Search NASA⌕ Search

SEARCH · Search NASA

Results for “AIRPLANES - DESIGN”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1931

Estimated Effect of Ring Cowl on the Climb and Ceiling of an Airplane, Special Report

Although the application of a ring cowl to an airplane with an air-cooled engine increases the maximum L/D and the high speed to an appreciable extent, the performance in climb and ceiling is not increased as much as one would expect without analyzing the conditions. When a ring cowl is installed on an airplane, the propeller is set at a higher pitch to allow the engine to turn its rated r.p.m. at the increased high speed. V/nD is increased and the propeller efficiency at high speed is increased slightly. The ratio of r.p.m. at climbing speed, V(sub c) , to the r.p.m. at maximum speed, V (sub m) is dependent upon the ratio of V(sub c) to V(sub m). The increase in V(sub c) for all airplane with ring cowl i s not as great as the increase in V(sub m), so that the ratio V(sub c)/V(sub m) is less than for the airplane without ring. Consequently the r.p.m. and full throttle thrust power available are less at V(sub c) for the airplane with ring cowl and in spite of the increase in L/D due to the installation of the ring, the excess thrust power available for climbing is not appreciably changed. The same method of reasoning accounts for the small increase in absolute ceiling in spite of a large increase in L/D maximum.

Louden, F. A.↗
NASA NTRS2011

Radiated Emissions from a Remote-Controlled Airplane-Measured in a Reverberation Chamber

A full-vehicle, subscale all-electric model airplane was tested for radiated emissions, using a reverberation chamber. The mission of the NASA model airplane is to test in-flight airframe damage diagnosis and battery prognosis algorithms, and provide experimental data for other aviation safety research. Subscale model airplanes are economical experimental tools, but assembling their systems from hobbyist and low-cost components may lead to unforseen electromagnetic compatibility problems. This report provides a guide for accommodating the on-board radio systems, so that all model airplane systems may be operated during radiated emission testing. Radiated emission data are provided for on-board systems being operated separately and together, so that potential interferors can be isolated and mitigated. The report concludes with recommendations for EMI/EMC best practices for subscale model airplanes and airships used for research.

Ely, Jay J.↗
NASA NTRS2003

Prolonging Microgravity on Parabolic Airplane Flights

Three techniques have been proposed to prolong the intervals of time available for microgravity experiments aboard airplanes flown along parabolic trajectories. Typically, a pilot strives to keep an airplane on such a trajectory during a nominal time interval as long as 25 seconds, and an experimental apparatus is released to float freely in the airplane cabin to take advantage of the microgravitational environment of the trajectory for as long as possible. It is usually not possible to maintain effective microgravity during the entire nominal time interval because random aerodynamic forces and fluctuations in pilot control inputs cause the airplane to deviate slightly from a perfect parabolic trajectory, such that the freely floating apparatus bumps into the ceiling, floor, or a wall of the airplane before the completion of the parabola.

Robinson, David W.↗
NASA NTRS2019

CASPEr: an Approach to Characterize the Performance of Onboard Airplane Energy State and Automation Mode Prediction Functions

The Commercial Aviation Safety Team (CAST) has identified a set of safety enhancements to mitigate the risks of loss of control in-flight (LOCI) accidents and incidents involving commercial transport airplanes. In support of this, NASA has been developing technologies intended to enhance flight crew awareness of airplane systems, attitude, and energy state. This report describes preliminary ideas for a methodology to assess the goodness of onboard airplane energy state and automation mode prediction functions. The methodology is intended to contribute to the goal of moving these prediction technologies to the readiness level required for transition to industry and reduce the technology certification risks. In addition, this report describes a simulation-based approach named CASPEr (Characterization of Airplane State Prediction Error) to characterize the performance of these predictive functions over a wide range of operational conditions. The first exploratory version of this approach is described. The bulk of the report documents the initial results of tests to characterize the performance of an airplane trajectory prediction function. Future reports will give additional performance characterization results for this function and a complete description of the proposed methodology to assess such functions.

Torres-Pomales, Wilfredo↗
NASA NTRS1934

Effect of the Surface Condition of a Wing on the Aerodynamic Characteristics of an Airplane

In order to determine the effect of the surface conditions of a wing on the aerodynamic characteristics of an airplane, tests were conducted in the N.A.C.A. full-scale wind tunnel on the Fairchild F-22 airplane first with normal commercial finish of wing surface and later with the same wing polished. Comparison of the characteristics of the airplane with the two surface conditions shows that the polish caused a negligible change in the lift curve, but reduced the minimum drag coefficient by 0.001. This reduction in drag if applied to an airplane with a given speed of 200 miles per hour and a minimum drag coefficient of 0.025 would increase the speed only 2.9 miles per hour, but if the speed remained the same, the power would be reduced 4 percent.

AIRPLANES - FAIRCHILD 22 (Amer ) WIND TUNNEL TEST↗
NASA NTRS2011

AVIATR - Aerial Vehicle for In-situ and Airborne Titan Reconnaissance A Titan Airplane Mission Concept

We describe a mission concept for a stand-alone Titan airplane mission: Aerial Vehicle for In-situ and Airborne Titan Reconnaissance (AVIATR). With independent delivery and direct-to-Earth communications, AVIATR could contribute to Titan science either alone or as part of a sustained Titan Exploration Program. As a focused mission, AVIATR as we have envisioned it would concentrate on the science that an airplane can do best: exploration of Titan's global diversity. We focus on surface geology/hydrology and lower-atmospheric structure and dynamics. With a carefully chosen set of seven instruments-2 near-IR cameras, 1 near-IR spectrometer, a RADAR altimeter, an atmospheric structure suite, a haze sensor, and a raindrop detector-AVIATR could accomplish a significant subset of the scientific objectives of the aerial element of flagship studies. The AVIATR spacecraft stack is composed of a Space Vehicle (SV) for cruise, an Entry Vehicle (EV) for entry and descent, and the Air Vehicle (AV) to fly in Titan's atmosphere. Using an Earth-Jupiter gravity assist trajectory delivers the spacecraft to Titan in 7.5 years, after which the AVIATR AV would operate for a 1-Earth-year nominal mission. We propose a novel 'gravity battery' climb-then-glide strategy to store energy for optimal use during telecommunications sessions. We would optimize our science by using the flexibility of the airplane platform, generating context data and stereo pairs by flying and banking the AV instead of using gimbaled cameras. AVIATR would climb up to 14 km altitude and descend down to 3.5 km altitude once per Earth day, allowing for repeated atmospheric structure and wind measurements all over the globe. An initial Team-X run at JPL priced the AVIATR mission at FY10 $715M based on the rules stipulated in the recent Discovery announcement of opportunity. Hence we find that a standalone Titan airplane mission can achieve important science building on Cassini's discoveries and can likely do so within a New Frontiers budget.

UAV↗
NASA NTRS1973

Evaluation of an aeroelastic model technique for predicting airplane buffet loads

A wind-tunnel technique which makes use of a dynamically scaled aeroelastic model to predict full-scale airplane buffet loads during buffet boundary penetration is evaluated. A 1/8-scale flutter model of a fighter airplane with remotely controllable variable-sweep wings and trimming surfaces was used for the evaluation. The model was flown on a cable-mount system which permitted high lift forces comparable to those in maneuvering flight. Bending moments and accelerations due to buffet were measured on the flutter model and compared with those measured on the full-scale airplane in an independent flight buffet research study. It is concluded that the technique can provide valuable information on airplane buffet load characteristics not available from any other source except flight test.

Hanson, P. W.↗
NASA NTRS1973

Evaluation of glide paths for landing a VTOL airplane using linear regulator theory.

A method of evaluating certain characteristics of approach paths for VTOL airplanes is presented which is based on the solution of the matrix Riccati equation to obtain an optimal state variable feedback controller. The longitudinal equations of motion of the airplane are linearized about a preselected path and the resulting system of equations is treated as a linear, time-varying regulator. The controller which minimizes a quadratic cost function is applied to the linearized system to determine the airplane's ability to return to the prescribed path given a specified initial error in altitude. The procedure is applied to the XC-142A, tilt-wing, V/STOL airplane, under decelerating approach conditions with a glide path consisting of two segments, the first having a smaller angle of descent than the second.

Reid, G. F.↗
NASA NTRS1973

Performance of a ballute decelerator towed behind a jet airplane

An F-104B airplane was modified to investigate the drag and stability characteristics of a ballute decelerator in the wake of an asymmetrical airplane. Decelerator deployments were initiated at a Mach number of 1.3 and an altitude of 15,240 meters (50,000 feet) and terminated when the airplane had decelerated to a Mach number of 0.5. The flight tests indicated that the decelerator had a short inflation time with relatively small opening forces. The drag levels attained with the subject decelerator were less than those obtained with other high-speed decelerators behind a symmetrical tow vehicle. The ballute demonstrated good stability characteristics behind the testbed airplane.

Pyle, J. S.↗
NASA NTRS1974

Study of stability of large maneuvers of airplanes

A predictive method of nonlinear system analysis is used to investigate airplane stability and dynamic response during rolling maneuvers. The maneuver roll-rate is not assumed to be constant, and the airplane motion is represented by a set of coupled nonlinear differential equations. The general rolling maneuver is kinematically specified by its roll-rate variation p(t). A method for relating the airplane dynamic response to p(t) is developed. The method provides analytical expressions for the motion variables in terms of the maneuver descriptor p(t). A parameterized family of rolling maneuvers is considered, for which the method is used to predict specific dynamic response information, such as the dependence of the peak angle-of-attack excursion on the maneuver parameters. The stability and motion of the airplane in response to an arbitrary actuation of aileron input is considered. Analytical expressions relating motion variables to aileron input are obtained. Explicit analytical bounds on the motion variables are derived. A stability criterion which guarantees nondivergence of motion in response to aileron actuation is presented.

Haddad, E. K.↗
NASA NTRS1974

Measurements of sonic booms generated by an airplane flying at Mach 3.5 and 4.8

Sonic booms generated by the X-15 airplane flying at Mach numbers of 3.5 and 4.8 were measured. The experimental results agreed within 12 percent with results obtained from theoretical methods. No unusual phenomena related to overpressure were encountered. Scaled data from the X-15 airplane for Mach 4.8 agreed with data for an SR-71 airplane operating at lower Mach numbers and similar altitudes. The simple technique used to scale the data on the basis of airplane lift was satisfactory for comparing X-15 and SR-71 sonic boom signatures.

Green, K. S.↗
NASA NTRS1974

Simulation studies of STOL airplane operations in metropolitan downtown and airport air traffic control environments

The operating problems and equipment requirements for STOL airplanes in terminal area operations in simulated air traffic control (ATC) environments were studied. These studies consisted of Instrument Flight Rules (IFR) arrivals and departures in the New York area to and from a downtown STOL port, STOL runways at John F. Kennedy International Airport, or STOL runways at a hypothetical international airport. The studies were accomplished in real time by using a STOL airplane flight simulator. An experimental powered lift STOL airplane and two in-service airplanes having high aerodynamic lift (i.e., STOL) capability were used in the simulations.

Sawyer, R. H.↗
NASA NTRS1975

Noise reduction studies for the U-10 airplane

A study was undertaken by the NASA Langley Research Center to determine the noise reduction potential of the U-10 airplane in order to reduce its aural detection distance. Static and flyover noise measurements were made to document the basic airplane noise signature. Two modifications to the airplane configuration are suggested as having the best potential for substantially reducing aural detection distance with small penalty to airplane performance or stability and control. These modifications include changing the present 3-blade propeller to a 5-blade propeller, changing the propeller diameter, and changing the propeller gear ratio, along with the use of an engine exhaust muffler. The aural detection distance corresponding to normal cruising flight at an altitude of 1,000 ft over grassy terrain is reduced from 28,000 ft (5.3 miles) to about 50 percent of that value for modification 1, and to about 25 percent for modification 2. For the aircraft operating at an altitude of 300 ft, the analysis indicates that relatively straightforward modifications could reduce the aural detection distance to approximately 0.9 mile. Operation of the aircraft at greatly reduced engine speed (1650 rpm) with a 1.3-cu-ft muffler provides aural detection distances slightly lower than modification 1.

Hilton, D. A.↗
NASA NTRS1975

A noise study of the A-6 airplane and techniques for reducing its aural detection distance

A study was undertaken to determine the noise reduction potential of the A-6 airplane in order to reduce its aural detection distance. Static and flyby noise measurements were taken to document the basic airplane signature. The low-frequency noise which is generally most critical for aural detection was found to be broad-band in nature from this airplane, and its source is the turbojet engine exhaust. High-frequency compressor noise, which is characteristic of turbojet powerplants, and which is prominent at close range for this airplane, has no measurable effect on aural detection distance. The use of fluted-engine exhaust nozzles to change the far-field noise spectra is suggested as a possible means for reducing the aural detection distances. Detection distances associated with eight-lobe and four-lobe nozzles are estimated for a 1,000-foot altitude and grassy terrain to decrease from 4 miles to about 3 miles, and from 3 miles to about 2 miles for a 300-foot altitude and grassy terrain.

Hilton, D. A.↗
NASA NTRS1976

An analytical study and wind tunnel tests of an aeromechanical gust-alleviation system for a light airplane

The results of an analytical study of a system using stability derivatives determined in static wind tunnel tests of a 1/6 scale model of a popular, high wing, light airplane equipped with the gust alleviation system are reported. The longitudinal short period mode dynamics of the system are analyzed, and include the following: (1) root loci, (2) airplane frequency responses to vertical gusts, (3) power spectra of the airplane responses in a gust spectrum, (4) time history responses to vertical gusts, and (5) handling characteristics. The system reduces the airplane's normal acceleration response to vertical gusts while simultaneously increasing the pitching response and reducing the damping of the longitudinal short period mode. The normal acceleration response can be minimized by using the proper amount of static alleviation and a fast response system with a moderate amount of damping. The addition of a flap elevator interconnect or a pitch damper system further increases the alleviation while moderating the simultaneous increase in pitching response. The system provides direct lift control and may reduce the stick fixed longitudinal static stability.

Stewart, E. C.↗
NASA NTRS1977

Buffet characteristics of the F-8 supercritical wing airplane

The buffet characteristics of the F-8 supercritical wing airplane were investigated. Wing structural response was used to determine the buffet characteristics of the wing and these characteristics are compared with wind tunnel model data and the wing flow characteristics at transonic speeds. The wingtip accelerometer was used to determine the buffet onset boundary and to measure the buffet intensity characteristics of the airplane. The effects of moderate trailing edge flap deflections on the buffet onset boundary are presented. The supercritical wing flow characteristics were determined from wind tunnel and flight static pressure measurements and from a dynamic pressure sensor mounted on the flight test airplane in the vicinity of the shock wave that formed on the upper surface of the wing at transonic speeds. The comparison of the airplane's structural response data to the supercritical flow characteristics includes the effects of a leading edge vortex generator.

Deangelis, V. M.↗
NASA NTRS1978

Simulation study of the oscillatory longitudinal motion of an airplane at the stall

Hybrid simulation of the longitudinal motion of a straight-wing airplane at the stall was studied to investigate the effect of hysteresis in the development of lift and pitching moments on the wing as a function of angle of attack on the occurrence of longitudinal oscillations at the stall. Flight data for the simulated airplane and for various other airplanes are shown for the simulated airplane and for comparison. The results show that oscillations similar to those measured in flight may be obtained by incorporating hysteresis in the lift and pitching-moment curves.

Phillips, W. H.↗
NASA NTRS1979

Precision controllability of the F-15 airplane

A flying qualities evaluation conducted on a preproduction F-15 airplane permitted an assessment to be made of its precision controllability in the high subsonic and low transonic flight regime over the allowable angle of attack range. Precision controllability, or gunsight tracking, studies were conducted in windup turn maneuvers with the gunsight in the caged pipper mode and depressed 70 mils. This evaluation showed the F-15 airplane to experience severe buffet and mild-to-moderate wing rock at the higher angles of attack. It showed the F-15 airplane radial tracking precision to vary from approximately 6 to 20 mils over the load factor range tested. Tracking in the presence of wing rock essentially doubled the radial tracking error generated at the lower angles of attack. The stability augmentation system affected the tracking precision of the F-15 airplane more than it did that of previous aircraft studied.

Sisk, T. R.↗