Search NASA⌕ Search

SEARCH · Search NASA

Results for “source injection”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,225 records · Page 68

Exhaust particle characterization for lean and stoichiometric DI vehicles operating on ethanol-gasoline blends

Gasoline direct injection (GDI) engines can offer better fuel economy and higher performance over their port fuel-injected (PFI) counterparts, and are now appearing in increasingly more U.S. and European vehicles. Small displacement, turbocharged GDI engines are replacing large displacement engines, particularly in light-duty trucks and sport utility vehicles, in order for manufacturers to meet the U.S. fuel economy standards for 2016. Furthermore, lean-burn GDI engines can offer even higher fuel economy than stoichiometric GDI engines and have overcome challenges associated with cost-effective aftertreatment for NOx control. Along with changes in gasoline engine technology, fuel composition may increase in ethanol content beyond the current 10% due to the recent EPA waiver allowing 15% ethanol. In addition, the Renewable Fuels Standard passed as part of the 2007 Energy Independence and Security Act (EISA) mandates the use of biofuels in upcoming years. GDI engines are of environmental concern due to their high particulate matter (PM) emissions relative to port-fuel injected (PFI) gasoline vehicles; widespread market penetration of GDI vehicles may result in additional PM from mobile sources at a time when the diesel contribution is declining. In this study, we characterized particulate emissions from a European certified lean-burn GDI vehicle operating on ethanol-gasoline blends. Particle mass and particle number concentration emissions were measured for the Federal Test Procedure urban driving cycle (FTP 75) and the more aggressive US06 driving cycle. Particle number-size distributions and organic to elemental carbon ratios (OC/EC) were measured for 30 MPH and 80 MPH steady-state operation. In addition, particle number concentration was measured during wide open throttle accelerations (WOTs) and gradual accelerations representative of the FTP 75. Fuels included certification gasoline and 10% (E10) and 20% (E20) ethanol blends from the same supplier. The particle mass emissions were approximately 3 and 7 mg/mile for the FTP75 and US06, respectively, with lower emissions for the ethanol blends. The data are compared to a previous study on a U.S.-legal stoichiometric GDI vehicle operating on the same ethanol blends. The lean-burn GDI vehicle emitted a higher number of particles, but had an overall smaller average size. Particle number per mile decreased with increasing ethanol content for the transient tests. For the 30 and 80 mph tests, particle number concentration decreased with increasing ethanol content, although the shape of the particle size distribution remained the same. Engine-out OC/EC ratios were highest for the stoichiometric GDI vehicle with E20, but tailpipe OC/EC ratios were similar for all vehicles.

02 PETROLEUM↗

The E166 experiment: Development of an Undulator-Based Polarized Positron Source for the International Linear Collider

A longitudinal polarized positron beam is foreseen for the international linear collider (ILC). A proof-of-principle experiment has been performed in the final focus test beam at SLAC to demonstrate the production of polarized positrons for implementation at the ILC. The E166 experiment uses a 1 m long helical undulator in a 46.6 GeV electron beam to produce a few MeV photons with a high degree of circular polarization. These photons are then converted in a thin target to generate longitudinally polarized e{sup +} and e{sup -}. The positron polarization is measured using a Compton transmission polarimeter. The data analysis has shown asymmetries in the expected vicinity of 3.4% and {approx}1% for photons and positrons respectively and the expected positron longitudinal polarization is covering a range from 50% to 90%. The full exploitation of the physics potential of an international linear collider (ILC) will require the development of polarized positron beams. Having both e{sup +} and e{sup -} beams polarized will provide new insight into structures of couplings and thus give access to physics beyond the standard model [1]. The concept for a polarized positron source is based on circularly polarized photon sources. These photons are then converted to longitudinally polarized e{sup +} and e{sup -} pairs. While in an experiment at KEK [1a], Compton backscattering is used [2], the E166 experiment uses a helical undulator to produce polarized photons. An undulator-based positron source for the ILC has been proposed in [3,4]. The proposed scheme for an ILC positron source is illustrated in figure 1. In this scheme, a 150 GeV electron beam passes through a 120 m long helical undulator to produce an intense photon beam with a high degree of circular polarization. These photons are converted in a thin target to e{sup +} e{sup -} pairs. The polarized positrons are then collected, pre-accelerated to the damping ring and injected to the main linac. The E166 experiment is dedicated to test this concept of a helical-undulator-based polarized positron source for the ILC. The experiment was carried out at SLAC where it benefitted from the high quality electron beam in the final focus test beam (FFTB).

43 PARTICLE ACCELERATORS↗

Location of Maximum Credible Beam Losses in LCLS Injector

The memo describes the maximum credible beam the LCLS injector can produce and lose at various locations along the beamline. The estimation procedure is based upon three previous reports [1, 2, 3]. While specific numbers have been updated to accurately reflect the present design parameters, the conclusions are very similar to those given in Ref 1. The source of the maximum credible beam results from the explosive electron emission from the photocathode if the drive laser intensity exceeds the threshold for plasma production. In this event, the gun's RF field can extract a large number of electrons from this plasma which are accelerated out of the gun and into the beamline. This electron emission persists until it has depleted the gun of all its energy. Hence the number of electrons emitted per pulse is limited by the amount of stored RF energy in the gun. It needs to be emphasized that this type of emission is highly undesirable, as it causes permanent damage to the cathode.

43 PARTICLE ACCELERATORS↗

High Brightness and High Polarization Electron Source for Spin-LEEM

A point-like emission mechanism is required for a GaAs polarized electron source to produce an electron beam with high brightness. This is realized by changing the direction of injection laser from a front-side to a back-side of the photocathode. Based on this concept, a 20 keV gun (JPES-1) was constructed and a transmission photocathode including an active layer of a GaAs-GaAsP superlattice was installed. It produced a laser spot diameter as small as 1.3 {mu}m for the 760{approx}810 nm laser wavelength, and the brightness of {approx}2x10{sup 7} A{center_dot}cm{sup -2}{center_dot}sr{sup -1} corresponding to a reduced brightness of {approx}1.0x10{sup 7} A{center_dot}cm{sup -2}{center_dot}sr{sup -1}{center_dot}V{sup -1} was obtained for an extracted current of 5.3 {mu}A. This brightness is still smaller than those of W-field-emitters, but one order of magnitude higher than those of LaB{sub 6} emitters. The peak polarization of {approx}90% was achieved at the same time by the photocathode which has an inserted GaAs thin layer between the GaAsP substrate and the GaAaP buffer layer. It demonstrated that the strain-control of the GaAsP buffer layer is indispensable to achieve the highest polarization. The charge density lifetime of 1.8x10{sup 8} C/cm{sup 2} was observed for an extracted current of {approx}3 {mu}A. The second gun system (JPES-2) was already constructed and mounted to a LEEM apparatus operated at OECU.

43 PARTICLE ACCELERATORS↗

Ion source development for a photoneutralization based NBI system for fusion reactors

The next step after ITER is to demonstrate the viability and generation of electricity by a future fusion reactor (DEMO). The specifications required to operate an NBI system on DEMO are very demanding. The system has to provide a very high level of power and energy, ~100MW of D° beam at 1MeV, including high wall-plug efficiency (η > 60%). For this purpose, a new injector concept, called Siphore, is under investigation between CEA and French universities. Siphore is based on the stripping of the accelerated negative ions by photo-detachment provided by several Fabry-Perot cavities (3.5MW of light power per cavity) implemented along the D{sup −} beam. The beamline is designed to be tall and narrow in order that the photon flux overlaps the entire negative ion beam. The paper will describe the present R and D at CEA which addresses the development of an ion source and pre-accelerator prototypes for Siphore, the main goal being to produce an intense negative ion beam sheet. The negative ion source Cybele is based on a magnetized plasma column where hot electrons are emitted from the source center. Parametric studies of the source are performed using Langmuir probes in order to characterize the plasma and to compare with numerical models being developed in French universities.

43 PARTICLE ACCELERATORS↗

Investigation of the adhesive bonding technology for the insulator structure of EAST neutral beam injector

A key issue on the development of EAST ion source was the junction design of insulator structure, which consists of three insulators and four supporting flanges of electrode grid. Because the ion source is installed on the vertical plane, the insulator structure has to withstand large bending and shear stress due to the gravity of whole ion source. Through a mechanical analysis, it was calculated that the maximum bending normal stress was 0.34 MPa and shear stress was 0.23 MPa on the insulator structure. Due to the advantages of simplicity and high strength, the adhesive bonding technology was applied to the junction of insulator structure. A tensile testing campaign of different junction designs between insulator and supporting flange was performed, and a junction design of stainless steel and fiber enhanced epoxy resin with epoxy adhesive was determined. The insulator structure based on the determined design can satisfy both the requirements of high-voltage holding and mechanical strength.

42 ENGINEERING↗

On the role of electron energy distribution function in double frequency heating of electron cyclotron resonance ion source plasmas

Double frequency heating (DFH) is a tool to improve the output of highly charged ions particularly from modern electron cyclotron resonance ion source installations with very high RF-frequencies. In order to gain information on the DFH-mechanism and on the role of the lower injected frequency we have carried out a series of dedicated experiments where we have put emphasis on the creation of a discrete resonance surface also for this lower frequency. Our well-established method of inserting an emissive MD (metal-dielectric) liner into the plasma chamber of the source is used in these experiments as a tool of investigation. In this way, the electron temperature and density for both ECR zones is increased in a controlled manner, allowing conclusions on the role of the change of the electron-energy-distribution function with and without DFH.

43 PARTICLE ACCELERATORS↗

Projections of global mercury emissions in 2050.

Global Hg emissions are presented for the year 2050 under a variety of assumptions about socioeconomic and technology development. We find it likely that Hg emissions will increase in the future. The range of 2050 global Hg emissions is projected to be 2390-4860 Mg, compared to 2006 levels of 2480 Mg, reflecting a change of -4% to +96%. The main driving force for increased emissions is the expansion of coal-fired electricity generation in the developing world, particularly Asia. Our ability to arrest the growth in Hg emissions is limited by the relatively low Hg removal efficiency of the current generation of emission control technologies for coal-fired power plants (flue-gas desulfurization). Large-scale deployment of advanced Hg sorbent technologies, such as Activated Carbon Injection, offers the promise of lowering the 2050 emissions range to 1670-3480 Mg, but these technologies are not yet in commercial use. The share of elemental Hg in total emissions will decline from today's levels of {approx}65% to {approx}50-55% by 2050, while the share of divalent Hg will increase. This signals a shift from long-range transport of elemental Hg to local deposition of Hg compounds though emissions of both species could increase under the worst case.

54 ENVIRONMENTAL SCIENCES↗

Seismic monitoring of CO 2 geosequestration using multi-well 4D DAS VSP: Stage 3 of the CO2CRC Otway project

An important part of any CO 2 geosequestration project is to ensure CO 2 containment and conformance in the subsurface. This is generally done by implementing a comprehensive, risk-based Measurement, Monitoring and Verification plan, a key element of which is active time-lapse seismic monitoring. However, high cost and environmental impact of the standard surface seismic monitoring dictate the need for a cost-effective and environmentally friendly alternative. An opportunity to develop such method emerges with advances in distributed acoustic sensing (DAS) technology, which turns an optical fibre into a seismic sensor with dense spatial sampling. DAS can be permanently deployed in multiple wells across the geosequestration site providing a robust and non-intrusive network of seismic receivers. This approach was developed and tested in the CO2CRC Otway project, where injection of 15 kt of CO 2 at 1.5 km depth was monitored with a 4D vertical seismic profiling (VSP) using five borehole DAS arrays and mobile vibroseis sources. The 4D DAS VSP in each of the five wells provides broadly consistent images of the CO 2 plume with some differences due to different illumination of the target horizon, lateral variation of velocities, and seismic anisotropy. When the newly injected CO 2 reaches a CO 2 plume created as a result of an earlier injection into the same formation ~600 m updip, 4D DAS VSP shows a change in reflectivity in that area and beyond. Furthermore, this shows a potential of 4D DAS VSP for monitoring gas injection into gas-saturated reservoirs.

58 GEOSCIENCES↗

Stellar Evolutionary Effects on the Abundance of PAHS and SN-Condensed Dust in Galaxies

Spectral aid photometric observations of nearby galaxies show a correlation between the strength of their mid-IR aromatic features and their metal abundance, and a deficiency of these features in low-metallicity galaxies. The aromatic features are most commonly attributed to emission from PAH molecules. In this paper, we suggest that the observed correlation represents a trend of PAH abundance with galactic age, reflecting the delayed injection of PAHs and carbon dust into the ISM, by AGB stars in their final, post-AGB phase of their evolution. These AGB stars are the primary sources of PAHs and carbon dust in galaxies, and recycle their ejecta back to the interstellar medium only after a few hundred million years of evolution on the main sequence. In contrast, more massive stars that explode as Type II supernovae inject their metals and dust almost instantaneously after their formation. After determining the PAH abundances in 35 nearby galaxies, we use a chemical evolution model to show that the delayed injection of carbon dust by AGB stars provides a natural explanation to the dependence of the PAH content, in galaxies with metallicity. We also show that larger dust particles giving rise to the far-IR emission follow a distinct evolutionary trend closely related to the injection of dust by massive stars into the ISM.

Dwek, Eli↗

Status and specifications of a Project X front-end accelerator test facility at Fermilab

This paper describes the construction and operational status of an accelerator test facility for Project X. The purpose of this facility is for Project X component development activities that benefit from beam tests and any development activities that require 325 MHz or 650 MHz RF power. It presently includes an H- beam line, a 325 MHz superconducting cavity test facility, a 325 MHz (pulsed) RF power source, and a 650 MHz (CW) RF power source. The paper also discusses some specific Project X components that will be tested in the facility. Fermilab's future involves new facilities to advance the intensity frontier. In the early 2000's, the vision was a pulsed, superconducting, 8 GeV linac capable of injecting directly into the Fermilab Main Injector. Prototyping the front-end of such a machine started in 2005 under a program named the High Intensity Neutrino Source (HINS). While the HINS test facility was being constructed, the concept of a new, more versatile accelerator for the intensity frontier, now called Project X, was forming. This accelerator comprises a 3 GeV CW superconducting linac with an associated experimental program, followed by a pulsed 8 GeV superconducting linac to feed the Main Injector synchrotron. The CW Project X design is now the model for Fermilab's future intensity frontier program. Although CW operation is incompatible with the original HINS front-end design, the installation remains useful for development and testing many Project X components.

43 PARTICLE ACCELERATORS↗

Optimal carbon capture and storage contracts using historical CO 2 emissions levels

In an effort to reduce carbon dioxide (CO 2 ) emissions to the atmosphere, carbon capture and storage (CCS) technology has been developed to collect CO 2 from emissions generators and store it underground. Recent proposed legislation would limit the volume of emissions generated from power sources, effectively requiring some sources to participate in CCS. Both emissions sources and storage operators require incentives to enter into contracts to capture excess emissions at the source, and transport and store the CO 2 underground. As the level of emissions from power plants is stochastic and carryover into future time periods is expensive, we develop a newsvendor model to determine the optimal price and volume of these contracts to maximize the expected profit of the storage operator and encourage the participation of multiple emissions sources. Because the storage operator has a limit on the amount of CO 2 that can be injected each month, this limit affects the allocation of the optimal contract amounts between the emitters. Furthermore, the distribution of emissions and relative costs of transportation also influence the optimal policy. In addition to analytical solutions, we present data-driven methods for using correlated emissions data to determine the optimal price and volume of these contracts.

42 ENGINEERING↗

Implosion dynamics in double planar wire array Z pinches

The double planar wire array (DPWA) Z pinch is a highly efficient radiation source with unique implosion dynamics and precursor formations. The inductively divided current successively ablates the wires and injects the material to the interior of the array. Three uniquely imploding DPWA load types were identified and classified according to the critical load parameter: low, intermediate, or high aspect ratio. Radiation pulse shaping was obtained from secondary precursors: off-axis mass carrying high current densities during the implosion phase. Time-gated EUV spectroscopy of off-axis mass accumulations is used to assess a 60 eV electron temperature prior to the implosion phase. These structures are shown to form by a different mechanism than the secondary precursors. High yields, compact size, and shaped radiation pulses merit further consideration of the DPWA as a candidate for inertial confinement fusion research.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Taylor limit studies for local helicity injection plasma startup

Solenoid-free tokamak startup techniques can simplify the design and reduce the cost of tokamak-based fusion energy systems. The newly commissioned Pegasus-III spherical tokamak provides a dedicated platform for developing a scalable solenoid-free startup approach. Local helicity injection (LHI) is one promising technique being developed on Pegasus-III, which uses compact edge current sources to drive open field line current I inj that is redistributed via helicity-conserving instabilities to initiate tokamak plasmas. These instabilities relax the system toward a minimum energy state described by Taylor relaxation theory. This relaxation process imposes a global current limit for LHI plasmas, referred to as the Taylor limit I TL ⁠, which can dictate the plasma current I p evolution. Experiments on Pegasus and Pegasus-III show that increasing this limit leads to more effective utilization of the available helicity input and higher I p plasmas. Initial Pegasus-III experiments have verified the expected I TL $\varpropto$ ( I inj B T ) 1/2 scaling holds for B T and I inj up to 0.3 T on axis and 12 kA ⁠, respectively. Additionally, data from different injector arrays show that the width of the injector aperture directly alters I TL and can be leveraged for future injector design optimization. Throughout these scaling studies, discharges were overdriven at I p = I TL by providing excess helicity input. Intermittent bursts of n = 1 magnetic activity consistent with large-scale reconnection events occurred more often as the system was increasingly overdriven leading to a flattening of the λ = μ 0 J ∥ / |B| profile, where J ∥ is the parallel current density.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

PROTON HEATING BY NONLINEAR FIELD-ALIGNED ALFVEN WAVES IN SOLAR CORONAL HOLES

Field-aligned Alfven waves are often viewed as a source of the proton heating that accelerates the fast solar wind. However, the energy that they can inject into the protons in the limit of cyclotron-resonant quasi-linear diffusion is insufficient to account for the observed acceleration. To test the validity of this limit in coronal holes, nonlinear Alfven waves are modeled using a hybrid code. It is found that the nonlinearity is particularly strong when the intensity of antisunward-propagating waves is comparable to that of sunward waves. The sunward waves can be generated by the proton distribution as it evolves with the heliocentric distance. The ponderomotive force and beat interaction are identified as the most important nonlinear effects. The nonlinearity of the field-aligned Alfven waves produces density fluctuations. In the simulations, the amplitude of the density fluctuations was kept within the observed constraints from the interplanetary scintillation measurements in the corona. In this case, the characteristic time of the proton heating is almost 2 orders of magnitude smaller than the solar wind expansion time. Therefore, it can contribute to the energization of the solar wind on the global scale. The nonlinear wave damping operating alone cannot be responsible for the energization because it only causes particle diffusion parallel to the magnetic field. However, it can relax the limitation on the perpendicular diffusion imposed by the cyclotron resonance condition. The nonlinear damping combined with the linear one can then inject the additional thermal energy needed to accelerate the solar wind.

99 GENERAL AND MISCELLANEOUS↗

Modeling of high harmonic fast wave scenarios for NSTX Upgrade

NSTX-Upgrade will operate with toroidal magnetic fields ( B T ) up to 1 T, nearly twice the value used in the experiments on NSTX, and the available neutral beam injection (NBI) power will be doubled. The doubling of B T while retaining the 30 MHz RF source frequency has moved the heating regime from the high harmonic fast wave (HHFW) regime used in NSTX to the mid harmonic fast wave regime. By making use of the full wave code AORSA (assuming a Maxwellian plasma), this work explores different HHFW scenarios for two possible antenna frequencies (30 and 60 MHz) and with and without NBI. Both frequencies have large electron absorption for large wave toroidal number particularly without NBI. With the presence of NBI, the fast ions absorption can be dominant in some scenarios. Therefore, a competition between electron and fast ion absorption is clearly apparent partially explaining why in previous NSTX HHFW experiments, a less efficient electron heating was observed. Moreover at the toroidal field of 1 T, a direct thermal ion damping might be possible under the condition when the ion temperature is larger than electron temperature. In general, the electron and ion absorption are found very sensitive to the ratio of electron and ion temperature. The impact of the hydrogen species is also studied showing that, for hydrogen concentration below 2%, the hydrogen absorption is not significant. However, a larger hydrogen concentration could open up new HHFW heating scenarios in NSTX-U. Launching at high toroidal wave number appears to be one way to significantly reduce the ion damping and in turn to obtain large electron damping in the core which can play an important role in the transport studies for NSTX-U. Lastly, an higher magnetic field could also playing a role in increasing the electron temperature and consequently the electron absorption. Indeed a magnetic field scan is also shown and discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Investigations of plasma response associated with resonant magnetic perturbation fields using perturbation method in KSTAR H-mode plasmas

Abstract The plasma response associated with the resonant magnetic perturbation (RMP) field was investigated using the small edge perturbations induced by a modulated supersonic molecular beam injection (SMBI) in KSTAR. The modulated SMBI provides a time-varying perturbation of the plasma density source in the region just inside the last closed flux surface and a modulated flow damping rate. Radial propagation of the toroidal rotation perturbation induced by SMBI from the q = 3 surface to the q = 2 surface was observed. Theoretical analysis using the general perturbed equilibrium code of the RMP intensity profiles of the RMP field is consistent with the phase profile of the toroidal rotation perturbation.

Physics↗