Search NASA⌕ Search

SEARCH · Search NASA

Results for “FAILURE MODES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69

Impact Testing of Aluminum 2024 and Titanium 6Al-4V for Material Model Development

One of the difficulties with developing and verifying accurate impact models is that parameters such as high strain rate material properties, failure modes, static properties, and impact test measurements are often obtained from a variety of different sources using different materials, with little control over consistency among the different sources. In addition there is often a lack of quantitative measurements in impact tests to which the models can be compared. To alleviate some of these problems, a project is underway to develop a consistent set of material property, impact test data and failure analysis for a variety of aircraft materials that can be used to develop improved impact failure and deformation models. This project is jointly funded by the NASA Glenn Research Center and the FAA William J. Hughes Technical Center. Unique features of this set of data are that all material property data and impact test data are obtained using identical material, the test methods and procedures are extensively documented and all of the raw data is available. Four parallel efforts are currently underway: Measurement of material deformation and failure response over a wide range of strain rates and temperatures and failure analysis of material property specimens and impact test articles conducted by The Ohio State University; development of improved numerical modeling techniques for deformation and failure conducted by The George Washington University; impact testing of flat panels and substructures conducted by NASA Glenn Research Center. This report describes impact testing which has been done on aluminum (Al) 2024 and titanium (Ti) 6Al-4vanadium (V) sheet and plate samples of different thicknesses and with different types of projectiles, one a regular cylinder and one with a more complex geometry incorporating features representative of a jet engine fan blade. Data from this testing will be used in validating material models developed under this program. The material tests and the material models developed in this program will be published in separate reports.

Pereira, J. Michael↗

Impact Testing of Inconel 718 for Material Impact Model Development

One of the difficulties with developing and verifying accurate impact models is that parameters such as high strain-rate material properties, failure modes, static properties, and impact test measurements are often obtained from a variety of different sources using different materials, with little control over consistency among the different sources. In addition, there is often a lack of quantitative measurements in impact tests to which the models can be compared. To alleviate some of these problems, a project is underway to develop a consistent set of material property, impact test data, and failure analysis for a variety of aircraft materials that can be used to develop improved impact failure and deformation models. This project is jointly funded by the NASA Glenn Research Center and the Federal Aviation Administration (FAA) William J. Hughes Technical Center. Unique features of this set of data are that all material property and impact test data are obtained using traceable material, the test methods and procedures are extensively documented, and all of the raw data is available. Four parallel efforts are currently underway. The Ohio State University conducts both measurement of material deformation and failure response over a wide range of strain rates and temperatures and failure analysis of material property specimens and impact test articles. The George Mason University conducts the development of improved numerical modeling techniques for deformation and failure. Glenn conducts the impact testing of flat panels and substructures. This report describes impact testing performed on Inconel 718 sheet and plate samples of different thicknesses with different types of projectiles, one a regular cylinder and one with a more complex geometry incorporating features representative of a jet engine fan blade. Data from this testing will be used in validating material models developed under this program. The material tests and the material models developed in this program will be published in separate reports.

J Michael Pereira↗

Fracture mechanics approach to TRISO fuel particle failure analysis

Weibull stress-based methods for failure probability assessment have been developed and analyzed to assess the integrity of tristructural isotropic (TRISO) fuel particles during fuel life cycles and accident operating conditions. While simple, these methods entail a number of drawbacks when stress concentrates near crack tips, including finite element mesh size dependency when the Weibull stress is averaged over the finite element domain. Fracture mechanics approaches involving the use of interaction integrals eliminate this lack of mesh convergence and produce consistent fracture predictions. In this work, we use an interaction integral approach to computing stress intensity factors for a crack in the inner pyrolytic carbon layer perpendicular to the silicon carbide layer, which is simplified representation of a failure mode in TRISO particles. Further, the interface between these two TRISO layers has been shown to become porous, which we simulate by considering a transition of mechanical properties over such porous length, i.e. the layers are modeled as a functionally graded material. Aspects such as porosity and thermal and irradiation eigenstrains are considered in computing the stress intensity factor from a fracture mechanics approach and compared with the known Weibull stress failure approach. The methodology introduced in this paper enables a more general fracture probability assessment in TRISO particles and eliminates the need to identify best suited parameters when using local or averaged stress-based failure criterion. Finally, the numerical sensitivity studies show how parameters such as the porous transition zone length, the material stiffness, and creep affect the probability of TRISO fuel particle failure.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Dynamic-tensile-extrusion response of fluoropolymers

The current work applies the recently developed Dynamic-Tensile-Extrusion (Dyn-Ten-Ext) technique to polytetrafluoroethylene (PTFE) and polychlorotrifluoroethylene (PCTFE). Similar to the Taylor Impact Rod, Dynamic-Tensile-Extrusion is a strongly integrated test, probing a wide range of strain rates and stress states. However, the stress state is primarily tensile enabling investigation of dynamic tensile failure modes. Here we investigate the influence of this propensity to neck or not between PCTFE and PTFE on their response under dynamic tensile extrusion loading. The results of the Dyn-Ten-Ext technique are compared with two classic techniques. Both polymers have been investigated using Tensile Split Hopkinson Pressure Bar. The quasistatic and dynamic responses of both fluoro-polymers have been extensively characterized. The two polymers exhibit significantly different failure behavior under tensile loading at moderate strain rates. Polytetrafluoroethylene resists formation of a neck and exhibits significant strain hardening. Independent of temperature or strain rate, PTFE sustains true strains to failure of approximately 1.5. Polychlorotrifluoroethylene, on the other hand, consistently necks at true strains of approximately 0.05.

36 MATERIALS SCIENCE↗

Electrochemical-Mechanical Coupling Strongly Affects the Performance of Nanopore, Thin-Film, and Solid-State Batteries

Here, the present study focuses on the electrochemical-mechanical (ECM) coupling effects of a thin-film, solid-state battery with only stiff, ceramic materials, in contrast to prior investigations that focus on individual active material particles or aggregations of particles. We model the impacts of ECM couplings including stress-transport and stress-equilibrium potential on the full-cell performance and potential mechanical failure modes of a thin-film battery conformally deposited in a nanopore scaffold, which is an experimentally achievable device. Model results indicate electrode volume changes due to lithium insertion or removal, along with mechanical boundary conditions, result in stress gradients that alter the lithium-ion flux, reduce lithium concentration gradients, and improve cell rate capability. However, the high stress levels in the cell can also lead to mechanics-related failure such as the separation of cell layers. For the parameter set in this work, stress-transport coupling has a much greater influence on rate capability than stress-potential coupling. Optimization of thin-film batteries to harness the benefits of ECM coupling effects requires leveraging geometric design and material selection. The current work underscores the need for further theoretical and experimental investigation into ECM coupling effects in thin-film batteries to enhance their understanding and design optimization.

25 ENERGY STORAGE↗

NASA-LaRc Flight-Critical Digital Systems Technology Workshop

The outcome is documented of a Flight-Critical Digital Systems Technology Workshop held at NASA-Langley December 13 to 15 1988. The purpose of the workshop was to elicit the aerospace industry's view of the issues which must be addressed for the practical realization of flight-critical digital systems. The workshop was divided into three parts: an overview session; three half-day meetings of seven working groups addressing aeronautical and space requirements, system design for validation, failure modes, system modeling, reliable software, and flight test; and a half-day summary of the research issues presented by the working group chairmen. Issues that generated the most consensus across the workshop were: (1) the lack of effective design and validation methods with support tools to enable engineering of highly-integrated, flight-critical digital systems, and (2) the lack of high quality laboratory and field data on system failures especially due to electromagnetic environment (EME).

Meissner, C. W., Jr.↗

Reliability-Based Design Optimization of a Composite Airframe Component

A stochastic design optimization methodology (SDO) has been developed to design components of an airframe structure that can be made of metallic and composite materials. The design is obtained as a function of the risk level, or reliability, p. The design method treats uncertainties in load, strength, and material properties as distribution functions, which are defined with mean values and standard deviations. A design constraint or a failure mode is specified as a function of reliability p. Solution to stochastic optimization yields the weight of a structure as a function of reliability p. Optimum weight versus reliability p traced out an inverted-S-shaped graph. The center of the inverted-S graph corresponded to 50 percent (p = 0.5) probability of success. A heavy design with weight approaching infinity could be produced for a near-zero rate of failure that corresponds to unity for reliability p (or p = 1). Weight can be reduced to a small value for the most failure-prone design with a reliability that approaches zero (p = 0). Reliability can be changed for different components of an airframe structure. For example, the landing gear can be designed for a very high reliability, whereas it can be reduced to a small extent for a raked wingtip. The SDO capability is obtained by combining three codes: (1) The MSC/Nastran code was the deterministic analysis tool, (2) The fast probabilistic integrator, or the FPI module of the NESSUS software, was the probabilistic calculator, and (3) NASA Glenn Research Center s optimization testbed CometBoards became the optimizer. The SDO capability requires a finite element structural model, a material model, a load model, and a design model. The stochastic optimization concept is illustrated considering an academic example and a real-life raked wingtip structure of the Boeing 767-400 extended range airliner made of metallic and composite materials.

Patnaik, Surya N.↗

Architecture-Level Dependability Analysis of a Medical Decision Support System

Recent advances in techniques such as image analysis, text analysis and machine learning have shown great potential to assist physicians in detecting and diagnosing health issues in patients. In this paper, we describe the approach and findings of an architecture-level dependability analysis for a mammography decision support system that incorporates these techniques. The goal of the research described in this paper is to provide an initial understanding of the dependability issues, particularly the potential failure modes and severity, in order to identify areas of potential high risk. The results will guide design decisions and provide the basis of a dependability and performance evaluation program.

99 GENERAL AND MISCELLANEOUS↗

Model Based Engineering for Software Assurance

NASA's successful development of next generation space vehicles, habitats, and robotic systems will require reliable hardware and software systems. The aim of this initiative is to develop modeling methodology and tools to support Model-Based Systems Engineering (MBSE) for software assurance and reliability analysis. This effort expands the Unified Modeling Language (UML) software design models to include fault data for the extraction of Failure Modes and Effects Criticality Analysis (FMECA) and Fault Tree Analysis (FTA) for software. We explored different modeling approaches to integrate the UML software design models with the Systems Modeling Language (SysML) system models to generate an integrated model and reliability tools that take into account software and hardware interfaces.The benefits of this concept directly affect the safety community with quick turnarounds to produce software assurance and reliability analysis artifacts and the ability to visualize failure effects, both hardware and software. The result is enhanced system design integrity and early identification of system risks. This initiative will enable software assurance activities early in the system design lifecycle, facilitating the discovery of design weaknesses and enhancing the capability to produce safe, hazard-free systems

Wang, Lui↗

Computational micromechanics of fatigue of microstructures in the HCF–VHCF regimes

Advances in higher resolution experimental techniques have shown that metallic materials can develop fatigue cracks under cyclic loading levels significantly below the yield stress. Indeed, the traditional notion of a fatigue limit can be recast in terms of limits associated with nucleation and arrest of fatigue cracks at the microstructural scale. Though fatigue damage characteristically emerges from irreversible dislocation processes at sub-grain scales, the specific microstructure attributes, environment, and loading conditions can strongly affect the apparent failure mode and surface to subsurface transitions. This paper discusses multiple mechanisms that occur during fatigue loading in the high cycle fatigue (HCF) to very high cycle fatigue (VHCF) regimes. We compare these regimes, focusing on strategies to bridge experimental and modeling approaches exercised at multiple length scales and discussing particular challenges to modeling and simulation regarding microstructure-sensitive fatigue driving forces and thresholds. Finally, we discuss some of the challenges in predicting the transition of failure mechanisms at different stress and strain amplitudes.

36 MATERIALS SCIENCE↗

Grain Boundary Diffusion Characterized by KPFM

Materials aging is a high-consequence failure mode in electronic systems. Such mechanisms can degrade the electrical properties of connectors, relays, wire bonds, and other interconnections. Lost performance will impact, not only that of the device, but also the function and reliability of next-level assemblies and the weapons system as a whole. The detections of changes to materials surfaces at the nanometer-scale resolution, provides a means to identify aging processes at their early stages before they manifest into latent failures that affect system-level performance and reliability. Diffusion will be studied on thin films that undergo accelerated aging using the nanometer scale characterization technique of Frequency Modulated Kelvin Probe Force Microscopy (FM-KPFM). The KPFM provides a relatively easy, non-destructive methodology that does not require high-vacuum facilities to obtain nanometer spatial resolution of surface chemistry changes. The KPFM method can provide the means to measure surface, and near-surface, elemental concentrations that allow the determination of diffusion rate kinetics. These attributes will be illustrated by assessing diffusion in a thin film couple. Validation data will obtained from traditional techniques: (a) Auger electron spectroscopy (AES), x-ray fluorescence (XRF), and xray photoelectron spectroscopy (XPS).

36 MATERIALS SCIENCE↗

Response Bias of Electrical Cable Coatings at FIRE Conditions (REBECCA-FIRE)

This report presents the results of a series of cable fire-retardant coating tests sponsored by the US Nuclear Regulatory Commission (NRC) Office of Nuclear Regulatory Research and performed at Sandia National Laboratories in conjunction with the National Institute of Standards and Technology (NIST). The goal of the tests was to assess the effects of three commercially available fire-retardant cable coating materials on cable thermal and electrical response behavior under fire-exposure conditions. The specific test objectives were to assess, under severe radiant heating conditions, how the coating materials impacted (1) cable thermal response and (2) electrical integrity behavior. The tests were not explicitly designed to assess the impact of the coatings on cable flammability, although some insights relative to the burning behavior of the coating materials themselves and cable ignition times were gained. NIST is currently investigating these attributes under the Cable Heat Release, Ignition, and Spread in Tray Installations During Fire (CHRISTIEFIRE) program (NUREG/CR-7010). The cables used in construction of the test articles were all seven-conductor 12AWG (American wire gage) control or power type copper conductor electrical cables. Two cable insulation types were represented, a polyethylene thermoplastic material and a cross-linked polyethylene thermoset material. Both cable types used have been tested extensively in recent NRC-sponsored experimental programs involving both circuit failure modes and effects testing and fire growth testing. The test articles included uncoated cables and cables coated with one of three fire-retardant coating materials: Carboline Intumastic 285, Flamemastic F-77, and Vimasco 3i. Test configurations included single lengths of cables, bundles of seven cables, and bundles of ten cables. The tests show that, under certain conditions, the fire-retardant coatings provide a substantial benefit relative to delays in cable heating, ignition and electrical failure times. However, as has been seen in prior test programs, the performance varied substantially among the coating products. The current tests also show that the benefit gained by the coatings was heavily dependent on the thermal mass of the coated cable system. Low thermal mass systems, such as the single lengths of coated cable, saw essentially no net benefit from application of the coatings. Intermediate mass systems, represented by the seven-cable bundles, saw some benefit from application of the coatings, but the benefit was inconsistent, and some cables in the bundles saw essentially no delay in thermal response or time to failure. For the larger thermal mass systems, represented by the ten-cable bundles, the benefit of the coatings was both more pronounced and more consistent with all coatings providing a measurable benefit.

36 MATERIALS SCIENCE↗

Grain Boundary Diffusion Characterized by KPFM

Materials aging is a high-consequence failure mode in electronic systems. Such mechanisms can degrade the electrical properties of connectors, relays, wire bonds, and other interconnections. Lost performance will impact, not only that of the device, but also the function and reliability of next-level assemblies and the weapons system as a whole. The detections of changes to materials surfaces at the nanometer-scale resolution, provides a means to identify aging processes at their early stages before they manifest into latent failures that affect system-level performance and reliability. Diffusion will be studied on thin films that undergo accelerated aging using the nanometer scale characterization technique of Frequency Modulated Kelvin Probe Force Microscopy (FM-KPFM). The KPFM provides a relatively easy, non-destructive methodology that does not require high-vacuum facilities to obtain nanometer spatial resolution of surface chemistry changes. The KPFM method can provide the means to measure surface, and near-surface, elemental concentrations that allow the determination of diffusion rate kinetics. These attributes will be illustrated by assessing diffusion in a thin film couple. Validation data will obtained from traditional techniques: (a) Auger electron spectroscopy (AES), x-ray fluorescence (XRF), and xray photoelectron spectroscopy (XPS).

36 MATERIALS SCIENCE↗

Highly Loaded Composite Strut Test Results

Highly loaded composite struts from a proposed truss-based Altair lunar lander descent stage concept were selected for development under NASA's Advanced Composites Technology program. Predicted compressive member forces during launch and ascent of over -100,000 lbs were much greater than the tensile loads. Therefore, compressive failure modes, including structural stability, were primary design considerations. NASA's industry partner designed and built highly loaded struts that were delivered to NASA for testing. Their design, fabricated on a washout mandrel, had a uniform-diameter composite tube with composite tapered ends. Each tapered end contained a titanium end fitting with facing conical ramps that are overlaid and overwrapped with composite materials. The highly loaded struts were loaded in both tension and compression, with ultimate failure produced in compression. Results for the two struts tested are presented and discussed, along with measured deflections, strains and observed failure mechanisms.

Wu, K. C.↗

Space Charge Analysis Capabilities for the Evaluation of High Voltage Insulation Materials

Materials development is crucial for the advancement of electric aviation. Current research focusing on novel multifunctional materials is underway to solve the needs for aerospace systems; however, additional testing of these materials to understand their failure modes is equally critical. This project will utilize pulsed electroacoustic (PEA) instrumentation to investigate space charge accumulation of multifunctional composites and other insulation materials critical to robust high power transmission systems. Evaluating the space charge phenomena in dielectric materials will provide unique and fundamentally necessary data to determine the feasibility and lifetime of any high voltage insulation system. When electrical charge is injected into a solid dielectric, charge can accumulate and become trapped, leading to the failure of the insulation via breakdown or arcing events. This study will discuss the pulsed electroacoustic methodology and its use on evaluating various dielectric polymer and composite films.

pulsed electroacoustic↗

Numerical Modelling of Glass Fibre Reinforced Laminates Subjected to a Low Velocity Impact

This paper presents a series of numerical predictions of the perforation behaviour of glass fibre laminates subjected to quasi-static and low-velocity impact loading. Both shear and tensile failure criteria were used in the finite element models to simulate the post-failure processes via an automatic element removal procedure. The appropriate material properties, obtained through a series of uniaxial tension and bending tests on the composites, were used in the numerical models. Four, eight and sixteen ply glass fibre laminates panels were perforated at quasi-static rates and under low-velocity impact loading. Reasonably good correlation was obtained between the numerical simulations and the experimental results, both in terms of the failure modes and the load-deflection relationships before and during the penetration phase. The predicted impact energies of the GFRP panels were compared with the experimental data and reasonable agreement was observed.

36 MATERIALS SCIENCE↗

RAMI Analyses of Heating Neutral Beam and Diagnostic Neutral Beam Systems for ITER

A RAMI (Reliability, Availability, Maintainability, Inspectability) analysis has been performed for the heating (and current drive) neutral beam (HNB) and diagnostic neutral beam (DNB) systems of the ITER device. The objective of these analyses is to implement RAMI engineering requirements for design and testing to prepare a reliability-centred plan for commissioning, operation, and maintenance of the system in the framework of technical risk control to support the overall ITER Project. These RAMI requirements will correspond to the RAMI targets for the ITER project and the compensating provisions to reach them as deduced from the necessary actions to decrease the risk level of the function failure modes. The RAMI analyses results have to match with the procurement plan of the systems.

43 PARTICLE ACCELERATORS↗

Efficient Simulation and Abuse Modeling of Mechanical-Electrochemical-Thermal Phenomena in Li-Ion Batteries

This poster covered simultaneous coupling of electrochemical-thermal models with mechanical deformation in lithium ion batteries. Efficiency and stability of mechanical models was significantly enhanced by implementing electrochemical models into LS-DYNA using User-Defined Elements. Six case studies were built and licensed out to participants from Industry for initial testing and their feedback is being incorporated into these tools. Dynamic response of the cells was incorporated by measuring mechanical response of components at strain rates as high as 250 /s. Temperature range for property measurements was expanded (as high as 200 degrees C) to account for property changes at high temperatures experienced by cell components under battery abuse. Multi-cell validation has been expanded to include four different sets of experimental data, with support from various partners. Complex failure modes and fracture response are currently being investigated. These are still very challenging, given the limited amount of prior work available in the literature.

25 ENERGY STORAGE↗