Search NASA⌕ Search

SEARCH · Search NASA

Results for “ANNULAR SPACE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

Numerical generation of two-dimensional orthogonal curvilinear coordinates in an Euclidean space

A noniterative method for the numerical generation of orthogonal curvilinear coordinates for plane annular regions between two arbitrary smooth closed curves was developed. The basic generating equation is the Gaussian equation for an Euclidean space which is solved analytically. The method is applied in many cases and these test results demonstrate that the proposed method can be readily applied to a wide variety of problems. The method can also be used for simply connected regions only by obtaining the solution of the linear equation under the changed boundary conditions.

Warsi, Z. U. A.↗

Experimental Investigation of Interactions Between Two Closely Spaced Azimuthal Modes in a Multinozzle Can Combustor

Thermoacoustic instabilities in annular or circular combustors are often coupled with azimuthal modes. These modes can be characterized by a spin ratio (SR), which quantifies the dominant mode between two counter-rotating waves, and a phase difference between them, which is directly related to the orientation of the antinodal line. This study investigates the instability amplitudes, SR, and phase difference of two closely spaced (3% of their mean frequency), yet distinct azimuthal modes; one is the first azimuthal (1A) mode, and the other is a combination of first azimuthal and first longitudinal (1A1L) mode. Each mode itself consists of two peaks that are spaced even more closely in frequency (0.8%). Furthermore, distinct harmonics at 2× and 3× of these frequencies, presumably associated with nonlinearities, are also evident in the spectra. Each mode is bandpass filtered in spectrum to analyze them separately. For the 1A mode, the SR and phase difference exhibit a variety of behaviors—including quasi-periodic standing waves, spinning waves, and intermittency—depending on operating conditions such as thermal power and azimuthal fuel staging. Similar trends are observed for the 1A1 L mode. Moreover, there is clear coupling between the 1A and 1A1 L modes, as their SRs are almost synchronized during the quasi-periodic standing wave. This synchronization is observed in phase differences as well, but not in the instability amplitude. For spinning dominant wave conditions, the SRs of each mode have similar average values, but they fluctuate in a seemingly random fashion. For the phase difference, both average and fluctuation are not correlated. In contrast, the instability amplitudes are strongly correlated, with modulation of the 1A mode leading to that of the 1A1 L mode. Furthermore, these results clearly indicate that complex coupling occurs across closely spaced frequencies under instability conditions, coupling that must be understood in order to capture limit cycle dynamics.

33 ADVANCED PROPULSION SYSTEMS↗

Brushless machine having ferromagnetic side plates and side magnets

An apparatus is provided having a cylindrical stator and a rotor that is spaced from a stator to define an annular primary air gap that receives AC flux from the stator. The rotor has a plurality of longitudinal pole portions disposed parallel to the axis of rotation and alternating in polarity around a circumference of the rotor. Each longitudinal pole portion includes portions of permanent magnet (PM) material and at least one of the longitudinal pole portions has a first end and an opposing second end and a side magnet is disposed adjacent the first end and a side pole is disposed adjacent the second end.

47 OTHER INSTRUMENTATION↗

Jet Mixing and Emission Characteristics of Transverse Jets in Annular and Cylindrical Confined Crossflow

Three dimensional turbulent reacting CFD analyses were performed on transverse jets injected into annular and cylindrical (can) confined crossflows. The goal was to identify and assess mixing differences between annular and can geometries. The approach taken was to optimize both annular and can configurations by systematically varying orifice spacing until lowest emissions were achieved, and then compare the results. Numerical test conditions consisted of a jet-to-mainstream mass-flow ratio of 3.2 and a jet-to-mainstream momentum-flux ratio (J) of 30. The computational results showed that the optimized geometries had similar emission levels at the exit of the mixing section although the annular configuration did mix-out faster. For lowest emissions, the density correlation parameter (C = (S/H) square root of J) was 2.35 for the annular geometry and 3.5 for the can geometry. For the annular geometry, the constant was about twice the value seen for jet mixing at low mass-flow ratios (i.e., MR less than 0.5). For the can geometry, the constant was about 1 1/2 times the value seen for low mass-flow ratios.

Bain, D. B.↗

An analytical investigation of a conceptual design for the station transverse boom rotary joint structure

A study was conducted to define an annular ring, discrete roller assembly concept for the space station transverse boom rotary joint. The concept was analyzed using closed-form and finite element techniques, to size structural members for a range of joint diameters and to determine necessary equivalent stiffnesses for the roller assemblies. Also, a mass study of the system was conducted to determine its practicality, and maximum loads in the joint were identified. To obtain the optimum balance between high stiffness and low structural mass in the design of the rotary joint, it is necessary to maximize the diameter of the annular ring within operational constraints (i.e., shuttle cargo bay size). Further, a rotary joint designed with the largest possible ring diameter will result in minimum operational loads in both the roller assemblies and the transition truss members while also allowing minimum design stiffnesses for the roller assemblies.

Lake, M. S.↗

Optimal maneuvering and fine pointing control of large space telescope with a new magnetically suspended, single gimballed momentum storage device

This paper considers the application of an Annular Momentum Control Device (AMCD) to both fine pointing and large-angle maneuvering of a large space telescope (LST). The AMCD, which consists principally of a spinning rim suspended in noncontacting electromagnetic bearings, represents a new development in momentum storage devices. A nonlinear mathematical model of the AMCD/LST system is derived. An optimal stochastic fine-pointing controller is designed via LQG theory and the minimum-energy maneuvering problem is solved via a gradient technique. Number of state variable and control variable constraints, as well as all trigonometric nonlinearities, are considered in the latter part.

Nadkarni, A. A.↗

Linear and nonlinear analysis of orbital telescope/space shuttle dynamics and control

Work completed on the design and study of an annular suspension and pointing (ASP) system for the space shuttle was presented. This system makes use of a magnetically suspended vernier pointing assembly. The following objectives were pursued in this study: (1) development of a detailed mathematical model of the Space Shuttle/ASP system, (2) design of control laws in order to obtain the desired pointing performance, and (3) prediction of the statistical pointing accuracies in the presence of stochastic disturbances such as crew-motion, and sensor and actuator noise. The first two of these objectives are documented in this report.

Roberts, A. S., Jr.↗

Design of the annular suspension and pointing system /ASPS/ through decoupling and pole placement

A decoupling and pole-placement technique has been developed for the Annular Suspension and Pointing System (ASPS) of the Space Shuttle which uses bandwidths as performance criteria. The dynamics of the continuous-data ASPS allows the three degrees of freedom to be totally decoupled by state feedback through constant gains, so that the bandwidth of each degree of freedom can be independently specified without interaction. Although it is found that the digital ASPS cannot be completely decoupled, the bandwidth requirements are satisfied by pole placement and a trial-and-error method based on approximate decoupling.

Kuo, B. C.↗

Control of large space structures using Annual Momentum Control Devices (AMCD's)

A controller design approach for large space structures, which proposes the use of several Annular Momentum Control Devices (AMCD's) for structural damping enhancement, and either torque actuators of AMCD's for primary attitude control, was investigated. The damping enhancement controller makes the system asymptotically stable under certain relatively simple conditions. The closed-loop stability of the system with the primary attitude controller as well as the overall controller was established. It is shown that the same AMCD's can be used for the actuation of the damping enhancement controller and the primary attitude controller. Numerical results were obtained for a finite-element model of a large, thin, completely free, flat aluminum plate.

Joshi, S. M.↗

Effects of flexibility on AGS performance

The Marshall Space Flight Center has had under development the Annular Suspension Pointing System Gimbal System (AGS) since early 1979. The AGS is an Orbiter cargo bay mounted subarcsecond 3 axis inertial pointer that can accommodate a wide range of payloads which require more stringent pointing than the Orbiter can provide. This paper will describe the AGS, state performance requirements and the control law configuration. Then an approach to investigating the flexible body effects on control system design will be discussed.

Shelton, H. L.↗

Solidification Interface Shape and Location During Processing in High Gradient Furnace with Quench

High Gradient Furnace with Quench (HGFQ) is being developed to facilitate metals processing experiments aboard the International Space Station. The sample is centered in an annular furnace and is held fixed during processing. The furnace itself is made to translate over the sample. Once in process, heat will flow through the sample from the Heater Zone to the Chill Zone. If operating conditions are correct, the solidification interface will stand in the gradient zone. Objectives of the HGFQ process are to provide a high gradient for the solidification with the solidification interface properly positioned in the gradient zone. At the recent RDR for HGFQ, one of the panelists raised the question about the suitability of HGFQ for potential future PIs. Specifically, it was stated by the design team at RDR that the present HGFQ design would provide a radius of curvature of the solidification interface of at least one sample diameter. The RDR panel argued that this was too small, and that most investigators would need a radius of curvature larger than this. The requirements established by the current PIs are shown. These requirements do not contain any specification about the interface shape. However, these requirements do define the envelope of operational parameters for HGFQ. The objectives of the present investigation are to 1) determine a suitable means of quantifying the interface shape, and 2) investigate the interface shape and how it is affected by processing parameters. The processing parameters to be considered are 1) sample material, 2) sample diameter, and 3) gradient zone length.

Woodbury, Keith A.↗

Low NO.sub.x combustor

A combustor includes a dome assembly having radially outer and inner liners joined thereto and defining therebetween a combustion zone. The dome assembly includes at least one annular dome having a pair of axially extending first flanges between which are disposed a plurality of circumferentially spaced apart carburetors for discharging a fuel/air mixture into the combustion zone for generating combustion gases. An annular heat shield includes a pair of axially extending legs integrally joined to a radially extending face in a generally U-shaped configuration, with the face including a plurality of circumferentially spaced apart ports disposed concentrically with perspective ones of the carburetors for allowing the fuel/air mixture to be discharged therefrom through the heat shield. At least one of the heat shield legs includes a plurality of circumferentially spaced apart mounting holes disposed adjacent to a respective one of the dome flanges, and a plurality of mounting pins are fixedly joined to the dome flange and extend radially through respective ones of the mounting holes without interference therewith for allowing unrestrained thermal movement between the heat shield and the dome while supporting the heat shield against axial pressure loads thereon. In a preferred embodiment, the dome assembly includes three domes having respective ones of the heat shield, and respective baffles are spaced from the heat shields for providing impingement cooling thereof.

Halila, Ely E.↗

The structure of jet turbulence producing jet noise.

Measurements are presented that characterize the structure of the jet in both the core and the surrounding annular mixing region. Experiments were carried out in a 1.5-inch diameter subsonic jet at Mach numbers of 0.3, 0.5, and 0.7. The growth of pressure fluctuations within the core from the jet outlet to the end of the jet core was traced through the examination of spectral results. The spectra in the jet core exhibited a peak whose frequency scaled with the jet velocity and the jet diameter which is related to a characteristic dimension of the mixing process. A digital data reduction program was used to calculate the auto- and cross-correlations of axial velocity fluctuations. In the core the cross-correlations were nearly constant in the space-time plane indicating a traveling pressure wave, while in the annular mixing region the cross-correlations exhibited the usual decay in the space-time plane characteristic of convected turbulence.

Wooldridge, C. E.↗

Device for installing rocket engines

A device for installing rocket engines is reported that is supported at a cant relative to vertical by an axially extensible, tiltable pedestal. A lifting platform supports the rocket engine at its thrust chamber exit, including a mount having a concentric base characterized by a concave bearing surface, a plurality of uniformly spaced legs extended radially from the base, and an annular receiver coaxially aligned with the base and affixed to the distal ends of said legs for receiving the thrust chamber exit. The lifting platform rests on a seat concentrically related to the pedestal and affixed to an extended end portion thereof having a convex bearing surface mated in sliding engagement with the concave bearing surface of the annular base for accommodating a rocking motion of the platform.

George, T. R., Jr.↗

Simple, low-profile, circularly polarized arrays

A low-profile, circularly polarized antenna can be made using an annular sector of strip conductor parallel to a closely spaced ground plane. This antenna has a very wide impedance bandwidth and is particularly well suited for use in series-fed arrays. Control of the excitation coefficients can be accomplished by a simple variation in the geometry of each element. Interconnection of the elements has been realized both in coaxial cable and in microstrip. Axial ratios less than 1 dB in the broadside direction are easily obtainable.

Mayes, Paul↗

Design of a direct nuclear propulsion system for a resupply mission to Phobos

For a long-term mission in space, a propulsion system with a high specific impulse and low mass must be designed. The system must also be safe in terms of human lives and must be cost efficient to a degree. The main focus is to design a direct nuclear propulsion system for a resupply mission to Phobos from an orbiting Earth space station and return. The design considered is an annular, packed particle bed nuclear reactor with hydrogen used as the reflector, moderator, coolant, and propellant. The use of hydrogen in all these areas helps reduce the total mass, since the amount of hydrogen required is only that needed for propulsion. The mass of hydrogen required for propulsion is reduced by using a direct nuclear propulsion system with a high specific impulse relative to a hydrogen oxygen system. Certain calculations were not looked at in great detail. This included the aerospace details of the mission. Most of the numbers for this section were found in tables and taken to be correct without extensive calculations. The main objective of the project was to study the thermohydraulic and neutronic aspects of the reactor.

Frymire, R.↗