Search NASA⌕ Search

SEARCH · Search NASA

Results for “rough surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,225 records · Page 68

Epitaxial GaN layers formed on langasite substrates by the plasma-assisted MBE method

In this publication, the results of development of the technology of the epitaxial growth of GaN on single-crystal langasite substrates La{sub 3}Ga{sub 5}SiO{sub 14} (0001) by the plasma-assisted molecular-beam epitaxy (PA MBE) method are reported. An investigation of the effect of the growth temperature at the initial stage of deposition on the crystal quality and morphology of the obtained GaN layer is performed. It is demonstrated that the optimal temperature for deposition of the initial GaN layer onto the langasite substrate is about ~520°C. A decrease in the growth temperature to this value allows the suppression of oxygen diffusion from langasite into the growing layer and a decrease in the dislocation density in the main GaN layer upon its subsequent high-temperature deposition (~700°C). Further lowering of the growth temperature of the nucleation layer leads to sharp degradation of the GaN/LGS layer crystal quality. As a result of the performed research, an epitaxial GaN/LGS layer with a dislocation density of ~10{sup 11} cm{sup –2} and low surface roughness (<2 nm) is obtained.

36 MATERIALS SCIENCE↗

Shaped silicon wafers obtained by hot plastic deformation: performance evaluation for future astronomical x-ray telescopes

In order to develop lightweight and high angular resolution x-ray mirrors, we have investigated hot plastic deformation of 4 in. silicon (111) wafers. A sample wafer was deformed using hemispherical dies with a curvature radius of 1000 mm. The measured radius of the deformed wafer was 1030 mm, suggesting that further conditioning is indispensable for better shaping. For the first time to our knowledge, x-ray reflection on a deformed wafer was detected at Al K{alpha} 1.49 keV. An estimated surface roughness of <1 nm from the x-ray reflection profile was comparable to that of a bare silicon wafer without deformation. Hence, no significant degradation of the microroughness was seen.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Rolling Process Modeling Report. Finite-Element Model Validation and Parametric Study on various Rolling Process parameters

Pacific Northwest National Laboratory (PNNL) has been investigating manufacturing processes for the uranium-10% molybdenum alloy plate-type fuel for high-performance research reactors in the United States. This work supports the U.S. Department of Energy National Nuclear Security Administration’s Office of Material Management and Minimization Reactor Conversion Program. This report documents modeling results of PNNL’s efforts to perform finite-element simulations to predict roll-separating forces for various rolling mill geometries for PNNL, Babcock & Wilcox Co., Y-12 National Security Complex, Los Alamos National Laboratory, and Idaho National Laboratory. The model developed and presented in a previous report has been subjected to further validation study using new sets of experimental data generated from a rolling mill at PNNL. Simulation results of both hot rolling and cold rolling of uranium-10% molybdenum coupons have been compared with experimental results. The model was used to predict roll-separating forces at different temperatures and reductions for five rolling mills within the National Nuclear Security Administration Fuel Fabrication Capability project. This report also presents initial results of a finite-element model microstructure-based approach to study the surface roughness at the interface between zirconium and uranium-10% molybdenum.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The Effect of Adsorbed Volatile Organic Compounds on an Ultrathin Water Film Measurement

Using surface plasmon resonance imaging (SPRi), we have recently shown for the first time the existence of a monolayer water film between droplets during dropwise condensation. This study examines the effect of adsorbed volatile organic compounds (VOCs) on the ultrathin film measurement using SPRi. Further, the work presents the proper surface-treatment process that enables measurements of the ultrathin water layer during high-speed imaging of dropwise condensation at 3000 frame per second. In this study, two methods were applied for cleaning the surface (gold-coated glass)—(1) standard cleaning procedure (SCP) using acetone, isopropyl alcohol, and deionized water and (2) SCP followed by air plasma cleaning. This work discusses the effect of the cleaning procedures on surface roughness, contact angle, and surface chemistry using atomic force microscopy, optical microscopy, and an X-ray photoelectron spectroscope meter. The results showed that SCP before the SPRi is a proper surface-treatment method. The effect of adsorbed VOCs during dropwise condensation on a surface treated with SCP was measured to be 0.0025 (reflectivity unit), which was 70% smaller than the reflectance associated with a monolayer water film. The results of this work confirm a monolayer water film observation during the dropwise condensation, which has been reported before.

36 MATERIALS SCIENCE↗

Determination of Size, Albedo, and Thermal Inertia of 10 Vesta Family Asteroids with WISE/NEOWISE Observations

In this work, we investigate the size, thermal inertia, surface roughness, and geometric albedo of 10 Vesta family asteroids using the Advanced Thermophysical Model, based on the thermal-infrared data acquired by mainly NASA’s Wide-field Infrared Survey Explorer. Here, we show that the average thermal inertia and geometric albedo of the investigated Vesta family members are 42 J m{sup −2} s{sup −1/2} K{sup −1} and 0.314, respectively, where the derived effective diameters are less than 10 km. Moreover, the family members have a relatively low roughness fraction on their surfaces. The similarity in thermal inertia and geometric albedo among the V-type Vesta family members may reveal their close connection in origin and evolution. As the fragments of the cratering event of Vesta, the family members may have undergone a similar evolutionary process, thereby leading to very close thermal properties. Finally, we estimate their regolith grain sizes with different volume filling factors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Passive microwave studies

The application of passive microwave techniques from airborne and surface platforms for oceanography measurements is discussed. The program is designed to determine: (1) the optimum system parameters, (2) measurement techniques, and (3) the physical phenomena to enable unambiguous all-weather determination of the sea surface properties of sea roughness, surface wind fields, temperature, salinity, sea ice, and pollution. The advantages and disadvantages of the airborne and fixed station operations are examined.

Hollinger, J. P.↗

A model of wind shear and turbulence in the surface boundary layer

A model of wind and turbulence has been described for the surface boundary layer. The wind structure in the surface layer is considered to be a function of the surface parameters, stability, and height. The surface parameters considered are: (1) the surface roughness length; (2) the surface friction velocity; and (3) the zero plane displacement height. The stability parameter, Z/L, where L is the Monin-Obukov stability length, describes the thermal effect on the wind profile. The logarithmic wind profile is used to describe the mean wind field in the neutral boundary layer, and a logarithmic profile with a stability defect is used to describe the stable and unstable atmospheric conditions. For the very stable conditions, the logarithmic wind law does not hold. Under this condition, the layers of the atmosphere become disconnected and large scale frontal motions are the predominate factor in defining the wind profile. Figures are presented which represent some typical wind profiles in the very stable condition.

Luers, J. K.↗

Detecting Cracks in Rough Metal Surfaces

Test based on eddy-current probe technique identifies cracks in swaged metals. Hinged collar with spring-loaded latch holds probe in place on part tested. For repeated measurements on same or similar parts, collar loosened and moved to various measuring positions. Method suitable for many kinds of metal parts, including swaged fittings, tubing, and pipes. Used for rapid crack/no-crack determinations in suspect parts already installed.

Zuver, N. T.↗

Photometry of rough planetary surfaces - The role of multiple scattering

Topographic features affect the scattering properties of planetary surfaces by casting shadows and altering the local incidence and emission angles. Measurements of this phenomenon were obtained on the Cornell goniometer for both high and low albedo surfaces. For the low albedo surface, the decrease in reflected radiation due to topography increases sharply with increasing phase angle, whereas for the high albedo sample the effects are approximately constant between phase angles of 30 and 70 deg. The observations are in good agreement with a theoretical model in the case of the dark surface. However, for the high albedo surface the model overestimates the effects by a factor of 2, since it does not include the partial illumination of shadows by multiple scattering. For both high and low albedo surfaces, the effects of topography do not become significant until a phase angle of 30-40 deg.

Buratti, B. J.↗

Effect of abrasive grit size on wear of manganese-zinc ferrite under three-body abrasion

Wear experiments were conducted using replication electron microscopy and reflection electron diffraction to study abrasion and deformed layers produced in single-crystal Mn-Zn ferrites under three-body abrasion. The abrasion mechanism of Mn-Zn ferrite changes drastically with the size of abrasive grits. With 15-micron (1000-mesh) SiC grits, abrasion of Mn-Zn ferrite is due principally to brittle fracture; while with 4- and 2-micron (4000- and 6000-mesh) SiC grits, abrasion is due to plastic deformation and fracture. Both microcracking and plastic flow produce polycrystalline states on the wear surfaces of single-crystal Mn-Zn ferrites. Coefficient of wear, total thickness of the deformed layers, and surface roughness of the wear surfaces increase markedly with an increase in abrasive grit size. The total thicknesses of the deformed layers are 3 microns for the ferrite abraded by 15-micron SiC, 0.9 microns for the ferrite abraded by 4-micron SiC, and 0.8 microns for the ferrite abraded by 1-micron SiC.

Miyoshi, Kazuhisa↗

Wetting Hysteresis at the Molecular Scale

The motion of a fluid-fluid-solid contact line on a rough surface is well known to display hysteresis in the contact angle vs. velocity relationship. In order to understand the phenomenon at a fundamental microscopic level, we have conducted molecular dynamics computer simulations of a Wilhelmy plate experiment in which a solid surface is dipped into a liquid bath, and the force-velocity characteristics are measured. We directly observe a systematic variation of force and contact angle with velocity, which is single-valued for the case of an atomically smooth solid surface. In the microscopically rough case, however, we find (as intuitively expected) an open hysteresis loop. Further characterization of the interface dynamics is in progress.

Jin, Wei↗

Surface Morphology of Undoped and Doped ZnSe Films

Rare-earth doped ions in polar II-VI semiconductors have recently played an important role in the optical properties of materials and devices. In this study, undoped ZnSe and erbium doped ZnSe films were grown by radio frequency (RF) magnetron sputtering method. Atomic Force Microscopy (AFM) was used together with optical microscopy and UV-Vis spectroscopy to characterize the films. Doped samples were found to have higher surface roughness and quite different surface morphology compared to that of undoped samples. The grown films generally show a relatively smooth and uniform surface indicating that they are of overall good quality. The impact of plasma etching on ZnSe:Er film examined under AFM is also discussed.

George, T.↗

Fabrication Method for LOBSTER-Eye Optics in <110> Silicon

Soft x-ray optics can use narrow slots to direct x-rays into a desirable pattern on a focal plane. While square-pack, square-pore, slumped optics exist for this purpose, they are costly. Silicon (Si) is being examined as a possible low-cost replacement. A fabrication method was developed for narrow slots in <110> Si demonstrating the feasibility of stacked slot optics to replace micropores. Current micropore optics exist that have 20-micron-square pores on 26-micron pitch in glass with a depth of 1 mm and an extent of several square centimeters. Among several proposals to emulate the square pore optics are stacked slot chips with etched vertical slots. When the slots in the stack are positioned orthogonally to each other, the component will approach the soft x-ray focusing observed in the micropore optics. A specific improvement Si provides is that it can have narrower sidewalls between slots to permit greater throughput of x-rays through the optics. In general, Si can have more variation in slot geometry (width, length). Further, the sidewalls can be coated with high-Z materials to enhance reflection and potentially reduce the surface roughness of the reflecting surface. Narrow, close-packed deep slots in <110> Si have been produced using potassium hydroxide (KOH) etching and a patterned silicon nitride (SiN) mask. The achieved slot geometries have sufficient wall smoothness, as observed through scanning electron microscope (SEM) imaging, to enable evaluation of these slot plates as an optical element for soft x-rays. Etches of different angles to the crystal plane of Si were evaluated to identify a specific range of etch angles that will enable low undercut slots in the Si <110> material. These slots with the narrow sidewalls are demonstrated to several hundred microns in depth, and a technical path to 500-micron deep slots in a precision geometry of narrow, closepacked slots is feasible. Although intrinsic stress in ultrathin wall Si is observed, slots with walls approaching 1.5 microns can be achieved (a significant improvement over the 6-micron walls in micro - pore optics). The major advantages of this technique are the potential for higher x-ray throughout (due to narrow slot walls) and lower cost over the existing slumped micropore glass plates. KOH etching of smooth sidewalls has been demonstrated for many applications, suggesting its feasibility for implementation in x-ray optics. Si cannot be slumped like the micropore optics, so the focusing will be achieved with millimeter-scale slot plates that populate a spherical dome. The possibility for large-scale production exists for Si parts that is more difficult to achieve in micropore parts.

Chervenak, James↗

Regional Impacts of Ice Sheet Surface Representation Improvements in an Earth System Model

Ice sheet surface conditions and their subsequent impact on surface mass balance play an important role in ice sheet dynamics and ice sheet interaction with the overlying atmosphere and surrounding ocean. The NASA Global Modeling and Assimilation Office’s (GMAO) Goddard Earth Observing System (GEOS) ecosystem of models and reanalyses model ice sheet and glacier surface mass balance with a moderately complex snow and ice module, including prognostic surface albedo evolution, fractional snow cover, and snowpack hydrology and meltwater retention. With this configuration, Greenland near surface air temperatures and ice sheet melt are well represented in MERRA-2, GMAO’s current atmospheric reanalysis; however, the similarity to observations in some regions is due, in part, to compensating biases in surface energy budget. Recent improvements to GEOS’ cloud microphysics and longwave radiation parameterizations reduced biases in surface net longwave radiation and exacerbated surface net shortwave radiation biases, effectively increasing near surface temperatures and melting, particularly during the summer months. Here, we demonstrate the Earth system response to an improved representation of the ice sheet surface focused on minimizing the surface energy biases and increasing spatial and temporal representativeness. New changes to the surface albedo parameterization, including the introduction of a prognostic aerosol darkening scheme, help mitigate shortwave biases, while modifications to surface roughness characteristics improve near surface sensible heat fluxes. Focusing on the Arctic and Greenland, we examine the combined impact on these changes on regional weather conditions and ice sheet surface mass balance using a high resolution atmospheric only experiment, and we use a coupled model configuration to assess the impact on oceanic conditions and subseasonal-to-seasonal prediction. Overall, these improvements increase modeled ice sheet surface realism and provide a strong basis for more accurate ice sheet mass balance in GMAO’s future reanalyses and forecasting systems.

Lauren C Andrews↗

Regional Impacts of Ice Sheet Surface Representation Improvements in an Earth System Model

Ice sheet surface conditions and their subsequent impact on surface mass balance play an important role in ice sheet dynamics and ice sheet interaction with the overlying atmosphere and surrounding ocean. The NASA Global Modeling and Assimilation Office’s (GMAO) Goddard Earth Observing System (GEOS) ecosystem of models and reanalyses model ice sheet and glacier surface mass balance with a moderately complex snow and ice module, including prognostic surface albedo evolution, fractional snow cover, and snowpack hydrology and meltwater retention. With this configuration, Greenland near surface air temperatures and ice sheet melt are well represented in MERRA-2, GMAO’s current atmospheric reanalysis; however, the similarity to observations in some regions is due, in part, to compensating biases in surface energy budget. Recent improvements to GEOS’ cloud microphysics and longwave radiation parameterizations reduced biases in surface net longwave radiation and exacerbated surface net shortwave radiation biases, effectively increasing near surface temperatures and melting, particularly during the summer months. Here, we demonstrate the Earth system response to an improved representation of the ice sheet surface focused on minimizing the surface energy biases and increasing spatial and temporal representativeness. New changes to the surface albedo parameterization, including the introduction of a prognostic aerosol darkening scheme, help mitigate shortwave biases, while modifications to surface roughness characteristics improve near surface sensible heat fluxes. Focusing on the Arctic and Greenland, we examine the combined impact on these changes on regional weather conditions and ice sheet surface mass balance using a high resolution atmospheric only experiment, and we use a coupled model configuration to assess the impact on oceanic conditions and subseasonal-to-seasonal prediction. Overall, these improvements increase modeled ice sheet surface realism and provide a strong basis for more accurate ice sheet mass balance in GMAO’s future reanalyses and forecasting systems.

Lauren C. Andrews↗

Determination of thermal accommodation coefficients from heat transfer measurements between parallel plates.

Thermal accommodation coefficients have been derived for a variety of gas-surface combinations using an experimental apparatus developed to measure the pressure dependence of the conductive heat flux between parallel plates at unequal temperature separated by a gas-filled gap. The heat flux is inferred from temperature-difference measurements across the plates in a configuration where the plate temperatures are set with two carefully controlled thermal baths. Temperature-controlled shrouds provide for environmental isolation of the opposing test plates. Since the measured temperature differences in these experiments are very small (typically 0.3 C or less over the entire pressure range), high-precision thermistors are used to acquire the requisite temperature data. High-precision components have also been utilized on the other control and measurement subsystems in this apparatus, including system pressure, gas flow rate, plate alignment, and plate positions. The apparatus also includes the capability for in situ plasma cleaning of the installed test plates. Measured heat-flux results are used in a formula based on Direct Simulation Monte Carlo (DSMC) code calculations to determine the thermal accommodation coefficients. Thermal accommodation coefficients have been determined for three different gases (argon, nitrogen, helium) in contact with various surfaces. Materials include metals and alloys such as aluminum, gold, platinum, and 304 stainless steel. A number of materials important to fabrication of Micro Electro Mechanical Systems (MEMS) devices have also been examined. For most surfaces, coefficient values are near 0.95, 0.85, and 0.45 for argon, nitrogen, and helium, respectively. Only slight differences in accommodation as a function of surface roughness have been seen. Surface contamination appears to have a more significant effect: argon plasma treatment has been observed to reduce thermal accommodation by as much as 0.10 for helium. Mixtures of argon and helium have also been examined, and the results have been compared to DSMC simulations incorporating thermal-accommodation values from single-species experiments.

36 MATERIALS SCIENCE↗

Assessing the Effects of Various Surface Textures and Features on Turbulent Heat Transfer in Hypersonic Flight

Experiments were conducted in the NASA Ames Hypervelocity Free Flight Aerodynamic Facility (ballistic range) to quantify the effects on turbulent convective heat transfer of distributed surface roughness, and of isolated features, representative of thermal protection systems on atmospheric entry vehicles. The surface textures and features were applied on the conic frusta of 45o sphere-cone models having a nose-to-base radius ratio of 0.5, similar to the forebody geometry of the Galileo and Pioneer-Venus entry probes. Test conditions were selected to provide turbulent roughness Reynolds numbers, k+, in the ranges expected for outer planet entry missions. Turbulent flow on the conic frustum was achieved by tripping the flow on the sphere-segment nose cap with distributed surface roughness, created by sand-blasting the nose cap. Surface textures included distributed, acreage, roughness, as well as cavity and groove discrete features. The majority of the data to be presented are results for distributed roughness, which includes both random, sand-grain-like roughness, and regular pattern roughness. The pattern roughness was designed to represent the roughness on woven thermal protection system materials, such as NASA’s 3-D Medium Density Carbon Phenolic (3MDCP), also known as HEEET, developed by the Heatshield for Extreme Entry Environments Technology project. The pattern roughness tested is a 3-D wavy surface, and includes three different roughness element height-to-spacing ratios representative of two configurations of 3MDCP, and spanning ratios measured both before, and after, ablation in an arc jet test facility. The patterns tested in the ballistic range were laser-etched on metal models, and represented an idealized version of the real-world materials in which each roughness element was nearly identical. Additional tests were performed wherein the laser-etched patterns were degraded by sand-blasting with various sized grit media, to produce regular patterns with superimposed irregular roughness, more representative of flight materials. Results of each will be compared. The discrete features tested included cylindrical cavities and rectangular grooves of various width-to-depth ratios. Cavities represent either heatshield damage, such as from micro-meteoroid and orbital debris (MMOD) damage, or from designed penetrations, such as on the Genesis sample return capsule. The grooves were scaled representations of seams between segments of HEEET material in a notional tiled thermal protection system. The tests examined the effects on turbulent heating downstream of the isolated features. The tests were conducted at speeds between 3 km/s and 4 km/s in air between 0.15 atm and 0.25 atm (Mach numbers between 9 and 12). Roughness Reynolds numbers, k+, ranged from 12 to 70 for the sand roughness, and as high as 200 for the pattern roughness. Boundary-layer parameters required for calculating k+ were evaluated using computational fluid dynamics simulations using the DPLR (Data Parallel Line Relaxation) code. Each model included both rough- and smooth-wall segments, and heat transfer augmentation factors were determined as the ratio of the rough-wall to smooth-wall heat flux measured on each test.

hypersonic↗