SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Electrodes are prepared by vacuum deposition of platinum on nickel substrate with conventional vapor-deposition apparatus. Amount of platinum loaded on substrate can be veried by changing exposure time during deposition. These electrodes are significantly more effective than conventional oxygen electrodes.
A static stability augmentation system (SSAS) with angle-of-attack, pitch-rate, and forward-speed feedback is used to stabilize control-configured rigid vehicles with relaxed static stability. Airplane configurations include a baseline configuration and two representative control-configured vehicle configurations. The first statically unstable configuration has baseline geometry and an aft center of gravity; the second statically unstable configuration has reduced tail length and area and a forward neutral point. Stability, flying-qualities, and maneuverability requirements are imposed on the airplane-SSAS systems. Turbulence responses of the rigid airframe and tail loads are examined in terms of configuration changes for a given control law and in terms of control law changes for a given configuration.
Current domestic and international air cargo operations are studied and the characteristics of 1990 air cargo demand are postulated from surveys conducted at airports and with shippers, consignees, and freight forwarders as well as air, land, and ocean carriers. Simulation and route optimization programs are exercised to evaluate advanced aircraft concepts. The results show that proposed changes in the infrastructure and improved cargo loading efficiencies are as important enhancing the prospects of air cargo growth as is the advent of advanced freighter aircraft. Potential reductions in aircraft direct operating costs are estimated and related to future total revenue. Service and cost elasticities are established and utilized to estimate future potential tariff reductions that may be realized through direct and indirect operating cost reductions and economies of scale.
Results of wind tunnel testing of a multicyclic controllable twist rotor at several flight conditions and advance ratios of 0.22 and 0.33 are evaluated. It is found that blade flatwise bending moments and root control actuator loads (fixed system) can be reduced with multicyclic control. Flatwise bending moment reductions of 22-30% with concurrent 83% reductions in control loads were predicted. Analysis of profile power changes indicates a decrease in profile power coefficient of 0.00016, corresponding to a loss of 0.12 sq m of equivalent drag area.
Three cracked geometries are studied with the aid of a new finite element model. The procedure employs a variable singularity at the crack tip that tracks changes in the material response during the loading process. Two of the problems are tension-loaded center-crack panels and the other is a three-point bend specimen. Results usually agree with other numerical and analytical analyses, except the finding that J is path dependent as a substantial plastic zone develops. Credible J values are obtained near the crack tip and J shows a significant increase as the radius of J path increases over two orders of magnitude. Incremental and deformation theories are identical provided the stresses exhibit proportionality found in the far field stresses but not near the tip.
For the determination of fracture toughness especially with brittle materials, a short bar specimen with rectangular cross section and chevron notch can be used. As the crack propagates from the tip of the triangular notch, the load increases to a maximum then decreases. To obtain the relation between the fracture toughness and maximum load, calculations of Srawley and Gross for specimens with a straight-through crack were applied to the specimens with chevron notches. For the specimens with a straight-through crack, an analytical expression was obtained. This expression was used for the calculation of the fracture toughness versus maximum load relation under the assumption that the change of the compliance with crack length for the specimen with a chevron notch is the same as for a specimen with a straight-through crack.
Simple modification to bootstrap ramp generator gives more linear output over longer sweep times. New circuit adds just two resistors, one of which is adjustable. Modification cancels nonlinearities due to variations in load on charging capacitor and due to changes in charging current as the voltage across capacitor increases.
Partial and complete emission band reversals have been observed in the infrared emission spectra from portions of operating sliding contacts. An elementary analysis has been carried out to show that partial reversals are due to temperature gradients in the fluid film - the film acts both as a radiation-emitter and absorber, and that total reversals - an emission spectrum appears as an absorption spectrum are likely to be due to a continuum source, such as hot solid asperities. The total energy radiated under the latter conditions exceeds that under the others. A decrease in gap width with increased load was accompanied by a dramatic spectral change in the case of 5P4E polyphenyl ether, which is indicative of molecular alignment.
A bearing/shaft model of the SSME LOX turbopump was developed using the SHABERTH bearing/shaft math modeling computer code. A previously developed bearing/shaft thermal model of the SSME LOX turbopump turbine and bearing was used in conjunction with SHABERTH to evaluate the thermomechanical operating characteristics of the LOX turbopump end bearings. Results show that for the two unmounted diametrical clearances evaluated (4.0 mils and 6.3 mils), the inboard pump end bearing supports about 81% of the isolator load for the small clearance and 77% of the isolator load for the larger clearance. Bearing clearance changes due to thermal effects were 40% for the 4.0 mil diametrical clearance case and 19% for the 6.3 mil clearance case evaluated. The thermal analysis included evaluation of bearing temperatures for a subcooled case and a saturated case. Results indicate that no drastic temperature change occurred between the two cases. Since the rolling element and race surfaces of the subcooled case were at temperatures sufficiently high enough to be vapor blanketed, exceeding saturation temperature at the bearing inlet did not increase surface temperatures greatly.
The nature of the solar wind flow near comets is examined analytically in this paper. In particular, typical values for the stagnation pressure and magnetic barrier strength are estimated, taking into account magnetic field line tension and change-exchange cooling of the mass-loaded solar wind. A knowledge of the strength of the magnetic barrier is required in order to determine the location of the ionopause surface which separates the contaminated solar wind plasma from the outflowing plasma of the cometary ionosphere.
The present paper is concerned with control problems which arise in connection with the establishment and maintenance of space stations. Some of the arising problems are related to great changes in mass and an intensive shock load accompanying Shuttle docking. Such problems can be solved by making use of a robust adaptive control system. Space station configurations developed by NASA and the corresponding mass properties are discussed along with dynamic models for space stations, aspects of problem formulation and control architecture, adaptive control algorithms, a performance analysis, and practical considerations. Attention is given to adaptive regulator control with initial transient, adaptive control during Shuttle docking, and cases involving Shuttle hard docking with model switching and disturbance modeling.
The project is extending an existing finite element tire model to calculate the energy dissipation in a free-rolling aircraft tire and temperature buildup in the tire carcass. The model will provide a means of calculating the influence of tire design on the distribution of tire temperature. Current focus is on energy loss measurements of aircraft tire material. The feasibility of taking test specimens directly from the tire carcass for measurements of viscoelastic properties was demonstrated. The interaction of temperature and frequency effects on material loss properties was studied. The tire model was extended to calculate the cyclic energy change in a tire during rolling under load. Input data representing the 40 by 14 aircraft tire whose material loss properties were measured are being used.
This paper describes two methods, the maximum distortion energy (MDE) and the principle of independent action (PIA), developed for the analysis of the reliability of a single continuous composite lamina. It is shown that, for the typical laminated plate structure, the individual lamina reliabilities can be combined in order to produce the upper and the lower bounds of reliability for the laminate, similar in nature to the bounds on properties produced from variational elastic methods. These limits were derived for both the interactive and the model failure considerations. Analytical expressions were also derived for the sensitivity of the reliability limits with respect to changes in the Weibull parameters and in loading conditions.
The feasibility of changing the bolt shape from circular to elliptical in order to increase the joint strength was investigated. An analytical method using a cosine series to represent the bearing stress was derived, and a boundary collocation method was used to determine the unknown coefficients of this cosine series. Stresses at the hole edge predicted by the analytical method agreed very well with finite element solutions. Failure analyses of joints in two different laminates were performed, and each laminate exhibited a different joint failure mode. Results demonstrate that the joint strength of both laminates can be improved substantially by changing the bolt shape to elliptical. The joint that failed in a bearing mode showed a greater strength increase compared to the joint that failed in a shearing mode.
A numerical analysis of forebody tangential slot blowing as a means of generating side force and yawing moment is conducted using an aircraft geometry. The Reynolds-averaged, thin-layer, Navier-Stokes equations are solved using a partially flux-split, approximately-factored algorithm. An algebraic turbulence model is used to determine the turbulent eddy viscosity values. Solutions are obtained using both patched and overset grid systems. In the patched grid model, and actuator plane is used to introduce jet variables into the flow field. The overset grid model is used to model the physical slot geometry and facilitate modeling of the full aircraft configuration. A slot optimization study indicates that a short slot located close to the nose of the aircraft provided the most side force and yawing moment per unit blowing coefficient. Comparison of computed surface pressure with that obtained in full-scale wind tunnel tests produce good agreement, indicating the numerical method and grid system used in the study are valid. Full aircraft computations resolve the changes in vortex burst point due to blowing. A time-accurate full-aircraft solution shows the effect of blowing on the changes in the frequency of the aerodynamic loads over the vertical tails. A study of the effects of freestream Mach number and various jet parameters indicates blowing remains effective through the transonic Mach range. An investigation of the force onset time lag associated with forebody blowing shows the lag to be minimal. The knowledge obtained in this study may be applied to the design of a forebody tangential slot blowing system for use on flight aircraft.
Concept of tailored precone rotor (TPR) provides for changes in precone deflection in helicopter rotor blade when such changes needed for enhancement of stability and loads. Involves use of device described in "Structurally-Tailorable, Nonlinear Snap-Through Spring," (LAR-13729). Satifies requirements in both rotor states in tailored, passive manner. Also applicable to complex blades of high-speed fans or turbines.
The concept of a yield surface is central to the mathematical formulation of a classical plasticity theory. However, at elevated temperatures, material response can be highly time-dependent, which is beyond the realm of classical plasticity. Viscoplastic theories have been developed for just such conditions. In viscoplastic theories, the flow law is given in terms of inelastic strain rate rather than the inelastic strain increment used in time-independent plasticity. Thus, surfaces of constant inelastic strain rate or flow surfaces are to viscoplastic theories what yield surfaces are to classical plasticity. The purpose of the work reported herein was to validate experimental procedures for determining flow surfaces at elevated temperatures. Since experimental procedures for determining yield surfaces in axial/torsional stress space are well established, they were employed -- except inelastic strain rates were used rather than total inelastic strains. In yield-surface determinations, the use of small-offset definitions of yield minimizes the change of material state and allows multiple loadings to be applied to a single specimen. The key to the experiments reported here was precise, decoupled measurement of axial and torsional strain. With this requirement in mind, the performance of a high-temperature multi-axial extensometer was evaluated by comparing its results with strain gauge results at room temperature. Both the extensometer and strain gauges gave nearly identical yield surfaces (both initial and subsequent) for type 316 stainless steel (316 SS). The extensometer also successfully determined flow surfaces for 316 SS at 650 C. Furthermore, to judge the applicability of the technique for composite materials, yield surfaces were determined for unidirectional tungsten/Kanthal (Fe-Cr-Al).
Atmospheric aerosol particles, both natural and anthropogenic, are important to the earth's radiative balance. They scatter the incoming solar radiation and modify the shortwave reflective properties of clouds by acting as Cloud Condensation Nuclei (CCN). Although it has been recognized that aerosols exert a net cooling influence on climate (Twomey et al. 1984), this effect has received much less attention than the radiative forcings due to clouds and greenhouse gases. The radiative forcing due to aerosols is comparable in magnitude to current anthropogenic greenhouse gas forcing but opposite in sign (Houghton et al. 1990). Atmospheric aerosol particles generated from biomass burning, dust storms and forest fires are important regional climatic variables. A recent study by Penner et al. (1992) proposed that smoke particles from biomass burning may have a significant impact on the global radiation balance. They estimate that about 114 Tg of smoke is produced per year in the tropics through biomass burning. The direct and indirect effects of smoke aerosol due to biomass burning could add up globally to a cooling effect as large as 2 W/sq m. Ackerman and Chung (1992) used model calculations and the Earth Radiation Budget Experiment (ERBE) data to show that in comparison to clear days, the heavy dust loading over the Saudi Arabian peninsula can change the Top of the Atmosphere (TOA) clear sky shortwave and longwave radiant exitance by 40-90 W/sq m and 5-20 W/sq m, respectively. Large particle concentrations produced from these types of events often are found with optical thicknesses greater than one. These aerosol particles are transported across considerable distances from the source (Fraser et al. 1984). and they could perturb the radiative balance significantly. In this study, the regional radiative effects of aerosols produced from biomass burning, dust storms and forest fires are examined using the Advanced Very High Resolution Radiometer (AVHRR) Local Area Coverage (LAC) data and the instantaneous scanner ERBE data from the NOAA-9 and NOAA-10 satellites.