Search NASA⌕ Search

SEARCH · Search NASA

Results for “Structural components”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69

Superplastic forming/weld-brazing of Ti-6Al-4V panels for enhanced structural efficiency

An account is given of the results obtained by NASA-sponsored studies which exploit the processing advantages of superplastic forming (SPF) and joining by weld-brazing (WB) for the fabrication of Ti-alloy skin-stiffened structural components. The buckling strengths of panels with stiffeners having the geometry of a conventional hat shape are compared with those of panels having advanced-geometry stiffereners. Both single- and multiple-stiffened panels have been evaluated at room temperature; the SPF/WB panels with advanced-geometry stiffeners developed up to 60-percent higher buckling strength than panels with conventional-geometry stiffeners. Selective stiffener reinforcement with a boron-reinforced Al-matrix MMC was also evaluated.

Royster, Dick M.↗

Constitutive modeling for isotropic materials (HOST)

The results of the first year of work on a program to validate unified constitutive models for isotropic materials utilized in high temperature regions of gas turbine engines and to demonstrate their usefulness in computing stress-strain-time-temperature histories in complex three-dimensional structural components. The unified theories combine all inelastic strain-rate components in a single term avoiding, for example, treating plasticity and creep as separate response phenomena. An extensive review of existing unified theories is given and numerical methods for integrating these stiff time-temperature-dependent constitutive equations are discussed. Two particular models, those developed by Bodner and Partom and by Walker, were selected for more detailed development and evaluation against experimental tensile, creep and cyclic strain tests on specimens of a cast nickel base alloy, B19000+Hf. Initial results comparing computed and test results for tensile and cyclic straining for temperature from ambient to 982 C and strain rates from 10(exp-7) 10(exp-3) s(exp-1) are given. Some preliminary date correlations are presented also for highly non-proportional biaxial loading which demonstrate an increase in biaxial cyclic hardening rate over uniaxial or proportional loading conditions. Initial work has begun on the implementation of both constitutive models in the MARC finite element computer code.

Lindholm, Ulric S.↗

Application of finite-element-based solution technologies for viscoplastic structural analyses

Finite-element solution technology developed for use in conjunction with advanced viscoplastic models is described. The development of such solution technology is necessary for performing stress/life analyses of engineering structural problems where the complex geometries and loadings make the conventional analytical solutions difficult. The versatility of the solution technology is demonstrated by applying it to viscoplastic models possessing different mathematical structures and encompassing isotropic and anisotropic material. The computational results qualitatively replicate deformation behavior observed in experiments on prototypical structural components.

Arya, V. K.↗

Using template/hotwire cutting to demonstrate moldless composite fabrication

The objective of this experiment is to provide a simple, inexpensive composite fabrication technique which can be easily performed with a minimum of equipment and facilities. This process eliminates expensive female molds and uses only male molds which are easily formed from foam blocks. Once the mold is shaped, it is covered with fiberglass and becomes a structural component of the product.

Coleman, J. Mario↗

Flexural fatigue life prediction of closed hat-section using materially nonlinear axial fatigue characteristics

Straight or curved hat-section members are often used as structural stiffeners in aircraft. For instance, they are employed as stiffeners for the dorsal skin as well as in the aerial refueling adjacent area structure in F-106 aircraft. The flanges of the hat-section are connected to the aircraft skin. Thus, the portion of the skin closing the hat-section interacts with the section itself when resisting the stresses due to service loads. The flexural fatigue life of such a closed section is estimated using materially nonlinear axial fatigue characteristics. It should be recognized that when a structural shape is subjected to bending, the fatigue life at the neutral axis is infinity since the normal stresses are zero at that location. Conversely, the fatigue life at the extreme fibers where the normal bending stresses are maximum can be expected to be finite. Thus, different fatigue life estimates can be visualized at various distances from the neural axis. The problem becomes compounded further when significant portions away from the neutral axis are stressed into plastic range. A theoretical analysis of the closed hat-section subjected to flexural cyclic loading is first conducted. The axial fatigue characteristics together with the related axial fatigue life formula and its inverted form given by Manson and Muralidharan are adopted for an aluminum alloy used in aircraft construction. A closed-form expression for predicting the flexural fatigue life is then derived for the closed hat-section including materially nonlinear action. A computer program is written to conduct a study of the variables such as the thicknesses of the hat-section and the skin, and the type of alloy used. The study has provided a fundamental understanding of the flexural fatigue life characteristics of a practical structural component used in aircraft when materially nonlinear action is present.

Razzaq, Zia↗

The interstellar D1 line at high resolution

Observations at a resolving power or a velocity resolution are reported of the interstellar D(sub 1) line of Na I in the spectra of gamma Cas, delta Ori, epsilon Ori, pi Sco, delta Cyg, and alpha Cyg. An echelle grating was used in a double-pass configuration with a CCD detector in the coude spectrograph of the 2.7 m reflector at McDonald Observatory. At least 42 kinematically distinct clouds are detected along the light paths to the five more distant stars, in addition to a single cloud seen toward delta Cyg. The absorption lines arising in 13 of the clouds are sufficiently narrow and unblended to reveal clearly resolved hyperfine structure components split by 1.05 km/s. An additional 13 clouds apparently show comparably narrow, but more strongly blended, lines. For each individual cloud, upper limits T(sub max) and (v sub t)(sub max) on the temperature and the turbulent velocity, respectively, are derived by fitting the observed lines with theoretical absorption profiles.

Hobbs, L. M.↗

An experimental evaluation of the tensile strength of impact ice

The evaluation of the tensile strength of impact built-up ice on structural components has been prompted by such problems as electrical transmission line losses and catastrophic failures in Arctic regions, deicing problems with fixed-wing and rotary-wing aircraft, etc. It is demonstrated that the conventional tensile-testing technique furnishes adequate data on artificially refrigerated ice, and helps establish the influence of extrinsic factors on ice tensile strength.

Xian, X.↗

Comment on predissociation of O2 in the B state

Theoretical models and experimental data on the predissociation of O2 in the B state are analyzed, with a focus on the results reported by Wodtke et al. (1988). Absorption cross sections in the (11,0) Schumann-Runge band of O2 at 79 K (Yoshino et al., 1987) are matched to curves synthesized from lower fine-structure components for 5Pi(u) and 3Pi(u) predissociative mechanisms. It is concluded that the 3Pi(u) predominance proposed by Wodtke et al. is not justified by the data. In a reply by Wodtke and Huwel, the need for further studies to clarify the apparent discrepancies between absorption and emission spectroscopy is indicated.

Freeman, D. E.↗

A search for methylene in the Orion nebula

A deep search for the J = 4-3 and 5-4 fine-structure components of the N(KK) = 4(04)-3(13) rotational transition of methylene toward the hot core of the Orion KL nebula is conducted. An approximate 4-sigma emission feature which is frequency-coincident with a hyperfine blend of the J = 4-3 component is detected, and weak features (about 2-3 sigma) frequency-coincident with the resolved F = 6-5 and 5-4 hyperfine components of the J = 5-4 component are observed. The relative intensities of these spectral features and their observational repeatability suggest that assignment to interstellar CH2 is likely correct, although the result must be confirmed.

Hollis, J. M.↗

Unsteady transonic Navier-Stokes computations for an oscillating wing using single and multiple zones

Modern jet transports and maneuvering tactical fighters operating in the transonic regime often give rise to time-dependent fluid physics that interact with flexible structural components, e.g., vortical flow, shocks, and separation. Efficient computational fluid dynamic (CFD) methods are required to study such computationally intensive problems. In this work a numerical method is presented to address this problem. Time-dependent, compressible, Navier-Stokes equations are used to simulate unsteady transonic flow about a three-dimensional rigid wing undergoing a forced periodic motion in angle of attack. An efficient, implicit, diagonal algorithm is utilized because of its low operation count per time step compared to other methods that solve systems of block matrix equations. The formal time accuracy is addressed theoretically and demonstrated numerically by comparison of computational results with experimental data. A zonal grid approach, capable of treating complex geometries, is presented and its time accuracy is demonstrated by comparing a zonal computation with a single grid computation and experimental data.

Chaderjian, Neal M.↗

Advanced Photovoltaic Solar Array program status

The Advanced Photolvoltaic Solar Array (APSA) Program is discussed. The objective of the program is to demonstrate a producible array system by the end of this decade with a beginning-of-life (BOL) specific power of 130 W/kg at 10 kW as an intermediate milestone toward the ultimate goal of 300 W/kg at 25 kW by the year 2000. The near-term goal represents a significant improvement over existing rigid panel flight arrays (25 to 45 W/kg) and the first-generation flexible blanket NASA/OAST SAFE I array of the early 1980s, which was projected to provide about 60 W/kg BOL. The prototype wing hardware is in the last stages of fabrication and integration. The current status of the program is reported. The array configuration and key design details are shown. Projections are shown for future performance enhancements that may be expected through the use of advanced structural components and solar cells.

Kurland, Richard M.↗

Characterization of structural connections using free and forced response test data

The accurate prediction of system dynamic response often has been limited by deficiencies in existing capabilities to characterize connections adequately. Connections between structural components often are complex mechanically, and difficult to accurately model analytically. Improved analytical models for connections are needed to improve system dynamic predictions. A procedure for identifying physical connection properties from free and forced response test data is developed, then verified utilizing a system having both a linear and nonlinear connection. Connection properties are computed in terms of physical parameters so that the physical characteristics of the connections can better be understood, in addition to providing improved input for the system model. The identification procedure is applicable to multi-degree of freedom systems, and does not require that the test data be measured directly at the connection locations.

Lawrence, C.↗

Performance evaluations of oxidation-resistant carbon-carbon composites in simulated hypersonic vehicle environments

An evaluation is made of the oxidation-protection requirements of carbon-carbon composite (CCC) structural components in a hypersonic vehicle aerothermodynamic environment, where maximum test temperatures in air are of the order of 2800 F, and pressures range from 0.03 to 1.0 atm. The specimens were exposed to high humidity between tests. Attention was given to the effects of coating composition and thickness, and of substrate architecture and surface preparation, on the oxidation resistance of CCCs. Both surface preparation and coating chemistry have a profound effect on coating adherence and longevity.

Barrett, D. M.↗

Analysis of elastically tailored viscoelastic damping member

For more than two decades, viscoelastic materials have been commonly used as a passive damping source in a variety of structures because of their high material loss factors. In most of the applications, viscoelastic materials are used either in series with or parallel to the structural load path. The latter is also known as the constrained-layer damping treatment. The advantage of the constrained-layer damping treatment is that it can be incorporated without loss in structural integrity, namely, stiffness and strength. However, the disadvantages are that: (1) it is not the most effective use of the viscoelastic material when compared with the series-type application, and (2) weight penalty from the stiff constraining layer requirement can be excessive. To overcome the disadvantages of the constrained-layer damping treatment, a new approach for using viscoelastic material in axial-type structural components, e.g., truss members, was studied in this investigation.

Chen, G.-S.↗

Dust clouds in Orion and the interstellar neutral hydrogen distribution

According to published examples of the far IR observations in the Orion and its surroundings, several well defined dust clouds of different sizes and structure are present. For comparison of these clouds with the neutral hydrogen distribution on the area of approx. 1000 sq degs, the data from Pulkovo Sky Survey in the interstellar neutral Hydrogen Radio Line as well as special observations with the RATAN-600 telescope in 21 cm line were used. From the materials of Pulkovo HI Survey, the data were taken near the line emission at ten velocities between -21.8 and +25.6 km/s LSR for the structural component of the interstellar hydrogen emission. The results given concern mainly the Orion's Great Dust Cloud and the Lambda Orionis region where the information about the situation with the dust and interstellar hydrogen is very essential for interpretation.

Bystrova, N. V.↗

IUE and Einstein observations of the LINER galaxy NGC 4579

Results of International Ultraviolet Explorer (IUE) and Einstein observations of the LINER galaxy NGC 4579 are reported. Spatial profiles of the long wavelength IUE emission show a two component structure, with an unresolved core superimposed on broader underlying emission. The core spectrum shows strong C II lambda 2326 and broad Mg II lambda 2800 emission, and perhaps emission due to blends of Fe II multiplets (2300 to 23600 angstrom). The short wavelength emission is spatially unresolved, and shows C II lambda 1335, C III lambda 1909 broad C IV lambda 1550 emission, and a broad feature at approximately 1360 angstrom which may be due to 0.1 lambda 1356. Contrary to previous reports no evidence for He II lambda 1640 is found in the spectrum. An unresolved x ray source is detected at the location of the nucleus; its spectrum is well fitted by a power law of energy slope alpha approximately -0.5. These results further support the idea that NGC 4579 may contain a dwarf Seyfert nucleus.

Reichert, G. A.↗

Unusual spacecraft materials

For particularly innovative space exploration missions, unusual requirements are levied on the structural components of the spacecraft. In many cases, the preferred solution is the utilization of unusual materials. This trend is forecast to continue. Several hypothetic examples are discussed.

Post, Jonathan V.↗

Rapid induction bonding of composites, plastics, and metals

The Toroid Bonding Gun is and induction heating device. It is a self contained, portable, low powered induction welding system developed for bonding or joining plastic, ceramic, or metallic parts. Structures can be bonded in a factory or in a the field. This type of equipment allows for applying heat directly to the bond lines and/or to the adhesives without heating the entire structure, supports, and fixtures of a bonding assembly. The induction heating gun originally developed for use in the fabrication of space Gangs of bonders are now used to rapidly join composite sheet and structural components. Other NASA-developed applications of this bonding technique include the joining of thermoplastic composites, thermosetting composites, metals, and combinations of these materials.

Buckley, John D.↗