Search NASA⌕ Search

SEARCH · Search NASA

Results for “Aerocapture”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Optimal Angle of Attack Control for Aerocapture Maneuvers

Recent investigations of aerocapture maneuvers have considered direct force control as a promising alternative to bank angle control. By modulating the angle of attack and sideslip angle independently, the longitudinal and lateral channels can be decoupled and thus solved separately. However, the optimal angle of attack profile for minimizing post-atmospheric propellant expenditure was previously unknown. This research applies principles of optimal control theory to numerically solve for the optimal angle of attack profile for control of the longitudinal channel. Direct methods are first employed to discretize the angle of attack profile and show that an optimal solution follows a nearly bang-bang (full lift up then full lift down) structure under a variety of conditions along the flight path angle corridor. To corroborate these results, indirect methods were also applied to scope the Optimal Control Problem (OCP) as a Two Point Boundary Value Problem (2P-BVP) which could then be solved numerically. The indirect optimization results aligned closely with the direct results, providing further evidence that a bang-bang structure provides a good approximation for the optimal angle of attack profile for aerocapture maneuvers using direct force control.

aerocapture↗
NASA NTRS2023

Computational Aerothermal Modeling and Simulation of Hypersonic, Low-density Flows for the ADEPT Drag Modulated Aerocapture Mission

NASA Ames Entry Systems and Technology Division has been leading development and testing of the Adaptable, Deployable, Entry and Placement Technology (ADEPT). A teaming partnership with JPL has been established to study and develop a compelling application of the ADEPT mechanically deployable hypersonic decelerator as part of the Venus Drag Modulated Aerocapture (VDMA) JPL R&TD effort. The primary work of this activity is to develop a design tool for the ADEPT drag skirt (e.g. a CFD-anchored CBAERO model) that enables rapid estimation of aerothermal environments for a range of candidate trajectories. This capability will enable rapid feasibility trades and design assessments for early stage mission concept evaluation for ADEPT Drag Modulated Aerocapture applications. Results of using TPSizer provided an ADEPT carbon fabric design thickness of the required number of fabric layers needed for predicted aerothermal environments and still have sufficient fabric remaining for overall vehicle integrity. This resulted in aerothermal design closure of the ADEPT drag skirt. In addition, the similar methodology for Venus DMA was used to assess a similar DMA operation at Earth as part of a possible Technology Demonstration Mission (TDM) for ADEPT DMA. This analysis showed that there is a close similarity of design approaches for an Earth DMA TDM that would be applicable to Venus DMA mission designs.

Drag Modulated Aerocapture↗
NASA NTRSDate not supplied

Thermal Protection System Design of Aerocapture Systems for Uranus Orbiters

The National Academies Planetary Science and Astrobiology Decadal Survey recently identified Uranus and Neptune - the Ice Giants - as the priority destinations for science. A mission to Uranus, the highest priority destination due to proximity to Earth, is viable with existing launch vehicle providers during launch windows starting in 2031. However, a nominal interplanetary trajectory (between 12 and 15 years) would still necessitate more than half the initial launch mass in propellant to achieve orbital insertion. Aerocapture, a method of orbital control that directs aerodynamic forces generated on a vehicle by the planet's atmosphere, allows mission designers to achieve the desired orbital state while saving time to the final destination and increasing the available mass for the science payload. Achieving orbital insertion via aerocapture requires novel algorithms for Guidance, Navigation and Control, and mass-efficient Thermal Protection Systems (TPS) performing in an atmosphere unlike any other NASA has flown through. Multiple TPS in NASA's repertoire are suitable for the unique aerothermal environment on the forebody, and the results of predicted sizing and challenges in implementation are discussed below. Results for aftbody TPS made by NASA as well as commercial vendors are discussed, along with the discussion of alternative solutions that may save time, reduce complexity, and increase mass-efficiency for the recommended Uranus Orbiter and Probe mission.

Uranus↗
NASA NTRSDate not supplied

Design Considerations for Aerocapture Delivery of Uranus Orbiter and Probe

This paper presents an aerocapture system design for delivering the Uranus Orbiter and Probe (UOP) subsystems to their science orbit using the Mars Science Laboratory architecture. A packaging and integration scheme are presented for UOP subsystems, with careful consideration of large components required for outer planet science missions (RTG power generation, RF communications). The implication of packaging multiple RTG’s inside an aeroshell during a multiple year cruise phase will be explained, with possible thermal design solutions to mitigate RTG waste heat analyzed. Mass properties and margins for the system are discussed and an overall mass risk assessment is presented for the entry system and total flight system at launch. Alternative vehicle configurations are explored to include multiple probes and enable science objectives during transit to Uranus. Aerocapture mass savings when compared to the baseline UOP design are presented.

Aerocapture↗
NASA NTRSDate not supplied

Impact of Magnetohydrodynamic (MHD) Induced Drag on High Ballistic Coefficient Aerocapture at Neptune

This paper presents analyses illustrating the benefits of magnetohydrodynamic (MHD) drag force control for a capsule performing aerocapture at Neptune relative to the same capsule utilizing conventional aerodynamic-only control across a range of design and flight conditions. MHD technology utilizes an onboard mag-net to create a magnetic field that interacts with the ionized plasma surrounding the capsule at hypersonic velocities, thus creating an electron current and inducing a Lorentz force used to increase capsule drag. The study assumes a 4.57-meterMars Science Laboratory (MSL) 70-degree sphere-cone capsule aerodynamic shape arrives hyperbolically at Neptune and aerocaptures into a synchronous Tri-ton orbit (3986 km x 430,000 km orbit inclined 157 degrees) that offers repeated flyby opportunities. Hyperbolic arrival velocity and the capsule entry mass (i.e., ballistic coefficient) are varied over a wide range of values to study the impact of these variables on key flight performance and sizing parameters. Results show reduced heat rates, heat loads, and thermal protection system mass for MHD cases at all conditions, with the benefit of MHD relative to conventional aerodynamic-only options increasing as ballistic coefficient increases, suggesting the payoff for MHD is significantly better for high-mass entry system design concepts with high ballistic coefficients.

Entry Descent and Landing↗
NASA NTRS1980

Design integration of aerocapture and aeromaneuver vehicles for a Mars sample return mission

The concept of using an aerocapture vehicle for Mars and other planetary missions is a technology that yields significant fuel savings. This concept uses the planet's atmosphere to dissipate excess velocity of the entry vehicle allowing it to go into orbit. A conceptual design integration study of two configurations of aerocapture vehicles which can make an aerodynamically controlled entry has been made. The first configuration contains the existing Viking type Lander and an Orbiter. The second spacecraft is more general in payload and could be used to place an Orbiter and a Lander on other planets with a single aeroshell.

Hassett, R. J.↗
NASA NTRS1982

Aerocapture - Guidance, navigation, and control

Aerocapture is a concept for inserting a spacecraft into orbit about a target planet. The energy required for orbit insertion is obtained from natural resources present at or near the target body, thereby reducing the amount of propellant which must be carried onboard. Specifically, the transfer from a hyperbolic flyby trajectory to a desired bound orbit is effected by aerodynamic lift and drag forces acting on the spacecraft during controlled flight through the atmosphere of either the target planet or a nearby satellite. A survey is provided of the trajectory guidance, navigation, and control aspects of aerocapture, and a summary is given of the results of a number of preliminary studies concerning certain of these aspects. The investigation has additional significance in connection with the current interest in aeroassisted orbital transfer vehicles, which may be used in conjunction with the Space Shuttle.

Mease, K. D.↗
NASA NTRS1989

An onboard navigation system which fulfills Mars aerocapture guidance requirements

The development of a candidate autonomous onboard Mars approach navigation scheme capable of supporting aerocapture into Mars orbit is discussed. An aerocapture guidance and navigation system which can run independently of the preaerocapture navigation was used to define a preliminary set of accuracy requirements at entry interface. These requirements are used to evaluate the proposed preaerocapture navigation scheme. This scheme uses optical sightings on Deimos with a star tracker and an inertial measurement unit for instrumentation as a source for navigation nformation. Preliminary results suggest that the approach will adequately support aerocaputre into Mars orbit.

Brand, Timothy J.↗
NASA NTRS1994

Comment on 'Guidance for an Aerocapture Maneuver

It is stated that the aerodynamic forces on the vehicle being aerocaptured are controlled by "altering the angle of attack" and thereby controlling the lift coefficient. Furthermore, the resulting variation of drag coefficient with angle of attack was ignored. The purpose of this Comment is to point out that an aerodynamic control method that is much more effective than the pitch modulation has been studied and utilized during entries for many years. During aerocapture, it is desirable to have a large range of lift coefficients available, while keeping the vehicle's ballistic coefficients constant. This is accomplished by modulating the vehicle's bank angle, i.e., by rolling the vehicle about its velocity vector. By this method, the angle of attack can be held constant (at the trim angle, if desired), and the C(sub D) and the ballistic coefficient remain constant. Furthermore, the vertical component of the normal force vector (essentially the lift) can be varied over its entire range, from maximum positive to maximum negative values. Reaction controls, rather than aerodynamic ones, are usually utilized to change the bank angle of the vehicle, thus requiring the use of fuel. However, the fuel expenditure that is required to change the bank angle is far less than the amount that would have to be used to continuously hold the vehicle at pitch angles that differ significantly from its trim angle of attack. Also, it has been shown that bank angle modulation to vary the lift can enlarge the entry corridor by increasing the entry angle for the undershoot boundary, where both the heating rate and deceleration reach a maximum. Finally, the crew's deceleration tolerance can be increased somewhat when the bank angle is varied, as opposed to the pitch angle. For bank modulation, the deceleration force vector can be kept at a constant angle with respect to the occupants whose tolerance to g loads is highest when the force is applied in a direction normal to the upper torso. The advantages of bank angle variation to modulate the lift vector were recognized long ago, and this method of control was used successfully on the Apollo command module during lunar return' and, more recently, for the Space Shuttle Orbiter.

Tauber, Michael E.↗
NASA NTRS2003

NASA Development of Aerocapture Technologies

Aeroassist technology development is a vital part of the NASA ln-Space Propulsion Program (ISP), which is managed by the NASA Headquarters Office of Space Science, and implemented by the Marshall Space Flight Center in Huntsville, Alabama. Aeroassist is the general term given to various techniques to maneuver a space vehicle within an atmosphere, using aerodynamic forces in lieu of propulsive fuel. Within the ISP, the current aeroassist technology development focus is aerocapture. The objective of the ISP Aerocapture Technology Project (ATP) is to develop technologies that can enable and/or benefit NASA science missions by significantly reducing cost, mass, and/or travel times. To accomplish this objective, the ATP identifies and prioritizes the most promising technologies using systems analysis, technology advancement and peer review, coupled with NASA Headquarters Office of Space Science target requirements. Plans are focused on developing mid-Technology Readiness Level (TRL) technologies to TRL 6 (ready for technology demonstration in space).

James, Bonnie↗
NASA NTRS2003

Aerocapture Technology Project Overview

Aerocapture technology development is one of the highest priority investments for the NASA In-Space Propulsion Program (ISP). The ISP is managed by the NASA Headquarters Office of Space Science, and implemented by the Marshall Space Flight Center in Huntsville, Alabama. The objective of the ISP Aerocapture Technology Project (ATP) is to develop technologies that can enable and/or benefit NASA science missions by significantly reducing cost, mass, and trip times. To accomplish this objective, the ATP identifies and prioritizes the most promising technologies using systems analysis, technology advancement and peer review, coupled with NASA Headquarters Office of Space Science target requirements. Efforts are focused on developing mid-Technology Readiness Level (TRL) technologies to systems-level spaceflight validation.

James, Bonnie↗
NASA NTRS2004

Angle-of-Attack-Modulated Terminal Point Control for Neptune Aerocapture

An aerocapture guidance algorithm based on a calculus of variations approach is developed, using angle of attack as the primary control variable. Bank angle is used as a secondary control to alleviate angle of attack extremes and to control inclination. The guidance equations are derived in detail. The controller has very small onboard computational requirements and is robust to atmospheric and aerodynamic dispersions. The algorithm is applied to aerocapture at Neptune. Three versions of the controller are considered with varying angle of attack authority. The three versions of the controller are evaluated using Monte Carlo simulations with expected dispersions.

Queen, Eric M.↗
NASA NTRS2004

Preliminary Convective-Radiative Heating Environments for a Neptune Aerocapture Mission

Convective and radiative heating environments have been computed for a three-dimensional ellipsled configuration which would perform an aerocapture maneuver at Neptune. This work was performed as part of a one-year Neptune aerocapture spacecraft systems study that also included analyses of trajectories, atmospheric modeling, aerodynamics, structural design, and other disciplines. Complementary heating analyses were conducted by separate teams using independent sets of aerothermodynamic modeling tools (i.e. Navier-Stokes and radiation transport codes). Environments were generated for a large 5.50 m length ellipsled and a small 2.88 m length ellipsled. Radiative heating was found to contribute up to 80% of the total heating rate at the ellipsled nose depending on the trajectory point. Good agreement between convective heating predictions from the two Navier-Stokes solvers was obtained. However, the radiation analysis revealed several uncertainties in the computational models employed in both sets of codes, as well as large differences between the predicted radiative heating rates.

Hollis, Brian R.↗
NASA NTRS2004

Saturn/Titan Rendezvous: A Solar-Sail Aerocapture Mission

A low-mass Titan orbiter is proposed that uses conservative or optimistic solar sails for all post-Earth-escape propulsion. After accelerating the probe onto a trans-Saturn trajectory, the sail is used parachute style for Saturn capture during a pass through Saturn's outer atmosphere. If the apoapsis of the Saturn-capture orbit is appropriate, the aerocapture maneuver can later be repeated at Titan so that the spacecraft becomes a satellite of Titan. An isodensity-atmosphere model is applied to screen aerocapture trajectories. Huygens/Cassini should greatly reduce uncertainties regarding the upper atmospheres of Saturn and Titan.

Matloff, Gregory L.↗
NASA NTRS2004

NASA Development of Aerocapture Technologies

Aeroassist technology development is a vital part of the NASA In-Space Propulsion Program (ISP), which is managed by the NASA Headquarters Office of Space Science, and implemented by the Marshall Space Flight Center in Huntsville, Alabama. Aeroassist is the general term given to various techniques to maneuver a space vehicle within an atmosphere, using aerodynamic forces in lieu of propulsive fuel. Within the ISP, the current aeroassist technology development focus is aerocapture. The objective of the ISP Aerocapture Technology Project (ATP) is to develop technologies that can enable and/or benefit NASA science missions by significantly reducing cost, mass, and/or travel times. To accomplish this objective, the ATP identifies and prioritizes the most promising technologies using systems analysis, technology advancement and peer review, coupled with NASA Headquarters Office of Space Science target requirements. Plans are focused on developing mid-Technology Readiness Level (TRL) technologies to TRL 6 (ready for technology demonstration in space).

James, Bonnie↗
NASA NTRS2010

Aerocapture Guidance and Performance at Mars for High-Mass Systems

The objective of this study is to understand the performance associated with using the aerocapture maneuver to slow high-mass systems from an Earth-approach trajectory into orbit around Mars. This work is done in conjunction with the Mars Entry Descent and Landing Systems Analysis (EDL-SA) task to explore candidate technologies necessary for development in order to land large-scale payloads on the surface of Mars. Among the technologies considered include hypersonic inflatable aerodynamic decelerators (HIADs) and rigid mid-lift to drag (L/D) aeroshells. Nominal aerocapture trajectories were developed for the mid-L/D aeroshell and two sizes of HIADs, and Monte Carlo analysis was completed to understand sensitivities to dispersions. Additionally, a study was completed in order to determine the size of the larger of the two HIADs which would maintain design constraints on peak heat rate and diameter. Results show that each of the three aeroshell designs studied is a viable option for landing high-mass payloads as none of the three exceed performance requirements.

Zumwalt, Carlie H.↗
NASA NTRS2020

Development of a Numeric Predictor-Corrector Aerocapture Guidance for Direct Force Control

Direct force control, where the angle of attack and sideslip angle are modulated, has been proposed as an alternative to bank angle control for aero-assist maneuvers. This paper reimplements the current state-of-the-art aerocapture guidance for bank angle control, Fully Numeric Predictor-corrector Aerocapture Guidance (FNPAG), for direct force control. The optimal control theory underlying the structure of FNPAG is shown to not be applicable to the direct force control approach. Several solution structures for the longitudinal channel are compared by simulating dispersed three-degree-of-freedom trajectories for a reference mission consisting of a low lift-to-drag vehicle and a highly elliptical, 1-sol target orbit around Mars. The equations of motion for the lateral channel are derived, and a controller is designed to target a specified orbital plane. Finally, a Monte Carlo is used to demonstrate the performance of the new guidance.

Matz, Daniel A.↗
NASA NTRS2021

Aerocapture Trajectories for Earth Orbit Technology Demonstration and Orbiter Science Missions at Venus, Earth, Mars, and Neptune

The use of aerocapture to provide the delta-V needed to capture a spacecraft into orbit can provide significant fuel savings compared to a propulsive orbit insertion. The aerocapture guidance method described in this paper uses drag modulation, which deploys a drag skirt in the atmosphere until the amount of delta-V needed to capture into the desired orbit is obtained, at which time the drag skirt is separated from the spacecraft. By modulating the time of drag skirt jettison, the vehicle can target a specific orbit apoapsis in the presence of uncertainties such as entry targeting errors and unknown atmospheric conditions.

Jadusingh, Matt↗