Search NASA⌕ Search

SEARCH · Search NASA

Results for “mass diffusivity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,225 records · Page 68

Isotopic fractionation of Kr and Xe implanted in solids at very low energies

Results on the implantation of Kr and Xe in W under closed system conditions at very low energies (50-500 eV) are reported. Investigation of the fraction of gas trapped as a function of time reveals the existence of competing trapping and release mechanisms, and analysis of recovered trapped gas and residual gas phases shows that both elemental and isotropic fractionation result from these mechanisms. It is determined that the mass dependence for the overall implantation process is at or near m exp 1, with heavier isotopes enriched in the implanted gas. This mass dependence is inferred to result from implantation and a combination of diffusive and gas sputtering release mechanisms. These results reaffirm the conclusion of Bernatowicz and Fahey (1986) that previously observed isotopic fractionation of Kr and Xe in carbonaceous material synthesized in electrical discharges owes its origin to low-energy ion implantation, and also suggest that this process may be relevant to incorporation of noble gases in early solar system materials. The implication of these results for noble gas mass spectrometry are discussed.

Bernatowicz, Thomas J.↗

The effect of prewhirl on the internal aerodynamics and performance of a mixed flow research centrifugal compressor

The internal three-dimensional steady and time-varying flow through the diffusing elements of a centrifugal impeller were investigated using a moderate scale, subsonic, mixed flow research compressor facility. The characteristics of the test facility which permit the measurement of internal flow conditions throughout the entire research compressor and radial diffuser for various operating conditions are described. Results are presented in the form of graphs and charts to cover a range of mass flow rates with inlet guide vane settings varying from minus 15 degrees to plus 45 degrees. The static pressure distributions in the compressor inlet section and on the impeller and exit diffuser vanes, as well as the overall pressure and temperature rise and mass flow rate, were measured and analyzed at each operating point to determine the overall performance as well as the detailed aerodynamics throughout the compressor.

Bryan, William B.↗

Suppression of donor-vacancy clusters in germanium by concurrent annealing and irradiation

Diffusion of phosphorous and arsenic in germanium under in situ proton irradiation has been performed and analyzed with secondary ion mass spectrometry. Dopant profiles corresponding to proton-exposed regions exhibit a higher penetration depth and more pronounced box shape than profiles of nonexposed regions. Continuum theoretical simulations reveal that diffusion under irradiation is much less affected by inactive donor-vacancy clusters than diffusion under annealing only. The suppression of donor-vacancy clusters is caused by interstitials in supersaturation and vacancy concentrations close to thermal equilibrium. Concurrent annealing and irradiation have the potential to attain high active doping levels in Ge.

36 MATERIALS SCIENCE↗

The FUNPET—a New Hybrid Ion Funnel-Ion Carpet Atmospheric Pressure Interface for the Simultaneous Transmission of a Broad Mass Range

An atmospheric pressure interface transports ions from ambient pressure to the low-pressure environment of a mass spectrometer. A capillary coupled to an ion funnel is widely used. However, conventional ion funnels do little to negate the large amount of energy picked up by high-mass ions from the gas flow through the capillary. There has been little work done on the effects of gas flow on ion transmission, and the previous studies have all been limited to low-mass, low-charge ions. In this work, we account for the effects of gas flow, diffusion, and electric fields (static and oscillating) on ion trajectories and use simulations to design a new hybrid ion funnel-ion carpet (FUNPET) interface that transmits a broad mass range with a single set of instrument conditions. The design incorporates a virtual jet disruptor where pressure buildup and counter flow dissipate the supersonic jet that results from gas flow into the interface. This, and the small exit aperture that can be used with the FUNPET, reduces the gas flow into the next stage of differential pumping. The virtual jet disruptor thermalizes ions with a broad range of masses (1 kDa to 1 GDa), and once thermalized, they are transmitted into next region of the mass spectrometer with low excess kinetic energy. The FUNPET interface is easy to fabricate from flexible printed circuit board and a support frame made by 3D printing. The performance of the interface was evaluated using charge detection mass spectrometry. .

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Mathematical simulation of heat and mass transfer in a cylindrical channel versus the tangential momentum accommodation coefficient

The process of heat and mass transfer in a long cylindrical channel has been considered in terms of the mirror–diffuse model of the Maxwell boundary condition. The Hazen–Williams equation is used as a basic equation of the process kinetics. A constant temperature gradient is maintained in the channel. The heat and mass fluxes through the cross section of the channel versus the tangential momentum accommodation coefficient have been calculated in a wide range of the Knudsen number. The heat flux profiles have been constructed. A comparison with relevant published data has been carried out.

42 ENGINEERING↗

An Update on the Non-Mass-Dependent Isotope Fractionation under Thermal Gradient

Mass flow and compositional gradient (elemental and isotope separation) occurs when flu-id(s) or gas(es) in an enclosure is subjected to a thermal gradient, and the phenomenon is named thermal diffusion. Gas phase thermal diffusion has been theoretically and experimentally studied for more than a century, although there has not been a satisfactory theory to date. Nevertheless, for isotopic system, the Chapman-Enskog theory predicts that the mass difference is the only term in the thermal diffusion separation factors that differs one isotope pair to another,with the assumptions that the molecules are spherical and systematic (monoatomic-like structure) and the particle collision is elastic. Our previous report indicates factors may be playing a role because the Non-Mass Dependent (NMD) effect is found for both symmetric and asymmetric, linear and spherical polyatomic molecules over a wide range of temperature (-196C to +237C). The observed NMD phenomenon in the simple thermal-diffusion experiments demands quantitative validation and theoretical explanation. Besides the pressure and temperature dependency illustrated in our previous reports, efforts are made in this study to address issues such as the role of convection or molecular structure and whether it is a transient, non-equilibrium effect only.

Sun, Tao↗

Enhancing reactant selectivity for Ni/Mg reforming catalysts using silicalite-1 shells: A modeling study

The ability of a zeolite shell to enhance the selective conversion of hydrocarbons through diffusional limitations was investigated using a multi-scale model of a fixed-bed reactor. The impact of shell thickness and molecule/pore size on the catalytic performance of silicalite-1 zeolite encapsulated nickel catalyst pellets for steam reforming of C1-C7 hydrocarbons is reported. A reaction–diffusion model using kinetic expressions established in literature was employed. The model was verified through comparison with reported experimental results for steam reforming data over a temperature range of 748 – 1113 K and pressure of 1 – 10 bar. Comparisons are also made against experimental data for steam reforming in the presence of a zeolite shell. Evaluation of the Weisz-Prater criterion for both the core and encapsulated catalyst confirmed mass transfer limitation induced by the utilization of a zeolite shell. The model was used to suggest an optimal thickness that balances diffusional limitations imposed by the zeolite layer on methane versus that of the heavier hydrocarbons. The optimum thickness varied as a function of hydrocarbon size and shape which determined the diffusion rates. For toluene and heptane, a 50 nm thick shell was sufficient to wholly prevent reaction. Hydrocarbons like propane and butane required a shell 7.5 and 5 μm thick. Increasing the gas-hourly-space-velocity from 10,000 to 60,000 h –1 caused a decrease in the optimum shell thickness. Furthermore, this approach can be modified for application to other mixed hydrocarbon systems to predict optimal catalyst design.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Final Report for Subcontract B541028, Pore-Scale Modeling to Support "Pore Connectivity" Research Work

This report covers modeling aspects of a combined experimental and modeling task in support of the DOE Science and Technology Program (formerly OSTI) within the Office of Civilian Radioactive Waste Management (OCRWM). Research Objectives The research for this project dealt with diffusive retardation: solute moving through a fracture diffuses into and out of the rock matrix. This diffusive exchange retards overall solute movement, and retardation both dilutes waste being released, and allows additional decay. Diffusive retardation involves not only fracture conductivity and matrix diffusion, but also other issues and processes: contaminants may sorb to the rock matrix, fracture flow may be episodic, a given fracture may or may not flow depending on the volume of flow and the fracture's connection to the overall fracture network, the matrix imbibes water during flow episodes and dries between episodes, and so on. The objective of the project was to improve understanding of diffusive retardation of radionuclides due to fracture / matrix interactions. Results from combined experimental/modeling work were to (1) determine whether the current understanding and model representation of matrix diffusion is valid, (2) provide insights into the upscaling of laboratory-scale diffusion experiments, and (3) help in evaluating the impact on diffusive retardation of episodic fracture flow and pore connectivity in Yucca Mountain tuffs. Questions explored included the following: (1) What is the relationship between the diffusion coefficient measured at one scale, to that measured or observed at a different scale? In classical materials this relationship is trivial; in low-connectivity materials it is not. (2) Is the measured diffusivity insensitive to the shape of the sample? Again, in classical materials there should be no sample shape effect. (3) Does sorption affect diffusive exchange in low-connectivity media differently than in classical media? (4) What is the effect of matrix saturation on the effective diffusivity? Is it different for low-connectivity media than for classical media? (5) In addition to changing the matrix saturation (and thereby the diffusion coefficient), the wetting/drying cycles drive water into, and then out of, the matrix. How do these mass flow cycles affect the long-term exchange of solutes between the fracture and the matrix? Can it be treated as a simple increase in effective diffusivity? Is it a local or a global effect? Is the effect different in low-connectivity media? The modeling portion of this project primarily focused on how diffusion varies with pore connectivity, and it also connected the experimental work to theory.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Strongly enhanced incorporation of oxygen into barium titanate based multilayer ceramic capacitors using water vapor

The reoxidation of sintered BaTiO{sub 3}-based multilayer ceramic capacitors (MLCCs) is currently an empirically determined, but poorly understood, procedure. In this work, the incorporation of oxygen into BaTiO{sub 3}-based MLCCs has been studied by means of isotope exchange annealing ({sup 18}O{sub 2}/{sup 16}O{sub 2}, {sup 1}H{sub 2}{sup 18}O/{sup 1}H{sub 2}{sup 16}O or {sup 2}H{sub 2}{sup 16}O/{sup 1}H{sub 2}{sup 16}O) and subsequent determination of the isotope profiles in the solid by secondary ion mass spectrometry. Oxygen isotope profiles in the barium titanate dielectric can be described by a bulk diffusion coefficient D* and a surface exchange coefficient k*. The values obtained for k* indicate that oxygen incorporation from H{sub 2}O is much faster than from dry O{sub 2}; it thus plays the key role in the reoxidation process.

36 MATERIALS SCIENCE↗

Atomic Mixing of Initially Separated Mixtures

We consider the atomic mixing of two materials, initially separated in space, at fixed temperature– pressure conditions [T, p], and zero mass-mean velocity. Each material is composed of a specified set of atomic species whose density corresponds to the specieswise real Equation of State (EOS) $\tilde{&#961}$ i [T, p]. Because there are no spatial gradients in the mean [T, p] state, the only mechanism for mixing is a specieswise nonequilibrium thermal velocity distribution. The recipe for nonequilibrium species mass fluxes is taken directly from Hirschfelder, Curtiss, and Bird, who express the diffusion velocities in terms of gradients in the molar concentrations and pairwise coefficients of diffusion. EOS data from the SESAME library is used for all species. Data for the specieswise self diffusion coefficients is adopted from the Orbital Free Molecular Dynamics (OFMD) simulations of Ticknor et al.; the so-called Darken approximation is used to express the mutual diffusion coefficients of a mixture in the manner used by White et al. A one-dimensional spatial domain is used; with the left half occupied by one multispecies material and the right half occupied by the other, and with zero–gradient boundary conditions at the ends of the domain. Hence the total mass in the domain is a constant. At time t = 0 the materials are separated. Accordingly, spatial gradients at the separation point are infinite and the species fluxes are also infinite. As t → $\textbf{∞}$ the spatial gradients approach zero and a uniform set of species concentrations is obtained; at this point the system is said to be at “thermodynamic equilibrium.” Analytic solution of the problem is not possible in general due to the nonlinear concentration dependence of the species fluxes. Hence we utilize the numerical solution apparatus in Mathematica for obtaining accurate time-dependent solutions for the mixing of various initial species masses for conditions of interest in laser-driven Inertial Confinement Fusion. Concentration profiles and the speed of propagation of the mixing fronts are discussed in light of the nonlinearity of the problem.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Closed Loop Active Flow Separation Detection and Control in a Multistage Compressor

Active closed loop flow control was successfully demonstrated on a full annulus of stator vanes in a low speed axial compressor. Two independent methods of detecting separated flow conditions on the vane suction surface were developed. The first technique detects changes in static pressure along the vane suction surface, while the second method monitors variation in the potential field of the downstream rotor. Both methods may feasibly be used in future engines employing embedded flow control technology. In response to the detection of separated conditions, injection along the suction surface of each vane was used. Injected mass flow on the suction surface of stator vanes is known to reduce separation and the resulting limitation on static pressure rise due to lowered diffusion in the vane passage. A control algorithm was developed which provided a proportional response of the injected mass flow to the degree of separation, thereby minimizing the performance penalty on the compressor system.

Bright, Michelle M.↗

Magnetic coupling in the disks around young gas giant planets

We examine the conditions under which the disks of gas and dust orbiting young gas giant planets are sufficiently conducting to experience turbulence driven by the magneto-rotational instability. By modeling the ionization and conductivity in the disk around proto-Jupiter, we find that turbulence is possible if the X-rays emitted near the Sun reach the planet's vicinity and either (1) the gas surface densities are in the range of the minimum-mass models constructed by augmenting Jupiter's satellites to solar composition, while dust is depleted from the disk atmosphere, or (2) the surface densities are much less, and in the range of gas-starved models fed with material from the solar nebula, but not so low that ambipolar diffusion decouples the neutral gas from the plasma. The results lend support to both minimum-mass and gas-starved models of the protojovian disk. (1) The dusty minimum-mass models have internal conductivities low enough to prevent angular momentum transfer by magnetic forces, as required for the material to remain in place while the satellites form. (2) The gas-starved models have magnetically active surface layers and a decoupled interior 'dead zone'. Similar active layers in the solar nebula yield accretion stresses in the range assumed in constructing the circumjovian gas-starved models. Our results also point to aspects of both classes of models that can be further developed. Non-turbulent minimum-mass models will lose dust from their atmospheres by settling, enabling gas to accrete through a thin surface layer. For the gas-starved models it is crucial to learn whether enough stellar X-ray and ultraviolet photons reach the circumjovian disk. Additionally, the stress-to-pressure ratio ought to increase with distance from the planet, likely leading to episodic accretion outbursts.

79 ASTRONOMY AND ASTROPHYSICS↗

Experimental and Numerical Investigation of the NASA High Efficiency Centrifugal Compressor Vaned Stage Geometry and Aerodynamic Performance

Since its inception in the early 2010s, the NASA High Efficiency Centrifugal Compressor (HECC) has been enigmatic for the propulsion research community: experimental data and numerical simulations of the stage have generally not aligned in their quantifications of performance metrics. Typically, the fault for these disagreements is assigned to the numerical simulations as the simulations are models, and models are inherently incomplete representations of the experiment. This “incompleteness” may manifest in assumptions regarding roughness or heat transfer, simplifications of the flow path (i.e., neglecting bleed flows), or the oft-scapegoated turbulence model. In the case of HECC, recent work showed unexpected discrepancies between the intended impeller geometry defined in the design report (termed Design-Intent) and the manufactured impeller used in the experimental campaigns (termed As-Manufactured). That work used numerical simulations to establish that the geometric differences between the Design-Intent and As-Manufactured impellers were significant enough to result in drastically different performance predictions for the HECC vaneless diffuser configuration. The Design-Intent impeller simulations over predicted the performance relative to the experiment, whereas the As-Manufactured simulations better represented the experimental data, both in terms of one-dimensional performance metrics and spanwise flow profiles. This effort expands on that work by examining in detail the geometry and aerodynamic performance of the HECC vaned diffuser configuration. Further differences between the Design-Intent and As-Manufactured geometries have been discovered in the vaned diffuser and exit guide vanes, and these differences are documented herein. The summations of the geometric differences for all of the components were used to create two numerical models of HECC vaned diffuser configuration: the Design-Intent simulations which are generated from the original geometry definitions given in the design report and the As-Manufactured simulations which are the best available representation of the manufactured compressor hardware used in the experimental test campaigns. In congruence with the earlier vaneless diffuser work, the numerical predictions of the Design-Intent choked mass flow rate, total pressure ratio, and efficiency were notably greater than that of the As-Manufactured simulations. To increase confidence in the experimental dataset, measurements from a recent test campaign conducted in 2024 are used to validate the original experimental data acquired from 2012 to 2014 with good repeatability overall, especially considering the passage of time and differences in the data acquisition systems between the test campaigns. Both numerical simulations were then extensively evaluated against the experimental data. The As-Manufactured simulations provided better estimates of the stage performance than the Design-Intent cases in terms of most performance metrics. Nonetheless, more detailed results still show opportunities for improvement. Despite a more accurate representation of the physical hardware, characterization of the impeller work input remains a challenge even for rigorously developed numerical models.

vaned diffuser↗

Bulk Growth of Wide Band Gap II-VI Compound Semiconductors by Physical Vapor Transport

The mechanism of physical vapor transport of II-VI semiconducting compounds was studied both theoretically, using a one-dimensional diffusion model, as well as experimentally. It was found that the vapor phase stoichiometry is critical in determining the vapor transport rate. The experimental heat treatment methods to control the vapor composition over the starting materials were investigated and the effectiveness of the heat treatments was confirmed by partial pressure measurements using an optical absorption technique. The effect of residual (foreign) gas on the transport rate was also studies theoretically by the diffusion model and confirmed experimentally by the measurements of total pressure and compositions of the residual gas. An in-situ dynamic technique for the transport rate measurements and a further extension of the technique that simultaneously measured the partial pressures and transport rates were performed and, for the first time, the experimentally determined mass fluxes were compared with those calculated, without any adjustable parameters, from the diffusion model. Using the information obtained from the experimental transport rate measurements as guideline high quality bulk crystal of wide band gap II-VI semiconductor were grown from the source materials which undergone the same heat treatment methods. The grown crystals were then extensively characterized with emphasis on the analysis of the crystalline structural defects.

Su, Ching-Hua↗

Bulk Growth of Wide Band Gap II-VI Compound Semiconductors by Physical Vapor Transport

The mechanism of physical vapor transport of II-VI semiconducting compounds was studied both theoretically, using a one-dimensional diffusion model, as well as experimentally. It was found that the vapor phase stoichiometry is critical in determining the vapor transport rate. The experimental heat treatment methods to control the vapor composition over the starting materials were investigated and the effectiveness of the heat treatments was confirmed by partial pressure measurements using an optical absorption technique. The effect of residual (foreign) gas on the transport rate was also studies theoretically by the diffusion model and confirmed experimentally by the measurements of total pressure and compositions of the residual gas. An in-situ dynamic technique for the transport rate measurements and a further extension of the technique that simultaneously measured the partial pressures and transport rates were performed and, for the first time, the experimentally determined mass fluxes were compared with those calculated, without any adjustable parameters, from the diffusion model. Using the information obtained from the experimental transport rate measurements as guideline high quality bulk crystal of wide band gap II-VI semiconductor were grown from the source materials which undergone the same heat treatment methods. The grown crystals were then extensively characterized with emphasis on the analysis of the crystalline structural defects.

Su, Ching-Hua↗

Sodium diffusion in 4H-SiC

Sodium diffusion has been studied in p-type 4H-SiC. Heat treatments have been performed from 1200 °C to 1800 °C for 1 min to 4 h. Secondary ion mass spectrometry has been used to measure the sodium distribution. We show that sodium has a considerable mobility at 1200 °C in p-type 4H-SiC. On the other hand for sodium atoms trapped at suitable sites the mobility is limited up to 1800 °C. Trap limited diffusion kinetics is suggested and an effective diffusivity has been extracted with an activation energy of 4 eV for sodium diffusion in p-type 4H-SiC.

36 MATERIALS SCIENCE↗

Experimental and Numerical Investigation of the NASA High Efficiency Centrifugal Compressor Vaned Stage Geometry and Aerodynamic Performance

Since its inception in the early 2010s, the NASA High Efficiency Centrifugal Compressor (HECC) has been enigmatic for the propulsion research community: experimental data and numerical simulations of the stage have generally not aligned in their quantifications of performance metrics. Typically, the fault for these disagreements is assigned to the numerical simulations as the simulations are models, and models are inherently incomplete representations of the experiment. This “incompleteness” may manifest in assumptions regarding roughness or heat transfer, simplifications of the flow path (i.e., neglecting bleed flows), or the oft-scapegoated turbulence model. In the case of HECC, recent work showed unexpected discrepancies between the intended impeller geometry defined in the design report (termed Design-Intent) and the manufactured impeller used in the experimental campaigns (termed As-Manufactured). That work used numerical simulations to establish that the geometric differences between the Design-Intent and As-Manufactured impellers were significant enough to result in drastically different performance predictions for the HECC vaneless diffuser configuration. The Design-Intent impeller simulations over predicted the performance relative to the experiment, whereas the As-Manufactured simulations better represented the experimental data, both in terms of one-dimensional performance metrics and spanwise flow profiles. This effort expands on that work by examining in detail the geometry and aerodynamic performance of the HECC vaned diffuser configuration. Further differences between the Design-Intent and As-Manufactured geometries have been discovered in the vaned diffuser and exit guide vanes, and these differences are documented herein. The summations of the geometric differences for all of the components were used to create two numerical models of HECC vaned diffuser configuration: the Design-Intent simulations which are generated from the original geometry definitions given in the design report and the As-Manufactured simulations which are the best available representation of the manufactured compressor hardware used in the experimental test campaigns. In congruence with the earlier vaneless diffuser work, the numerical predictions of the Design-Intent choked mass flow rate, total pressure ratio, and efficiency were notably greater than that of the As-Manufactured simulations. To increase confidence in the experimental dataset, measurements from a recent test campaign conducted in 2024 are used to validate the original experimental data acquired from 2012 to 2014 with good repeatability overall, especially considering the passage of time and differences in the data acquisition systems between the test campaigns. Both numerical simulations were then extensively evaluated against the experimental data. The As-Manufactured simulations provided better estimates of the stage performance than the Design-Intent cases in terms of most performance metrics. Nonetheless, more detailed results still show opportunities for improvement. Despite a more accurate representation of the physical hardware, characterization of the impeller work input remains a challenge even for rigorously developed numerical models.

centrifugal compressor↗

Characterization of oxygen and titanium diffusion at the anatase TiO2(001) surface

The diffusion of intrinsic defects in a single crystal anatase TiO2(001) film was explored by isotopic labeling and static secondary ion mass spectrometry. Using both 46Ti and 18O as isotopic labels, we show that the anatase surface responds to redox imbalances by diffusion of both Ti and O into the bulk under vacuum reduction and (at least) Ti from the bulk to the surface during oxidation. The diffusion of Ti between the bulk and surface in anatase TiO2(001) closely resembles what was observed in the literature for the rutile TiO2(110) surface, however the latter is not known to have oxygen diffusion between the bulk and surface under typical ultrahigh vacuum conditions. We speculate that the open lattice of the anatase bulk structure may facilitate independent diffusion of both point defects (Ti interstitials and O vacancies) or concerted diffusion of "TiO" subunits. The authors gratefully acknowledge S.A. Chambers of Pacific Northwest National Laboratory (PNNL) for providing the anatase samples. This research was supported by the U.S. Department of Energy (DOE) Office of Basic Energy Sciences, Chemical Sciences, Geosciences, and Biosciences Division, the Office of Naval Research Contract Number 200CAR262, and the Oregon Nanoscience and Microtechnologies Institute. PNNL is operated for the U.S. DOE by Battelle under Contract Number DE05-AC76RL0 1830. The research was performed in the William R. Wiley Environmental Molecular Sciences Laboratory, a national scientific user facility funded by the U.S. DOE Office of Biological and Environmental Research.

Herman, Gregory S.↗