Search NASA⌕ Search

SEARCH · Search NASA

Results for “Cyclone”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69

Development of Cost Effective Oxy-Combustion Retrofitting for Coal-Fired Boilers

The overall objective of this project is to further develop the oxy-combustion technology for commercial retrofit in existing wall-fired and Cyclone boilers by 2012. To meet this goal, a research project was conducted that included pilot-scale testing and a full-scale engineering and economic analysis.

01 COAL, LIGNITE, AND PEAT↗

Fast Pyrolysis Oil Stabilization: An Integrated Catalytic and Membrane Approach for Improved Bio-oils. Final Report

This University of Massachusetts, Amherst project, "Fast Pyrolysis Oil Stabilization: An Integrated Catalytic and Membrane Approach for Improved Bio-oils" started on 1st February 2009 and finished on August 31st 2011. The project consisted following tasks: Task 1.0: Char Removal by Membrane Separation Technology The presence of char particles in the bio-oil causes problems in storage and end-use. Currently there is no well-established technology to remove char particles less than 10 micron in size. This study focused on the application of a liquid-phase microfiltration process to remove char particles from bio-oil down to slightly sub-micron levels. Tubular ceramic membranes of nominal pore sizes 0.5 and 0.8m were employed to carry out the microfiltration, which was conducted in the cross-flow mode at temperatures ranging from 38 to 45 C and at three different trans-membrane pressures varying from 1 to 3 bars. The results demonstrated the removal of the major quantity of char particles with a significant reduction in overall ash content of the bio-oil. The results clearly showed that the cake formation mechanism of fouling is predominant in this process. Task 2.0 Acid Removal by Membrane Separation Technology The feasibility of removing small organic acids from the aqueous fraction of fast pyrolysis bio-oils using nanofiltration (NF) and reverse osmosis (RO) membranes was studied. Experiments were carried out with a single solute solutions of acetic acid and glucose, binary solute solutions containing both acetic acid and glucose, and a model aqueous fraction of bio-oil (AFBO). Retention factors above 90% for glucose and below 0% for acetic acid were observed at feed pressures near 40 bar for single and binary solutions, so that their separation in the model AFBO was expected to be feasible. However, all of the membranes were irreversibly damaged when experiments were conducted with the model AFBO due to the presence of guaiacol in the feed solution. Experiments with model AFBO excluding guaiacol were also conducted. NF membranes showed retention factors of glucose greater than 80% and of acetic acid less than 15% when operated at transmembrane pressures near 60 bar. Task 3.0 Acid Removal by Catalytic Processing It was found that the TAN reduction in bio-oil was very difficult using low temperature hydrogenation in flow and batch reactors. Acetic acid is very resilient to hydrogenation and we could only achieve about 16% conversion for acetic acid. Although it was observed that acetic acid was not responsible for instability of aqueous fraction of bio-oil during ageing studies (described in task 5). The bimetallic catalyst PtRe/ceria-zirconia was found to be best catalyst because its ability to convert the acid functionality with low conversion to gas phase carbon. Hydrogenation of the whole bio-oil was carried out at 125°C, 1450 psi over Ru/C catalyst in a flow reactor. Again, negligible acetic acid conversion was obtained in low temperature hydrogenation. Hydrogenation experiments with whole bio-oil were difficult to perform because of difficulty to pumping the high viscosity oil and reactor clogging. Task 4.0 Acid Removal using Ion Exchange Resins DOWEX M43 resin was used to carry out the neutralization of bio-oil using a packed bed column. The pH of the bio-oil increased from 2.43 to 3.7. The GC analysis of the samples showed that acetic acid was removed from the bio-oil during the neutralization and recovered in the methanol washing. But it was concluded that process would not be economical at large scale as it is extremely difficult to regenerate the resin once the bio-oil is passed over it. Task 5.0 Characterization of Upgraded Bio-oils We investigated the viscosity, microstructure, and chemical composition of bio-oils prepared by a fast pyrolysis approach, upon aging these fuels at 90ºC for periods of several days. Our results suggest that the viscosity increase is not correlated with the acids or char present in the bio-oils. The viscosity increase is due to formation of high molecular weight polymeric species over time. Our work also suggests that hydrogenation of the samples is beneficial in eliminating the viscosity increase. Task 6.0 Commercialization Assessment Renewable Oil International LLC (ROI) was responsible for Task 6.0, Commercialization Assessment. As part of this effort ROI focused on methods to reduce char carryover in the vapor stream from the fast pyrolysis reactor and residence time of the vapor in the reactor. Changes were made in the bio-oil recovery methodology and a reactor sweep gas used to reduce vapor residence time. Cyclones were placed in the vapor stream to reduce char particulate carryover. Microfiltration of the bio-oil was also researched to remove char particulate from the bio-oil. The capital cost for these improvements would be less than 2% of the total plant capital cost.

09 BIOMASS FUELS↗

Manufacturing conversion for energy efficiency

The Flambeau River Papers Manufacturing Conversion for Energy Efficiency Project has identified the following goals and objectives: 1. A low pressure accumulator tank will be installed to capture low pressure gases for reuse. The estimated cost is $\$$2.1 million with an energy savings of $\$$500,000 annually or enough natural gas savings to heat 590 average Wisconsin homes. 2. Replace the steam turbine and upgrade Paper Machine #3, the largest of Flambeau River Papers machines, at a cost of $\$$6.265 million. The result will save enough natural gas to heat 141 average homes, or about $\$$1.2-million each year. 3. Install a new cyclonic and cell fracturing technology dryer to reduce moisture in both sludge and biomass wastes. The estimated cost of this task is $\$$1.5-million with an annual energy savings of $\$$700,000. It will also eliminate all coal burning at Flambeau River Papers (7,200 tons of coal annually).

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

ARM Cloud Aerosol Precipitation Experiment (ACAPEX) Science Plan

The western U.S. receives precipitation predominantly during the cold season when storms approach from the Pacific Ocean. The snowpack that accumulates during winter storms provides about 70-90% of water supply for the region. Understanding and modeling the fundamental processes that govern the large precipitation variability and extremes in the western U.S. is a critical test for the ability of climate models to predict the regional water cycle, including floods and droughts. Two elements of significant importance in predicting precipitation variability in the western U.S. are atmospheric rivers and aerosols. Atmospheric rivers (ARs) are narrow bands of enhanced water vapor associated with the warm sector of extratropical cyclones over the Pacific and Atlantic oceans. Because of the large lower-tropospheric water vapor content, strong atmospheric winds and neutral moist static stability, some ARs can produce heavy precipitation by orographic enhancement during landfall on the U.S. West Coast. While ARs are responsible for a large fraction of heavy precipitation in that region during winter, much of the rest of the orographic precipitation occurs in post-frontal clouds, which are typically quite shallow, with tops just high enough to pass the mountain barrier. Such clouds are inherently quite susceptible to aerosol effects on both warm rain and ice precipitation-forming processes.

Leung, L. R.↗

Controlled Environmental Agriculture and Energy Project

Task A: Heating Plant - To design/build a Heating Plant Building with associated heating components for heating the greenhouse and to house the biomass gasification system. The subtasks for this task was and Engineering Design, Procurement and Construction activities. Overall milestones for this task were one construction permit, a code review and stamped drawings, engineered building vendor supplied sealed drawings, and the actual erection of a 1250 sq.ft. building. Task B: Heating System - The activities for this task included the procurement of the heating boilers and all ancillary components. This also included the installation of all heating system components in the new building plus the existing greenhouse structure. The milestone for this task was for the ability to heat 2500 gallons of water to 80 degrees F. Task C: Organic Matter Automated Hopper - The activities involved in this task involved design/fabrication of an automated hopper to feed the biomass gasification system. We need to procure materials and the automated motion components, have the system installed and factory acceptance test of the system. The milestone is to be able to feed wood chips at a rate of 20 Kg/Hr. Task D: Imbert Gasification System - The activities involved in this include the design/build of the gasifier with all accompany ductwork, cyclones and feeding system. Also there is a modification to the scrubber assembly with an automated ash removal system. Lastly a modification to the exhaust/flair system is made to capture heat from this component. Milestone for this task was to be able to produce 15 CFM of SynGas. Task E: Generator Powered by SynGas - Procure two 20kW 4 pole generator heads for installation on the gasifier system. Modification of the fuel plenum manifold with adjustment to the fuel curves for maximum power and load points. Milestone for this task is the ability to run two fuels, either SynGas or propane. This continues with the following tasks: Controls Heating System; Controls Generators 20kW; Controls Gasification; Algae System; and Final Evaluation/Operation.

60 APPLIED LIFE SCIENCES↗

Large-scale Meteorological Organization of Extreme Weather Events: Final Technical Report

Although the occurrence of regional extreme weather events (EWEs) such as cold air outbreaks, heat waves, droughts and floods are known to be related to planetary climate modes (PCMs) such as the El-Nino Southern Oscillation or North Atlantic Oscillation, intermediate meteorological patterns (IMPs) such as jet stream blocking, cyclones, and high pressure systems are required to connect PCMs to EWEs. Our project has revealed a physical pathway for the interplay among EWEs, IMPs and PCMs. Under support of this award, we have characterized the behavior of IMPs that cause winter cold air outbreaks, extreme floods and warm season dry spells in the US. This includes formulating meteorological “fingerprints” for easily identifying IMPs. The research performed includes a parallel analysis of how well modern climate models are able to simulate IMP behavior. We have also developed a novel approach for characterizing PCM structures and identifying EWE-LMP-PCM linkages. We discovered that dry spells occurring during spring and summer over the US are affected by changes in the North Pacific Ocean temperature. We further revealed the physical origin of a critical jet stream pattern occurring over the North Pacific Ocean that provides a “bridge” between the water cycles of East Asia and North America, respectively. We developed an advanced diagnostic technique (called piecewise tendency diagnosis or PTD) to understand the physical causes for the IMP formation and EWE-LMP-PCM linkages.

54 ENVIRONMENTAL SCIENCES↗

Production of Medically Important Radionuclides 52 Mn and 90 Nb

Over the final reporting period of this project, we at MGH finalized our effort on Project 2: Production and Characterization of 90 Nb which, as per our previous report led us to an interesting application of mass spectrometry in radiometal chemistry. Overall, our research has developed parameters and procedures for delivering high 90 Nb for preclinical and translational applications by initializing the cyclotron targetry and separation chemistry for delivering 90 Nb in a chemical form suitable for subsequent development of 90 Nb-based PET radiotracers, and most recently we have published on the mass spectrometry applications described in the present report. We have been working with MSKCC (PI Jason Lewis) on the 90 Nb methodology and have had input from UAB (PI Suzy Lapi). An in-person meeting was held during the upcoming funding period with 2 PIs who are co-organizing the Radiochemistry Symposium (Lapi and Vasdev) and Program Director Dr. Ethan Balkin, during the ACS National Meeting in March 2018, and 2 PIs (Lewis and Vasdev) co presented in at the World Federation of Nuclear Medicine and Biology at a symposium sponsored by the Australian Nuclear Sciences and Technology Organisation, where they are both collaborating, in Melbourne, Australia in April 2018. Future projects and collaborations are under discussion with the Lapi lab to focus on new applications of 76 Br chemistry, and a new collaboration has already resulted with the Lewis lab on 18 F radiochemistry that employ iodonium ylide based precursors developed in the Vasdev lab, for clinical production of [ 18 F]MFBG. It is noteworthy that the PI has now relocated to the University of Toronto and has 2 cyclotrons (IBA Cyclone and Scanditronix MC-17) that will also be used to explore new 11 C-radiochemistry including [ 11 C]CO.

07 ISOTOPE AND RADIATION SOURCES↗

Reliability, Resilience and the Oncoming Wave of Retiring Baseload Units, Volume I: The Critical Role of Thermal Units During Extreme Weather Events

This study examines the cold weather event now known as the Bomb Cyclone that blanketed much of the eastern half of the United States from Dec 27, 2017 through Jan 8, 2018. Analyses focus on six areas of organized markets administered by independent system operators in the US Eastern Interconnection and Texas. This report finds: (1) Combined, fossil and nuclear energy plants provided 89% of electricity during peak demand across all the ISOs; (2) Coal provided the most resilient form of generation in PJM; (3) The value of fuel-based power generation resilience in PJM during this event was estimated at $3.5 billion; (4) Natural gas price spikes, increased demand, and pipeline constraints led to significant fuel oil burn in the US Northeast; (5) Renewables imposed a resilience penalty on the system as output decreased as demand increased; (6) Underestimation of coal and nuclear retirements could give rise to reliability concerns and an inability to meet projected electricity demand.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

AOI2 - Initial Engineering, Testing, and Design of a Commercial-Scale Postcombustion CO 2 Capture System on an Existing Coal-Fired Generating Unit (Project Carbon)

The continued long-term use of North Dakota lignite is likely dependent on creating a business case for carbon capture, utilization, and storage (CCUS) that also addresses society’s desire to reduce carbon emissions. CCUS coupled with enhanced oil recovery appears to be the most feasible option for utilities to sustain and grow the lignite industry. Establishing a market where lignite-powered utilities provide carbon dioxide (CO 2 ) to oil producers depends upon having a cost-effective method to capture CO 2 . The application of CO 2 capture technology to lignite-fired flue gas has challenges in addition to the cost of capture, including the effects of the buildup of heat-stable salts, aerosol formation, degradation of solvents or solid sorbents, or subsequent solvent loss. Lignite, especially North Dakota lignite, presents its own set of challenges that include the combination of high sodium, sulfur, and ash contents; NO x reduction; and footprint limitations. Project Carbon was designed to address these technical barriers and provide pre-FEED (preliminary front-end engineering and design) information necessary for additional commercial demonstrations to move forward. A long-term pilot-scale evaluation of Mitsubishi Heavy Industries’ (MHI’s) KS-1™ solvent at Minnkota Power Cooperative’s lignite-fired Milton R. Young Station Unit 2 (MRY2) was a major objective of the project. The purpose of the test was to demonstrate the technology’s compatibility with MRY2’s flue gas over an extended period of time. During the long-term test, aerosol sampling and measurement were performed, and a pilot-scale baghouse was tested to determine the effect of bag material and operation on aerosol concentrations in the flue gas. Project engineering and design work were performed to support the other major project objective: a pre-FEED study of CO 2 capture at MRY2. Finally, a techno-economic assessment (TEA) of the application of CO 2 capture to MRY2 was performed. This project was performed over a period of 28 months, with a total budget of $12,700,000. The U.S. Department of Energy’s (DOE’s) National Energy Technology Laboratory, through the Energy & Environmental Research Center’s (EERC’s) Cooperative Agreement, the North Dakota Industrial Commission, and industry partners ALLETE and Minnkota Power Cooperative, funded the project. The pilot-scale test system at MRY2 performed very well for the continuous test period of 83 days. The CO 2 capture plant achieved stable operation while utilizing MHI’s KS-1™ solvent and the MHI amine emission reduction unit. No major concerns were encountered when capturing CO 2 from lignite-fired flue gas. Challenges were encountered because the cooling water temperature was warmer than needed for the capture system to operate efficiently. This affected the ability of the solvent to capture CO 2 and promoted solvent loss through solvent entrainment caused by high CO 2 gas temperature within a cyclone separator. The KS-1™ solvent and the lignite-derived flue gas were analyzed during the long-term test. Analysis of the solvent indicates that, although some metals and heat-stable salts increased over the course of the long-term test, they were at levels that can be treated with filtration and reclaiming and do not pose a concern for effective solvent operation. Fourier transform infrared (FTIR) spectrometry was successfully used to determine the composition of the lignite-derived flue gas as well as concentrations of select components of the flue gas at various locations within the EERC’s CO 2 capture system. The formation of aerosols during the capture process is of interest, as are approaches for their reduction, especially in a baghouse. Testing of aerosol removal was performed using the EERC’s portable baghouse. It was found that both Ryton and polytetrafluoroethylene (PTFE) membrane bags were effective at reducing the level of aerosols during steady-state operation. During backpulse events, however, the amount of aerosols passing through the bags was an order of magnitude lower for the Ryton bags than the PTFE membrane bags. The testing showed that proper design of the baghouse air-to-cloth ratio as well as minimization of backpulsing can dramatically reduce the amount of aerosols that pass through the bags and remain in the flue gas stream exiting a baghouse system. A technology maturation plan (TMP) was performed to enable successful development of the Kansai Mitsubishi Carbon Dioxide Recovery® (KM CDR®) Process for application to a combustion flue gas for which the process has not yet been demonstrated. In the TMP, new challenges to the MHI CO 2 capture technology during its application to MRY2 were identified. These challenges included capture from lignite-fired (as opposed to subbituminous coal-fired) flue gas, a larger scope than previous applications of the technology, and implementation in a colder climate that could affect process and equipment operability. Because MRY2 is located where stack icing in the winter could be problematic, a rime icing study was performed. Rime icing modeling indicated that, under both 100% and 50% operating loads, there is a potential for many icing events during any given part of the year in which below-freezing weather conditions exist. The models showed that a critical amount of rime ice could be formed at the stack top during two or more events per year. CO 2 capture plant stack height and location will need to be determined in order to minimize the formation of rime ice. It was found that the integration of the MHI CO 2 capture process into the normal operation of the MRY2 steam turbine is a viable alternative to a cogeneration facility to provide steam and power for the carbon capture facility. The research performed under this project showed that CO 2 capture at a lignite-fired power plant can successfully be performed. No known fatal flaws that would prevent the continued development of the MRY2 CO 2 capture facility were identified during the pre-FEED study. A TEA performed following DOE methodology shows that applying capture technology to MRY2 may not only meet but exceed the DOE-recognized state-of-the-art baseline.

20 FOSSIL-FUELED POWER PLANTS↗

Potential Impacts of Accelerated Climate Change (Second Annual Report of Work)

This study is part of the U.S. Nuclear Regulatory Commission’s (NRC) Probabilistic Flood Hazard Assessment (PFHA) research plan that aims to develop regulatory tools and guidance to support and enhance the NRC’s capacity to perform thorough and efficient reviews of license applications and license amendment requests. In Year 1, Pacific Northwest National Laboratory staff prepared an annual report that summarized recent scientific findings on climate change, with a particular focus on climatic elements that are relevant to NRC concerns on a regional level (i.e., increasing air and water temperatures, decreasing water availability, increasing frequency and intensity of storms and flooding, and sea-level rise). This report summarizes Year 2 activities, which focused on reviewing scientific findings regarding region-specific climatic extremes for the southeastern United States. According to the U.S. Global Change Research Program Third National Climate Assessment, the U.S. Southeast Region consists of 11 southeastern states, Puerto Rico, and the Virgin Islands. Except for Kentucky, Puerto Rico, and the Virgin Islands, all included states have operating nuclear power plants. Further, new nuclear power reactor permit and license applications have been submitted to the NRC in the recent past for sites located in several southeastern states. Therefore, having an improved understanding of potential climate changes and their hydrologic impacts in the Southeast Region is important to inform the PFHA research plan. Climatic features relevant to the NRC for the Southeast Region include high temperature extremes, precipitation extremes, flooding, high winds associated with tropical cyclones and tornadoes, sea-level rise, and storm surge and associated inland inundation. Drawing primarily from the climate assessment reports and peer-reviewed literature, this Year 2 annual report summarizes the observed climate, its past changes, and its projected changes, as well as 21st century hydrologic impacts in the Southeast Region. Despite the relatively mild changes observed in the past and projected in the future for the mean climate of the Southeast Region, many aspects of climatic extremes such as extreme precipitation have exhibited changes in the last century. In addition, climate and hydrologic models project further changes in the future. Pacific Northwest National Laboratory staff presented updates summarizing these findings at the Second Annual PFHA Research Workshop, which took place from January 23 to 25, 2017, at NRC Headquarters in Rockville, Maryland.

54 ENVIRONMENTAL SCIENCES↗

Global Teleconnections: Atmospheric Interactions Across Scales [Slides]

This project aims at an improved understanding of non-hydrostatic dynamics in atmospheric modeling using the DOE’s next generation climate model. One aspect that we have been focusing on is baroclinic instability which is closely related to mid-latitude cyclone genesis. The other aspect that we recently developed is E3SM simulations under Radiative-Convective Equilibrium (RCE), a prototype of tropical climate.

54 ENVIRONMENTAL SCIENCES↗

Automation is all you need: Faster Earth system models with AI/ML

Focal Area: Data acquisition and assimilation enabled by machine learning (ML), artificial intelligence (AI) and advanced methods. Science Challenge: Tropical cyclones can in- duce extreme water cycle events through dramatic precipitation and storm surge. More reliable models of intensity will translate into better prediction of the impact of extreme events in large scale Earth systems simulations. We demonstrate and describe AI/ML methodologies for rapid assimilation of new, in situ data products.

54 ENVIRONMENTAL SCIENCES↗

Science-integrated Artificial-intelligence for Flooding and precipitation Extremes (SAFE)

A grand challenge in hydrologic science is to understand why signals of climate change and variability, which are often visible in precipitation extremes at aggregate scales, are not consistently observed in the case of extreme flooding. However, a solution to this challenge may prove elusive unless the water cycle is viewed in an integrative manner. Thus, for riverine flooding, while Hortonian (infiltration excess) runoff may have stronger correlation with precipitation extremes and hence perhaps to warming trends or climate oscillators, Dunne (saturation excess) runoff may have a more complex relationships with time series of precipitation and with evaporation and transpiration, but rain-on-snow and snowmelt events may depend on land-surface and atmospheric temperatures. Atmospheric rivers and tropical cyclones lead to precipitation or flooding and are impacted by climate. Flooding assessments need to consider long-term baselines, evolving risk factors, coupled natural-human systems, and novel adaptation such as nature-inspired design.

54 ENVIRONMENTAL SCIENCES↗

Transforming ESM Physical Parameterization Development Using Machine Learning Trained on Global Cloud-Resolving Models and Process Observations

ESMs robustly predict that 21st century greenhouse warming will slowly increase global mean precipitation, rapidly increase extreme precipitation, and increase subtropical drought. ESMs agree less about precipitation trends and extremes over particular land regions critical to human societies, e. g. in semi-arid regions such as California or the Sahel, or in wetter climates prone to monsoonal rainfall (e. g. southeast Asia) or to tropical cyclones and flooding from mesoscale convective systems (e. g. the southeastern U.S.) Deep convective parameterizations and poor representation of orography and complex vegetated land surfaces contribute to this inter-model spread; clouds, aerosols and sea-surface temperature biases are also key. Reducing regional precipitation projection uncertainty has enormous planning value for water supplies, land use, wildfire, hydropower, flood control, etc. IPCC-class ESMs are making painfully slow progress on this.

54 ENVIRONMENTAL SCIENCES↗

High concentrations of ice: Investigations using polarimetric radar observations combined with in situ measurements and cloud modeling (Final Report)

This DOE-funded joint project had the over-arching goal of understanding the reasons for observed size distributions of ice particles in cold clouds. Its approach involves the use of cloud models and field observations by radar and aircraft of real storms. The project addresses three major research objectives: (1) Utilize a novel polarimetric radar technique to retrieve size distributions and amounts of ice from radar data collected during the previous DOE ARM field campaigns; (2) Evaluate the results of ice microphysical retrievals using available in situ aircraft measurements and other remote sensors (e.g., vertically pointing cloud radars and wind profilers); (3) Improve the treatment of microphysical processes leading to cloud glaciation and ice multiplication in numerical cloud models. The study was performed by three research organizations: University of Oklahoma, The Hebrew University of Jerusalem, Israel, and Lund University, Sweden. The Israel and Swedish partners were funded by the sub-awards from the University of Oklahoma. Cloud modeling studies have been performed by the research teams at The Hebrew University of Jerusalem (HUJ) and Lund University to identify the origins of high concentrations of cloud ice in areas of high ice water content (HIWC). The Hebrew University Cloud Model (HUCM) with full spectral bin microphysics and the Lund University aerosol-cloud (AC) model with a hybrid bin / bulk microphysics scheme complementing HUCM were utilized for simulations. Both research teams had particular focus on secondary ice production (SIP) as one of the possible sources of enhanced ice concentration. The HUJ group suggested a novel concept of ice multiplication during droplet freezing. It is assumed that splintering and droplet fragmentation during droplet freezing takes place because of dendritic growth within a supercooled drop. The resulting simulations of SIP generated small ice in concentrations exceeding hundreds per liter similar to what was observed in the HIWC regions of the tropical storms. The Lund team explored the SIP mechanisms such as breakup of ice particles due to ice-ice collisions and ice sublimation that are expected to dominate the continental storms. They also quantified the impact of homogeneous nucleation of cloud droplets on the total number concentration of ice at very low temperatures near the tops of the clouds. Additionally, the Lund AC model is able to simulate the effect of aerosols of various types (including biological) on the cloud life cycle and the corresponding ice production. The HUCM / AC model was used to simulate one of the “golden” cases of the DOE MC3E campaign on 20 May 2011. The model output was converted into the fields of polarimetric radar variables using the polarimetric radar forward operator developed at the University of Oklahoma and compared with radar observations and in situ microphysical measurements onboard research aircraft. It was demonstrated that specific differential phase KDP is the best radar parameter to identify the HIWC areas and quantify the corresponding ice parameters. For the first time, the shape of the vertical profile of KDP was realistically reproduced by the cloud model with the KDP maximum in the dendritic growth layer (DGL) centered at the -15°C isotherm. The University of Oklahoma team has developed a methodology for polarimetric radar retrievals of such microphysical parameters of ice as ice water content (IWC), mean volume diameter (Dm), and total number concentration (Nt) of ice particles. These retrievals have been validated using in situ aircraft measurements during 6 field campaigns and proved to be quite robust and reliable. This allowed to build the first climatology of the vertical profiles of polarimetric radar variables and retrieved microphysical parameters for the three types of weather systems: continental MCSs, maritime MCSs, and tropical cyclones / hurricanes (Hu and Ryzhkov 2022). The data were collected by a multitude of the WSR-88D radars in 13 continental and 10 maritime MCSs and 11 landfalling hurricanes. The HIWC areas were identified within the examined storms and the corresponding “HIWC statistics” was compared with the “background” one without HIWC. An overarching conclusion of the study is that maritime tropical storms (MCSs and hurricanes) are characterized by smaller size ice in higher concentration compared to the continental MCSs. High ice water content in the HIWC areas is primarily caused by a strong jump in a number concentration of ice particles rather than the increase of their size compared to the “background” environment. This may point to the homogeneous nucleation of excessive amounts of supercooled droplets and / or secondary ice production as the possible origins of HIWC. Such a climatology provides a good observational reference for the modelers to evaluate the performance of their models. As an example, the in-depth analysis of the 20 May 2011 MC3E case shows that the advanced cloud models developed in the course of this study still tend to underestimate the number concentration of ice in the HIWC areas although they succeed in reproducing realistically looking vertical profiles of IWC and Nt. The results of the project research are summarized in 13 journal papers.

54 ENVIRONMENTAL SCIENCES↗

Puerto Rico Historical Climate Analysis: A closer look at complex tropical terrain

Small tropical islands like Puerto Rico are especially vulnerable to climate change impacts, yet are often underrepresented in most datasets because the spatial resolution is too coarse to sufficiently cover their complex terrain. This study was done to better understand how the climate has changed in the various regions of Puerto Rico, which will support a transition to renewable energy and aid in projecting future climate impacts on the residents and land they live on. This study used multiple datasets including Daymet, a daily surface weather and climatological summary; European Centre for Medium-Range Weather Forecasts Reanalysis version 5 (ERA5); and station observations. The climate variables examined here include minimum and maximum near-surface air temperature, daily precipitation, incident shortwave radiation, and large-scale upper atmosphere conditions. The time periods cover the years 1950–2019. Results in both Daymet and station observations show long-term warming trends throughout every season. In particular, the minimum winter temperatures increased the most compared with maximum and mean air temperature. Northeast Puerto Rico, where the majority of the island’s population is located, experienced the largest warming. Summertime precipitation has decreased over time, and spring and fall precipitation has increased. The largest increase in fall is because there has been more available precipitable water, lower sea-level pressure, and favorable cyclonic circulations from the trade winds over the past seven decades. Overall, wet days are getting wetter, while dry days are getting drier. While there are good solar energy potential, we see a long-term decreasing trend in shortwave radiation over time in all seasons across entire island, possibly due to the increase of cloud cover.

54 ENVIRONMENTAL SCIENCES↗

TRACER-Uncrewed Aircraft System (TRACER-UAS) Field Campaign Report

Convective processes drive the development of clouds across a variety of scales, thereby playing a central role in governing weather and climate globally. These processes help to set the stage for circulations that redistribute heat and moisture throughout the lower atmosphere, and simultaneously develop storms that supply precipitation to regions that depend on such rain events for supporting a variety of societal needs. At the same time, extreme precipitation events can result in localized flooding of low-lying areas, posing hazards to transportation and regional inhabitants, and potentially damaging structures and infrastructure. As a result, there is an inherent need to better understand the drivers and modulators of clouds and precipitation and leverage such understanding to make projections of how these important systems may evolve with a changing climate. With nearly three billion of Earth’s human inhabitants living within 200 km of a shoreline, development of such understanding is particularly important in coastal regimes. Central drivers of convective cloud development and life cycle in coastal environments include synoptic forcing, local meso- and microscale circulation regimes, microphysical evolution, and aerosol properties. Atmospheric boundary layer (ABL) development and its evolution can help drive the formation and organization of convective clouds, which then impart their own controls through dynamic processes related to latent heating and cooling (including cold-pool formation and propagation), three-dimensional radiative effects, and background environmental conditions (Fan et al. 2016). Such clouds have been contributing to record precipitation events in southeast Texas in recent years, relative to the last several decades of data from regional precipitation gauges (Fagnant et al. 2020). The greater Houston urban area has experienced particularly large increases in the frequency of extreme rainfall events, with enhanced intensity of extreme events (stretching of distribution tails) having potentially significant implications for watershed floodplain planning and mapping in greater Houston and Harris County. While the most extreme precipitation events were associated with tropical cyclones (e.g., Tropical Storm Allison and Hurricane Harvey; Blood 2014, Kao et al. 2019), strong thunderstorms can also deliver large amounts of precipitation over the area over relatively short periods.

54 ENVIRONMENTAL SCIENCES↗