteries. Our investigation reveals that the manganese dissolves from the cathode, transports to the graphite electrode, and deposits onto the outer surface of the inner most solid electrolyte interphase (SEI) layer which is known to be a mixture of inorganic salts (e.g. Li2CO3, LiF, and Li2O). In this location, the manganese facilitates the reduction of the electrolyte and the subsequent formation of lithium containing products on the graphite which removes lithium ions from the normal operation of the cell and thereby induces the severe capacity fade.

Environmental Molecular Sciences Laboratory↗

A Fluorinated Ether Electrolyte Enabled High Performance Prelithiated Graphite/Sulfur Batteries

Lithium/sulfur (Li/S) batteries have attracted great attention as a promising energy storage technology, but so far their practical applications are greatly hindered by issues of polysulfide shuttling and unstable lithium/electrolyte interface. To address these issues, a feasible strategy is to construct a rechargeable prelithiated graphite/sulfur batteries. In this study, a fluorinated ether of bis(2,2,2-trifluoroethyl) ether (BTFE) was reported to blend with 1,3-dioxolane (DOL) for making a multifunctional electrolyte of 1.0 M LiTFSI DOL/BTFE (1:1, v/v) to enable high performance prelithiated graphite/S batteries. First, the electrolyte significantly reduces polysulfide solubility to suppress the deleterious polysulfide shuttling and thus improves capacity retention of sulfur cathodes. Second, thanks to the low viscosity and good wettability, the fluorinated electrolyte dramatically enhances the reaction kinetics and sulfur utilization of high-areal-loading sulfur cathodes. More importantly, this electrolyte forms a stable solid-electrolyte interphase (SEI) layer on graphite surface and thus enables remarkable cyclability of graphite anodes. Lastly, by coupling prelithiated graphite anodes with sulfur cathodes with high areal capacity of ~3 mAh cm -2 , we demonstrate prelithiated graphite/sulfur batteries that show high sulfur-specific capacity of ~1000 mAh g -1 and an excellent capacity retention of >65% after 450 cycles at C/10.

25 ENERGY STORAGE↗

Multinuclear NMR Study of the Solid Electrolyte Interface Formed in Lithium Metal Batteries

The composition of the solid electrolyte interphase (SEI) layers associated with a high performance Cu|Li cell using lithium bis(fluorosulfonyi)imide (LiFSI) in 1,2-dimethoxyethane (DME) as electrolyte is determined by a multinuclear (6Li, 19F, 13C and 1H) solid-state MAS NMR study at high magnetic field (850 MHz). This cell can be cycled at high rates (4 mA•cm-2) for more than 1000 cycles with no increase in the cell impedance at high Columbic efficiency (average of 98.4%) in a highly concentrated LiFSI-DME electrolyte (4 M). LiFSI, LiF, Li2O2 (and/or CH3OLi), LiOH, Li2S and Li2O are observed in the SEI and validated by comparing with the spectra acquired on standard compounds and literature reports. To gain further insight into the role of the solute and its concentration dependence on the formation of SEIs while keeping the solvent of DME unchanged, the SEIs from different concentrations of LiFSI-DME and lithium bis(trifluoromethanesulfonyl)imide (LiTFSI)-DME electrolyte are also investigated. It is found that LiF, a lithiated compound with superior mechanical strength and good Li+ ionic conductivity, is observed in the concentrated 4.0 M LiFSI-DME and the 3.0 M LiTFSI-DME systems but not in the diluted 1.0 M LiFSI-DME system. Li2O exists in both low and high concentration of LiFSI-DME while no Li2O is observed in the LiTFSI system. Furthermore, the dead metallic Li is reduced in the 4 M LiFSI-DME system compared with that in the 1 M LiFSI-DME system. Quantitative 6Li MAS results indicate that the SEI associated with the 4 M LiFSI-DEME is denser or thicker than that of the 1 M LiFSI-DME and the 3 M LiTFSI-DME systems. These findings are likely the reasons for explaining the high electrochemical performance associated with the high concentration LiFSI-DME system.

25 ENERGY STORAGE↗

Self-Assembly of Large Gold Nanoparticles for Surface-Enhanced Raman Spectroscopy

Performance of portable technologies from mobile phones to electric vehicles is currently limited by the energy density and lifetime of lithium batteries. Expanding the limits of battery technology requires in situ detection of trace components at electrode–electrolyte interphases. Surface-enhance Raman spectroscopy could satisfy this need if a robust and reproducible substrate were available. Gold nanoparticles (Au NPs) larger than 20 nm diameter are expected to greatly enhance Raman intensity if they can be assembled into ordered monolayers. A three-phase self-assembly method is presented that successfully results in ordered Au NP monolayers for particle diameters ranging from 13 to 90 nm. The monolayer structure and Raman enhancement factors (EFs) are reported for a model analyte, rhodamine, as well as the best performing polymer electrolyte salt, lithium bis(trifluoromethane)sulfonimide. Experimental EFs for the most part correlate with predictions based on monolayer geometry and with numerical simulations that identify local electromagnetic field enhancements. Lastly, the EFs for the best performing Au NP monolayer are between 10 6 and 10 8 and give quantitative signal response when analyte concentration is changed.

36 MATERIALS SCIENCE↗