SEARCH · Search NASA

Results for “6 GHz”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

All sources NASA NTRS DOE OSTI

NASA NTRS1977

ATS-6 ascending: Near horizon measurements over water at 30 GHz

The return of the ATS 6 satellite to a western longitude during the fall of 1976 presented a unique opportunity to perform low angle of elevation measurements at 30 GHz. For this purpose a receiver using a 1.5 m antenna was set up at Port Aransas, Texas, resulting in a propagation path entirely over water. The 30 GHz beacon was monitored daily for at least one hour from 8 September 1976 to 21 September 1976. During the time the elevation angle changed from 1.5 deg to 17.3 deg, the mean attenuation decreased from 20 dB to 2 dB and the standard deviation from over 6 dB to less than .2 dB. The deep fades at angles below 4 deg show significantly sharper nulls than peaks on a log scale. Spectra of the log amplitude fluctuations vary as the (-8/3) power of the spectral frequency in the limit. A flattening is noticeable at the low frequencies. A precipitation event at 8.5 deg elevation produced a 16 dB fade and significantly increased the variance.

Vogel, W. J.↗

NASA NTRS2014

Results from Two Years of Ka-Band Propagation Characterization at Svalbard, Norway

Over the several years, NASA plans to launch several earth science missions which are expected to achieve data throughputs of 5-40 terabits per day transmitted from low earth orbiting spacecraft to ground stations. The current S-band and X-band frequency allocations in use by NASA, however, are incapable of supporting the data rates required to meet this demand. As such, NASA is in the planning stages to upgrade its existing Near Earth Network (NEN) Polar ground stations to support Ka-band (25.5-27 GHz) operations. Consequently, it becomes imperative that characterization of propagation effects at these NEN sites is conducted to determine expected system performance, particularly at low elevation angles ((is) less than 10 deg) where spacecraft signal acquisition typically occurs. Since May 2011, NASA Glenn Research Center has installed and operated a Ka-band radiometer at the NEN site located in Svalbard, Norway. The Ka-band radiometer monitors the water vapor line, as well as 6 frequencies around 26.5 GHz at multiple elevation angles: 45 deg, 20 deg, and 10 deg. Two year data collection results indicate comparable performance to previously characterized northern latitude sites in the United States, i.e., Fairbanks, Alaska. It is observed that cloud cover at the Svalbard site remains the dominant loss mechanism for Ka-band links, resulting in a margin requirement of 4.1 dB to maintain link availability of 99% at 10 deg elevation.

near earth network↗

NASA NTRS2011

ARCADE 2 Measurement of the Absolute Sky Brightness at 3-90 GHz

The ARCADE 2 instrument has measured the absolute temperature of the sky at frequencies 3, 8, 10, 30, and 90 GHz, uSing an open-aperture cryogenic instrument observing al balloon altitudes with no emissive windows between the beam-forming optics and the sky. An external blackbody calibrator provides an in situ reference. Systematic errors were greatly reduced by using differential radiometers and cooling all critical components to physical temperatures approximating the cosmic microwave background (CMB) temperature. A linear model is used to compare the output of each radiometer to a set of thermometers on the instrument. Small correction. are made for the residual emission from the flight train, balloon, atmosphere, and foreground Galactic emission. The ARCADE 2 data alone show an excess radio rise of 54 +/- 6 mK at 3.3 GHz in addition to a CMB temperature of 2.731 +/- 0.004 K. Combining the ARCADE 2 data with data from the literature shows an excess power-law spectrum of T = 24.1 +/- 2.1 (K)(v/v(sub o)(exp -2.599+/-0.036 from 22 MHz to 10 GHz (v(sub 0) = 310 MHz) in addition to a CMB temperature of 2.725 +/- 0.001 K.

Fixsen, D. J.↗

NASA NTRS1980

Assessment of atmospheric height uncertainties for high precision satellite altimeter missions to monitor ocean currents

The influence of the atmosphere on nadir directed signal associated with satellite altimeters are examined. Frequencies at 6, 13.5, and 35 GHz are selected so as to provide a parameter study. Uncertainties are summarized in both existing and proposed techniques which establish ionospheric and tropospheric height corrections. The error summary thus gives values describing the best you can do in height resolution (as dictated by atmospheric parameters) for a satellite borne altimeter system. The results presented reflect data gleaned from the literature, at large, as well as from the existing body of published literature associated with the Seasat A Altimeter Experiment. Specifically considered are: (1) the effects of precipitation on altimeter signals, (2) range errors due to refractive index variations in both the clear atmosphere (convective and nonconvective) and clouds, and (3) range errors introduced by the ionosphere. A preliminary analysis is pursued establishing the feasibility of incorporating rain rate range gates in a future satellite-borne altimeter system.

Goldhirsh, J.↗

NASA NTRS1986

Ka-band monolithic gain control amplifier

A monolithic gain control amplifier for Ka-band has been developed based on 0.25 micron-gate-length dual-gate FETs fabricated on ion-implanted material. A single-stage monolithic amplifier gives a gain of 6 dB at 31 GHz including fixture losses with a gain control range of over 20 dB. The device and IC design and fabrication are described.

Geddes, J.↗

NASA NTRS2003

The Explorer of Diffuse Galactic Emission (EDGE): Determining the Large-Scale Structure Evolution in the Universe

Measurements of the large-scale anisotropy of the Cosmic Infared Background (CIB) can be used to determine the characteristics of the distribution of galaxies at the largest spatial scales. With this information important tests of galaxy evolution models and primordial structure growth are possible. In this paper, we describe the scientific goals, instrumentation, and operation of EDGE, a mission using an Antarctic Long Duration Balloon (LDB) platform. EDGE will osbserve the anisotropy in the CIB in 8 spectral bands from 270 GHz-1.5 THz with 6 arcminute angular resolution over a region -400 square degrees. EDGE uses a one-meter class off-axis telescope and an array of Frequency Selective Bololeters (FSB) to provide the compact and efficient multi-colar, high sensitivity radiometer required to achieve its scientific objectives.

Silverberg, R. F.↗

NASA NTRS1990

Aircraft microwave observations and simulations of deep convection from 18 to 183 GHz. I - Observations

Aircraft passive microwave observations of deep atmospheric convection at frequencies between 18 and 183 GHz are presented in conjunction with visible and infrared satellite and aircraft observations and ground-based radar observations. Deep convective cores are indicated in the microwave data by negative brightness temperature, T/(B) deviations from the land background (270 K) to extreme T(B) values below 100 K at 37, 92, and 183 GHz and below 200 K at 18 GHz. These T(B) minima, due to scattering by ice held aloft by the intense updrafts, are well correlated with areas of high radar reflectivity. For this land background case, T(B) is inversely correlated with rain rate at all frequencies due to T(B)-ice-rain correlations. Mean Delta-T between vertically polarized and horizontally polarized radiance in precipitation areas is approximately 6 K at both 18 GHz and 37 GHz, indicating nonspherical precipitation-size ice particles with a preferred horizontal orientation. Convective cores not observed in the visible and infrared data are clearly defined in the microwave observations, and borders of convective rain areas are well defined using the high-frequency (90 GHz and greater) microwave observations.

Adler, Robert F.↗

NASA NTRS2002

Bolometric detectors for the Planck surveyor

The High Frequency Instrument on the NASA/ESA Planck Surveyor, scheduled for launch in 2007, will map the entire sky in 6 frequency bands ranging from 100 GHz to 857 GHz to probe Cosmic Microwave Background (CMB) anisotropy and polarization with angular resolution ranging from 9' to 5'. The HFI focal plane will contain 48 silicon nitride micromesh bolometers operating from a 100 mK heat sink. Four detectors in each of the 6 bands will detect unpolarized radiation. An additional 4 pairs of detectors will provide sensitivity to linear polarization of emission at 143, 217 and 353 GHz. We report on the development and characterization of these detectors before delivery to the European HFI consortium.

bolometers millimeter-wave Planck↗

NASA NTRS1979

Estimating tropical cyclone outer surface winds from satellite microwave data

Warm temperature anomalies over tropical cyclones are sensed by the 55.45 GHz channel of the Nimbus 6 Scanning Microwave Spectrometer. Radial brightness temperature gradients are related to radial surface pressure gradients through the hydrostatic and radiative transfer equations. Surface wind speeds outside of the radius of maximum wind are calculated from the pressure gradients and compared with observations.

Kidder, S. Q.↗

NASA NTRS2018

Toward Large Field-Of-View High-Resolution X-Ray Imaging Spectrometers: Microwave Multiplexed Readout of 28 TES Microcalorimeters

We performed small-scale demonstrations at GSFC of high-resolution Xray TES microcalorimeters read out using a microwave SQUID multiplexer. This work is part of our effort to develop detector and readout technologies for future space-based X-ray instruments such as the microcalorimeter spectrometer envisaged for Lynx, a large mission concept under development for the Astro 2020 Decadal Survey. In this paper we describe our experiment, including details of a recently designed, microwave-optimized low-temperature setup that is thermally anchored to the 55mKstage of our laboratory ADR. Using aROACH2 FPGA at room temperature, we read out pixels of a GSFC-built detector array via a NIST-built multiplexer chip with Nb coplanar waveguide resonators coupled to rf-SQUIDs. The resonators are spaced 6 MHz apart (at ∼ 5.9 GHz) and have quality factors of ∼ 15,000. In our initial demonstration, we used flux-ramp modulation frequencies of 125 kHz to read out 5 pixels simultaneously and achieved spectral resolutions of 2.8-3.1 eV FWHM at 5.9 keV. Our subsequent work is ongoing: to-date we have achieved a median spectral resolution of 3.4 eV FWHM at 5.9 keV while reading out 28 pixels simultaneously with flux-ramp frequencies of 160 kHz. We present the measured system-level noise and maximum slew rates and briefly describe our future development work.

Yoon, W.↗

NASA NTRS2019

Determination of the Cosmic Infrared Background from COBE/FIRAS and Planck HFI Observations

New determinations are presented of the cosmic infrared background monopole brightness in thePlanckHFI bands from 100 to 857 GHz. Planck was not designed to measure the monopole component of sky brightness, so cross-correlation of the 2015 HFI maps with COBE/FIRAS data is used to recalibrate the zero level of the HFI maps. For the HFI 545 and 857 GHz maps, the brightness scale is also recalibrated. Correlation of the recalibrated HFI maps with a linear combination of Galactic HI and Hα data is used to separate the Galactic foreground emission and determine the cosmic infrared background brightness in each of the HFI bands. We obtain CIB values of 0.007, ±0.014, 0.010, ±0.019, 0.060, ±0.023, 0.149, ±0.017, 0.371, ±0.018, and 0.576, ±0.034 MJy sr−1at100, 143, 217, 353, 545, and 857 GHz, respectively. The estimated uncertainties for the 353–857 GHz bands are about 3–6 times smaller than those of previous direct CIB determinations at these frequencies. Our results are compared with integrated source brightness results from selected recent submillimeter and millimeter wavelength imaging surveys.

N. Odegard↗

NASA NTRS2017

Toward Large FOV High-Resolution X-Ray Imaging Spectrometer: Microwave Multiplexed Readout of 32 TES Microcalorimeters

We performed a small-scale demonstration at GSFC of high-resolution x-ray TES microcalorimeters read out using a microwave SQUID multiplexer. This work is part of our effort to develop detector and readout technologies for future space based x-ray instruments such as the microcalorimeter spectrometer envisaged for Lynx, a large mission concept under development for the Astro 2020 Decadal Survey. In this paper we describe our experiment, including details of a recently designed, microwave-optimized low-temperature setup that is thermally anchored to the 50 mK stage of our laboratory ADR. Using a ROACH2 FPGA at room temperature, we simultaneously read out 32 pixels of a GSFC-built detector array via a NIST-built multiplexer chip with Nb coplanar waveguide resonators coupled to RF SQUIDs. The resonators are spaced 6 MHz apart (at approx. 5.9 GHz) and have quality factors of approximately 15,000. Using flux-ramp modulation frequencies of 160 kHz we have achieved spectral resolutions of 3 eV FWHM on each pixel at 6 keV. We will present the measured system-level noise and maximum slew rates, and briefly describe the implications for future detector and readout design.

Yoon, Wonsik↗

NASA NTRS2020

Small Aperture Telescopes for the Simons Observatory

The Simons Observatory (SO) is an upcoming cosmic microwave background(CMB) experiment located on Cerro Toco, Chile, that will map the microwave sky in temperature and polarization in six frequency bands spanning 27 to 285 GHz. SO will consist of one 6-meter Large Aperture Telescope (LAT) fielding∼30,000 detectors and an array of three 0.42-meter Small Aperture Telescopes (SATs) fielding an additional 30,000 detectors. This synergy will allow for the extremely sensitive characterization of the CMB over an-gular scales ranging from an arcmin to tens of degrees, enabling a wide range of scientific output. Here we focus on the SATs targeting degree angular scales with successive dichroic instruments observing at Mid-Frequency (MF: 93/145 GHz), Ultra-High-Frequency (UHF:225/285 GHz), and Low-Frequency (LF: 27/39 GHz). The three SATs will be able to map∼10% of the sky to a noise level of∼2 μK-arcmin when combining 93 and 145 GHz. The multiple frequency bands will allow the CMB to be separated from galactic foregrounds (primarily synchrotron and dust), with the primary science goal of characterizing the primordial tensor-to-scalar ratio, r, at a target level ofσ(r)≈0.003.

Small aperature telescope↗

NASA NTRS1991

A cooled 1-2 GHz balanced HEMT amplifier

The design details and measurement results for a cooled 1-GHz-bandwidth L-band HEMT amplifier are presented. The HEMT noise parameters were measured at a physical temperature of 12 K, and a balanced configuration was adopted. This has the advantage of providing a good input match even though the amplifiers in the two arms of the balanced circuit are poorly matched. However, there are disadvantages. The loss of the input hybrid degrades the noise temperature and coupling errors in the hybrids, and differences between the amplifiers reduce the gain and result in a noise contribution from the input load. In the amplifier described, these effects degrade the noise temperature by less than 1 K. The amplifier uses commercially available packaged HEMT devices. At a physical temperature of 12 K the amplifier achieves noise temperatures between 3 and 6 K over the 1-2-GHz band. The associated gain is about 20 dB.

Padin, Stephen↗

NASA NTRS2019

Evaluation of Ultem 1000, 1010, and 9085 for Radome Applications at 24.5 GHz

The UAS in the NAS project Flight Test 6 (FT6) campaign scheduled for FY19Q3 will evaluate the proficiency of a Honeywell DAPA-Lite Radar installed on a Tiger Shark unmanned vehicle to detect the presence of air traffic operating in its vicinity. A 3D printed radome will be manufactured for the front of the Tiger Shark to enclose the radar during FT6 operations. The DAPA-Lite radar operates in the 24.5 GHz frequency band. Material properties of 3D printer filaments are widely available for the mechanical and thermal properties, but limited knowledge exists on the electrical properties for radome applications and no data was found to correspond at the 24.5 Ghz frequency band. To minimize project risk associated with the radome performance, transmissivity and reflectivity measurements were conducted on two candidate 3D printed dielectric material filaments (Ultem 1010 Natural and Ultem 9085 Black) and two thicknesses of a solid laminate (Ultem 1000) material. The 3D printed Ultem coupons were tested shortly after being printed and again 8 months later to examine ageing effects of the open cell structure. This paper presents the transmissivity and reflectivity measurement results collected on the Ultem coupons and concludes the 3D printed 1010 Natural coupon is a suitable candidate filament for radome applications at 24.5 GHz. The design of the structure’s open cell matrix has a significant impact on the material’s surface reflectivity.

Szatkowski, George N.↗

NASA NTRS1991

A cooled 1- to 2-GHz balanced HEMT amplifier

The design details and measurement results for a cooled L-band (1 to 2 GHz) balanced high electron mobility transistor (HEMT) amplifier are presented. The amplifier uses commercially available packaged HEMT devices (Fujitsu FHR02FH). At a physical temperature of 12 K, the amplifier achieves noise temperatures between 3 and 6 K over the 1 to 2 GHz band. The associated gain is approximately 20 dB.

G. G. Ortiz↗

NASA NTRS1992

Hysteresis effects in instantaneous frequency scaling of attenuation on 20 and 30 GHz satellite links

It has been observed with 20/30 GHz satellite beacon measurements that the ratio of 30 GHz to 20 GHz attenuation changes during some fade events. This ratio displays a hysteresis effect. This effect can be explained by a change in the drop size distribution (DSD) during the event. However, it appears only above approximately 6-8 dB of attenuation at 20 GHz. Instantaneous frequency scaling of attenuation is being proposed as part of an algorithm for uplink power control (ULPC) and the dynamic range of such an algorithm must be appropriately limited to avoid the hysteresis.

Sweeney, D. G.↗

NASA NTRS1975

Comparison between reflectivity statistics at heights of 3 and 6 km and rain rate statistics at ground level

An experiment was conducted to study the relations between the empirical distribution functions of reflectivity at specified locations above the surface and the corresponding functions at the surface. A bistatic radar system was used to measure continuously the scattering cross section per unit volume at heights of 3 and 6 km. A frequency of 3.7 GHz was used in the tests. It was found that the distribution functions for reflectivity may significantly change with height at heights below the level of the melting layer.

Crane, R. K.↗