Search NASA⌕ Search

SEARCH · Search NASA

Results for “full scale testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69

A Comparison of Pressure Measurements Between a Full-Scale and a 1/16-Scale F/A-18 Twin Tail During Buffet

In 1993, tail buffet tests were performed on a full-scale, production model F/A-18 in the 80-by-120 Foot Wind Tunnel at NASA Ames Research Center. Steady and unsteady pressures were recorded on both sides of the starboard vertical tail for an angle of attack range of 20 to 40 degrees and at a sideslip range of -16 to 16 degrees at freestream velocities up to 100 knots (Mach 0.15, Reynolds number 1.23 x 10(exp 7)). The aircraft was equipped with removable leading edge extension (LEX) fences that are used in flight to reduce tail buffet loads. In 1995, tail buffet tests were performed on a 1/6-scale F-18 A/B model in the Transonic Dynamics Tunnel (TDT) at NASA Langley Research Center. Steady and unsteady pressures were recorded on both sides of both vertical tails for an angle-of-attack range of 7 to 37 degrees at freestream velocities up to 65 knots (Mach 0.10). Comparisons of steady and unsteady pressures and root bending moments are presented for these wind-tunnel models for selected test cases. Representative pressure and root bending moment power spectra are also discussed, as are selected pressure cross-spectral densities.

Moses, Robert W.↗

A Comparison of Pressure Measurements Between a Full-Scale and a 1/6-Scale F/A-18 Twin Tail During Buffet

In 1993, tail buffet tests were performed on a full-scale, production model F/A-18 in the 80 x 120-foot Wind Tunnel at NASA Ames Research Center. Steady and unsteady pressures were recorded on both sides of the starboard vertical tail for an angle-of-attack range of 20 to 40 degrees and at a sideslip range of -1 6 to 16 degrees at freestream velocities up to 100 knots (Mach 0.15, Reynolds number 1.23 x 10(exp 7). The aircraft was equipped with removable leading edge extension (LEX) fences that are used in flight to reduce tail buffet loads. In 1995, tail buffet tests were performed on a 1/6-scale F-18 A/B model in the Transonic Dynamics Tunnel (TDT) at NASA Langley Research Center. Steady and unsteady pressures were recorded on both sides of both vertical tails for an angle-of-attack range of 7 to 37 degrees at freestream velocities up to 65 knots (Mach 0.10). Comparisons of steady and unsteady pressures and root bending moments are presented for these wind-tunnel models for selected test cases. Representative pressure and root bending moment power spectra are also discussed, as are selected pressure cross-spectral densities.

Moses, Robert W.↗

Development of High-Performance Ni-base Alloys for Gas Turbine Wheels Using a Coprecipitation Approach (Final Technical Report)

In this project, a synergistic approach involving experiments informed by modelling was used to develop γ'/γ'' coprecipitation-strengthened Ni-base superalloys for land-based gas turbine wheels. In thick sections of such turbine wheels, the slow cooling rate normally observed, as well as variations in cooling rate could potentially result in drastically inhomogeneous and coarsened microstructure. Thus, ten alloy compositions were selected based on coprecipitation and sluggish γ’ growth and coarsening during three iterations of alloy development, assisted by extensive CALPHAD modeling. Phase equilibrium calculations, informed by the characterization of early alloys, were successful in predicting suitable aging treatments to obtain bimodal coprecipitate distribution in several alloys. These aging treatments were applied to the subsequent round of alloys and the resulting microstructures were characterized in detail. Two different cooling rates were used during each of these heat treatments to simulate the range of cooling rates observed in a thick section forging. The microstructures were used to calibrate a multi-phase field model (MPF), which was used to study the formation mechanisms of various coprecipitate morphologies observed in the experiments. Following this, the most promising alloys in each round were selected and studied using high temperature tensile and creep tests. Considering that a slower cooling rate would lead to a strength debit, while a faster cooling rate might lead to a decline in creep rupture life of a full-scale wheel, tensile tests were carried out for slower cooled samples, while creep tests were carried out for faster cooled samples. The deformation microstructures were then characterized using advanced characterization techniques such as Diffraction Contrast-Scanning Transmission Electron Microscopy (DC-STEM) and Electron Channeling Contrast Imaging (ECCI). Further, a mean-field creep model was developed and calibrated using these experimental findings to predict long-term creep behavior of these coprecipitation-strengthened alloys.

36 MATERIALS SCIENCE↗

Rotor Dynamic State and Parameter Identification from Hovering Transients

State and parameter identifications based on a form of the maximum likelihood method are applied to the problem of extracting linear perturbation models, including rotor dynamic inflow effects, from transient blade flapping measurements. The estimation method is first studied in computer simulations and then applied to cyclic pitch stirring transients generated with a four-bladed rotor model operating in hovering trim conditions. The analytical perturbation models extracted from the transient test results are compared with transient and frequency response tests not used in the state and parameter identification. The identified analytical perturbation model is also compared with a simple theory. The method that is applicable both to small scale and full scale dynamic rotor testing is being extended to perturbations from forward flight trim conditions.

Hohenemser, K. H.↗

Forced Mixer Nozzle Optimization

Computational fluid dynamic (CFD) and computational acoustic analyses (CAA) were performed for a TFE731-40 compound nozzle, a TFE731-60 mixer nozzle and an Energy Efficient Engine (E(sup 3)) mixer nozzle for comparison with available data. The CFD analyses were performed with a three dimensional, Navier-Stokes solution of the flowfield on an unstructured grid using the RAMPANT program. The CAA analyses were performed with the NASA Glenn MGB program using a structured grid. A successful aerodynamic solution for the TFE731-40 compound nozzle operating statically was obtained, simulating an engine operating on a test stand. Analysis of the CFD results of the TFE731-40 with the MGB program produced predicted sound power levels that agree quite well with the measured data front full-scale static engine tests. Comparison of the predicted sound pressure with the data show good agreement near the jet axis, but the noise levels are overpredicted at angles closer to the inlet. The predicted sound power level for the TFE731-60 did not agree as well with measured static engine data as the TFE731-40. Although a reduction in the predicted noise level due to the mixed flow was observed, the reduction was not as significant as the measured data. The analysis of the V2 mixer from the E(sup 3) study showed that peak temperatures predicted in the mixer exit flowfield were within 5 percent of the values measured by the exit probes. The noise predictions of the V2 mixer nozzle tended to be 3-5 dB higher in peak noise level than the measurements. In addition, the maximum frequency of the noise was also overpredicted. An analysis of the 3 candidate mixer nozzle configurations demonstrated the feasibility of using centerbody lobes and porosity to improve mixing efficiency. A final configuration was designed with a predicted thermal mixing efficiency that was 5 percent higher than the 3 candidate mixers. The results of the MGB noise calculations show that the final design will exceed the design goal of a 3 dB reduction in noise as compared to the baseline TFE731-40.

Sheoran, Yogi↗

Possible Mechanisms for Turbofan Engine Ice Crystal Icing at High Altitude

A thermodynamic model is presented to describe possible mechanisms of ice formation on unheated surfaces inside a turbofan engine compression system from fully glaciated ice crystal clouds often formed at high altitude near deep convective weather systems. It is shown from the analysis that generally there could be two distinct types of ice formation: (1) when the "surface freezing fraction" is in the range of 0 to 1, dominated by the freezing of water melt from fully or partially melted ice crystals, the ice structure is formed from accretion with strong adhesion to the surface, and (2) when the "surface melting fraction" is the range of 0 to 1, dominated by the further melting of ice crystals, the ice structure is formed from accumulation of un-melted ice crystals with relatively weak bonding to the surface. The model captures important qualitative trends of the fundamental ice-crystal icing phenomenon reported earlier (Refs. 1 and 2) from the research collaboration work by NASA and the National Research Council (NRC) of Canada. Further, preliminary analysis of test data from the 2013 full scale turbofan engine ice crystal icing test (Ref. 3) conducted in the NASA Glenn Propulsion Systems Laboratory (PSL) has also suggested that (1) both types of ice formation occurred during the test, and (2) the model has captured some important qualitative trend of turning on (or off) the ice crystal ice formation process in the tested engine low pressure compressor (LPC) targeted area under different icing conditions that ultimately would lead to (or suppress) an engine core roll back (RB) event.

Crystal Icing↗

UH-60A Airloads Flight Test Program: Data Counter 8534

During the period between July 1993 and February 1994 the data collection portion of the UH-60A Airloads Program was conducted. At the time, UH-60A Airloads Program was the most comprehensive and data rich rotorcraft flight test program that NASA and the Army had ever attempted. It was part of the Modern Technology Rotor Program, where several different rotors were to be tested in small and full-scale wind tunnels combined with flight testing. This would allow for comparison between the various tests and comprehensive analyses. Results were to be stored in a comprehensive, easily accessed, database know as Tilt Rotor Engineering Database System, TRENDS. With over 30 years of rotor testing experience, the goal of NASA and the Army was to collect a wide and extensive amount of data to improve the understanding of rotors and prediction codes.

Kufeld, Robert M.↗

UH-60A Airloads Flight Test Program: Data Counter 8513

The data collection portion of the UH-60A Airloads Flight Test Program was conducted between July 1993 and February 1994. At the time, the UH-60A Airloads Program was the most comprehensive and data-rich rotorcraft flight test program that NASA and the U.S. Army had ever attempted. It was part of the Modern Technology Rotors Program, where several different rotors were tested in small- and full-scale wind tunnels combined with flight testing. The UH-60A portion of this program allowed for comparison between other tests performed and served as a scientific quality database for validating current and new computational and simulation models. The UH-60A flight test data was stored in a comprehensive, easily accessed database known as the Tilt Rotor Engineering Database System, or TRENDS. With over 30 years of rotor testing experience, NASA and the Army’s goal of the Airloads Flight Test Program was to collect data for a wide range of operating conditions and provide an extensive amount of data to improve the understanding of rotors and validate and improve prediction codes. This report presents the entire archived data set from Counter 8513 (Run 85, point 13) from the UH-60A Airloads Flight Test Program. There were 1,078 total data set counters acquired and archived during 57 accumulated flight hours and 31 research flights. Over 900 counters were research flight data acquisition data points. Counter 8513 is a low-speed, level-flight test condition.

Kufeld, Robert M.↗

UH-60A Airloads Flight Test Program: Data Counter 9505

The data collection portion of the UH-60A Airloads Flight Test Program (ref. 1) was conducted between July 1993 and February 1994. At the time, the UH-60A Airloads Program was the most comprehensive and data-rich rotorcraft flight test program that NASA and the U.S. Army had ever attempted. It was part of the Modern Technology Rotors Program (ref. 2), where several different rotors were tested in small- and full-scale wind tunnels combined with flight testing. The UH-60A portion of this program allowed for comparison between other tests performed and served as a scientific quality database for validating current and new computational and simulation models. The UH-60A flight test data was stored in a comprehensive, easily accessed database known as the Tilt Rotor Engineering Database System, or TRENDS (ref. 3). With over 30 years of rotor testing experience (ref. 4), NASA and the Army’s goal of the Airloads Flight Test Program was to collect data for a wide range of operating conditions, and to provide an extensive amount of data to improve the understanding of rotors and validate and improve prediction codes. This report presents the entire archived data set from Counter 9505 (Run 95, point 5) from the UH-60A Airloads Flight Test Program. There were 1,078 total data set counters acquired and archived during 57 accumulated flight hours and 31 research flights. Over 900 counters were research flight data acquisition data points. Counter 9505 is a low altitude, moderate airspeed, level-flight test condition. Ground acoustic microphone data was acquired for this counter but the acoustic data is not included in this report.

Kufeld, Robert M.↗

DHC-6 Twin Otter Tailplane Airfoil Section Testing in the Ohio State University 7x10 Wind Tunnel

Ice contaminated tailplane stall (ICTS) has been found to be responsible for 16 accidents with 139 fatalities over the last three decades, and is suspected to have played a role in other accidents and incidents. The need for fundamental research in this area has been recognized at three international conferences sponsored by the FAA since 1991. In order to conduct such research, a joint NASA/FAA Tailplane Icing Program was formed in 1994: the Ohio State University has played an important role in this effort. The program employs icing tunnel testing, dry wind tunnel testing, flight testing, and analysis using a six-degrees-of-freedom computer code tailored to this problem. A central goal is to quantify the effect of tailplane icing on aircraft stability and control to aid in the analysis of flight test procedures to identify aircraft susceptibility to ICTS. This report contains the results ot testing of a full scale 2D model of a tailplane section of NASA's Icing Research Aircraft, with and without ice shapes, in an Ohio State University 7 x 10 Low Speed wind tunnel in 1994. The results have been integrated into a comprehensive database of aerodynamic coefficients and stability and control derivatives that will permit detailed analysis of flight test results with the analytical computer program. The testing encompassed a full range of angles of attack and elevator deflections, as well as two velocities to evaluate Reynolds number effects. Lift, drag, pitching moment, and hinge moment coefficients were obtained. In addition. instrumentation for use during flight testing was verified to be effective, all components showing acceptable fidelity. Comparison of clean and iced airfoil results show the ice shapes causing a significant decrease in the magnitude of CLmax (from -1.3 to -0.64) and associated stall angle (from -18.6 deg to -8.2 deg). Furthermore, the ice shapes caused an increase in hinge moment coefficient of approximately 0.02, the change being markedly abrupt for one of the ice shapes. A noticeable effect of elevator deflection is that magnitude of the stall angle is decreased for negative (upward) elevator deflections. All these result are consistent with observed tailplane phenomena. and constitute an effective set of data for comprehensive analysis of ICTS

Hiltner, Dale↗

SEP solar array development testing

This paper describes the test program of a lightweight 25 kW solar array for solar electric propulsion. A full-scale development wing was made of aluminum with the containment box cover of graphite-epoxy, while the flight design array wing uses a graphite-epoxy structure. The full-scale continuous longeron array extension mast was tested for performance on a water table, and the full scale wing was functionally tested to demonstrate automatic containment box unlocking, wing extension, and retraction, blanket tensioning, and automatic application of blanket preload. The wing was then tested to the Shuttle acoustic environment, followed by a thermal/vacuum test in which the wing was extended and retracted at high and low temperature. Finally, the wing was tested in vibration with sine and random vibration environments.

Elms, R. V., Jr.↗

Space shuttle maneuvering engine reusable thrust chamber program. Task 11: Stability analyses and acoustic model testing data dump

The combustion stability characteristics of engines applicable to the Space Shuttle Orbit Maneuvering System and the adequacy of acoustic cavities as a means of assuring stability in these engines were investigated. The study comprised full-scale stability rating tests, bench-scale acoustic model tests and analysis. Two series of stability rating tests were made. Acoustic model tests were made to determine the resonance characteristics and effects of acoustic cavities. Analytical studies were done to aid design of the cavity configurations to be tested and, also, to aid evaluation of the effectiveness of acoustic cavities from available test results.

Oberg, C. L.↗

Development of High Temperature (>700°C) Molten Salt Pump Technology for Generation 3 Solar Power Tower Systems

Bearings are required for long-shafted pumps historically used in concentrating solar thermal power applications. For molten chloride salts, bearings for such service conditions are not commercially available, nor has a design been demonstrated to work. Therefore, a project was sponsored by the Department of Energy’s Solar Energy Technologies Office for the development and demonstration of a submerged bearing for use in chloride salt pumps. This project’s tasks covered the tribological testing of candidate materials and the design, fabrication, testing, and post-test analysis of full-scale salt-compatible bearings. This work expands upon previous work. The effects of potential particulate in the salt were investigated through tribological bench testing. Through 11 tests, the MgO particulate size and concentration in a molten chloride salt were varied, and the effects on friction, wear rate, and wear characteristics were recorded. Novel journal bearings for chloride salt service were designed and fabricated based on these results. The bearings were of a relevant scale (i.e., for a 1.5 in. pump shaft) to demonstrate the technology with respect to further scale-up. The bearings were made of Haynes 244 and Yttria Partially Stabilized Zirconia. A custom bearing test rig, salt tanks, and associated infrastructure (e.g., heaters, tanks, transfer lines, gas flow control) were designed, procured, and installed. A few issues were encountered in the system fabrication process, resulting in delay of the project schedule. The system was successfully fabricated and assembled. Heating, cover gas, and pump motor systems were integrated into the control logic. This progress of the bearing test system represents a significant step forward towards demonstrating this promising technology. Nevertheless, the project ended before testing of the full-scale bearings could be performed.

14 SOLAR ENERGY↗

Performance evaluation of a Terry GS-2 steam impulse turbine with air-water mixtures

Terry steam turbines are widely used in various industries because of their robust design. Within the nuclear power generation industry, they are used in the Reactor Core Isolation Cooling System to remove decay heat during reactor isolation events. During the Fukushima Daiichi nuclear power station disaster in Japan in 2011, the Reactor Core Isolation Cooling System and associated Terry turbine operated for over 70 hours in Unit 2; this runtime is well beyond the expected operating duration. Theories suggest the turbine was subjected to a two-phase inlet flow, which could degrade the turbine performance. In this work, an experimental test rig was constructed to test a full-scale Terry model GS-2 steam turbine under two-phase air/water flows. Steady-state efficiency and torque performance maps of the turbine were developed over a range of turbine inlet pressures (1.38–4.83 bar or 20–70 psia), air mass fractions (0.05–1.0) and rotational speeds up to 4000 RPM. Furthermore, turbine performance followed expected trends with torque varying linearly and efficiency varying quadratically with rotational speed. In addition, high-speed images of the two-phase flow entering the turbine were also analyzed to understand how changes in inlet pressure and air mass fraction affect the flow regime and homogenization. The present tests with air–water two-phase mixtures are an important step towards providing an understanding of the full-scale Terry turbine’s behavior and performance curves under two-phase conditions. The results of this work will be combined with air/water and steam/water data gathered using a small-scale Terry ZS-1 steam turbine in order to understand the scaling relationship between large and small size Terry turbines and fluid pairs. The combined data set will enable further development of analytical models over a wide range of conditions and may be used to provide technical justification for expanded use of the Terry turbines in nuclear power plant safety systems and other systems.

42 ENGINEERING↗

Assessment of Near-Term Fuel Screening and Qualification Needs for Nuclear Thermal Propulsion Systems

Nuclear thermal propulsion (NTP) is an in-space propulsion technology capable of both high specific impulse (850–1000 s) and thrust (44–1112 kN), which can help reduce trip times for crewed missions beyond low Earth orbit. NTP technology has been demonstrated during historic programs. Over 20 ground test reactor experiments were performed, which demonstrated the prototypic reactor operations, during the Nuclear Engine for Rocket Vehicle Application (NERVA)/Rover program (1955–1972). Although historical programs have shown that NTP is a viable in-space propulsion technology, developing NTP in modern programs is contingent on the development and qualification of ultrahigh-temperature nuclear fuel technologies that can withstand engine operating conditions. In historical NTP development programs such as NERVA/Rover, prototypic reactor/engine schemes were ground tested to assess the overall system feasibility and to qualify the reactor fuel forms for eventual flight systems. Although this approach is effective to verify fuel performance under prototypic conditions, relying solely on full-scale NTP reactor tests as the pathway for verifying or qualifying fuel is inefficient and cost prohibitive today. Additionally, modern nuclear licensing requirements state that before test reactor approval, reactor components and fuel elements should be qualified via non-nuclear (out-of-pile) and nuclear (in-pile) testing under representative operating conditions. Using this methodology, fuel matures as production scale fabrication methods are established, and as produced fuel performance is demonstrated. Here, this paper provides an overview of historical approaches to NTP fuel performance maturation, including fuel screening and qualification needs, and provides insight for establishing an efficient testing paradigm that can be implemented to rapidly and affordably develop NTP fuel forms for eventual qualification.

42 ENGINEERING↗

Large-Scale Advanced Prop-Fan (LAP)

In recent years, considerable attention has been directed toward improving aircraft fuel efficiency. Analytical studies and research with wind tunnel models have demonstrated that the high inherent efficiency of low speed turboprop propulsion systems may now be extended to the Mach .8 flight regime of today's commercial airliners. This can be accomplished with a propeller, employing a large number of thin highly swept blades. The term Prop-Fan has been coined to describe such a propulsion system. In 1983 the NASA-Lewis Research Center contracted with Hamilton Standard to design, build and test a near full scale Prop-Fan, designated the Large Scale Advanced Prop-Fan (LAP). This report provides a detailed description of the LAP program. The assumptions and analytical procedures used in the design of Prop-Fan system components are discussed in detail. The manufacturing techniques used in the fabrication of the Prop-Fan are presented. Each of the tests run during the course of the program are also discussed and the major conclusions derived from them stated.

Degeorge, C. L.↗

On-orbit Systems Identification of Flexible Spacecraft Technol., 1984, Pt. 2 p 465-481

Future spacecraft include configurations which are too flexible to be adequately tested prior to flight and which will require on-orbit systems identification to ensure safe operation of the flight control system. The structural dynamics model will evolve and its accuracy will improve in stages as ground tests of full-scale components and replica-scale models are performed. State Space Modeling and Conditional Maximum Likelihood Parameter Estimation methodology can provide the formal probability-based framework for the process of upgrading a model as additional test results are obtained. Although the number of unknown parameters can be reduced by the use of canonical forms for the stability matrix, the number of unknown model parameters quickly becomes unmanageable unless advantage is taken of the relationship of a much fewer number of global model parameters. Distributed parameter systems or partial differential equation models are one way to take advantage of such global parameters to reduce the number of unknown model parameters.

Taylor, L.↗

Blade Testing Equipment Development and Commercialization: Cooperative Research and Development (Final Report)

Blade testing is required to meet wind turbine design standards, reduce machine cost, and reduce the technical and financial risk of deploying mass-produced wind turbine models. NREL's National Wind Technology Center (NWTC) in Colorado is the only blade test facility in the U.S. capable of performing full-scale static and fatigue testing of multi-megawatt-scale wind turbine blades. Rapid growth in wind turbine size over the past two decades has outstripped the size capacity of the NWTC blade test facility leaving the U.S. wind industry without a suitable means of testing blades for large land-based and offshore turbines. This CRADA will develop and commercialize testing technologies and test equipment, including scaling up, value engineering, and testing of equipment to be used at blade testing facilities in the U.S. and around the world.

17 WIND ENERGY↗