Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface layering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69

Study of quasi-two- and three-dimensional ordered porous structures by means of small-angle X-ray scattering in the grazing incidence geometry

The structure of surface layers of thin metal inverse opals has been studied first by the grazing-incidence small-angle X-ray scattering technique. Contributions of the form factor and structure factor to the small-angle diffraction pattern have been separated using a numerical model of the scattering process. The complementary use of the small-angle X-ray scattering and grazing-incidence small-angle X-ray scattering techniques has provided independent information about the bulk and surface properties of the samples and allowed a type of defect in the investigated structures to be determined. The measurement results have been verified by atomic force microscopy.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Optimization of concentrator photovoltaic solar cell performance through photonic engineering

The goal of this program was to incorporate two new and innovative design concepts into the design and production of CPV cells that have near zero added cost, yet significantly increase the operational efficiency of CPV modules. The program focused developing luminescent coupling effects and radiative cooling layers to increase efficiency and suppress CPV module power losses due to spectral variations and heating. The major results of the program were: 1) The optics of three commercial refractive (Fresnel) concentrators were characterized and prevent application of radiative cooling concepts due to strong mid-IR absorption (4-12µm) required to effectively radiate blackbody radiation from the cells and provide cooling. Investigation of alternative materials for the concentrator lenses produced only undesirable options—materials with reasonable mid-IR transmission for cooling only had about 30-40 visible transmission, thus reducing incident sunlight by >50%. While our investigation was somewhat limited, our work suggests that the only viable concentrator system that can incorporate radiative cooling utilizes reflective optics. 2) With limited ability to test high concentration CPV cells (requires outdoor testing), we acquired both semi-crystalline and crystalline Si cells and tested them in our outdoor facility and demonstrated 4°C cooling using a simple silica layer coating on the cells. 3) Characterizing Si cells in the IR associated with radiative cooling, we observed very significant near-IR absorption that increases the cell operating temperature by a similar amount, 4-5°C. By appropriate surface layer design, one can produce a layer that is highly reflective in the near-IR (1.5-4µm) and highly emissive in the mid-IR (5-15µm), thus reducing cell operational temperature by 10°C and increasing efficiency by ~1% absolute. The radiative cooling effect in c-Si solar cells might be further improved by providing a higher thermal conductive elastomer for securing the cover glass on top of the AR-coating. Since it was never imagined that the front surface would provide any cooling for solar cells, thermal conductivity of this elastomer was never a design consideration, but, improving the conductivity could decrease cell temperature by another 3-4°C. The combined effect could be an ~1.5% absolute increase in cell and module efficiency, a very significant improvement. 4) Developed a numerical model to explore dependence of luminescent coupling efficiency over a broad range of operating conditions. We developed a novel method and facility to experimentally measure the luminescent coupling that can be used to confirm the dependence of luminescent coupling on multi-junction cell design parameters.

14 SOLAR ENERGY↗

Techniques Optimized for Reducing Instabilities in Advanced Nickel-Base Superalloys for Turbine Blades

The High-Speed Research (HSR) Airfoil Alloy program developed fourth-generation single-crystal superalloys with up to an 85 F increase in creep rupture capability over current production airfoil alloys. Recent results have been generated at the NASA Glenn Research Center on these fourth-generation alloys, but in coated form, for subsonic turbine blade applications under NASA's Ultra-Efficient Engine Technology (UEET) Program. One goal for UEET is to optimize the airfoil alloy/thermal barrier coating system for 3100 F turbine inlet temperatures. The state-of-the art turbine blade airfoil system consists of a superalloy single crystal that provides the basic mechanical performance of the airfoil. A thermal barrier coating is used to reduce the temperature of the base superalloy, and a bondcoat is deposited between the base material and the thermal barrier coating. The bondcoat improves the oxidation and corrosion resistance of the base superalloy and improves the spallation resistance of the thermal barrier coating. A commercial platinum aluminide bondcoat was applied to the HSR-developed alloys, and a diffusion zone developed as a result of interaction between the bondcoat and the superalloy. Optimized strength is obtained for superalloys when the refractory element content is high and the limits of microstructural stability are approached or exceeded slightly. For fourthgeneration alloys, instability leads to the formation of topologically close packed (TCP) phases, which form internally in the superalloy, and a secondary reaction zone (SRZ), which forms under the diffusion zone. There was a concern that excessive quantities of either TCP or SRZ might decrease the mechanical properties of the superalloy, with SRZ thought to be particularly detrimental and its formation unpredictable. Thus, an SRZreduction effort was initiated in the NASA UEET Program so that methods developed during the HSR project could be optimized further to reduce or eliminate the SRZ. An SRZ is a three-phase constituent composed of TCP and stringers of gamma phase in a matrix of gamma prime. An incoherent grain boundary separates the SRZ from the gammagamma prime microstructure of the superalloy. The SRZ is believed to form as a result of local chemistry changes in the superalloy due to the application of the diffusion aluminide bondcoat. Locally high surface stresses also appear to promote the formation of the SRZ. Thus, techniques that change the local alloy chemistry or reduce surface stresses have been examined for their effectiveness in reducing SRZ. These SRZ-reduction steps are performed on the test specimen or the turbine blade before the bondcoat is applied. Stressrelief heat treatments developed at NASA Glenn have been demonstrated to reduce significantly the amount of SRZ that develops during subsequent high-temperature exposures. Stress-relief heat treatments reduce surface stresses by recrystallizing a thin surface layer of the superalloy. However, in alloys with very high propensities to form SRZ, stress relief heat treatments alone do not eliminate SRZ entirely. Thus, techniques that modify the local chemistry under the bondcoat have been emphasized and optimized successfully at Glenn. One such technique is carburization, which changes the local chemistry by forming submicron carbides near the surface of the superalloy. Detailed characterizations have demonstrated that the depth and uniform distribution of these carbides are enhanced when a stress relief treatment and an appropriate surface preparation are employed in advance of the carburization treatment. Even in alloys that have the propensity to develop a continuous SRZ layer beneath the diffusion zone, the SRZ has been completely eliminated or reduced to low, manageable levels when this combination of techniques is utilized. Now that the techniques to mitigate SRZ have been established at Glenn, TCP phase formation is being emphasized in ongoing work under the UEET Program. The limitsf stability of the fourth-generation alloys with respect to TCP phase formation are currently being defined along with high-temperature creep rupture properties. In addition, a regression model is being developed at Glenn for the prediction of the presence of TCP phase in the microstructure and SRZ under the diffusion zone. The model is based on a design-of-experiments methodology with emphasis on the potential synergistic effects of alloying elements.

MacKay, Rebecca A.↗

High-Temperature Grafting Silylation for Minimizing Leaching of Acid Functionality from Hydrophobic Mesoporous Silicas Used as Catalysts in the Liquid Phase

Ordered-hexagonal silica materials, such as Mobil crystalline material-41 and Santa Barbara amorphous-15, have important applications in heterogeneous catalysis and biomass conversion due to their chemical stability and mesoporous structure. Low-temperature grafting (LG) is one of the most common functionalization methods used to modify the acidity/basicity or hydrophobicity/hydrophilicity of the surface. However, the materials prepared by this method are prone to leaching of functional groups into the reaction medium. The exact nature of the leaching phenomenon has not been fully addressed in the literature. In this contribution, we have investigated this process at the molecular level by combining well-controlled reaction experiments and several characterization techniques (Fourier transform infrared, 1 H– 29 Si cross-polarization magic-angle spinning NMR, X-ray diffraction, thermogravimetric analysis, and N 2 adsorption–desorption). We have found that leaching is originated by the presence of terminal surface silanols, which render the catalysts susceptible to the attack of water and polar compounds. Hence, instead of simple detaching of functional groups, leaching can be better described as a partial dissolution of the surface layers of the silica, which of course also removes the functional groups during this process. Therefore, an effective strategy to minimize leaching is to reduce the density of free silanols via full functionalization of the surface. Here, we propose a novel silylation method, high-temperature grafting, which allows the grafting process to be conducted at high temperatures (180 °C) under solvent-free conditions. By this method, a more complete silylation of surface silanols can be obtained. Consequently, the samples prepared by this high-temperature grafting method show to be highly stable during acid-catalyzed alkylation reaction, conducted under severe conditions (high temperature and in the presence of polar solvents).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Surface compositional profiles of self-assembled InAs/GaAs quantum rings

The surface composition profiles of self-assembled InAs/GaAs quantum rings (QR) are studied both experimentally and theoretically. By using X-ray Photoemission Electron Microscopy (XPEEM) we obtain a 2D composition mapping of unburied rings, which can be directly related to the QR topography measured by Atomic Force Microscopy (AFM). Top-surface composition mapping allows us to obtain information on structures which cannot be directly accessed with cross-sectional studies since overgrowing the QRs with a thick GaAs film alters both their morphology and composition. The 2D surface maps reveal a non-uniform distribution across the rings with an In richer InGaAs alloy in the central hole regions. Elastic energy calculations via a Valence Force Field (VFF) approach show that, for a given shape of the rings and a fixed total number of Ga and In atoms, an In enrichment of the alloy in the central hole region, together with an In enrichment of the surface layers, leads to a lowering of the total strain energy.

36 MATERIALS SCIENCE↗

Mn incorporation into the GaAs lattice investigated by hard x-ray photoelectron spectroscopy and diffraction

Photoelectron spectroscopy and diffraction have been used to investigate structural changes during the annealing process of Ga{sub 1-x}Mn{sub x}As samples. Hard x-ray radiation helped in observing photoelectron core-level spectra and electron diffraction from the bulk underlying the oxidized surface layer. High electron-energy resolution enabled us to separate the components due to substitutional and interstitial Mn atoms in the intrinsic Mn 2p{sub 3/2} photoemission profile, resulting in two peaks at 638.8 and 639.5 eV binding energy, respectively. The peaks display the known characteristic behavior after annealing, that is, an almost complete reduction of the interstitial component and preservation of the substitutional component. In the photoelectron diffraction, a sensitivity of high-energy polar plots to the incorporation sites of photoemitting atoms into the atomic lattice has been shown. As a consequence, the experimental polar plots from substitutional and interstitial Mn atoms, which are supported theoretically, show characteristic features that provide structural information. From the similarities and differences of the polar plots for Mn and Ga, we have confirmed the assignment of components within the intrinsic part of the photoemission Mn 2p{sub 3/2} signal suggested by photoelectron spectroscopy.

36 MATERIALS SCIENCE↗

Fusion Crust and the Measurement of Surface Ages of Antarctic Ordinary Chondrites

Natural thermoluminescence (TL) reflects radiation exposure and storage temperature. Meteorites generally exhibit thermoluminescence acquired during their long exposure to galactic cosmic rays in space. During atmospheric passage, temperatures are high enough to completely drain the TL, in the first mm of material under the fusion crust. We therefore refer to this surface layer as "fusion crust" although it does include some unmelted material just below the crust. When the meteorite lands on earth this drained layer will begin to build up natural TL once again due to radiation from cosmic rays and internal radionuclides. Cosmic ray annual dose is estimated to be between 0.04 and 0.06 rad/yr on the earth's surface in Antarctica while the internal radionuclides contribute only about 0.01 rad/yr. Therefore the total annual dose received by the meteorite while it is on the surface is between 0.05 and 0.07 rad/yr. If the meteorite is buried deeply in the ice it is effectively shielded from most cosmic rays and thus only internal radioactivity contributes to the annual dose.

Akridge, Jannette M. C.↗

Supertwisted spirals of layered materials enabled by growth on non-Euclidean surfaces

Using curves to make twists The growth of layered materials on flat substrates usually occurs in stacked layers, although defects or a lattice mismatch can induce strains that distort the shape of subsequent layers. However, these effects are usually small and can be uncontrolled. Zhao et al. now demonstrate the possibility of synthesizing multilayers of two-dimensional materials with certain twists between the layers induced by the presence of screw dislocations in combination with curved substrate surfaces. Different twist angles are achieved by varying the amount of nonplanarity and the character (conical or hyperbolic) of the surface. Science , this issue p. 442

Science & Technology - Other Topics↗

Effects of Heat Input on Weld-Bead Geometry, Surface Chemical Composition, Corrosion Behavior and Thermal Properties of Fiber Laser-Welded Nitinol Shape Memory Alloy

Bead-on-plate laser welding was carried out on 1-mm-thick Nitinol sheets at different heat input values. The variations in weld-bead geometry and variations in microstructures across the bead were studied. The effects of heat input on surface layer composition of the welded samples, corrosion properties and phase transformation temperature were examined. From x-ray photoelectron spectroscopy (XPS), it was clear that relative intensity of elemental Ni peak was higher in parent material and the oxidation state of Ti was Ti{sup 4+}. It was further observed from Auger electron spectroscopy (AES) that the Ti to Ni ratio on the top surface of the welded samples was more than 1, and as a result of this the stability of TiO{sub 2} layer was enhanced, which eventually helped to improve the corrosion property of the welded samples. The polarization resistance of the welded samples was increased by more than ten times compared to that of the un-welded samples. From differential scanning calorimetry (DSC), it became evident that phase transformation temperatures got changed due to welding.

36 MATERIALS SCIENCE↗

VERTICAL STRUCTURE OF STATIONARY ACCRETION DISKS WITH A LARGE-SCALE MAGNETIC FIELD

In earlier works we pointed out that the disk's surface layers are non-turbulent and thus highly conducting (or non-diffusive) because the hydrodynamic and/or magnetorotational instabilities are suppressed high in the disk where the magnetic and radiation pressures are larger than the plasma thermal pressure. Here, we calculate the vertical profiles of the stationary accretion flows (with radial and azimuthal components), and the profiles of the large-scale, magnetic field taking into account the turbulent viscosity and diffusivity and the fact that the turbulence vanishes at the surface of the disk. Also, here we require that the radial accretion speed be zero at the disk's surface and we assume that the ratio of the turbulent viscosity to the turbulent magnetic diffusivity is of order unity. Thus, at the disk's surface there are three boundary conditions. As a result, for a fixed dimensionless viscosity {alpha}-value, we find that there is a definite relation between the ratio R of the accretion power going into magnetic disk winds to the viscous power dissipation and the midplane plasma-{beta}, which is the ratio of the plasma to magnetic pressure in the disk. For a specific disk model with R of order unity we find that the critical value required for a stationary solution is {beta}{sub c} Almost-Equal-To 2.4r/({alpha}h), where h is the disk's half thickness. For weaker magnetic fields, {beta} > {beta}{sub c}, we argue that the poloidal field will advect outward while for {beta} < {beta}{sub c} it will advect inward. Alternatively, if the disk wind is negligible (R<<1), there are stationary solutions with {beta} >> {beta}{sub c}.

79 ASTRONOMY AND ASTROPHYSICS↗

Solution processed nickel oxide anodes for organic photovoltaic devices

Nickel oxide thin films have been prepared from a nickel acetylacetonate (Ni(acac)) precursor for use in bulk heterojunction organic photovoltaic devices. The conversion of Ni(acac) to NiO{sub x} has been investigated. Oxygen plasma treatment of the NiO layer after annealing at 400 °C affords solar cell efficiencies of 5.2%. Photoelectron spectroscopy shows that high temperature annealing converts the Ni(acac) to a reduced form of nickel oxide. Additional oxygen plasma treatment further oxidizes the surface layers and deepens the NiO work function from 4.7 eV for the annealed film, to 5.0 eV allowing for efficient hole extraction at the organic interface.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Biological control of surface temperature in the Arabian Sea

In the Arabian Sea, the southwest monsoon promotes seasonal upwelling of deep water, which supplies nutrients to the surface layer and leads to a marked increase in phytoplankton growth. Remotely sensed data on ocean color are used here to show that the resulting distribution of phytoplankton exerts a controlling influence on the seasonal evolution of sea surface temperature. This results in a corresponding modification of ocean-atmosphere heat exchange on regional and seasonal scales. It is shown that this biological mechanism may provide an important regulating influence on ocean-atmosphere interactions.

Sathyendranath, Shubha↗

Chemical State of Surface Oxygen on Carbon and Its Effects on the Capacity of the Carbon Anode in a Lithium-Ion Battery Investigated

In a lithium-ion battery, the lithium-storage capacity of the carbon anode is greatly affected by a surface layer formed during the first half cycle of lithium insertion and release into and out of the carbon anode. The formation of this solid-electrolyte interface, in turn, is affected by the chemistry of the carbon surface. A study at the NASA Glenn Research Center examined the cause-and-effect relations. Information obtained from this research could contribute in designing a high-capacity lithium-ion battery and, therefore, small, powerful spacecraft. In one test, three types of surfaces were examined: (1) a surface with low oxygen content (1.5 at.%) and a high concentration of active sites, (2) a surface with 4.5 at.% -OH or -OC type oxygen, and (3) a surface with 6.5 at.% O=C type oxygen. The samples were made from the same precursor and had similar bulk properties. They were tested under a constant current of 10 mA/g in half cells that used lithium metal as the counter electrode and 0.5 M lithium iodide in 50/50 (vol%) ethylene carbonate and dimethyl carbonate as the electrolyte. For the first cycle of the electrochemical test, the graph describes the voltage of the carbon anode versus the lithium metal as a function of the capacity (amount of lithium insertion or release). From these data, it can be observed that the surface with low oxygen and a high concentration of active sites could result in a high irreversible capacity. Such a high irreversible capacity could be prevented if the active sites were allowed to react with oxygen in air, producing -OH or -OC type oxygen. The O=C type oxygen, on the other hand, could greatly reduce the capacity of lithium intercalation and, therefore, needs to be avoided during battery fabrication.

Hung, Ching-Cheh↗

The Chemistry of Pluto and its Satellites

Pluto's bulk composition and the composition of the surface layers hold clues to the origin and evolution of a number of other Solar System bodies of comparable size in the region beyond Neptune. The July 14, 2015 flyby of the Pluto system with the New Horizons spacecraft afforded the opportunity to corroborate and greatly improve discoveries about the planet and its satellites derived Earth-based studies. It also revealed extraordinary details of the surface and atmosphere of Pluto, as well as the geology and composition of Charon and two smaller satellites. With a mean density of 1.86 g/sq cm, the bulk composition of Pluto is about two-thirds anhydrous solar composition rocky material and one-third volatiles (primarily H2O in liquid and solid states) by mass, the surface is a veneer of ices dominated by N2, with smaller amounts of CH4 and CO, as well as limited exposures of H2O ice (considered to be "bedrock"). N2, CH4, and CO occur as solid solutions at temperature-dependent mutual concentrations, each component being soluble in the others. Frozen C2H6 as a minor component has also been identified. Sublimation and recondensation of N2, CH4, and CO over seasonal (248 y) and Milankovich-type megaseasons (approx. 3 My) result in the redistribution of these ices over time and with latitude control. Solid N2 is found in glaciers originating in higher elevations and flowing at the present time into a basin structure larger than the State of Texas, forming a convecting lens of N2 that overturns on a timescale of order 10 My. The varied colors of Pluto's landscape arise from the energetic processing of the surface ices in processes that break the simple molecules and reassemble complex organic structures consisting of groups of aromatic rings connected by aliphatic chains. When synthesized in the laboratory by UV or electron irradiation of a Pluto mix of ice, this material, called tholin, has colors closely similar to Pluto. The Pluto ice tholin analog contains carboxylic acids, urea, ketones, aldehydes, amines, and some nitriles. The largest satellite, Charon has density 1.70 g/sq cm and it is about 3/5 anhydrous solar composition rock, with the remainder in H2O ice. The surface H2O ice is infused in some way with NH3, probably as a hydrate, distributed nonuniformly, but to some degree related to geological structures. Pluto's atmosphere is N2, CH4, with CO, C2-hydrocarbons, HCN, and other molecules in trace but detectable amounts. The atmosphere supports a complex haze structure with about 20 discrete layers, and suspected clouds. The haze is presumed to be made of aggregates of complex hydrocarbons (tholins) produced by photolysis of the atmospheric gases, and with similar composition to the ice tholins made on the planet's surface. Urea and a suite of carboxylic acids are of interest for prebiotic and biological chemistries.

SOLAR SYSTEMS↗

Properties of insulator interfaces with p-HgCdTe

Heat treatment at 70 C of low carrier concentration p-type HgCdTe samples (p sub o = 8 x 10 exp 14/cm) generates an inverted surface layer. A two day anneal process below 95 C did not affect the Hall coefficient, whereas an almost complete recovery was obtained by annealing at 120 C. While bulk electron mobility, obtained from PEM data, remained high (about 9 x 10 exp 4 sq cm/V s at 77 K), surface mobility is lower by more than an order of magnitude. Surface recombination velocity indicates a continuous improvement with increased temperature, and the activation energy remains equal to the vacancies energy level. The proposed mechanism is that of positive changes in the sulfide migrating towards the interface and generating an image inversion layer.

Schacham, Samuel E.↗

Unravelling structural ambiguities in lithium- and manganese-rich transition metal oxides

Although Li- and Mn-rich transition metal oxides have been extensively studied as high-capacity cathode materials for Li-ion batteries, the crystal structure of these materials in their pristine state is not yet fully understood. Here we apply complementary electron microscopy and spectroscopy techniques at multi-length scale on well-formed Li1.2(Ni0.13Mn0.54Co0.13)O2 crystals with two different morphologies as well as two commercially available materials with similar compositions, and unambiguously describe the structural make-up of these samples. Systematically observing the entire primary particles along multiple zone axes reveals that they are consistently made up of a single phase, save for rare localized defects and a thin surface layer on certain crystallographic facets. Finally and more specifically, we show the bulk of the oxides can be described as an aperiodic crystal consisting of randomly stacked domains that correspond to three variants of monoclinic structure, while the surface is composed of a Co- and/or Ni-rich spinel with antisite defects.

36 MATERIALS SCIENCE↗

Interaction of vacuum ultraviolet light with a low-k organosilicate glass film in the presence of NH{sub 3}

In situ x-ray photoemission spectroscopy (XPS) and ex situ Fourier transform infrared spectroscopy (FTIR) were used to characterize effects on organosilicate films of 147 nm irradiation in the presence of 10{sup -4} Torr NH{sub 3}. XPS and FTIR data indicate Si-O and Si-C bond scission, with nitridation only at Si sites. Photoirradiation causes the surface layer to become enriched in sp{sup 2} carbon. FTIR spectra of silanol formation upon exposure to ambient indicate reactive sites in the bulk have lifetimes of up to six days. XPS data indicate lifetimes of approxminutes for surface states. Nitrogen uptake passivates with longer exposure times, indicating surface densification.

36 MATERIALS SCIENCE↗