Search NASA⌕ Search

SEARCH · Search NASA

Results for “AIRFOILS - ASPECT RATIO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

Lift-Enhancing Tabs on Multielement Airfoils

The use of flat-plate tabs (similar to Gurney flaps) to enhance the lift of multielement airfoils is extended here by placing them on the pressure side and near the trailing edge of the main element rather than just on the furthest downstream wing element. The tabs studied range in height from 0.125 to 1.25% of the airfoil reference chord. In practice, such tabs would be retracted when the high-lift system is stowed. The effectiveness of the concept was demonstrated experimentally and computationally on a two-dimensional NACA 63(sub 2)-215 Mod B airfoil with a single-slotted, 30%-chord flap. Both the experiments and computations showed that the tabs significantly increase the lift at a given angle of attack and the maximum lift coefficient of the airfoil. The computational results showed that the increased lift was a result of additional turning of the flow by the tab that reduced or eliminated now separation on the flap. The best configuration tested, a 0.5%-chord tab placed 0.5% chord upstream of the trailing edge of the main element, increased the maximum lift coefficient of the airfoil by 12% and the maximum lift-to-drag ratio by 40%.

Ross, James C.↗
NASA NTRS1989

Design optimization of axisymmetric bodies in nonuniform transonic flow

An inviscid transonic code capable of designing an axisymmetric body in a uniform or nonuniform flow was developed. The design was achieved by direct optimiation by coupling an analysis code with an optimizer. Design examples were provided for axisymmetric bodies with fineness ratios of 8.33 and 5 at different Mach numbers. It was shown that by reducing the nose radius and increasing the afterbody thickness of initial shapes obtained from symmetric NACA four-digit airfoil contours, wave drag could be reduced by 29 percent for a body of fineness ratio 8.33 in a nonuniform transonic flow of M = 0.98 to 0.995. The reduction was 41 percent for a body of fineness ratio 5 in a uniform transonic flow of M = 0.925 and 65 percent for the same body but in a nonuniform transonic flow of M = 0.90 to 0.95.

Lan, C. Edward↗
NASA NTRS2015

Tests of Full-Scale Helicopter Rotors at High Advancing Tip Mach Numbers and Advance Ratios

As a continuation of the studies of reference 1, three full-scale helicopter rotors have been tested in the Ames Research Center 40- by SO-foot wind tunnel. All three of them were two-bladed, teetering rotors. One of the rotors incorporated the NACA 0012 airfoil section over the entire length of the blade. This rotor was tested at advance ratios up to 1.05. Both of the other rotors were tapered in thickness and incorporated leading-edge camber over the outer 20 percent of the blade radius. The larger of these rotors was tested at advancing tip Mach numbers up to 1.02. Data were obtained for a wide range of lift and propulsive force, and are presented without discussion.

High Advancing Tip Mach Numbers↗
NASA NTRS1989

An evaluation of three experimental processes for two-dimensional transonic tests

The aerodynamic measurements in conventional wind tunnels usually suffer from the interference effects of the sting supporting the model and the test section walls. These effects are particularly severe in the transonic regime. Sting interference effects can be overcome through the Magnetic Suspension technique. Wall effects can be alleviated by: testing airfoils in conventional, ventilated tunnels at relatively small model to tunnel size ratios; treatment of the tunnel wall boundary layers; or by utilization of the Adaptive Wall Test Section (AWTS) concept. The operating capabilities and results from two of the foremost two-dimensional, transonic, AWTS facilities in existence are assessed. These facilities are the NASA 0.3-Meter Transonic Cryogenic Tunnel and the ONERA T-2 facility located in Toulouse, France. In addition, the results derived from the well known conventional facility, the NAE 5 ft x 5 ft Canadian wind tunnel will be assessed. CAST10/D0A2 Airfoil results will be used in all of the evaluations.

Zuppardi, Gennaro↗
NASA NTRS1959

The Problem of Obtaining High Lift-Drag Ratios at Supersonic Speeds

The importance of the lift to drag ratio is well known to all aircraft designers since it gives, to a great extent, the aerodynamic efficiency of the airplane. Aerodynamic efficiency, however, is only one component of the grand compromise that a completed airplane represents. At subsonic speeds, lift-drag ratios of well over 200 have been measured in wind tunnels on airfoil sections; but few powered aircraft have attained (L/D) value of 20. It is invariably true that the requirements of stability and control, structure, and flight operation all contribute to reducing the design (L/D) (sub max)) considerably below those exotic values which can be predicted from unrestricted aerodynamic theory. If, however, a certain range or operating efficiency is required, there is most certainly a minimum (L/D) (sub max)) value for which the goals are just attainable. If we examine the range equation we see that range is proportional to the lift-drag ratio, the thermopropulsive efficiency, and the logarithm of the initial to final weight ratio. The appearance of the lift-drag ratio as a linear factor in the range equation indicates that every attempt should be made to increase (L/D) (sub max)); however, the search for higher (L/D)max may lead to strange and unorthodox configurations. Most frequently, such configurations are ruled out by the adverse effects of their geometry on the weight ratios. In the present paper, we will deal with the maximum lift-drag ratio problem for conventional configurations having a wing and a body in close proximity to each other. No attempt will be made to select a particular configuration as being the best. However, the promising direction to go from the aerodynamic view will be stressed with the understanding that the other factors may outweight the aerodynamics

Brown, Clinton E.↗
NASA NTRS1975

How big is a windmill - Glauert revisited

The obvious similarities to propellers and helicopter rotors suggest that helicopter technology might be used to improve wind generator performance, perhaps including development of a windmill airfoil. In a back-to-basics approach, this paper reviews the analyses of Glauert to determine basic size-power relations. The energy method of Wheatley developed for helicopter/auto-gyro performance prediction is then incorporated into the basic theory. Equations and charts are presented showing ratios of power output to the ideal power capability as functions of mean blade lift and drag coefficients, solidity and rotor tip speed ratio. It is found there is little possibility for improved performance by using improved airfoils. The basic assumptions of the Glauert theory are reviewed and means are suggested for achieving the basic power capability indicated by momentum theory.

Mccloud, J. L., III↗
NASA NTRS1994

Optimization of Adaptive Intraply Hybrid Fiber Composites with Reliability Considerations

The reliability with bounded distribution parameters (mean, standard deviation) was maximized and the reliability-based cost was minimized for adaptive intra-ply hybrid fiber composites by using a probabilistic method. The probabilistic method accounts for all naturally occurring uncertainties including those in constituent material properties, fabrication variables, structure geometry, and control-related parameters. Probabilistic sensitivity factors were computed and used in the optimization procedures. For actuated change in the angle of attack of an airfoil-like composite shell structure with an adaptive torque plate, the reliability was maximized to 0.9999 probability, with constraints on the mean and standard deviation of the actuation material volume ratio (percentage of actuation composite material in a ply) and the actuation strain coefficient. The reliability-based cost was minimized for an airfoil-like composite shell structure with an adaptive skin and a mean actuation material volume ratio as the design parameter. At a O.9-mean actuation material volume ratio, the minimum cost was obtained.

Shiao, Michael C.↗
NASA NTRS1950

The gas kinetics of very high flight speeds

The aerodynamic forces on bodies of arbitrary shape were investigated under conditions such that the mean free path of the air molecule is greater than the dimensions of the body. Air pressures and friction forces were calculated from gas kinetic theory for surfaces facing both toward and away from the air stream at any angle. Air forces for an atmosphere of definite composition (molecular hydrogen) were calculated as a function of the flight velocity. The results indicate that the friction stresses between the air and the body surface are of the same magnitude as the dynamic pressure and as the air pressures normal to the surface. The application of the general method to the specific cases such as thin airfoils and projectiles leads to high drag coefficients and poor glide ratios even for the theoretically best wing sections.

AIR FLOW VELOCITY - MOLECULAR ENERGIES↗
NASA NTRS1972

Surface temperature effect on subsonic stall.

Results of an analytical and experimental study of boundary layer flow over an aerodynamic surface rejecting heat to a cool environment. This occurs following reentry of a Space Shuttle vehicle. Analytical studies revealed that a surface to freestream temperature ratio, greater than unity tended to destabilize the boundary layer, hastening transition and separation. Therefore, heat transfer accentuated the effect of an adverse pressure gradient. Wind tunnel tests of a 0012-64 NACA airfoil showed that the stall angle was significantly reduced while drag tended to increase for freestream temperature ratios up to 2.2.

Macha, J. M.↗
NASA NTRS1988

Design of low Reynolds number airfoils. I

The low Reynolds number airfoils designated ASM-LRN-003 and -007 have been designed for high section L/D ratios using Drela's (1985) design-and-analysis code; close to 70-percent laminar flow is maintained on the upper surfaces, and 100-percent on the lower, at coefficients of lift of 1.0-1.3, assuming optimum laminar separation and transition control on the upper surface by means of suitable turbulators. If peak performance is critical, airfoils of this type with an undercut front lower surface and a correspondingly sharper leading edge may be resorted to.

Pfenninger, W.↗
NASA NTRS1978

Bounds on thickness and loading noise of rotating blades and the favorable effect of blade sweep on noise reduction

The maxima of amplitudes of thickness and loading noise harmonics are established when the radial distribution of blade chord, thickness ratio, and lift coefficient is specified. It is first shown that only airfoils with thickness distribution and chordwise loading distributions which are symmetric with respect to midchord need be considered for finding the absolute maxima of thickness and loading noise. The resulting chordwise thickness and load distributions for these maximum noise conditions require infinite slope at some points along the chord but otherwise are uniform. It is shown that sweeping the blades reduces the thickness and loading noise, but there is no optimum sweep which generates the lowest noise.

Farassat, F.↗
NASA NTRS1978

A parametric experimental study of the interference effects and the boundary-condition coefficient of slotted wind-tunnel walls

An experimental study of slotted upper and lower walls in a two-dimensional transonic wind tunnel with solid sidewalls is reported. Results are presented for several slot spacings and slot openness ratios. The experimental data are pressure measurements which were made on an airfoil model and on a sidewall near one of the slotted walls. The slotted-wall boundary-condition coefficient, which relates the pressure and streamline curvature near the wall, is determined from the wall pressure measurements. The measured wall-induced interference is correlated with the experimental values for the boundary-condition coefficient. This correlation is compared with theory.

Everhart, J. L.↗
NASA NTRS1978

A parametric experimental study of the slotted-wall boundary condition

An experimental study of slotted upper and lower walls in a two dimensional transonic wind tunnel with solid sidewalls is reported. Results are presented for several slot spacings and slot openness ratios. The experimental data were pressure measurements which were made on an airfoil model and on a sidewall near one of the slotted walls. The slotted-wall boundary condition coefficient, which related the pressure and streamline curvature near the wall, was determined from the wall pressure measurements. The measured wall-induced interference was correlated with the experimental values for the boundary condition coefficient. This correlation was compared with theory.

Everhart, J. L.↗
NASA NTRS1931

Tests of six symmetrical airfoils in the variable density wind tunnel

This paper is the first of a series covering an investigation of a family of airfoils all formed from a basic profile. It gives in preliminary form the results of six symmetrical airfoils, differing only in maximum thickness. The maximum thickness-to-chord ratios are 0.06, 0.09, 0.12, 0.15, 0.18, and 0.21.

Jacobs, Eastman N↗
NASA NTRS1974

Results from cascade thrust reverser noise and suppression experiments

Results from experimental work on model scale cascade reversers with cold airflow are presented. Sound power level directivity and spectral characteristics for cascade reversers are reported. Effect of cascade exit area ratio, vane profile shape, and emission arc are discussed. Model equivalent diameters varied from 3 to 5 inches, pressure ratios range from 1.15 to 3.0. Depending on the reverser type, acoustic power was proportional to the 4 1/2 to 6th power of ideal jet velocity. Reverser noise peaked at higher frequency and was more omnidirectional than nozzle-alone jet noise. Appreciable reduction in sideline noise was obtained from plane shields. Airfoil-vaned cascades were the most aerodynamically efficient and least noisy reversers. Scaling of cascade reverser data to example aircraft engines showed all cascades above the 95 PNdB sideline goal from STOL aircraft. However, the airfoil-vaned reverser has a good potential for meeting this goal for high-bypass (low pressure ratio) exhausts.

Gutierrez, O. A.↗
NASA NTRS1973

Performance of a low-pressure-ratio centrifugal compressor with four diffuser designs

A low-pressure-ratio centrifugal compressor was tested with four different diffuser configurations. One diffuser had airfoil vanes. Two were pipe diffusers. One pipe diffuser had 7.5 deg cone diffusing passages. The other had trumpet-shaped passages designed for linear static-pressure rise from throat to exit. The fourth configuration had flat vanes with elliptical leading edges similar to those of pipe diffusers. The side walls were contoured to produce a linear pressure rise. Peak compressor efficiencies were 0.82 with the airfoil vane and conical pipe diffusers, 0.80 with the trumpet, and 0.74 with the flat-vane design. Surge margin and useful range were greater for the airfoil-vane diffuser than for the other three.

Klassen, H. A.↗
NASA NTRS1980

Experimental verification of propeller noise prediction

Results of experimental measurements of the sound fields of 1/4-scale general aviation propellers are presented and experimental wake surveys and pressure signatures obtained are compared with theoretical predictions. Experiments were performed primarily on a 1C160 propeller model mounted in front of a symmetric body in an anechoic wind tunnel, and measured the thrust and torque produced by propeller at different rotation speeds and tunnel velocities, wakes at three axial distances, and sound pressure at various azimuths and tip speeds with advance ratio or tunnel velocity constant. Aerodynamic calculations of blade loading were performed using airfoil section characteristics and a modified strip analysis procedure. The propeller was then modeled as an array of point sound sources with each point characterized by the force and volume of the corresponding propeller section in order to obtain the acoustic characteristics. Measurements are found to agree with predictions over a wide range of operating conditions, tip speeds and propeller nacelle combinations, without the use of adjustable constants.

Succi, G. P.↗
NASA NTRS1995

Shape optimization of single- and two-element airfoils on multiblock grids

A multiblock, discrete sensitivity analysis method is used to couple a direct optimization method and a flow analysis method. The domain is divided into smaller subdomains for which the sensitivities are obtained separately. Then, an effective sensitivity equation is solved to complete the coupling of all the sensitivity information. The flow analysis is based on the thin-layer Navier-Stokes equations solved by an implicit, upwind-biased, finite-volume method. The method of feasible directions is used for the present gradient-based optimization approach. First, a transonic airfoil is optimized to investigate the behavior of the method in highly nonlinear flows as well as the effect of different blocking strategies on the procedure. A supercritical airfoil is produced from an initially symmetric airfoil with multiblocking affecting the path but not the final shape. Secondly, a two-element airfoil is shape optimized in subsonic flow to demonstrate the present method's capability of shaping aerodynamically interfering elements simultaneously. For a very low and a very high Reynolds number cases, the shape of the main airfoil and the flap are optimized to yield improved lift-to-drag ratios.

Lacasse, James M.↗