Search NASA⌕ Search

SEARCH · Search NASA

Results for “mass diffusivity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69

Impact of nonaqueous phase liquid (NAPL) source zone architecture on mass removal mechanisms in strongly layered heterogeneous porous media during soil vapor extraction

An existing multiphase flow simulator was modified in order to determine the effects of four mechanisms on NAPL mass removal in a strongly layered heterogeneous vadose zone during soil vapor extraction (SVE): a) NAPL flow, b) diffusion and dispersion from low permeability zones, c) slow desorption from sediment grains, and d) rate-limited dissolution of trapped NAPL. The impact of water and NAPL saturation distribution, NAPL type (i.e., free, residual, or trapped) distribution, and spatial heterogeneity of the permeability field on these mechanisms were evaluated. Two different initial source zone architectures (one with and one without trapped NAPL) were considered and these architectures were used to evaluate seven different SVE scenarios. For all runs, slow diffusion from low permeability zones that gas flow bypassed was a dominant factor for diminished SVE effectiveness at later times. This effect was more significant at high water saturation due to the decrease of gas-phase relative permeability. Transverse dispersion contributed to fast NAPL mass removal from the low permeability layer in both source zone architectures, but longitudinal dispersion did not affect overall mass removal time. Both slow desorption from sediment grains and rate-limited mass transfer from trapped NAPL only marginally affected removal times. However, mass transfer from trapped NAPL did affect mass removal at late time, as well as the NAPL distribution. NAPL flow from low to high permeability zones contributed to faster mass removal from the low permeability layer, and this effect increased when water infiltration was eliminated. These simulations indicate that if trapped NAPL exists in heterogeneous porous media, mass transfer can be improved by delivering gas directly to zones with trapped NAPL and by lowering the water content, which increases the gas relative permeability and changes trapped NAPL to free NAPL.

54 ENVIRONMENTAL SCIENCES↗

Growth of AlGaN/GaN heterojunction field effect transistors on semi-insulating GaN using an AlGaN interlayer

Semi-insulating (SI) GaN layers were grown on 4H-SiC substrates by inserting an AlGaN layer between the AlN buffer and the GaN layer. Secondary ion mass spectroscopy measurements showed that the AlGaN layer prevented Si from diffusing from the substrate into the GaN layer. X-ray diffraction and atomic force microscopy analyses showed that an optimized AlGaN interlayer does not degrade the crystal quality or surface morphology of the SI GaN. The room temperature mobility of an AlGaN/GaN heterostructure using this SI GaN was 2200 cm{sup 2}/V s. High electron mobility transistors (HEMTs) with 0.65 {mu}m long gates were also fabricated on these SI GaN buffers. A power density of 19.0 W/mm with a power added efficiency of 48% was demonstrated at 10 GHz at a drain bias of 78 V. These HEMTs also exhibited sharp pinch off, low leakage, and negligible dispersion.

36 MATERIALS SCIENCE↗

INFRARED SPECTRAL MAPPING OF SUPERNOVA REMNANTS. I. N63A AND ITS ENVIRONMENT

We present Spitzer Space Telescope spectra of the supernova remnant (SNR) N63A and its native H II region N63 in the Large Magellanic Cloud. We measure nebular fine-structure lines, H{sub 2} lines, and polycyclic aromatic hydrocarbons (PAHs). The lines contribute half of the flux in the Spitzer 24 {mu}m image of N63A shocked lobes, but only {<=}10% elsewhere. The mid-IR flux is largely due to thermal continuum emission from dust in and around N63A plasma. Electron densities are low everywhere; the differences in mid-IR line ratios separate N63A plasma and its high-excitation surroundings from N63A low-excitation optical lobes. We compare the observed line fluxes and ratios within N63A's shocked lobes and plasma with the predictions from models for moderate and fast shocks to constrain pre-shock densities and shock velocities. N63A's photoionized lobe contains a warm photodissociation region in pressure equilibrium with optically ionized gas. We apply a physical dust model to our spectra supplemented by MIPS photometry. We derive the intensity of radiation heating the dust, the mass fraction due to PAHs, and the masses of dust within our sampled regions and of cooler grains in the diffuse interstellar medium. N63A's shocked lobes and plasma contain {approx}0.07 M{sub Sun} of hot grains, comparable to amounts in other SNRs. Within N63A there is {approx}0.7 M{sub Sun} of warm grains exposed to {>=}100 times the intensity of the local interstellar radiation field. Within the regions, 92% of the total dust mass resides in cool grains emitting {<=}27% of their mid-IR luminosity.

79 ASTRONOMY AND ASTROPHYSICS↗

Nuclear Archaeology for Gaseous Diffusion Enrichment Plants

Gaseous diffusion was historically the most widely used technology for military production of highly enriched uranium. Since June 2013, all gaseous diffusion enrichment plants worldwide are permanently shut down. The experience with decommissioning some of these plants has shown that they contain large amounts of uranium particles deposited in the cascade equipment. This article evaluates the potential of using uranium particle deposition to understand and reconstruct the operating histories of gaseous diffusion enrichment plants. First, a squared-off cascade enrichment model is derived to estimate the enrichment capacity of a reference plant. Then, using a cross-flow filtration model, the mass of solid uranium particles deposited over time in the tubular separation membranes of the stage diffusers is calculated. Lastly, potential techniques to characterize these uranium deposits and help reconstruct the operating history of the plant are assessed.

07 ISOTOPE AND RADIATION SOURCES↗

The Optical/UV Excess of X-Ray-dim Isolated Neutron Stars. I. Bremsstrahlung Emission from a Strangeon Star Atmosphere

X-ray-dim isolated neutron stars (XDINSs) are characterized by Planckian spectra in X-ray bands, but show optical/ultraviolet (UV) excesses: the factors by which the measured photometry exceeds those extrapolated from X-ray spectra. To solve this problem, a radiative model of bremsstrahlung emission from a plasma atmosphere is established in the regime of a strangeon star. A strangeon star atmosphere could simply be regarded as the upper layer of a normal neutron star. This plasma atmosphere, formed and maintained by the interstellar-medium-accreted matter due to the so-called strangeness barrier, is supposed to be of two temperatures. All seven XDINS spectra could be well fitted by the radiative model, from optical/UV to X-ray bands. The fitted radiation radii of XDINSs are from 7 to 13 km, while the modeled electron temperatures are between 50 and 250 eV, except RX J0806.4–4123, with a radiation radius of ∼3.5 km, indicating that this source could be a low-mass strangeon star candidate. This strangeon star model could further be tested by soft X-ray polarimetry, such as the Lightweight Asymmetry and Magnetism Probe, which is expected to be operational on China’s space station around 2020.

79 ASTRONOMY AND ASTROPHYSICS↗

Diffusive-convective physical vapor transport of PbTe from a Te-rich solid source

Crystal growth of PbTe by physical vapor transport (sublimation) in a closed ampoule is governed by the vapor species in thermal equilibrium with the solid compound. Deviations from stoichiometry in the source material cause diffusion limitation of the transport rate, which can be modified by natural (gravity-driven) convection. Mass-transport experiments have been performed using Te-rich material wherein sublimation rates have been measured in order to study the effects of natural convection in diffusion-limited vapor transport. Linear velocities for both crystal growth and evaporation (back sublimation) have been measured for transport in the direction of gravity, horizontally, and opposite to gravity. The experimental results are discussed in terms of both the one-dimensional diffusive-advective model and current, more sophisticated theory which includes natural convection. There is some evidence that convection effects from radial temperature gradients and solutal density gradients have been observed.

Zoutendyk, J.↗

Higher-order compositional modeling of three-phase flow in 3D fractured porous media based on cross-flow equilibrium

Numerical simulation of multiphase compositional flow in fractured porous media, when all the species can transfer between the phases, is a real challenge. Despite the broad applications in hydrocarbon reservoir engineering and hydrology, a compositional numerical simulator for three-phase flow in fractured media has not appeared in the literature, to the best of our knowledge. In this work, we present a three-phase fully compositional simulator for fractured media, based on higher-order finite element methods. To achieve computational efficiency, we invoke the cross-flow equilibrium (CFE) concept between discrete fractures and a small neighborhood in the matrix blocks. We adopt the mixed hybrid finite element (MHFE) method to approximate convective Darcy fluxes and the pressure equation. This approach is the most natural choice for flow in fractured media. The mass balance equations are discretized by the discontinuous Galerkin (DG) method, which is perhaps the most efficient approach to capture physical discontinuities in phase properties at the matrix-fracture interfaces and at phase boundaries. In this work, we account for gravity and Fickian diffusion. The modeling of capillary effects is discussed in a separate paper. We present the mathematical framework, using the implicit-pressure-explicit-composition (IMPEC) scheme, which facilitates rigorous thermodynamic stability analyses and the computation of phase behavior effects to account for transfer of species between the phases. A deceptively simple CFL condition is implemented to improve numerical stability and accuracy. We provide six numerical examples at both small and larger scales and in two and three dimensions, to demonstrate powerful features of the formulation.

97 MATHEMATICS AND COMPUTING↗

Distortion of Magnetic Fields in a Starless Core: Near-infrared Polarimetry of FeSt 1–457

Magnetic fields are believed to play an important role in controlling the stability and contraction of the dense condensations of gas and dust that lead to the formation of stars and planetary systems. In the present study, the magnetic field of FeSt 1–457, a cold starless molecular cloud core, was mapped on the basis of the polarized near-infrared light from 185 background stars after being dichroically absorbed by dust aligned with the magnetic field in the core. A distinct “hourglass-shaped” magnetic field was identified in the region of the core, and was interpreted as the first evidence of a magnetic field structure distorted by mass condensation in a starless core. The steep curvature of the magnetic field lines obtained in the present study indicates that the distortion was mainly created during the formation phase of the dense core. The derived mass-to-magnetic flux ratio indicates that the core is in a magnetically supercritical state. However, the stability of the core can be considered to be in a nearly critical state if the additional contributions from the thermal and turbulent support are included. Further diffusion of the magnetic field and/or turbulent dissipation would cause the onset of the dynamical collapse of the core. The geometrical relationship between the direction of the magnetic field lines and the elongation of the core was found to be in good agreement with theoretical predictions for the formation of Sun-like stars under the influence of a magnetic field.

79 ASTRONOMY AND ASTROPHYSICS↗

Quantum diffusion during inflation and primordial black holes

We calculate the full probability density function (PDF) of inflationary curvature perturbations, even in the presence of large quantum backreaction. Making use of the stochastic-δ N formalism, two complementary methods are developed, one based on solving an ordinary differential equation for the characteristic function of the PDF, and the other based on solving a heat equation for the PDF directly. In the classical limit where quantum diffusion is small, we develop an expansion scheme that not only recovers the standard Gaussian PDF at leading order, but also allows us to calculate the first non-Gaussian corrections to the usual result. In the opposite limit where quantum diffusion is large, we find that the PDF is given by an elliptic theta function, which is fully characterised by the ratio between the squared width and height (in Planck mass units) of the region where stochastic effects dominate. We then apply these results to the calculation of the mass fraction of primordial black holes from inflation, and show that no more than ∼ 1 e -fold can be spent in regions of the potential dominated by quantum diffusion. We explain how this requirement constrains inflationary potentials with two examples.

79 ASTRONOMY AND ASTROPHYSICS↗

Cu penetration into low-k dielectric during deposition and bias-temperature stress

Cu penetration into low-k dielectrics can cause serious reliability issues in on-chip interconnect systems. Using secondary ion mass spectrometry with both front-side and back-side depth profiling strategies, Cu was found to diffuse into SiCOH low-k dielectric in a Cu/SiCOH/Si capacitor during Cu deposition. After bias-temperature stressing the capacitor at 270 deg. C and 2.5 MV/cm, Cu penetrates further into SiCOH, but its distribution profile is the same as that after the same temperature annealing without electrical bias, suggesting no Cu ion drift. The implication of these findings on the Cu/low-k dielectric time-dependent dielectric breakdown modeling is discussed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Elucidating the Transition of 3D Morphological Evolution of Binary Alloys in Molten Salts with Metal Ion Additives

Molten salts serve as effective high-temperature heat transfer fluids and thermal storage media used in a wide range of energy generation and storage facilities, including concentrated solar power plants, molten salt reactors and high-temperature batteries. However, at the salt–metal interfaces, a complex interplay of charge-transfer reactions involving various metal ions, generated either as fission products or through corrosion of structural materials, takes place. Simultaneously, there is a mass transport of ions or atoms within the molten salt and the parent alloys. The precise physical and chemical mechanisms leading to the diverse morphological changes in these materials remain unclear. Here, to address this knowledge gap, this work employed a combination of synchrotron X-ray nanotomography and electron microscopy to study the morphological and chemical evolution of Ni-20Cr in molten KCl-MgCl 2 , while considering the influence of metal ions (Ni 2+ , Ce 3+ , and Eu 3+ ) and variations in salt composition. Our research suggests that the interplay between interfacial diffusivity and reactivity determines the morphological evolution. The summary of the associated mass transport and reaction processes presented in this work is a step forward toward achieving a fundamental comprehension of the interactions between molten salts and alloys. Overall, the findings offer valuable insights for predicting the diverse chemical and structural alterations experienced by alloys in molten salt environments, thus aiding in the development of protective strategies for future applications involving molten salts.

36 - MATERIALS SCIENCE↗

A Global End-Member Approach to Derive aCDOM(440) from Near-Surface Optical Measurements

This study establishes an optical inversion scheme for deriving the absorption coefficient of colored (or chromophoric, depending on the literature) dissolved organic material (CDOM) at the 440 nm wavelength, which can be applied to global water masses with near-equal efficacy. The approach uses a ratio of diffuse attenuation coefficient spectral end members, i.e., a short and long wavelength pair. The global perspective is established by sampling "extremely" clear water plus a generalized extent in turbidity and optical properties that each span three decades of dynamic range. A unique data set was collected in oceanic, coastal, and inland waters (as shallow as 0.6 m) from the North Pacific Ocean, the Arctic Ocean, Hawaii, Japan, Puerto Rico, and the east and west coasts of the United States. The data were partitioned using subjective categorizations to define a validation quality subset of conservative water masses, i.e., the inflow and outflow of properties constrain the range in the gradient of a constituent, plus 15 subcategories of water masses that were not evolving conservatively. The dependence on subcategories was confirmed with an objective methodology based on cluster analysis techniques. The latter defined five distinct classes with validation quality data present in all classes, but which also decreased in percent composition as a function of increasing class number and optical complexity. Four different algorithms based on different validation quality end members were validated with accuracies of 1.–6.2 %, wherein pairs with the largest spectral span were most accurate. Although algorithm accuracy decreased with the inclusion of more subcategories containing non-conservative water masses, changes to the algorithm fit were small when a preponderance of subcategories were included. The high accuracy for all end-member algorithms was the result of data acquisition and data processing improvements, e.g., increased vertical sampling resolution to less than 1mm and a boundary constraint to mitigate wave focusing effects, respectively. An independent evaluation with a historical database confirmed the consistency of the algorithmic approach and its application to quality assurance, e.g., to flag data outside expected ranges, identify suspect spectra, and objectively determine the in-water extrapolation interval by converging agreement for all applicable end-member algorithms. The legacy data exhibit degraded performance (as 44 % uncertainty) due to a lack of high-quality near-surface observations, especially for clear waters wherein wave-focusing effects are problematic. The novel optical approach allows the in situ estimation of an in-water constituent in keeping with the accuracy obtained in the laboratory.

Stanford B Hooker↗

A horseshoe-shaped ring of diffuse emission detected at 1.4 GHz

We identify a horseshoe-shaped ring (HSR) of diffuse emission in J1407+0453 from the Faint Images of Radio Sky at Twenty-cm (FIRST) survey using the Very Large Array telescope at 1.4 GHz. An optical galaxy, SDSS J140709.01+045302.1, is present near the limb of the HSR of J1407+0453, with a spectroscopic redshift ofz = 0.13360. The total extent of the source, including the diffuse emission of J1407+0453, is 65 arcsec (with a physical extent of 160 kpc), whereas the diameter of the HSR is approximately 10 arcsec (25 kpc). The flux density of the HSR is ∼47 mJy at 1400 MHz, whereas the flux densities of the whole diffuse emission of J1407+0453 at 1400 MHz and 150 MHz are 172 mJy and 763 mJy, respectively. We measure the radio luminosity of HSR J1407+0453 as 1.94 × 10 24 W Hz −1 , with a spectral index,α 150 1400 = −0.67. The black hole mass of J1407+0453 is 5.8 × 10 8 M ⊙ . We compare the HSR of diffuse emission of J1407+0453 with other discovered diffuse circular sources. The possible formation scenarios for J1407+0453 are discussed, so as to understand the nature of the source. We present a spectral index map of source J147+0453 to study the spectral properties of the source.

Astronomy & Astrophysics↗

Experimental Design for Voltage Driven Tracer Incorporation and Diffusion Studies on Oxide Thin Film Electrodes

The effect of an applied overpotential on oxygen isotope incorporation and diffusion in oxide thin film electrodes is investigated by a novel experimental approach. A special electrode geometry leads to in-plane electron flow, perpendicular oxide ion flow and a well-defined laterally varying driving force. This design allows one to obtain a series of tracer depth profiles induced by a range of overpotentials on one and the same thin film. The approach was applied to La 0.8 Sr 0.2 MnO 3 (LSM) thin films deposited by pulsed laser deposition (PLD) on yttria stabilized zirconia (YSZ) single crystals. Tracer depth profiles were measured by secondary ion mass spectrometry (SIMS). These depth profiles include examples of pronounced apparent uphill diffusion that can be explained by considering an interplay of polarization-induced changes in stoichiometry within the LSM grains combined with fast oxygen transport along the grain boundaries.

25 ENERGY STORAGE↗

Experiments and simulation on diffusion and activation of codoped with arsenic and phosphorous germanium

We report arsenic and phosphorus diffusion experiments and activation related phenomena in codoped germanium substrates utilizing conventional thermal annealing. Chemical profiles were obtained by secondary ion mass spectroscopy, sheet resistance was estimated by the Van der Pauw method. Our study covers the temperature range from 600 to 750 deg. C. We accurately described the dopant profiles with a quadratic dependence of the dopants diffusion coefficient on the free electron concentration. In our simulations we considered the dopant pile-up near the surface and dopant loss owing to outdiffusion during the annealing. Although the double donor codoping technique exhibited no advantage over monodoping with P concerning the level of activation and junction depth, it was interesting to observe the different diffusion behavior of the two dopants. Whereas the diffusion of As indicates a retardation under codoping the diffusion of P remains either unaffected or is slightly enhanced by codoping. The activation level of the codoped samples remains lower compared to the respective monodoped samples, except for the highest annealing temperature.

36 MATERIALS SCIENCE↗

Mass dependency of turbulent parameters in stationary glow discharge plasmas

A direct current glow discharge tube is used to determine how mass changes the effects of certain turbulence characteristics in a weakly ionized gas. Helium, neon, argon, and krypton plasmas were created, and an axial magnetic field, varied from 0.0 to 550.0 Gauss, was used to enhance mass dependent properties of turbulence. From the power spectra of light emission variations associated with velocity fluctuations, determination of mass dependency on turbulent characteristic unstable modes, energy associated with turbulence, and the rate at which energy is transferred from scale to scale are measured. The magnetic field strength is found to be too weak to overcome particle diffusion to the walls to affect the turbulence in all four types of plasmas, though mass dependency is still detected. Though the total energy and the rate at which the energy moves between scales are mass invariant, the amplitude of the instability modes that characterize each plasma are dependent on mass.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The use of low-energy SIMS (LE-SIMS) for nanoscale fuel cell material development

Low-energy secondary ion mass spectrometry has been used to investigate the matrix structure and interface attributes of a novel Ce0.85Sm0.15O2/CeO2 multilayer fuel cell material. Nanoscale oxide systems have shown enhanced ionic conductivities when produced to form highly oriented epitaxial structures. The Sm-doped CeO2 material system is of particular interest for fuel cell technology because of its inherently high ionic conductivity at low operating temperatures (600-800 C). For this study, a nanometer-scale Ce0.85Sm0.15O2/CeO2 multilayer was grown by pulsed laser deposition. The sample was annealed at 700 C in an oxygen ambience. High-resolution, low-energy depth profiling using Cs revealed some diffusion of the multilayer structure after annealing, along with a possible volume change for the Sm-doped layers. Changes in layer volume will lead to an increase in the mechanical strain and may cause the material to crack. The findings presented here suggest that the Ce0.85Sm0.15O2/CeO2 multilayer structure in its current form may not possess the level of thermal stability required for use within a fuel cell environment.

30 DIRECT ENERGY CONVERSION↗

Morphology, near-infrared luminosity, and mass of the Galactic bulge from COBE DIRBE observations

Near-infrared images of the Galactic bulge at 1.25, 2.2, 3.5, and 4.9 microns obtained by the Diffuse Infrared Background Experiment (DIRBE) onboard the Cosmic Background Explorer (COBE) satellite are used to characterize its morphology and to determine its infrared luminosity and mass. Earlier analysis of the DIRBE observations (Weiland et al. 1994) provided supporting evidence for the claim made by Blitz & Spergel (1991) that the bulge is bar-shaped with its near end in the first Galactic quadrant. Adopting various triaxial analytical functions to represent the volume emissivity of the source, we confirm the barlike nature of the bulge and show that triaxial Gaussian-type functions provide a better fit to the data than other classes of functions, including an axisymmetric spheroid. The introduction of a `boxy' geometry, such as the one used by Kent, Dame, & Fazio (1991) improves the fit to the data. Our results show that the bar is rotated in the plane with its near side in the first Galactic quadrant creating an angle of 20 deg +/- 10 deg between its major axis and the line of sight to the Galactic center. Typical axis ratios of the bar are (1:0.33 +/- 0.11:0.23 +/- 0.08), resembling the geometry of prolate spheroids. There is no statistically significant evidence for an out-of-plane tilt of the bar at 2.2 microns, and marginal evidence for a tilt of approximately equal 2 deg at 4.9 microns. The introduction of a roll around the intrinsic major axis of the bulge improves the `boxy' appearance of some functions. A simple integration of the observed projected intensity of the bulge gives a bulge luminosity of 1.2 x 10(exp 9), 4.1 x 10(exp 8), 2.3 x 10(exp 8), and 4.3 x 10(exp 7) solar luminosity, respectively, at 1.25, 2.2, 3.5, and 4.9 microns wavelength for a Galactocentric distance of 8.5 kpc. The 2.2 microns luminosity function of the bulge population in the direction of Baade's window yields a bolometric luminosity of L(sub bol) = 5.3 x 10(exp 9) solar luminosity. Stellar evolutionary models relate this luminosity to the number of main-sequence progenitor stars that currently populate the red giant branch. Combined with the recent determination of the main-sequence turnoff mass for the bulge by the Hubble Space Telescope (Holtzman et al. 1993) we derive a photometrically determined bulge mass of approximately equal to 1.3 x 10(exp 10) solar mass for a Salpeter initial mass function extended down to 0.1 solar mass.

Dwek, E.↗