SEARCH · Search NASA
Results for “microstructural engineering”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Plasticity and fracture behavior of Inconel 625 manufactured by laser powder bed fusion: Comparison between as-built and stress relieved conditions
In this work, the influence of stress relief on the plasticity and fracture behavior of Inconel 625 fabricated through laser powder bed fusion additive manufacturing (AM) was investigated. The as-built versus stress relieved microstructures were compared, showing similar grain structures but the presence of ~10 vol % δ phase in the stress relieved condition, and no δ phase in the as-built condition. Mechanical tests under plane strain tension were performed on the stress relieved samples, and an anisotropic plasticity model was calibrated and validated using finite element simulations. Uniaxial and notched tension tests were performed on both as-built and stress relieved samples to probe the effect of stress relief on stress state- and direction-dependent fracture behavior. It was found that on average, the fracture strain of the stress relieved samples along the build direction was 30% higher than that along the perpendicular build direction in the stress state range studied, and the stress relief heat treatment resulted in a 45% decrease in fracture strain. The fracture strain in stress relieved samples was more strongly dependent on stress state than in as-built samples.
Study of growth twins produced through heat treatment of fine-grained magnesium
This study investigated the microstructural features of magnesium after the fine-grained magnesium sample was heat treated at 400 °C for 2 h. Both fine-grained and heat-treated magnesium samples were observed using the electron backscatter diffraction technique in scanning electron microscopy. The results show that the grains were substantially coarsened, the local strain and the local misorientation was significantly reduced, and a large number of twins were observed in the heat-treated magnesium sample. The misorientation angle analysis determined that the twins were oriented about 86.3° away from the orientation of their corresponding matrices, and the twins were the variants of $\{1 0 \bar{1} 2\}$ tensile twins. The relative orientation analysis also identified that the fast growth directions of the twins were closely along the $<2 \bar{1} \bar{1} 0>$ or $<1 0 \bar{1} 0>$ directions in the basal plane. The twins can merge or impinge onto each other. Most boundaries between the twins have the misorientation angle of about 7.4°.
Harnessing catalytic pumps for directional delivery of microparticles in microchambers
The directed transport of microparticles in microfluidic devices is vital for efficient bioassays and fabrication of complex microstructures. There remains, but, a need for methods to propel and steer microscopic cargo that do not require modifying these particles. By using theory and experiments, we show that catalytic surface reactions can be used to deliver microparticle cargo to specified regions in microchambers. Here reagents diffuse from a gel reservoir and react with the catalyst-coated surface. Fluid density gradients due to the spatially varying reagent concentration induce a convective flow, which carries the suspended particles until the reagents are consumed. Consequently, the cargo is deposited around a specific position on the surface. The velocity and final peak location of the cargo can be tuned independently. And by increasing the local particle concentration, highly sensitive assays can be performed efficiently and rapidly. Moreover, the process can be repeated by introducing fresh reagent into the microchamber.
Understanding Microstructural Effects on Dynamic Performance Towards the Development of Shock Metamaterials
With the recent advances in additive manufacturing (AM), long-range periodic lattice assemblies are being developed for vibration and shock mitigation components in aerospace and military applications with unique geometric and topological structures. There has been extensive work in understanding the static properties associated with varying topology of these lattice architectures, but there is almost no understanding of microstructural affects in such structures under high-strain rate dynamic loading conditions. Here we report the shock behavior of lattices with varying intrinsic grain structures achieved by post process annealing. High resolution 316L stainless steel lattices were 3D printed by a laser-powder bed fusion machine and characterized by computed tomography. Subsequent annealing resulted in stress-relieved and recrystallized lattices. Overall the lattices had strong cubic texture aligning with the x-, y- and z-directions of the build with a preference outside the build direction (z). The recrystallized sample had more equiaxed polygonal grains and a layer of BCC ferrite at the surface of the structure approximately 1 grain thick. Upon dynamic compression the as-deposited lattice showed steady compaction behavior while the heat-treated lattices exhibit negative velocity behavior indicative of failure. We attribute this to the stiffer BCC ferrite in the annealed lattices becoming damaged and fragmenting during compression.
Topological Defect Mediated Helical Phase Reorientation by Uniaxial Stress
Strain engineering enables precise, energy-efficient control of nanoscale magnetism. However, unlike well-studied strain-dislocation interactions in mechanical deformation, the spatial evolution of strain-induced spin rearrangement remains poorly understood. Using Lorentz transmission electron microscopy, we manipulate and observe helical domain reorientation under quantitatively applied uniaxial tensile stress. Our findings reveal striking similarity to plastic deformation in metals, where the critical stress for propagation vector ( Q ) reorientation depends on its angle with the stress direction. Magnetic defects mediate reorientation via “break-and-reconnect” or “dislocation gliding–annihilation” processes. Simulations confirm that strain-induced anisotropic Dzyaloshinskii-Moriya interaction may play a key role. These insights advance strain-driven magnetism and offer a promising route for energy-efficient magnetic nanophase control in next-generation information technology. Published by the American Physical Society 2025
Mitigating Corrosion in Mg Sheet in Conjunction with a Sheet-Joining Method that Satisfies Structural Requirements within Sub-assemblies
This work was undertaken as a LightMAT project funded by the DOE-Vehicles Technology Office. The goal of this work was to develop corrosion protection strategies that simultaneously mitigate corrosion and achieve Class-A surface finish for Mg components in automotive applications. While automotive metals such as steel and aluminum are protected against corrosion through a variety of coating schemes/packages, the efficacy of these existing coating schemes for Mg and Mg- joints is not clear and needs to be determined. Therefore, five commercially available coating schemes and two joining techniques (riveting and Arplas resistance spot welding) were evaluated. The corresponding individual Mg sheet coupons or Mg/Mg joint test coupons were provided by Magna that were then corrosion tested at PNNL using ASTM B117 procedure. The microstructures and mechanical properties of the coupons were analyzed to determine the effectiveness of the joining and corrosion mitigation strategies. Of the coating schemes evaluated, Henkel Bonderite MgC 2.0 pre-treatment + E-coat showed the best corrosion protection and surface finish for individual Mg coupons and Arplas resistance spot welded coupons. However, the strength of Mg/Mg welded joint was reduced after corrosion testing due to some corrosion at the weld nugget. Mg/Mg rivet joints in conjunction with Chemetall oxisilan pre-treatment + polyurethane coating showed good corrosion resistance and some discoloration on the surface finish. Coating schemes comprising pre-treatment with Alodine 5200 + E-coat or Bonderite 1455 + polyurethane coating, in conjunction with Al rivet joints, showed significant corrosion and extensive discoloration of the surface. We anticipate that the results from this work will provide useful guidance to the automotive industry in selecting the appropriate combinations of corrosion protection coatings and joining techniques to fabricate light-weight Mg-based automotive components.
Magnesium Technology 2020
Magnesium and its alloys are being investigated widely for applications that require extraordinarily high strength-to-weight ratio, vibration damping, electromagnetic shielding, reduction in carbon footprint, sustainability improvements, and low toxicity. In the past decade or so, this drive has led to increased adoption of magnesium and its alloys in everyday products and it is no longer regarded as an esoteric material. The overarching goal of its widespread adoption and replacement of conventional materials such as steel and aluminum alloys has been restricted because of the cost of the material, limited sources of primary material, alloying constraints, high chemical reactivity, and challenges associated with its plasticity. Researchers, scientists, engineers, and economists from industry, government agencies and laboratories, and academic institutions alike are actively developing roadmaps for next-generation products and addressing these challenges as quickly as possible through unique and innovative methods. The TMS Magnesium Committee has been actively involved in providing a platform to these entities for disseminating the latest information, developments, and cutting-edge research and development, and showcasing the latest research and development trends related to magnesium and its alloys through the Magnesium Technology Symposium, which takes place every year at the TMS Annual Meeting. This proceedings volume retains the essence of this longstanding tradition. The twenty-first volume in the series, Magnesium Technology 2020, is the proceedings of the Magnesium Technology Symposium held during the 149th TMS Annual Meeting & Exhibition in San Diego, CA, February 23–27, 2020. The volume captures commentaries and papers from 15 different countries. The papers have been categorized systematically based on topics pertaining to magnesium production, casting and solidification, thermomechanical processing, deformation mechanisms, modeling, corrosion, and applications. The symposium began with keynote sessions that featured several distinguished invited speakers from government organizations and academia, who provided their perspectives on the state of the art, goals, and opportunities in magnesium alloy research and development. Dr. Carlos Tomé from Los Alamos National Laboratory, U.S. Department of Energy, discussed 3D characterization of mechanical twins across grain boundaries. This was followed by a talk on hierarchically structured ultrafine-grained magnesium alloys by Dr. Rajiv Mishra from the University of North Texas, USA, who presented an example of using friction stir additive manufacturing for implementing such microstructures at a component level. Dr. Mark Horstemeyer from Liberty University, USA, presented an overview of fatigue modeling to capture the corrosion-fatigue behavior of magnesium alloys. The final talk in this session was presented by Dr. Bin Jiang from Chongqing University, China, who presented a novel extrusion approach for achieving high-strength magnesium alloy plates.
Thermodynamic properties of Gd-Bi alloys determined by emf measurements in LiCl-KCl-GdCl 3 electrolyte
Thermodynamic properties of binary Gd-Bi alloys (mole fraction, x Gd = 0.02–0.35) were determined using electromotive force (emf) measurements in molten LiCl-KCl-GdCl 3 electrolyte in complement with structural, microstructural, and thermal characterization. X-ray diffractometry (XRD) and scanning electron microscopy (SEM) identified the phase constituents of Gd-Bi alloys (x Gd = 0.02–0.35) as Bi matrix and GdBi compound. According to differential scanning calorimetry (DSC) measurements up to 1250 K, a eutectic transition [L = Bi + GdBi] was observed at 543 K but the reported peritectic transition [L + GdBi = GdBi 2 ] was not detected, suggesting the absence of the GdBi 2 compound. Based on structural, microstructural, and thermal characterization of Gd-Bi alloys (x Gd = 0.02–0.35), the GdBi 2 compound was not detected, and its thermodynamic stability is questionable. The emf of Gd-Bi alloy (x Gd = 0.16) at 700–1048 K relative to Gd(s) was measured by electrodepositing pure Gd metal at 25 K increments. Further, the emf values of Gd-Bi alloys were determined via coulometric titration of Gd into liquid Bi using a two-phase [L + GdBi] alloy as a reference electrode at 773–973 K. The solubility of Gd in liquid Bi was also estimated to be 0.50 mol% (773 K), 0.99 mol% (873 K), and 2.21 mol% (973 K) and the excess partial molar Gibbs energy (Δ$\mathrm{\bar{G}^{ex}_{Gd}}$) of liquid Gd-Bi alloys was as low as 65 kJ mol –1 , indicating strong chemical interactions between Gd and Bi.
Embedding Sensors in 3D Printed Metal Structures
The Transformational Challenge Reactor (TCR) program is leveraging recent advances in modeling and simulation, materials, and additive manufacturing (AM) technologies to design a modern nuclear reactor. Some of the main TCR technologies include in situ monitoring and the integration of sensors during the manufacturing of quality-significant nuclear reactor components. This report describes the general procedure and process optimization for embedding sensors within generic stainless steel 316 (SS316) components using laser powder bed fusion (LPBF). A more detailed, quality-significant test plan and supporting procedures are available upon request (ORNL/TM-2021/2127). LPBF involves the use of a scanning laser to selectively melt regions of a powder bed, additively building a part layer by layer. This report describes the LPBF processing technique and discusses the effects of LPBF processing parameters on the success of the sensor embedding process. Experiments used machined cavities in the form of channels in an SS316 base for the sensors to lay in while material is additively built over the top, thereby embedding them in an SS316 matrix. A preliminary investigation involved using empty SS316 sheaths as surrogates to explore the effects of various LPBF processing parameters and the dimensional requirements of the machined channels. Microstructural investigations showed that a smaller channel width/depth combination closer to the sensor’s diameter was best for the embedding process. After the desired parameters were selected, Type-K thermocouples were embedded and evaluated post-embedding using nondestructive thermal testing, as well as destructive sectioning and microscopy. Post-build characterization showed that the thermocouples were well-bonded to the SS316 matrix and were fully functional after embedding. During thermal testing to temperatures up to 500 °C, the embedded thermocouples read consistently with one another and deviated only slightly from the readings of a nonembedded thermocouple located within the furnace. This slight discrepancy was most likely due to differences in the thermal time constants for a nonembedded thermocouple vs. a thermocouple embedded in a solid SS316 block. The results presented in this report will serve as the foundation for future work that will focus on embedding sensors in relevant TCR reactor components and eventually testing those components under neutron irradiation.
Creep anisotropy modeling and uncertainty quantification of an additively manufactured Ni-based superalloy
The advantages offered by additive manufacturing over traditional processes has driven a great deal of industrial and academic interest in recent years. However, the process is relatively new and requires additional investigation to become sufficiently mature for wide scale industrial adoption. Electron beam melting powder bed fusion is one technology that has shown promise for fabricating high temperature resistant materials such as nickel based superalloys. The resulting microstructures typically exhibit a strong fiber texture in the build direction giving rise to anisotropic time-dependent deformation behavior. In order to accelerate the qualification of these materials for industrial adoption accurate numerical models are needed for simulating their behavior. In this work a crystal plasticity model including non-Schmid effects is presented for capturing creep anisotropy observed in additively manufactured IN738LC. The model is calibrated via a probabilistic framework where model parameters are treated as random variables. An iterative sequential design strategy is utilized to efficiently identify the probability density of the unknown model parameters. As a case study the model is utilized to investigate the behavior of randomly oriented equiaxed grain clusters sometimes observed embedded in the additively manufactured columnar structure. A synthetic realization is simulated and uncertainty is propagated through to the full-field response. Results indicate that these features are the source of significant creep relaxation and strain accumulation which partially explains observed grain boundary decohesion at these locations.
Proposed Material Properties, Allowable Stresses, and Design Curves of Diffusion Bonded Alloy 800H for the ASME Code Section III Division 5
Abstract Increased interest in compact heat exchangers (CHXs) to serve as intermediate heat exchangers of very high temperature reactors resulted in significant research and development on their design, analysis, and construction. Printed circuit heat exchangers are a type of CHXs with high thermal efficiency and compactness achieved through diffusion bonding a stack of etched plates with millimeter scaled channels. The diffusion bonding process changes the microstructural and mechanical properties of the wrought metal plates. The current nonnuclear design code ASME section VIII, division 1 captures the material property change through a “joint efficiency factor.” However, the current nuclear design code ASME section III, division 5 does not address or support the diffusion bonded material properties. Hence, there is a need to develop allowable stresses, isochronous curves, and fatigue life curves for various diffusion bonded alloys. In this study, Alloy 800H material was selected to establish the diffusion bonded material properties under tension, creep, fatigue, and creep-fatigue loads at elevated temperatures in the range 550–760 °C. A set of tests on diffusion bonded Alloy 800H (DB 800H) were performed and the acquired data are used in developing allowable stresses Sy, Su, Sr, Sm, St, Smt, So, isochronous curves and fatigue life curves according to the ASME section III, division 5 requirements. This paper also presents detailed procedures used in developing the ASME code section III division 5 design provisions for diffusion bonded Alloy 800H.
In-situ and ex-situ characterization of ion-irradiated AM materials
Additive manufacturing (AM) has attracted increasing attention in recent years as a new way of making high-quality components for nuclear reactors. While AM materials are compositionally similar to their conventionally produced counterparts, they do possess different microstructures, such as dislocation cells and chemical inhomogeneity, that can lead to different mechanical properties and performance behavior. In this study, the irradiation response of AM materials was investigated. In-situ and ex-situ ion irradiations were performed on AM316L and AM316H stainless steels (SS) at 300 and 600°C. The influence of the dislocation cell structure on the evolution of irradiation-induced dislocation loops was evident at 600ºC, but was much weaker at 300ºC. No voids were observed with the in-situ ion irradiation up to 10 dpa at both temperatures. Post-irradiation energy dispersive spectroscopy showed radiation-induced segregation (RIS) near grain boundaries and the formation of Cr-rich oxides throughout the matrix. The extent of segregation at dislocation cell walls varies with dose. Nanoindentation tests performed on the AM316L SS irradiated at 600ºC showed a complex dose dependence with softening at low doses and hardening at high doses.
A leaf-molded transparent triboelectric nanogenerator for smart multifunctional applications
Transparent, flexible and highly efficient portable power sources are essential components of the next generation electronics and optoelectronic devices. However, complicated technology, expensive cost, environmental pollution and low-efficient output have limited its development. Herein, based on periodic contact/separation between human skin and the microstructured polydimethylsiloxane (PDMS) film, we demonstrate a transparent flexible triboelectric nanogenerator (TENG) through a relatively simple, low-cost, environmental-friendly and high-efficient method. For the first time, the natural leaves with rich surface textures were introduced to make microstructures on PDMS films as effective friction surface in the TENG. Furthermore, long silver nanowires (200 µm in length at least) through novel synthesis were assembled as high-performance electrode, resulting in the entirely flexible and transparent TENG. Owing to the unique design, the transparent flexible TENG was eventually obtained with an enhanced output (Voc=56 V; Isc=3.1 μA) and remarkable transparency (88%). Owing to compelling features of the TENG, a self-powered user-interactive wearable system was successfully established by integrating a flexible electrochromic device (ECD). The remarkable color-tunable ability via mechanical control of our system, highly inspired by chameleons, is potentially useful in military camouflage, monitoring human activity visually, as well as replacing performance of face change in Sichuan Opera. Therefore, this research is a substantial advancement toward the construction of transparent nanogenerator and its multifunctional applications in energy conversation, wearable electronics, healthcare, culture experience, and even environmental protection.
AOI [3]: Smart Refractory Sensor Systems for Wireless Monitoring of Temperature, Health, and Degradation of Slagging Gasifiers
The objective of the work was to develop refractory “smart bricks”, which would contain embedded temperature, strain/stress, and spallation sensors throughout the volume of highchromia (-Cr 2 O 3 ) refractory brick. The proposed work included work to interconnect the sensors to the reactor exterior, where the sensor signals may be processed by low-power electronics and transmitted wirelessly to a central processing hub. The data processing and wireless transmitter hardware was specifically designed to be isolated (with low power consumption) and to be adaptable to future implementation of energy-harvesting strategies for extended life. Finally, the collected data was incorporated into a model to estimate refractory degradation, a technique that could help monitor the health of the refractory in real-time. The long-term goal of this program was to demonstrate high-temperature, wireless sensor arrays for in situ three-dimensional (3-D) refractory monitoring or mapping for slagging gasification systems. The research was in collaboration with HarbisonWalker International (HWI) Technology Center in West Mifflin, PA. HWI is a leading developer and manufacturer of ceramic refractory products for high-temperature applications. The work completed focused on the following areas: 1) Investigation of the chemical stability, microstructural evolution, grain growth kinetics, degree of homogeneity (quantitative image analysis), and electrical properties of refractory oxide-silicide composites at temperatures between 750-1450ºC; 2) Fabrication of silicide-alumina composite and oxide thermocouples and thermistor preforms and the development of techniques to embed them into high-chromia refractory bricks to form “smart bricks”; 3) Utilization of commercial off-the-shelf discrete components to prototype circuits for interfacing between smart brick sensors and the wireless sensor network. The prototypes were then used to design an integrated circuit for thermistor, thermocouple, and capacitive-based smart brick sensor interfacing; 4) Interfacing of the smart bricks with embedded sensors with wireless motes thus yielding a complete signal chain. This end-to-end data collection system was tested on a furnace heated to 1350°C; 5) Development of a slag penetration model and a nonlinear unknown input filter for the data from the embedded sensors for estimating temperature and extent of slag penetration.
Metallurgical Analysis and Forward Modeling of Weld Distortion in SMR Containment Vessels
This work aimed to apply Sandia’s expertise in metallurgy and modeling to enable the use of hybrid laser arc welding for building nuclear reactor containment structures, via a collaboration with Holtec International. Experimental observations were coupled with finite element analysis to resolve microstructure development, mechanical properties, distortion, and residual stress in welds relevant to the production of the Holtec SMR-160. High residual stresses were observed in welds that were not subjected to preheat. Meanwhile, the microstructure of the welds generally exhibited a narrow heat affected zone relative to conventional arc welds. FEA appeared to be effective in simulating the thermal/mechanical conditions that occur during hybrid laser arc welding of simplified and instrumented test welds. Subsequently, FEA was used to perform sensitivity analyses for various weld geometries that would be prohibitively costly to assess with physical experiments. Insights from the study were used to inform Holtec’s welding process, and successful production welds were performed in 2025.
Design and characterization of hierarchical aluminosilicate composite materials for Cs entrapment: Adsorption efficiency tied to microstructure
The growing quantity of nuclear waste and the serious threats to the environment challenge researchers to innovate and target new waste form technologies. In the past decades, considerable efforts have been devoted to developing highly selective sorbents followed by safe disposal with the assurance of chemical stability and robust retention performance. Zeolite-containing geopolymers are regarded as a possible 2-in-1 material able to both capture and sequester elements such as Cs in bed fixed column application perspective. Here, these composites show promise for combining extraction properties of zeolite powder due to its crystalline structure (high capacity and selective adsorption), with the tunable microstructure and the shaping feasibility of the geopolymer binder. For the development of materials devoted to Cs immobilization, porous zeolite/geopolymer composites were prepared by dispersing NaY zeolite particles in a geopolymer binder. The influence of the structural properties of such composites on their ability to entrap a large amount of Cs by an ionic exchange process was notably studied. Composites' compositions, porosities, morphologies and crystallinity were analyzed by scanning electron microscopy coupled with energy dispersive x-ray spectroscopy (SEM-EDX), x-ray diffraction analysis (XRD) and nitrogen adsorption/desorption studies. Experimental Cs sorption in batch mode was used to follow the ionic exchange phenomenon in these materials. Along with 5 wt% amount of zeolite in geopolymer improves the Cs adsorption performance offering multiple new adsorption sites. Additionally, the geopolymer mesopores are beneficial facilitating the access of Cs and its role as a binder is advantageous to tailor granular hierarchical structure for safer industrial application.
Instabilities and phase transitions in architected metamaterials: a gradient-enhanced continuum approach
Architected metamaterials such as foams and lattices exhibit a wide range of properties governed by microstructural instabilities and emerging phase transitions. Their macroscopic response–including energy dissipation during impact, large recoverable deformations, morphing between configurations, and auxetic behavior–remains difficult to capture with conventional continuum models, which often rely on discrete approaches that limit scalability. In this work, we propose a nonlocal continuum formulation that captures both stable and unstable responses of elastic architected metamaterials. The framework extends anisotropic hyperelasticity by introducing nonlocal variables and internal length scales reflective of microstructural features. Local polyconvex free-energy models are systematically augmented with two families of non-(poly)convex energies, enabling both metastable and bistable responses. Implementation in a finite element framework enables solution using a hybrid monolithic–staggered strategy. Simulations capture densification fronts, forward and reverse transitions, hysteresis loops, imperfection sensitivity, and globally coordinated auxetic modes. Overall, this framework provides a robust foundation for accelerated modeling of instability-driven phenomena in architected metamaterials, while enabling extensions to anisotropic, dissipative, and active systems as well as integration with data-driven and machine learning approaches.