Search NASA⌕ Search

SEARCH · Search NASA

Results for “AIRFOILS - ASPECT RATIO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1961

Aerodynamic Effects of Some Configuration Variables on the Aeroelastic Characteristics of Lifting Surfaces at Mach Numbers from 0.7 to 6.86

Results of flutter tests on some simple all-movable-control-type models are given. One set of models, which had a square planform with double-wedge airfoils with four different values of leading- and trailing-edge radii from 0 to 6 percent chord and airfoil thicknesses of 9, 11, 14, and 20 percent chord, was tested at Mach numbers from 0.7 to 6.86. The bending-to-torsion frequency ratio was about 0.33. The other set of models, which had a tapered planform with single-wedge and double-wedge airfoils with thicknesses of 3, 6, 9, and 12 percent chord, was tested at Mach numbers from 0.7 to 3.98 and a frequency ratio of about 0.42. The tests indicate that, in general, increasing thickness has a destabilizing effect at the higher Mach numbers but is stabilizing at subsonic and transonic Mach numbers. Double-wedge airfoils are more prone to flutter than single-wedge airfoils at comparable stiffness levels. Increasing airfoil bluntness has a stabilizing effect on the flutter boundary at supersonic speeds but has a negligible effect at subsonic speeds. However, increasing bluntness may also lead to divergence at supersonic speeds. Results of calculations using second-order piston-theory aerodynamics in conjunction with a coupled-mode analysis and an uncoupled-mode analysis are compared with the experimental results for the sharp-edge airfoils at supersonic speeds. The uncoupled-mode analysis more accurately predicted the flutter characteristics of the tapered-planform models, whereas the coupled-mode analysis was somewhat better for the square-planform models. For both the uncoupled- and coupled-mode analyses, agreement with the experimental results improved with increasing Mach number. In general, both methods of analysis gave unconservative results with respect to the experimental flutter boundaries.

Hanson, Perry W.↗
NASA NTRS1986

Aerodynamic data banks for Clark-Y, NACA 4-digit and NACA 16-series airfoil families

With the renewed interest in propellers as means of obtaining thrust and fuel efficiency in addition to the increased utilization of the computer, a significant amount of progress was made in the development of theoretical models to predict the performance of propeller systems. Inherent in the majority of the theoretical performance models to date is the need for airfoil data banks which provide lift, drag, and moment coefficient values as a function of Mach number, angle-of-attack, maximum thickness to chord ratio, and Reynolds number. Realizing the need for such data, a study was initiated to provide airfoil data banks for three commonly used airfoil families in propeller design and analysis. The families chosen consisted of the Clark-Y, NACA 16 series, and NACA 4 digit series airfoils. The various component of each computer code, the source of the data used to create the airfoil data bank, the limitations of each data bank, program listing, and a sample case with its associated input-output are described. Each airfoil data bank computer code was written to be used on the Amdahl Computer system, which is IBM compatible and uses Fortran.

Korkan, K. D.↗
NASA NTRS1959

Analysis and Evaluation of Supersonic Underwing Heat Addition

The linearized theory for heat addition under a wing has been developed to optimize wing geometry, heat addition, and angle of attack. The optimum wing has all of the thickness on the underside of the airfoil, with maximum-thickness point well downstream, has a moderate thickness ratio, and operates at an optimum angle of attack. The heat addition is confined between the fore Mach waves from under the trailing surface of the wing. By linearized theory, a wing at optimum angle of attack may have a range efficiency about twice that of a wing at zero angle of attack. More rigorous calculations using the method of characteristics for particular flow models were made for heating under a flat-plate wing and for several wings with thickness, both with heat additions concentrated near the wing. The more rigorous calculations yield in practical cases efficiencies about half those estimated by linear theory. An analysis indicates that distributing the heat addition between the fore waves from the undertrailing portion of the wing is a way of improving the performance, and further calculations appear desirable. A comparison of the conventional ramjet-plus wing with underwing heat addition when the heat addition is concentrated near the wing shows the ramjet to be superior on a range basis up to Mach number of about B. The heat distribution under the wing and the assumed ramjet and airframe performance may have a marked effect on this conclusion. Underwing heat addition can be useful in providing high-altitude maneuver capability at high flight Mach numbers for an airplane powered by conventional ramjets during cruise.

wings↗
NASA NTRS1974

Two stage low noise advanced technology fan. 1: Aerodynamic, structural, and acoustic design

A two-stage fan was designed to reduce noise 20 db below current requirements. The first-stage rotor has a design tip speed of 365.8 m/sec and a hub/tip ratio of 0.4. The fan was designed to deliver a pressure ratio of 1.9 with an adiabatic efficiency of 85.3 percent at a specific inlet corrected flow of 209.2kg/sec/sq m. Noise reduction devices include acoustically treated casing walls, a flowpath exit acoustic splitter, a translating centerbody sonic inlet device, widely spaced blade rows, and the proper ratio of blades and vanes. Multiple-circular-arc rotor airfoils, resettable stators, split outer casings, and capability to go to close blade-row spacing are also included.

Messenger, H. E.↗
NASA NTRS1995

Lift-Enhancing Tabs on Multielement Airfoils

The use of flat-plate tabs (similar to Gurney flaps) to enhance the lift of multielement airfoils is extended here by placing them on the pressure side and near the trailing edge of the main element rather than just on the furthest downstream wing element. The tabs studied range in height from 0.125 to 1.25% of the airfoil reference chord. In practice, such tabs would be retracted when the high-lift system is stowed. The effectiveness of the concept was demonstrated experimentally and computationally on a two-dimensional NACA 63(sub 2)-215 Mod B airfoil with a single-slotted, 30%-chord flap. Both the experiments and computations showed that the tabs significantly increase the lift at a given angle of attack and the maximum lift coefficient of the airfoil. The computational results showed that the increased lift was a result of additional turning of the flow by the tab that reduced or eliminated now separation on the flap. The best configuration tested, a 0.5%-chord tab placed 0.5% chord upstream of the trailing edge of the main element, increased the maximum lift coefficient of the airfoil by 12% and the maximum lift-to-drag ratio by 40%.

Ross, James C.↗
NASA NTRS1989

Design optimization of axisymmetric bodies in nonuniform transonic flow

An inviscid transonic code capable of designing an axisymmetric body in a uniform or nonuniform flow was developed. The design was achieved by direct optimiation by coupling an analysis code with an optimizer. Design examples were provided for axisymmetric bodies with fineness ratios of 8.33 and 5 at different Mach numbers. It was shown that by reducing the nose radius and increasing the afterbody thickness of initial shapes obtained from symmetric NACA four-digit airfoil contours, wave drag could be reduced by 29 percent for a body of fineness ratio 8.33 in a nonuniform transonic flow of M = 0.98 to 0.995. The reduction was 41 percent for a body of fineness ratio 5 in a uniform transonic flow of M = 0.925 and 65 percent for the same body but in a nonuniform transonic flow of M = 0.90 to 0.95.

Lan, C. Edward↗
NASA NTRS2015

Tests of Full-Scale Helicopter Rotors at High Advancing Tip Mach Numbers and Advance Ratios

As a continuation of the studies of reference 1, three full-scale helicopter rotors have been tested in the Ames Research Center 40- by SO-foot wind tunnel. All three of them were two-bladed, teetering rotors. One of the rotors incorporated the NACA 0012 airfoil section over the entire length of the blade. This rotor was tested at advance ratios up to 1.05. Both of the other rotors were tapered in thickness and incorporated leading-edge camber over the outer 20 percent of the blade radius. The larger of these rotors was tested at advancing tip Mach numbers up to 1.02. Data were obtained for a wide range of lift and propulsive force, and are presented without discussion.

High Advancing Tip Mach Numbers↗
NASA NTRS1989

An evaluation of three experimental processes for two-dimensional transonic tests

The aerodynamic measurements in conventional wind tunnels usually suffer from the interference effects of the sting supporting the model and the test section walls. These effects are particularly severe in the transonic regime. Sting interference effects can be overcome through the Magnetic Suspension technique. Wall effects can be alleviated by: testing airfoils in conventional, ventilated tunnels at relatively small model to tunnel size ratios; treatment of the tunnel wall boundary layers; or by utilization of the Adaptive Wall Test Section (AWTS) concept. The operating capabilities and results from two of the foremost two-dimensional, transonic, AWTS facilities in existence are assessed. These facilities are the NASA 0.3-Meter Transonic Cryogenic Tunnel and the ONERA T-2 facility located in Toulouse, France. In addition, the results derived from the well known conventional facility, the NAE 5 ft x 5 ft Canadian wind tunnel will be assessed. CAST10/D0A2 Airfoil results will be used in all of the evaluations.

Zuppardi, Gennaro↗
NASA NTRS1959

The Problem of Obtaining High Lift-Drag Ratios at Supersonic Speeds

The importance of the lift to drag ratio is well known to all aircraft designers since it gives, to a great extent, the aerodynamic efficiency of the airplane. Aerodynamic efficiency, however, is only one component of the grand compromise that a completed airplane represents. At subsonic speeds, lift-drag ratios of well over 200 have been measured in wind tunnels on airfoil sections; but few powered aircraft have attained (L/D) value of 20. It is invariably true that the requirements of stability and control, structure, and flight operation all contribute to reducing the design (L/D) (sub max)) considerably below those exotic values which can be predicted from unrestricted aerodynamic theory. If, however, a certain range or operating efficiency is required, there is most certainly a minimum (L/D) (sub max)) value for which the goals are just attainable. If we examine the range equation we see that range is proportional to the lift-drag ratio, the thermopropulsive efficiency, and the logarithm of the initial to final weight ratio. The appearance of the lift-drag ratio as a linear factor in the range equation indicates that every attempt should be made to increase (L/D) (sub max)); however, the search for higher (L/D)max may lead to strange and unorthodox configurations. Most frequently, such configurations are ruled out by the adverse effects of their geometry on the weight ratios. In the present paper, we will deal with the maximum lift-drag ratio problem for conventional configurations having a wing and a body in close proximity to each other. No attempt will be made to select a particular configuration as being the best. However, the promising direction to go from the aerodynamic view will be stressed with the understanding that the other factors may outweight the aerodynamics

Brown, Clinton E.↗
NASA NTRS1975

How big is a windmill - Glauert revisited

The obvious similarities to propellers and helicopter rotors suggest that helicopter technology might be used to improve wind generator performance, perhaps including development of a windmill airfoil. In a back-to-basics approach, this paper reviews the analyses of Glauert to determine basic size-power relations. The energy method of Wheatley developed for helicopter/auto-gyro performance prediction is then incorporated into the basic theory. Equations and charts are presented showing ratios of power output to the ideal power capability as functions of mean blade lift and drag coefficients, solidity and rotor tip speed ratio. It is found there is little possibility for improved performance by using improved airfoils. The basic assumptions of the Glauert theory are reviewed and means are suggested for achieving the basic power capability indicated by momentum theory.

Mccloud, J. L., III↗
NASA NTRS1994

Optimization of Adaptive Intraply Hybrid Fiber Composites with Reliability Considerations

The reliability with bounded distribution parameters (mean, standard deviation) was maximized and the reliability-based cost was minimized for adaptive intra-ply hybrid fiber composites by using a probabilistic method. The probabilistic method accounts for all naturally occurring uncertainties including those in constituent material properties, fabrication variables, structure geometry, and control-related parameters. Probabilistic sensitivity factors were computed and used in the optimization procedures. For actuated change in the angle of attack of an airfoil-like composite shell structure with an adaptive torque plate, the reliability was maximized to 0.9999 probability, with constraints on the mean and standard deviation of the actuation material volume ratio (percentage of actuation composite material in a ply) and the actuation strain coefficient. The reliability-based cost was minimized for an airfoil-like composite shell structure with an adaptive skin and a mean actuation material volume ratio as the design parameter. At a O.9-mean actuation material volume ratio, the minimum cost was obtained.

Shiao, Michael C.↗
NASA NTRS1950

The gas kinetics of very high flight speeds

The aerodynamic forces on bodies of arbitrary shape were investigated under conditions such that the mean free path of the air molecule is greater than the dimensions of the body. Air pressures and friction forces were calculated from gas kinetic theory for surfaces facing both toward and away from the air stream at any angle. Air forces for an atmosphere of definite composition (molecular hydrogen) were calculated as a function of the flight velocity. The results indicate that the friction stresses between the air and the body surface are of the same magnitude as the dynamic pressure and as the air pressures normal to the surface. The application of the general method to the specific cases such as thin airfoils and projectiles leads to high drag coefficients and poor glide ratios even for the theoretically best wing sections.

AIR FLOW VELOCITY - MOLECULAR ENERGIES↗
NASA NTRS1972

Surface temperature effect on subsonic stall.

Results of an analytical and experimental study of boundary layer flow over an aerodynamic surface rejecting heat to a cool environment. This occurs following reentry of a Space Shuttle vehicle. Analytical studies revealed that a surface to freestream temperature ratio, greater than unity tended to destabilize the boundary layer, hastening transition and separation. Therefore, heat transfer accentuated the effect of an adverse pressure gradient. Wind tunnel tests of a 0012-64 NACA airfoil showed that the stall angle was significantly reduced while drag tended to increase for freestream temperature ratios up to 2.2.

Macha, J. M.↗
NASA NTRS1988

Design of low Reynolds number airfoils. I

The low Reynolds number airfoils designated ASM-LRN-003 and -007 have been designed for high section L/D ratios using Drela's (1985) design-and-analysis code; close to 70-percent laminar flow is maintained on the upper surfaces, and 100-percent on the lower, at coefficients of lift of 1.0-1.3, assuming optimum laminar separation and transition control on the upper surface by means of suitable turbulators. If peak performance is critical, airfoils of this type with an undercut front lower surface and a correspondingly sharper leading edge may be resorted to.

Pfenninger, W.↗
NASA NTRS1978

Bounds on thickness and loading noise of rotating blades and the favorable effect of blade sweep on noise reduction

The maxima of amplitudes of thickness and loading noise harmonics are established when the radial distribution of blade chord, thickness ratio, and lift coefficient is specified. It is first shown that only airfoils with thickness distribution and chordwise loading distributions which are symmetric with respect to midchord need be considered for finding the absolute maxima of thickness and loading noise. The resulting chordwise thickness and load distributions for these maximum noise conditions require infinite slope at some points along the chord but otherwise are uniform. It is shown that sweeping the blades reduces the thickness and loading noise, but there is no optimum sweep which generates the lowest noise.

Farassat, F.↗
NASA NTRS1978

A parametric experimental study of the interference effects and the boundary-condition coefficient of slotted wind-tunnel walls

An experimental study of slotted upper and lower walls in a two-dimensional transonic wind tunnel with solid sidewalls is reported. Results are presented for several slot spacings and slot openness ratios. The experimental data are pressure measurements which were made on an airfoil model and on a sidewall near one of the slotted walls. The slotted-wall boundary-condition coefficient, which relates the pressure and streamline curvature near the wall, is determined from the wall pressure measurements. The measured wall-induced interference is correlated with the experimental values for the boundary-condition coefficient. This correlation is compared with theory.

Everhart, J. L.↗
NASA NTRS1978

A parametric experimental study of the slotted-wall boundary condition

An experimental study of slotted upper and lower walls in a two dimensional transonic wind tunnel with solid sidewalls is reported. Results are presented for several slot spacings and slot openness ratios. The experimental data were pressure measurements which were made on an airfoil model and on a sidewall near one of the slotted walls. The slotted-wall boundary condition coefficient, which related the pressure and streamline curvature near the wall, was determined from the wall pressure measurements. The measured wall-induced interference was correlated with the experimental values for the boundary condition coefficient. This correlation was compared with theory.

Everhart, J. L.↗
NASA NTRS1931

Tests of six symmetrical airfoils in the variable density wind tunnel

This paper is the first of a series covering an investigation of a family of airfoils all formed from a basic profile. It gives in preliminary form the results of six symmetrical airfoils, differing only in maximum thickness. The maximum thickness-to-chord ratios are 0.06, 0.09, 0.12, 0.15, 0.18, and 0.21.

Jacobs, Eastman N↗