SEARCH · Search NASA

Results for “AeroAcoustics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

All sources NASA NTRS DOE OSTI

NASA NTRS1983

Aeroacoustic computation of cylinder wake flow

Sound generation by uniform flow over a cylinder at the Reynolds number of 200 is calculated. The incompressible, time dependent flow field is first computed by standard computational fluid dynamics techniques using a stream function/vorticity formulation. The sound radiation is then obtained by integrating over the flow field with the Coriolis acceleration as the source term and a low frequency Green's function technique. Time histories, spectra, and directivity of the radiated sound are obtained. Comparisons with experimental data, where possible, indicate the feasibility of this computational aeroacoustics approach.

Hardin, J. C.↗

NASA NTRS1983

The influence of inlet design on the aeroacoustic performance of a JT15D turbofan engine as measured in the NASA-Ames 40 x 80 foot wind tunnel

The influence of inlet design on the aeroacoustic performance of a JT15D turbofan engine was investigated in the NASA-Ames 40 x 80 ft wind tunnel. Four inlet designs representative of those found in commercial service were evaluated at a forward velocity of 80 kn. The inlet designs considered were selected to evaluate the importance of circumferential static pressure distortion (SPD) for a diffusing sound suppressing inlet and throat Mach number (Mth) for a hardwall inlet on the acoustic characteristics of the JT15D engine. Several speed points were studied simulating the operating conditions spanning approach to take-off. Results demonstrated that the dependency of the forward radiated noise on inlet aerodynamic design parameters was significant (about 5 dB) for the range of SPD (0.1-3.0%) and Mth (0.3-0.6) tested. The performance of the bulk absorber acoustic treatment used in the diffusing sound suppressing inlet is also discussed.

Holm, R. G.↗

NASA NTRS1983

Aeroacoustics of supersonic porous plug-nozzle flows

The effects of porosity on attenuation of noise from short plug-nozzle flows have been studied. Porosity of 10 percent distributed over the whole surface and porosity of 4 percent distributed over the middle-third surface of the conical plug have been investigated. The porosity results in favorable modifications of the repetitive shock structures as revealed by the shadowgraphs of the flow. The acoustic data indicate a reduction of noise intensity levels up to 4 dB for the porous plugs as compared to the solid concial plug. The locally distributed holes (4 percent porosity) are found to give aeroacoustic performance comparable to those with holes distributed over the whole surface (10 percent porosity). Also, the solid conical plug-nozzle is noted to yield noise reductions up to 9 dB when compared to the conical convergent plug-nozzle. A proposed mechanism of shock modification in porous plug-nozzle. A supported by shadowgraphic records.

Dosanjh, D. S.↗

NASA NTRS1983

An aeroacoustic model for high-speed, unsteady blade-vortex interaction

A three-dimensional aeroacoustic model is developed to predict the sound pulse radiated by the passage of a helicopter blade over a potential vortex. The linearized analysis assumes that either the blade-vortex separation is small or that the blade-tip Mach number is close to 1, or both, so that an acoustically noncompact situation exists. The three-dimensional blade loading due to blade-vortex interaction is constructed through a spanwise superposition of two-dimensional solutions with strength linearly increasing from hub to tip. Such a loading overestimates somewhat the strength of tip region dipoles in the acoustic calculation that follows. The final expression for the predicted far-field signature is obtained in closed form, and thus permits a relatively inexpensive calculation of the directivity of peak acoustic pressures in three dimensions.

Martinez, R.↗

NASA NTRS1984

Aeroacoustic interaction of a distributed vortex with a lifting Joukowski airfoil

A first principles computational aeroacoustics calculation of the flow and noise fields produced by the interaction of a distributed vortex with a lifting Joukowski airfoil is accomplished at the Reynolds number of 200. The case considered is that where the circulations of the vortex and the airfoil are of opposite sign, corresponding to blade vortex interaction on the retreating side of a single helicopter rotor. The results show that the flow is unsteady, even in the absence of the incoming vortex, resulting in trailing edge noise generation. After the vortex is input, it initially experiences a quite rapid apparent diffusion rate produced by stretching in the airfoil velocity gradients. Consideration of the effects of finite vortex size and viscosity causes the noise radiation during the encounter to be much less impulsive than predicted by previous analyses.

Hardin, J. C.↗

NASA NTRS1984

A correlation of scale model and flight aeroacoustic data for the Space Shuttle vehicle

A correlation is presented between aeroacoustic data acquired in the early Space Shuttle flights and in the various scale model tests from which the Shuttle vibroacoustic design environments were derived. These are the external acoustic data on the vehicle elements at liftoff, during the transonic and maximum dynamic pressure period of ascent flight, and during spent SRB reentry. The maximum external acoustic environment on the Shuttle elements in a given 1/3-octave frequency band comes from one of these critical flight regimes. The data correlation is seen to be good, testifying to adequate scale model measurement and test techniques. Some of the more salient features of the scale model test programs are described.

Dougherty, N. S.↗

NASA NTRS1986

Computational aeroacoustics - Present status and future promise

The field of computational aeroacoustics (CAA), in which sound generation by unsteady flows is calculated from first principles, has recently emerged as a viable discipline. This paper describes one CAA technique which has been validated for low Mach number, low Reynolds number, two-dimensional flows. Results of its application to geometries producing both dipole and quadrupole type sound sources are presented along with theoretical and experimental comparisons. In addition, the future promise of this and other CAA techniques in removing the present limitations is evaluated.

Hardin, J. C.↗

NASA NTRS1987

Comments on the aeroacoustics of helicopter rotors

Some techniques and procedures used in rotor aeroacoustics are examined. The advantages and disadvantages of using the acoustic analogy for noise prediction of helicopter rotors are discussed. The time domain and frequency domain approaches to rotor noise predictions are described. Consideration is given to steady and unsteady thickness noise, loading noise, and quadrupole noise.

Farassat, F.↗

NASA NTRS1988

Aeroacoustic research programs at the Army Aviation Research and Technology Activity

The Army rotorcraft aeroacoustic programs are reviewed, highlighting the theoretical and experimental progress made by Army researchers in the physical understanding of helicopter impulsive noise. The two impulsive noise sources addressed over this past decade are high-speed impulsive noise and blade-vortex interaction noise, both of which have had and will continue to have an increasing influence on Army rotorcraft design and operations. The advancements discussed are in the areas of in-flight data acquisition techniques, small-scale-model tests in wind tunnels, holographic interferometry/tomographic techniques, and the expanding capabilities of computational fluid dynamics in rotorcraft acoustic problems. Current theoretical prediction methods are compared with experimental data, and parameters that govern model scaling are established. The very successful cooperative efforts between the Army, NASA, and industry are also addressed

Yu, Yung H.↗

NASA NTRS1987

High-intensity tone generation by aeroacoustic sources

An experimental investigation has been carried out on the production of high-intensity tones by axisymmetric ring cavities. Maximum sound production occurs during an acoustic resonance at Strouhal numbers, which depend only on the local flow velocity independent of cavity location. Values of sound pressure of about 115 dB at 1-m distance can be generated by axisymmetric ring cavities on projectiles moving at a relatively low flight speed equal to 70 m/s. Frequencies in the audible range up to several kilohertz can be generated aeroacoustically. A simple analytical model has been developed to explain the experimental observations.

Shakkottai, P.↗

NASA NTRS1988

The role of unsteady aerodynamics in aeroacoustics

The role of acoustics and unsteady aerodynamics research in understanding the fundamental physics of time-dependent fluid phenomena is reviewed. The key issues are illustrated by considering the sound radiation of turbulent jets and the aeroacoustics of rotating bodies such as helicopter rotors. The importance of computational methods as a link between aerodynamics and acoustics is also discussed. It is noted that where acoustic analogy techniques are sufficiently accurate, unsteady aerodynamics can be used for acoustic prediction. In supersonic problems where acoustics and aerodynamics are coupled, an integrated nonlinear analysis can provide an accurate problem solution.

Pao, S. Paul↗

NASA NTRS1988

Measurement of sound emitted by flying projectiles with aeroacoustic sources

Training projectiles with axisymmetric ring cavities that produce intense tones in an airstream were shot in a straight-line trajectory. A ground-based microphone was used to obtain the angular distribution of sound intensity produced from the flying projectile. Data reduction required calculation of Doppler and attenuation factors. Also, the directional sensitivity of the ground-mounted microphone was measured and used in the data reduction. A rapid angular variation of sound intensity produced from the projectile was found that can be used to plot an intensity contour map on the ground. A full-scale field test confirmed the validity of the aeroacoustic concept of producing a relatively intense whistle from the projectile, and the usefulness of short-range flight tests that yield acoustic data free of uncertainties associated with diffraction, reflection, and refraction at jet boundaries in free-jet tests.

Cho, Y. I.↗

NASA NTRS1989

High resolution flow field prediction for tail rotor aeroacoustics

The prediction of tail rotor noise due to the impingement of the main rotor wake poses a significant challenge to current analysis methods in rotorcraft aeroacoustics. This paper describes the development of a new treatment of the tail rotor aerodynamic environment that permits highly accurate resolution of the incident flow field with modest computational effort relative to alternative models. The new approach incorporates an advanced full-span free wake model of the main rotor in a scheme which reconstructs high-resolution flow solutions from preliminary, computationally inexpensive simulations with coarse resolution. The heart of the approach is a novel method for using local velocity correction terms to capture the steep velocity gradients characteristic of the vortex-dominated incident flow. Sample calculations have been undertaken to examine the principal types of interactions between the tail rotor and the main rotor wake and to examine the performance of the new method. The results of these sample problems confirm the success of this approach in capturing the high-resolution flows necessary for analysis of rotor-wake/rotor interactions with dramatically reduced computational cost. Computations of radiated sound are also carried out that explore the role of various portions of the main rotor wake in generating tail rotor noise.

Quackenbush, Todd R.↗

NASA NTRS1989

Tilt rotor aircraft aeroacoustics

This paper studies the state of knowledge and the needed improvement in noise methodology and measurements for tilt rotor aircraft. Similarities and differences between tilt rotor aeroacoustic conditions and helicopter and propeller experience are identified. A discussion of the possible principal noise mechanisms throughout the flight envelope shows a need for further experimental and analytical investigations to develop an adequate understanding of the important sources and influencing factors. Existing experimental data from flight tests suggest terminal area noise reduction by operating within certain portions of the conversion flight envelope. Prediction methods are found to provide approximate indications only for low frequency harmonic and broadband noise for several of the tilt rotor's operating conditions. The acoustic effects of the hover case 'fountain' flow are pronounced and need further research. Impulsive noise and high frequency harmonic noise remain problems, as on helicopters, pending major improvements in wake, unsteady aerodynamics, and acoustics methodology.

George, Albert R.↗

NASA NTRS1991

Unified Aeroacoustics Analysis for High Speed Turboprop Aerodynamics and Noise: Development of Theory for Blade Loading, Wakes, and Noise - Volume 1

A unified theory for the aerodynamics and noise of advanced turboprops are presented. Aerodynamic topics include calculation of performance, blade load distribution, and non-uniform wake flow fields. Blade loading can be steady or unsteady due to fixed distortion, counter-rotating wakes, or blade vibration. The aerodynamic theory is based on the pressure potential method and is therefore basically linear. However, nonlinear effects associated with finite axial induction and blade vortex flow are included via approximate methods. Acoustic topics include radiation of noise caused by blade thickness, steady loading (including vortex lift), and unsteady loading. Shielding of the fuselage by its boundary layer and the wing are treated in separate analyses that are compatible but not integrated with the aeroacoustic theory for rotating blades.

Hanson, D. B.↗

NASA NTRS1990

Large-scale aeroacoustic research feasibility and conceptual design of test-section inserts for the Ames 80- by 120-foot wind tunnel

An engineering feasibility study was made of aeroacoustic inserts designed for large-scale acoustic research on aircraft models in the 80 by 120 foot Wind Tunnel at NASA Ames Research Center. The advantages and disadvantages of likely designs were analyzed. Results indicate that the required maximum airspeed leads to the design of a particular insert. Using goals of 200, 150, and 100 knots airspeed, the analysis indicated a 30 x 60 ft open-jet test section, a 40 x 80 ft open jet test section, and a 70 x 100 ft closed test section with enhanced wall lining, respectively. The open-jet inserts would be composed of a nozzle, collector, diffuser, and acoutic wedges incorporated in the existing 80 x 120 test section. The closed test section would be composed of approximately 5 ft acoustic wedges covered by a porous plate attached to the test section walls of the existing 80 x 120. All designs would require a double row of acoustic vanes between the test section and fan drive to attenuate fan noise and, in the case of the open-jet designs, to control flow separation at the diffuser downstream end. The inserts would allow virtually anechoic acoustic studies of large helicopter models, jets, and V/STOL aircraft models in simulated flight. Model scale studies would be necessary to optimize the aerodynamic and acoustic performance of any of the designs. In all designs studied, the existing structure would have to be reinforced. Successful development of acoustically transparent walls, though not strictly necessary to the project, would lead to a porous-wall test section that could be substituted for any of the open-jet designs, and thereby eliminate many aerodynamic and acoustic problems characteristic of open-jet shear layers. The larger size of the facility would make installation and removal of the insert components difficult. Consequently, scheduling of the existing 80 x 120 aerodynamic test section and scheduling of the open-jet test section would likely be made on an annual or longer basis. The enhanced wall-lining insert would likely be permanent. Although the modifications are technically feasible, the economic practicality of the project was not evaluated.

Soderman, Paul T.↗

NASA NTRS1991

Unified aeroacoustics analysis for high speed turboprop aerodynamics and noise. Volume 3: Application of theory for blade loading, wakes, noise, and wing shielding

Results of the program for the generation of a computer prediction code for noise of advanced single rotation, turboprops (prop-fans) such as the SR3 model are presented. The code is based on a linearized theory developed at Hamilton Standard in which aerodynamics and acoustics are treated as a unified process. Both steady and unsteady blade loading are treated. Capabilities include prediction of steady airload distributions and associated aerodynamic performance, unsteady blade pressure response to gust interaction or blade vibration, noise fields associated with thickness and steady and unsteady loading, and wake velocity fields associated with steady loading. The code was developed on the Hamilton Standard IBM computer and has now been installed on the Cray XMP at NASA-Lewis. The work had its genesis in the frequency domain acoustic theory developed at Hamilton Standard in the late 1970s. It was found that the method used for near field noise predictions could be adapted as a lifting surface theory for aerodynamic work via the pressure potential technique that was used for both wings and ducted turbomachinery. In the first realization of the theory for propellers, the blade loading was represented in a quasi-vortex lattice form. This was upgraded to true lifting surface loading. Originally, it was believed that a purely linear approach for both aerodynamics and noise would be adequate. However, two sources of nonlinearity in the steady aerodynamics became apparent and were found to be a significant factor at takeoff conditions. The first is related to the fact that the steady axial induced velocity may be of the same order of magnitude as the flight speed and the second is the formation of leading edge vortices which increases lift and redistribute loading. Discovery and properties of prop-fan leading edge vortices were reported in two papers. The Unified AeroAcoustic Program (UAAP) capabilites are demonstrated and the theory verified by comparison with the predictions with data from tests at NASA-Lewis. Steady aerodyanmic performance, unsteady blade loading, wakes, noise, and wing and boundary layer shielding are examined.

Hanson, D. B.↗

NASA NTRS1990

Aeroacoustic environment of an advanced STOVL aircraft in hover

The near-field aeroacoustic environment of a 6.02 pct scale advanced short takeoff and vertical landing aircraft is investigated in proximity to a simulated ground plane. The screech and impingement-tone characteristics of twin supersonic round and rectangular plumes are shown to be highly dependent on nozzle geometry and height above the ground plane. Shadowgraph and laser-sheet flow visualization are used to clarify the flowfield mechanisms responsible for time-dependent loads due to screech, impingement tones, and unsteady impingement of the upwash on the fuselage undersurface. Detailed dynamic pressure measurements from an array of transducers on the fuselage confirms that fountain impingement is responsible for the greatest unsteady loading.

Wlezien, Richard W.↗