Search NASA⌕ Search

SEARCH · Search NASA

Results for “computational fluid dynamics simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69

risingMicrobubbleLattice

This code is a simulation case to be run with OpenFOAM, an open-source computational fluid dynamics software. A gmsh mesh file is also included. Specifically, this simulation demonstrates the transport of a single microbubble rising through an ordered lattice due to an applied flow. The bubble deforms as it squeezes through the pores of the lattice. Is

Guo, Jack [Lawrence Livermore National Laboratory ↗

Computational Analysis on the Effects of High-lift Propellers and Wingtip Cruise Propellers on X-57 Airplane

This study presents the computational study of the effects of high-lift system and wingtip-mounted cruise propellers on the flow physics and forces and moments of the X-57 Mod III/Mod IV configuration. Results were compared against previously published data on the powered-off configuration to determine the performance benefit. Simulations were performed using four different computational fluid dynamics solvers: STAR-CCM+, Launch Ascent Vehicle Aerodynamics, Kestrel, and USM3D. The high-lift system was shown to increase lift and lift-curve slope of the airplane. Additionally, the high-lift system was shown to increase the maximum lift coefficient and improve flow separation behavior at high anglesof-attack. Wingtip-mounted cruise propellers were shown to decrease the drag of the airplane. Simulation results showed that the drag decreased with increased thrust generated by the wingtip cruise propellers. The primary factor of the decrease in drag was a result of reduction in pressure drag of the wing. At the thrust setting of 230.1 lbf, results showed a reduction of 49-drag counts.

Seung Y. Yoo↗

CFD Approaches for Simulation of Wing-Body Stage Separation

A collection of computational fluid dynamics tools and techniques are being developed and tested for application to stage separation and abort simulation for next-generation launch vehicles. In this work, an overset grid Navier-Stokes flow solver has been enhanced and demonstrated on a matrix of proximity cases and on a dynamic separation simulation of a belly-to-belly wing-body configuration. Steady cases show excellent agreement between Navier-Stokes results, Cartesian grid Euler solutions, and wind tunnel data at Mach 3. Good agreement has been obtained between Navier-Stokes, Euler, and wind tunnel results at Mach 6. An analysis of a dynamic separation at Mach 3 demonstrates that unsteady aerodynamic effects are not important for this scenario. Results provide an illustration of the relative applicability of Euler and Navier-Stokes methods to these types of problems.

Buning, Pieter G.↗

Computation of incompressible viscous flows through artificial heart devices with moving boundaries

The extension of computational fluid dynamics techniques to artificial heart flow simulations is illustrated. Unsteady incompressible Navier-Stokes equations written in 3-D generalized curvilinear coordinates are solved iteratively at each physical time step until the incompressibility condition is satisfied. The solution method is based on the pseudo compressibility approach and uses an implicit upwind differencing scheme together with the Gauss-Seidel line relaxation method. The efficiency and robustness of the time accurate formulation of the algorithm are tested by computing the flow through model geometries. A channel flow with a moving indentation is computed and validated with experimental measurements and other numerical solutions. In order to handle the geometric complexity and the moving boundary problems, a zonal method and an overlapping grid embedding scheme are used, respectively. Steady state solutions for the flow through a tilting disk heart valve was compared against experimental measurements. Good agreement was obtained. The flow computation during the valve opening and closing is carried out to illustrate the moving boundary capability.

Kiris, Cetin↗

Validation of finite element analysis strategy to investigate acoustic levitation in a two-axis acoustic levitator

A two-axis acoustic levitator can be used to generate a standing pressure wave capable of levitating solid and liquid particles at appropriate input conditions. This work proposes a simulation framework to investigate the two-axis levitation particle stability using a commercial, computational fluid dynamics software based on the harmonic solution to the acoustic wave equation. The simulation produced predictions of the standing wave that include a strong "+" shaped pattern of nodes and anti-nodes that are aligned with the levitator axes. To verify the simulation, a levitator was built and used to generate the standing wave. The field was probed with a microphone and a motorized-scanning system. After scaling the simulated pressure to the measured pressure, the magnitudes of the sound pressure level at corresponding high-pressure locations were different by no more than 5%. This is the first time a measurement of a two-axis levitator standing pressure wave has been presented and shown to verify simulations. Furthermore, as an additional verification, the authors consulted high speed camera measurements of a reference-levitator transducer, which was found to have a maximum peak-to-peak displacement of 50 +/- 5 mu m. The reference-levitator is known to levitate water at 160 dB. The system for this work was simulated to match the operation of the reference-levitator so that it produced sound pressure levels of 160 dB. This pressure was achieved when the transducer maximum peak-to-peak displacement was 50.8 mu m. The agreement between the two levitators' displacements provides good justification that the modeling approach presented here produces reliable results.

2 axis levitator↗

Experimental Pressure Measurements on Hydropower Turbine Runners

The range of hydrodynamic operating conditions to which the turbine is exposed results in significant pressure fluctuations on both the pressure and suction sides of the blades. Understanding these dynamic pressures has a range of applications. Structurally, the resulting dynamic loads are significant in understanding the design life and maintenance schedule of the bearing, shafts and runner components. The pulsing pressures have also been seen to have a detrimental effect on the surface condition of the blades. Biologically, the pressure gradients and pressure extremes are the primary driver of barotrauma for fish passing through hydroturbines. Improvements in computational fluid dynamics (CFD) can be used to simulate such unsteady pressures in the regions of concern. High frequency model scale and prototype measurements of pressures at the blade are important in the validation of these models. Experimental characterization of pressure fields over hydroturbine blades has been demonstrated by a number of studies which using multiple pressure transducers to map the pressure contours on the runner blades. These have been performed at both model and prototype scales, often to validate computational models of the pressure and flow fields over the blades. This report provides a review of existing studies in which the blade pressure was measured in situ. The report assesses the technology for both model and prototype scale testing. The details of the primary studies in this field are reported and used to inform the types of hardware required for similar experiments based on the Ice Harbor Dam owned by the US Corps of Engineers on the Snake River, WA, USA. Such a study would be used to validate the CFD performed for the BioPA.

13 HYDRO ENERGY↗

CFD simulations of Molten Salt Fast Reactor core cavity flows

Computational Fluid Dynamics (CFD) has become increasingly important in the research and development of advanced nuclear reactors. Here, in the current study, extensive CFD simulations were conducted for the coolant flow in Molten Salt Fast Reactor (MSFR) core models using the state-of-the-art spectral element flow solver Nek5000 and multiscale coarse-mesh thermal-hydraulic software Pronghorn. The underlying motivation is to seek an in-depth understanding of how the internal velocity distribution can be influenced by the MSFR core cavity shape, the Reynolds number, turbulence modeling options and the inlet boundary conditions. The CFD techniques involved in this investigation range from coarse-mesh CFD, RANS modeling, to the high-fidelity LES calculations. Specifically, a series of RANS simulations were performed for the 2-D axisymmetric core model and 3-D wedge domains to study the flow distribution inside the MSFR core. It is observed that a proper representation of the MSFR inlet channel duct is important for the prediction of internal flow distribution. It is also showcased here how researchers can leverage the Nek5000 CFD results to calibrate more efficient coarse-mesh CFD tools, like Pronghorn, for the actual MSFR design needs. Moreover, this paper highlights a 3-D LES model for an entire MSFR core using the spectral element method and demonstrates the feasibility of this modeling approach. The readiness and potential limitations of the RANS approach are examined with respect to the high-fidelity LES simulations. The present investigation lays a solid foundation as we are leveraging the high-fidelity CFD capabilities to inform MSFR design efforts.

97 MATHEMATICS AND COMPUTING↗

Computation of the National Renewable Energy Laboratory Phase-VI Rotor in Pitch Motion during Standstill

Previously, computational fluid dynamics (CFD) computations of dynamic stall on wind turbine blades have been performed for stand still conditions with moderate success by among others the present authors. In the present work, numerical investigations are performed to illustrate the possibilities of state of the art CFD methods for this problem, including the numerical requirements as time-step and grid resolution. Additionally, the effect of different types of modeling is investigated, ranging from fully turbulent Reynolds-averaged Navier-Stokes (RANS), transitional RANS, to transitional delayed detached-eddy simulation computations. The investigation indicates that detailed information and fair agreement with measurements can be obtained.

17 WIND ENERGY↗

A thin-walled composite beam model for light-weighted structures interacting with fluids

A thin-walled beam model is proposed for structures of variable cross-section, which can be either open or closed and includes multicellular cross-sections with either isotropic or orthotropic materials. The proposed model does not require any priori definition of cross-sectional warping which instead results from the solution of the problem. To achieve that a special deformation pattern is superimposed on the bending deformation described by Euler–Bernoulli beam theory. All sectional properties are automatically incorporated in the analysis as a result of the usual variational formulation of the system of equations. The proposed model is specifically designed to simulate the dynamics of wind/hydrokinetic turbine blade with low computational cost, especially in fluid–structure interaction (FSI) simulation. A number of test cases have been carried out to validate the proposed structural model which show good agreement between the results obtained her e and the solutions available in literature. Finally, FSI simulation of a hydrokinetic blade under field condition is carried out to illustrate the capability of the current thin-walled beam model in practice.

42 ENGINEERING↗

Internal air flow analysis of a bladeless micro aerial vehicle hemisphere body using computational fluid dynamic

This paper explain the analysis of internal air flow velocity of a bladeless vertical takeoff and landing (VTOL) Micro Aerial Vehicle (MAV) hemisphere body. In mechanical design, before produce a prototype model, several analyses should be done to ensure the product's effectiveness and efficiency. There are two types of analysis method can be done in mechanical design; mathematical modeling and computational fluid dynamic. In this analysis, I used computational fluid dynamic (CFD) by using SolidWorks Flow Simulation software. The idea came through to overcome the problem of ordinary quadrotor UAV which has larger size due to using four rotors and the propellers are exposed to environment. The bladeless MAV body is designed to protect all electronic parts, which means it can be used in rainy condition. It also has been made to increase the thrust produced by the ducted propeller compare to exposed propeller. From the analysis result, the air flow velocity at the ducted area increased to twice the inlet air. This means that the duct contribute to the increasing of air velocity.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Lattice Boltzmann and Navier-Stokes Cartesian CFD Approaches for Airframe Noise Predictions

Lattice Boltzmann (LB) and compressible Navier-Stokes (NS) equations based computational fluid dynamics (CFD) approaches are compared for simulating airframe noise. Both LB and NS CFD approaches are implemented within the Launch Ascent and Vehicle Aerodynamics (LAVA) framework. Both schemes utilize the same underlying Cartesian structured mesh paradigm with provision for local adaptive grid refinement and sub-cycling in time. We choose a prototypical massively separated, wake-dominated flow ideally suited for Cartesian-grid based approaches in this study - The partially-dressed, cavity-closed nose landing gear (PDCC-NLG) noise problem from AIAA's Benchmark problems for Airframe Noise Computations (BANC) series of workshops. The relative accuracy and computational efficiency of the two approaches are systematically compared. Detailed comments are made on the potential held by LB to significantly reduce time-to-solution for a desired level of accuracy within the context of modeling airframes noise from first principles.

Airframe Noise Prediction↗

Simulation studies on the standing and traveling wave thermoacoustic prime movers

Thermoacoustic systems have been a focus of recent research due to its structural simplicity, high reliability due to absence of moving parts, and can be driven by low grade energy such as fuel, gas, solar energy, waste heat etc. There has been extensive research on both standing wave and traveling wave systems. Towards the development of such systems, simulations can be carried out by several methods such as (a) solving the energy equation, (b) enthalpy flow model, (c) DeltaEC, a free software available from LANL, USA (d) Computational Fluid Dynamics (CFD) etc. We present here the simulation studies of standing wave and traveling wave thermoacoustic prime movers using CFD and DeltaEC. The CFD analysis is carried out using Fluent 6.3.26, incorporating the necessary boundary conditions with different working fluids at different operating pressures. The results obtained by CFD are compared with those obtained using DeltaEC. Also, the CFD simulation of the thermoacoustically driven refrigerator is presented.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Heat Integration Optimization and Dynamic Modeling Investigation for Advancing the Coal-Direct Chemical Looping Process

The purpose of the project is to address the optimization and startup operation of a modular coal direct chemical looping (CDCL) combustion system integrated with a steam cycle for power generation to reduce the risks involved in further scale-up of the technology. The modular reactor design of the CDCL process provides flexibility in the fabrication of the reactor and in its operating capacity (i.e. turndown ratio) at the cost of a more complex heat exchange network (HEN) design and integration. To address the technology gaps and advance the efficiency and economic feasibility of the CDCL technology, the project will perform a detailed and comprehensive analysis of the integration of a modular CDCL reactor system and a steam cycle system under both static and transient conditions via HEN process performance simulations and system dynamic modeling, respectively. The scope of work consists of 1) Experimental and computational studies of the CDCL combustor reactor 2) Comprehensive static (i.e. steady-state) system HEN design analysis in CDCL 550 MWe commercial unit for power generation and 3) Dynamic modeling of site specific design of 10MWe CDCL large pilot plant. The project team has successfully developed and validated a kinetic model for the oxidation of oxygen carriers in the combustor using the unreacted shrinking core model (UCSM). The model is capable of capturing the oxidation kinetics of fully or partially reduced oxygen carrier particles. A computational fluid dynamics (CFD) model is developed to simulate the hydrodynamics, heat transfer, and chemical reaction occurring in the CDCL combustor. The model is developed in MFIX and ANSYS Fluent. Key aspects of CDCL combustor operation, including heat transfer, oxygen carrier oxidation, and the transport of oxygen carrier particles, are simulated using this CFD model. The HEN for a commercial scale 550 MWe CDCL power plant is simulated and optimized using ASPEN Plus. Practical design considerations are incorporated based on industrial experiences. The performance and cost for the commercial CDCL plant is updated based on these analyses. A dynamic model for the 10 MWe CDCL pilot plant is developed in ProTRAX simulation software. The model is based on the pilot plant design developed in project DE-FE0027654 “10 MWe CDCL Large Pilot Plang – Pre-FEED Study” and the steam cycle data obtained from Dover Light & Power plant. The transient behaviors during pilot plant load variation are simulated using the dynamic model.

01 COAL, LIGNITE, AND PEAT↗

Pore-scale CFD simulations of clay mobilization in natural porous media due to fresh water injection

The present work investigates mechanisms of permeability impairment as a result of low-salinity fluid injection into brine-saturated porous media containing dispersible clays. Here, we present a computational fluid dynamics model at the pore-scale to simulate detachment, migration and straining of fine particles in porous media. The model uses an immersed boundary method to simulate the motion of clay fines in a fluid. In addition to the hydrodynamic forces, we model the Derjaguin-Landau-Verwey-Overbeek forces (DLVO) between clay fines and grains. Our simulations show the impact of the injected fluid's salinity and velocity on the concentration of clay fines retained on the grain surface. We see clay particles dislodging from the grain surface in clusters of up to 12 particles. Our simulation results also demonstrate clogging of narrow pore spaces by the detached particles from the grain surfaces.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

High-resolution time-resolved experiments on mixing and entrainment of buoyant jets in stratified environments

Fluid jets interacting with a stratified layer play an important role in the safety of several reactor designs. In the containment of nuclear power plants, fluid jets dominate the transport and mixing of gaseous species and consequent hydrogen distribution in case of a severe accident. The mixing phenomena in the containment are driven by buoyant high-momentum injections (jets) and low momentum injection plumes. Mixing near the postulated break is initially dominated by high flow velocities. Plumes with moderate flow velocities are instead relevant in the break compartment during the long-term pressurization phase, or in any of the apertures between two connected compartments if the mass flows are sufficiently high and the density differences between efflux and ambient are sufficiently low. Phenomena of interest include free plumes (as produced by the efflux from the break compartment in a larger room or directly from a break flow), wall plumes (such those produced by low mass flows through inter-compartment apertures), and propagating stratification fronts in the ambient (for any stably stratified conditions). These phenomena have been highly ranked about nuclear reactor design, especially regarding of safety protocols. During a Pressurized Thermal Shock (PTS) scenario, the interaction between the cold ECCS injection plume and the stratified fluid present in the cold (or hot) leg is important in order to determine the temperature at the time-dependent temperature at the inlet of the reactor pressure vessel (RPV) and the potential to cause a thermal shock on the RPV wall. In sodium-cooled fast reactors (SFRs), core channels are typically hydro-dynamically isolated so that there exists a considerable temperature variation at the exit of adjacent fuel assemblies. All the above phenomena are characterized by the interaction of buoyant jets with the stratified flow. In stratified layers baroclinic forces create significant redistribution of turbulent kinetic energy and scales, which leads to anisotropy. This important physical phenomenon is highly three dimensional and is challenging to capture even with high-fidelity CFD simulations, due in part to lack of sufficiently resolved validation data. Furthermore, the experimental data available in the open literature do not feature the level of fidelity needed for an extensive validation of turbulence models in lower order CFD. To shed new lights into the crucial phenomena object of the present research project, it was proposed to conduct coordinated experiments and simulations at the University of Michigan and the George Washington University. The project has resulted in an experimental database of high-resolution time-resolved measurements of jets in uniform and stratified environments. The novel experimental data will be used to validate computational fluid dynamic (CFD) codes, including both Large Eddy Simulations (LES) and unsteady Reynolds-averaged Navier-Stokes equations (URANS) methodologies. In the Experimental and Multiphase flow (ECMF) laboratory at Univerisity of Michigan, we built two experimental facilities to investigate also the effect of scaling. The first facility, DESTROJER (DEnsity Stratified Turbulent ROund free Jet ExpeRiment), featuring a contoured jet nozzle with a diameter of D=12.7mm and a 1m×1m×1m cubic tank, which is made of acrylic glass for optical access. The ratio between the tank width and the nozzle diameter is equal to 78, which ensures that there is no direct interaction between the jet and the side walls. A second, modular experimental facility, features three different tank sizes of size 10×10×30, 20×20×30, 30×30×30 cm3 respectively (all tanks have the same height of 30 cm), and a jet diameter of 2mm. For the modular facility, tank-to-nozzle ratio of 50, 100, and 150 are obtained respectively. Experiments with different-density jet impactions and sharp interface with a density difference of 3.16% In the Laboratory at George Washington University, complementary experiments have been carried out at a facility featuring the same dimensions as DESTROYER. Experiments with different jet diameters have been carried out as well. High-resolution time-resolved measurements have been performed at all facilities using high-speed particle image velocimetry (PIV) and planar laser-induced fluorescence (PLIF). In this way, simultaneous measurements of velocity and density fields have been carried out. At the University of Michigan, wire-mesh sensors have been designed and built to gather high-resolution, time-dependent data of the stratified front in the tank. These measurements are important to provide accurate initial conditions for the CFD simulations. An important outcome of the project has been the development of novel techniques to achieve refractive index matching (RIM) of acqueous solutions with high density differences. RIM is crucial if optical techniques such as PIV are used to measure velocity fields. Previous to this project, experiments up to 3% density difference had been reported in the literature. With the methodology developed in this project, we have been able to push the envelop to density differences up to 9%. The experiments have been used to validate Reynolds Averaged Navier-Stokes (RANS) turbulence models and Large Eddy Simulations (LES) models. Both NEK5000 and the commercial CFD code STAR-CCM+ have been used. The experimental data will be made available to the community through the NE-KAMS databasehave been successfully conducted in the scaled facility.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Multiscale model based design of an energy–intensified novel adsorptive reactor process for the water gas shift reaction

In this work, an adsorptive reactor (AR) process is considered that can energetically intensify the water gas shift reaction (WGSR). To best understand AR process behavior, a multiscale, dynamic, process model is developed. This multiscale model enables the quantification of catalyst and adsorbent effectiveness factors within the reactor environment, obliviating the commonly employed assumption that these factors are constant. Simulations of the AR's alternating adsorption-reaction/desorption operation, using the proposed model, illustrate rapid convergence to a long-term periodic solution. The obtained simulation results quantify the influence of key operating conditions and design parameters (e.g., reactor temperature/pressure, W cat /F CO , W ad /F CO , F H2O /F CO ratios, and pellet size) on the AR's behavior. Finally, they also demonstrate, for pellet diameters used at the industrial scale, significant temporal and axial variation of the catalyst/adsorbent pellet effectiveness factors. Finally, the energetic intensification benefits of the proposed AR process over conventional WGSR packed-bed reactors are quantified.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Three-Dimensional Numerical Modeling of Initial Mixing of Thermal Discharges at Real-Life Configurations

A three-dimensional Reynolds-averaged Navier-Stokes (RANS) computational fluid dynamics (CFD) model is developed for simulating turbulent mixing in the near-field of thermal discharge at real-life geometrical configurations. The domain decomposition method with the multi-level embedded overset grids is employed to handle the complexity of real-life diffusers as well as to efficiently account for the large disparity of length scales arising from the relative size of the ambient river reach and the typical diffuser diameter.

97 MATHEMATICS AND COMPUTING↗

Numerical Study of Combustor-Turbine Interactions Considering a Two-Stage High-Pressure Turbine

In this study, preliminary results are presented from the Open National Combustion Code (OpenNCC) applied to the two-stage high-pressure turbine (HTP) from the energy efficient engine (E3) program. Although the combustor is designed for efficient fuel–air mixing and a relatively uniform exit temperature profile, temporal and spatial variation in combustor exit conditions inevitably lead to hot-streaks in the HPT. These hot streaks can cause local hot spots on the HPT blade surfaces that reduce blade life. To improve understanding of these effects and the overall design of combustor and HPT, we are developing a fully-coupled combustor-turbine computational fluid dynamics (CFD) capability. Previous work has simulated the E3 combustor at the simulated Sea-Level Take-off (SLTO) condition (P41 = 2.4 [atm]) with and without the first-stage HPT stator included. This work addresses HPT simulations using inflow conditions based on previous simulation results of the E3 combustor, as well as investigating the effects of spatial and temporal temperature non-uniformity of the combustor-exit flow on the HPT performance for a more realistic SLTO (P41 = 27.4 [atm])). First, we analyze existing results from the combustor and the HPT 1st-stage stator simulation, where the unsteady hot gas coming out of the combustor exit travels between the stationary stators and then directly exits the computational domain (i.e., no effect from the rotors). Second, we simulate the HPT including the 1st and 2nd stage stators and rotors with the time-averaged, spatially-nonuniform inflow to the HPT taken from the combustor (with HPT 1st-stage stators) solution. Differences in simulations results for the flow field in the 1st-stage stator region are presented. The results of these two simulations (combustor and HPT simulated in a sequential manner) will be compared to a fully-coupled EEE combustor/HPT simulation to understand the impacts of fully-coupled simulations on combustor and HPT performance for two different operating conditions.

LES↗