Search NASA⌕ Search

SEARCH · Search NASA

Results for “AIRPLANES - DESIGN & THEORY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1959

Ground Measurements of the Shock-Wave Noise from Airplanes in Level Flight at Mach Numbers to 1.4 and at Altitudes to 45000 Feet

Time histories of noise pressures near ground level were measured during flight tests of fighter-type airplanes over fairly flat, partly wooded terrain in the e Mach number range between 1.13 and 1.4 and at altitudes from 25,000 to 45,000 feet. Atmospheric soundings and radar tracking studies were made for correlation with the measured noise data. The measured and calculated values of the pressure rise across the shock wave were generally in good agreement. There is a tendency for the theory to overestimate the pressure at locations remote from the track and to underestimate the pressures for conditions of high tailwind at altitude. The measured values of ground-reflection factor averaged about 1.8 f or the surface tested as compared to a theoretical value of 2.0. P o booms were measured in all cases. The observers also generally reported two booms; although, in some cases, only one boom was reported. The shock-wave noise associated with some of the flight tests was judged to be objectionable by ground observers, and in one case the cracking of a plate-glass store window was correlated in time with the passage of the airplane at an altitude of 25,000 feet.

Maglieri, Domenic J.↗
NASA NTRS1952

Hydrodynamic impact of a system with a single elastic mode I : theory and generalized solution with an application to an elastic airframe

Solutions of impact of a rigid prismatic float connected by a massless spring to a rigid upper mass are presented. The solutions are based on hydrodynamic theory which has been experimentally confirmed for a rigid structure. Equations are given for defining the spring constant and the ratio of the sprung mass to the lower mass so that the two-mass system provides representation of the fundamental mode of an airplane wing. The forces calculated are more accurate than the forces which would be predicted for a rigid airframe since the effect of the fundamental mode on the hydrodynamic force is taken into account. In a comparison of the theoretical data with data for a severe flight-test landing impact, the effect of the fundamental mode on the hydrodynamic force is considered and response data are compared with experimental data.

Mayo, Wilbur L↗
NASA NTRS2002

Control of Initialized Fractional-Order Systems

Due to the importance of historical effects in fractional-order systems, this paper presents a general fractional-order control theory that includes the time-varying initialization response. Previous studies have not properly accounted for these historical effects. The initialization response, along with the forced response, for fractional-order systems is determined. Stability properties of fractional-order systems are presented in the complex Airplane, which is a transformation of the s-plane. Time responses are discussed with respect to pole positions in the complex Airplane and frequency response behavior is included. A fractional-order vector space representation, which is a generalization of the state space concept, is presented including the initialization response. Control methods for vector representations of initialized fractional-order systems are shown. Nyquist, root-locus, and other input-output control methods are adapted to the control of fractional-order systems. Finally, the fractional-order differintegral is generalized to continuous order-distributions that have the possibility of including a continuum of fractional orders in a system element.

Hartly, Tom T.↗
NASA NTRS1950

Transonic Stability and Control Investigation of a 1/80-Scale Model of the Consolidated Vultee Skate 9 Seaplane, TED No. NACA DE 345: Transonic-Bump Method

An investigation of the longitudinal stability and of the all-movable horizontal tail and aileron control of a 1/80-scale reflection-plane model of the Consolidated Vultee Skate 9 seaplane has been made through a Mach number range of 0.6 to 1.16 on the transonic bump of the Langley high-speed 7- by 10-foot tunnel. At moderate lift coefficients (0.4 to 0.8) and below a Mach number of 1.0 the model was statically unstable longitudinally. The static longitudinal stability of the model at low lift coefficients increased with Mach number corresponding to a shift in aerodynamic center from 37 percent mean aerodynamic chord at a Mach number of 0.60 to 64 percent at a Mach number of 1.10. Estimates indicate that the tail deflection angle required for steady flight and for accelerated maneuvers of the Skate 9 airplane would probably not vary greatly with Mach number at sea level, but for accelerated maneuvers at altitude the tail deflection angle would probably vary erratically with Mach number. The variation of rolling-moment coefficient with aileron deflection angle was approximately linear, agreed well with theory, and held for the range of aileron deflections tested (-17.1 deg to 16.6 deg). At low lift coefficients the drag rise occurred at Mach numbers of 0.95 and 0.90 for the wing alone and the complete model, respectively. The effects of the canopy on the model were small. For the ranges investigated, angle-of-attack and Mach number changes caused no large pressure drops in the jet-engine duct.

Riebe, John M.↗
NASA NTRS1956

Lift and Pitching-moment Interference Between a Pointed Cylindrical Body and Triangular Wings of Various Aspect Ratios at Mach Numbers of 1.50 and 2.02

The lift and pitching-moment characteristics of a body alone, six triangular wings of various aspect ratios, and the combinations were measured at Mach numbers of 1.50 and 2.02 at a Reynolds number of 5.5 million (based on the body length) for angles of attack up to 5.5 degrees. The total lift and pitching-moment interference were determined and compared with theory. The agreement was found to be good.

RESEARCH TECHNIQUE - CORRECTIONS↗
NASA NTRS1939

Contribution to the theory of the heated duct radiator

A method is developed with no neglect of certain factors in mass flow of air and in the drag of the heated radiator, i.e., one under actual operating conditions, as compared with the corresponding values in the cold state, may be simply computed. Although a symmetrical duct radiator has been used to bring out the flow relations, the results apply equally as well to the unsymmetrical radiator shapes usual in airplane construction.

Winter, H↗
NASA NTRS1995

Decision Making in the Airplane

The Importance of decision-making to safety in complex, dynamic environments like mission control centers, aviation, and offshore installations has been well established. NASA-ARC has a program of research dedicated to fostering safe and effective decision-making in the manned spaceflight environment. Because access to spaceflight is limited, environments with similar characteristics, including aviation and nuclear power plants, serve as analogs from which space-relevant data can be gathered and theories developed. Analyses of aviation accidents cite crew judgement and decision making as causes or contributing factors in over half of all accidents. Yet laboratory research on decision making has not proven especially helpful In improving the quality of decisions in these kinds of environments. One reason is that the traditional, analytic decision models are inappropriate to multi-dimensional, high-risk environments, and do not accurately describe what expert human decision makers do when they make decisions that have consequences. A new model of dynamic, naturalistic decision making is offered that may prove useful for improving decision making in complex, isolated, confined and high-risk environments. Based on analyses of crew performance in full-mission simulators and accident reports, features that define effective decision strategies in abnormal or emergency situations have been identified. These include accurate situation assessment (including time and risk assessment), appreciation of the complexity of the problem, sensitivity to constraints on the decision, timeliness of the response, and use of adequate information. More effective crews also manage their workload to provide themselves with time and resources to make good decisions. In brief, good decisions are appropriate to the demands of the situation. Effective crew decision making and overall performance are mediated by crew communication. Communication contributes to performance because it assures that all crew members have essential information, but it also regulates and coordinates crew actions and is the medium of collective thinking In response to a problem, This presentation will examine the relations between leadership, communication, decision making and overall crew performance. Implications of these findings for training will be discussed.

Orasanu, Judith↗
NASA NTRSDate not supplied

Validation of Actuator Disk, Actuator Line and Sliding Mesh Methods within the LAVA Solver

In this study the implementation of actuator-disk, actuator-line and sliding-mesh methodologies in the Launch Ascent and Vehicle Aerodynamics (LAVA) solver is described and validated against several test-cases. The different models are validated against available numerical as well as experimental data. Both steady and unsteady Reynolds-Averaged Navier-Stokes (RANS) simulations using the Spallart Allmaras (SA) turbulence model are performed for several different configurations representative of aeroscience applications. The first part of the paper is focused on the verification and validation of the implemented propulsor models. The first validation case is a theoretical rotor in hover, compared with the 1D analytical solution derived from momentum theory. The second validation is the Rotor-Airframe Interaction Model of Georgia Institute of Technology (GIT), representing the application of actuator disks to top-mounted rotorcraft vehicles or unmanned aerial vehicles (UAVs). The third case is a representative configuration for tip-mounted rotor-craft vehicles such as NASA’s X57 airplane. The second part of the paper shows the implemented models applied to realistic engineering configurations such as NASA’s X57 airplane and the R4 Advanced Ducted Propellor (ADT). A modification to the actuator line method in order to represent the blade geometry more closely is proposed and comparisons with simulations modeling the blade utilizing a sliding-mesh approach are made.

ARMD↗
NASA NTRS1976

FLEXSTAB: A computer program for the prediction of loads and stability and control of flexible aircraft

Capabilities of the FLEXSTAB Computer Program System are described and illustrated. Aeroelastic analysis of a wide variety of aircraft configurations is performed. The aerodynamic theory used in FLEXSTAB is applicable to both steady and unsteady, subsonic and supersonic flow for multiple wing-body tail nacelle configurations with a plane of symmetry. For unsteady flow calculations, an unsteady aerodynamic theory is used which is appropriate for the low reduced frequencies associated with aircraft flight dynamics. The aircraft is modeled as either a rigid or flexible structure. The computer trims the aircraft in steady reference flight and computes both static and dynamic stability and control derivatives and the stability behavior about the trim condition. The airplane lifting pressure distribution, aerodynamic and inertia loads and deflected shape are also computed.

Perkin, B. R.↗
NASA NTRS1992

CFD Simulations Of Sonic Booms In Near And Mid Fields

Report discusses computational fluid dynamics (CFD) to simulate generation and propagation of sonic booms in near- and mid-field regions of supersonic flows about simplified bodies representative of advanced airplanes. Parabolized Navier-Stokes equations integrated by implicit, approximate-factorization, finite-volume algorithm in which crossflow inviscid fluxes evaluated by Roe's flux-difference-splitting scheme. Near-field solutions obtained by applying algorithm to flows immediately surrounding bodies. Solutions transferred to computer codes based on Whitham"s F-function theory for extrapolation to far-field.

Cheung, Samson H.↗
NASA NTRS1955

Full-scale-wind-tunnel Tests of a 35 Degree Sweptback Wing Airplane with High-velocity Blowing over the Training-edge Flaps

A wind-tunnel investigation was made to determine the effects of ejecting high-velocity air near the leading edge of plain trailing-edge flaps on a 35 degree sweptback wing. The tests were made with flap deflections from 45 degrees to 85 degrees and with pressure ratios across the flap nozzles from sub-critical up to 2.9. A limited study of the effects of nozzle location and configuration on the efficiency of the flap was made. Measurements of the lift, drag, and pitching moment were made for Reynolds numbers from 5.8 to 10.1x10(6). Measurements were also made of the weight rate of flow, pressure, and temperature of the air supplied to the flap nozzles.The results show that blowing on the deflected flap produced large flap lift increments. The amount of air required to prevent flow separation on the flap was significantly less than that estimated from published two-dimensional data. When the amount of air ejected over the flap was just sufficient to prevent flow separation, the lift increment obtained agreed well with linear inviscid fluid theory up to flap deflections of 60 degrees. The flap lift increment at 85 degrees flap deflection was about 80 percent of that predicted theoretically.With larger amounts of air blown over the flap, these lift increments could be significantly increased. It was found that the performance of the flap was relatively insensitive to the location of the flap nozzle, to spacers in the nozzle, and to flow disturbances such as those caused by leading-edge slats or discontinuities on the wing or flap surfaces. Analysis of the results indicated that installation of this system on an F-86 airplane is feasible.

Kelley, Mark W↗
NASA NTRS1968

Briefing on Sonic Boom and Aircraft Noise

This document is a presentation for a NAS-NRC committee on the SuperSonic Transport (SST) sonic boom. It consists of copies of the slides presented during the briefing. The topics covered in reference to Sonic Booms are: the result of sonic boom results on generation and propagation, the atmospheric effects, flight research and laboratory research and prediction theory developments, the structural responses, seismic responses and simulation and human factors from the recent research on the effects of sonic booms, Domestic SST, and evaluation of certain minimum boom concepts from advanced configuration studies. The topics covered in the aircraft noise section are studies on compressor noise reduction, acoustic treatment of nacelle ducts, some technical problems of airplane certification and studies relating to subjective responses.

Source record↗
NASA NTRS2006

Analyzing Aeroelastic Stability of a Tilt-Rotor Aircraft

Proprotor Aeroelastic Stability Analysis, now at version 4.5 (PASTA 4.5), is a FORTRAN computer program for analyzing the aeroelastic stability of a tiltrotor aircraft in the airplane mode of flight. The program employs a 10-degree- of-freedom (DOF), discrete-coordinate, linear mathematical model of a rotor with three or more blades and its drive system coupled to a 10-DOF modal model of an airframe. The user can select which DOFs are included in the analysis. Quasi-steady strip-theory aerodynamics is employed for the aerodynamic loads on the blades, a quasi-steady representation is employed for the aerodynamic loads acting on the vibrational modes of the airframe, and a stability-derivative approach is used for the aerodynamics associated with the rigid-body DOFs of the airframe. Blade parameters that vary with the blade collective pitch can be obtained by interpolation from a user-defined table. Stability is determined by examining the eigenvalues that are obtained by solving the coupled equations of motions as a matrix eigenvalue problem. Notwithstanding the relative simplicity of its mathematical foundation, PASTA 4.5 and its predecessors have played key roles in a number of engineering investigations over the years.

Kvaternil, Raymond G.↗
NASA NTRS1939

Investigation of the lift distribution over the separate wings of a biplane

An investigation is made of the mutual interference of the wings of a biplane under the general assumption that each wing may be replaced by a vortex system of the type given by the Prandtl wing theory. The additional velocities induced at each wing by the presence of the other are determined by the Biot-Savart law and converted into an equivalent change in the angle of attack, the effect being that of an additional twist given to the wings in changing their lift distributions. The lift distributions computed in this manner for several airplane types are compared with the results of measurement.

Kuchemann, D↗
NASA NTRS1942

Theory of heat transfer and hydraulic resistance of oil radiators

In the present report the coefficients of heat transfer and hydraulic resistance are theoretically obtained for the case of laminar flow of a heated viscous liquid in a narrow rectangular channel. The results obtained are applied to the computation of oil radiators, which to a first approximation may be considered as made up of a system of such channels. In conclusion, a comparison is given of the theoretical with the experimental results obtained from tests on airplane oil radiators.

Mariamov, N B↗
NASA NTRS1953

The Effects on Dynamic Lateral Stability and Control of Large Artificial Variations in the Rotary Stability Derivatives

This report presents the results of an investigation conducted in the Langley free-flight tunnel to determine the effects of large artificial variations of several rotary lateral-stability derivatives on the dynamic lateral stability and control characteristics of a 45 degree sweptback-wing airplane model. Calculations of the period and damping of the lateral motions and of the response to roll and yaw disturbances were made for correlation with the experimental results. The calculated results were in qualitative agreement with the experimental results in predicting the general trends in flight characteristics produced by large changes in the stability derivatives, but in some cases the theory with the assumption of zero lag was not in good quantitative agreement with the experimental results.

Schade, Robert O↗
NASA NTRS1956

High-temperature oxidation and ignition of metals

A study of the high-temperature oxidation of several aircraft construction materials was undertaken to assess the possibility of ignition under high-temperature flight conditions.Tests have been made both in open and closed jets, and, in addition, the burning of metals has been observed under static conditions in a pressurized vessel containing either air, oxygen, or nitrogen. When heated in an atmosphere of oxygen or when heated and plunged into a supersonic airstream, titanium, iron, carbon steel, and common alloys such as 4130 were found to have spontaneous-ignition temperatures in the solid phase (below melting) and they melted rapidly while burning. Inconel, copper, 18-8 stainless steel, Monel, and aluminum could not be made to ignite spontaneously at temperatures up to melting with the equipment available. Magnesium ignited spontaneously in either type of test at temperatures just above the melting temperature.A theory for the spontaneous ignition of metals, based on the first law of thermodynamics, is presented. Good correlation was obtained between calculated spontaneous-ignition temperatures and values measured in supersonic jet tests. There appears at the present time to be no need for concern regarding the spontaneous ignition of Inconel, the stainless steels, copper, aluminum, or magnesium for ordinary supersonic airplane or missile applications where the material temperature is kept within ordinary structural limits or at least below melting. For hypersonic applications where the material is to be melted away to absorb the heat of convection, the results of the present tests do not apply sufficiently to allow a conclusion.

Hill, Paul R↗