Search NASA⌕ Search

SEARCH · Search NASA

Results for “Airloads”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Unsteady airloading panel method for prop-fans

An unsteady, linear, compressible, three dimensional lifting surface panel method is presented for use with propellers and prop-fans. Both gust and blade vibration problems can be treated. Derivation of the theory is based on the acceleration potential method and can be considered a generalization of the analogous wing theory to include rotation and multiple blades. As with the wing methods, the integral equation is discretized and solved by matrix inversion. Sample calculations are use to explore the difference between 2D and 3D results and the significance of unsteadiness in angular inflow calculations for propellers. It is shown at the once-per-revolution frequency of propellers, that quasi-steady methods should be adequate. At the high frequencies of interest in noise analysis, 2D strip methods give adequate results away from blade tips. For flutter, frequencies lie in an intermediate range where a full 3D unsteady technique seems to be required.

Hanson, D. B.↗
NASA NTRS1990

Prediction of blade-vortex interaction noise using airloads generated by a finite-difference technique

The present numerical finite-difference scheme for helicopter blade-load prediction during realistic, self-generated three-dimensional blade-vortex interactions (BVI) derives the velocity field through a nonlinear superposition of the rotor flow-field yielded by the full potential rotor flow solver RFS2 for BVI, on the one hand, over the rotational vortex flow field computed with the Biot-Savart law. Despite the accurate prediction of the acoustic waveforms, peak amplitudes are found to have been persistently underpredicted. The inclusion of BVI noise source in the acoustic analysis significantly improved the perceived noise level-corrected tone prediction.

Tadghighi, Hormoz↗
NASA NTRS1956

Investigation of Vertical Drag and Periodic Airloads Acting on Flat Panels in a Rotor Slipstream

Tests have been conducted on the Langley helicopter test tower to determine the vertical drag and pressure distributions on flat panels mounted below a helicopter rotor. Calculations of the vertical drag by use of a strip-analysis procedure outlined in the paper and the assumption of a fully contracted wake agreed well with the experimental results over the range from 0.2 to 0.64 rotor radius beneath the plane of zero flapping. The pressure increase caused by the passage of the blade over the panel is a maximum at about the 0.8 radius spanwise station. At this station, the pressure decreases from 10 times the disk loading per blade at 0.05 radius beneath the rotor plane of zero flapping to one-half of the disk loading per blade at 0.64 radius beneath the plane of zero flapping.

LOADS - ROTATING WINGS↗
NASA NTRS2009

UH-60 Airloads Program Tutorial

From the fall of 1993 to late winter of 1994, NASA Ames and the U.S. Army flew a flight test program using a UH-60A helicopter with extensive instrumentation on the rotor and blades, including 242 pressure transducers. Over this period, approximately 30 flights were made, and data were obtained in level flight, maneuver, ascents, and descents. Coordinated acoustic measurements were obtained with a ground-acoustic array in cooperation with NASA Langley, and in-flight acoustic measurements with a YO-3A aircraft. NASA has sponsored the creation of a "tutorial' which covers the depth and breadth of the flight test program with a mixture of text and graphics. The primary purpose of this tutorial is to introduce the student to what is known about rotor aerodynamics based on the UH-60A measurements. The tutorial will also be useful to anyone interested in helicopters who would like to have more detailed knowledge about helicopter aerodynamics.

Bousman, William G.↗
NASA NTRS2011

Fundamental Aeronautics Program. Subsonic Rotary Wing Project: SRW Aeromechanics Overview/UH-60 Airloads Wind Tunnel Test Summary

Objectives: a) Advance the understanding of phenomena in aerodynamics, dynamics, and active control of rotorcraft. b) Develop and validate first-principles tools. c) Acquire data for tool validation from small and large-scale testing of existing and novel rotorcraft configurations. Recent Accomplishments include: (CFD) - Made significant improvements in structured and unstructured rotorcraft CFD methods (OVERFLOW and FUN3D). (Icing) - a) Continued development of high-fidelity icing analysis tools. b) Completed test of oscillating airfoil in Icing Research Tunnel (IRT). c) Developed plans and began detailed preparations for subscale rotor test in IRT.

Norman, Thomas R.↗
NASA NTRS2011

UH-60A Airloads Wind Tunnel Data Update

Presentation reviews (1) Background, (2)Efforts since February 2011, (2a)Database, (2b) PIV/Blade Displacement, (2c) Other activities, (3) Data availability and (4) Near-term plans.

Norman, Thomas R.↗
NASA NTRS1991

Unified aeroacoustics analysis for high speed turboprop aerodynamics and noise. Volume 4: Computer user's manual for UAAP turboprop aeroacoustic code

The Unified AeroAcoustic Program (UAAP) code calculates the airloads on a single rotation prop-fan, or propeller, and couples these airloads with an acoustic radiation theory, to provide estimates of near-field or far-field noise levels. The steady airloads can also be used to calculate the nonuniform velocity components in the propeller wake. The airloads are calculated using a three dimensional compressible panel method which considers the effects of thin, cambered, multiple blades which may be highly swept. These airloads may be either steady or unsteady. The acoustic model uses the blade thickness distribution and the steady or unsteady aerodynamic loads to calculate the acoustic radiation. The users manual for the UAAP code is divided into five sections: general code description; input description; output description; system description; and error codes. The user must have access to IMSL10 libraries (MATH and SFUN) for numerous calls made for Bessel functions and matrix inversion. For plotted output users must modify the dummy calls to plotting routines included in the code to system-specific calls appropriate to the user's installation.

Menthe, R. W.↗
NASA NTRS1983

In-flight load testing of advanced shuttle thermal protection systems

NASA Ames Research Center has conducted in-flight airload testing of some advanced thermal protection systems (TPS) at the Dryden Flight Research Center. The two flexible TPS materials tested, felt reusable surface insulation (FRSI) and advanced flexible reusable surface insulation (AFRSI), are currently certified for use on the Shuttle orbiter. The objectives of the flight tests were to evaluate the performance of FRSI and AFRSI at simulated launch airloads and to provide a data base for future advanced TPS flight tests. Five TPS configurations were evaluated in a flow field which was representative of relatively flat areas without secondary flows. The TPS materials were placed on a fin, the Flight Test fixture (FTF), that is attached to the underside of the fuselage of an F-104 aircraft. This paper describes the test approach and techniques used and presents the results of the advanced TPS flight test. There were no failures noted during post-flight inspections of the TPS materials which were exposed to airloads 40 percent higher than the design launch airloads.

Trujillo, B. M.↗
NASA NTRS1983

In-flight load testing of advanced thermal protection systems

NASA Ames Research Center has conducted in-flight airload testing of some advanced thermal protection systems (TPS) at the Dryden Flight Research Center. The two flexible TPS materials tested, felt reusable surface insulation (FRSI) and advanced flexible reusable surface insulation (AFRSI), are currently certified for use on the Shuttle orbiter. The objectives of the flight tests were to evaluate the performance of FRSI and AFRSI at simulated launch airloads and to provide a data base for future advanced TPS flight tests. Five TPS configurations were evaluated in a flow field which was representative of relatively flat areas without secondary flows. The TPS materials were placed on a fin, the Flight Test Fixture (FTF), that is attached to the underside of the fuselage of an F-104 aircraft. This paper describes the test approach and techniques used and presents the results of the advanced TPS flight test. There were no failures noted during post-flight inspections of the TPS materials which were exposed to airloads 40 percent higher than the design launch airloads.

Trujillo, B. M.↗
NASA NTRS1993

Dynamic stall of an oscillating wing. Part 1: Evaluation of turbulence models

Unsteady flowfields of a two-dimensional oscillating wing are calculated using an implicit, finite-difference, Navier-Stokes numerical scheme using five widely used turbulence models. The objective of this study is to identify an appropriate turbulence model for accurate simulation of three-dimensional dynamic stall. Three unsteady flow conditions corresponding to attached flow, light-stall, and deep-stall of an oscillating wing experiment were chosen as test cases for computations. Results of unsteady airload hysteresis curves, harmonics of unsteady pressures, and instantaneous flow pictures are presented. Comparison of unsteady airloads with experiment show that all models are deficient in some sense and not a single model predicts all airloads consistently and in agreement with experiment for all flow conditions. For the attached flow condition, the Renormalization Group Theory (RNG), the Johnoson-King (J-K), and the Spalart-Allmaras (S-A) models have better performance. The Baldwin-Lomax (B-L) and the Baldwin-Barth (B-B) models fair poorly. At the light-stall condition, the results for the RNG, the J-K, and S-A models are in agreement with experiment for the upstroke but they all over predict the separation shown by the experiment and therefore have bigger hysteresis loops than experimental results. The B-B model results are also in good agreement for upstroke but have poor lift hysteresis for downstroke. It has superior drag and pitching-moment predictions. For deep-stall conditions, the airloads for the RNG, the B -B, and the S-A models have fair agreement with experiment, but the B-B model performed better at the extreme deep-stall condition. Overall, the RNG model provides significant improvement over the B-L model in all flow regimes with no additional computational cost. The Baldwin-Barth model is the most expensive of the models considered here, costing about 2.5 times that of the Baldwin-Lomax model. Finally, a brief discussion of the effects of grid density, time-step size, and numerical dissipation on the unsteady solutions are also presented.

Srinivasan, G. R.↗
NASA NTRS1974

The Vortex Lattice Method for the Rotor-Vortex Interaction Problem

The rotor blade-vortex interaction problem and the resulting impulsive airloads which generate undesirable noise levels are discussed. A numerical lifting surface method to predict unsteady aerodynamic forces induced on a finite aspect ratio rectangular wing by a straight, free vortex placed at an arbitrary angle in a subsonic incompressible free stream is developed first. Using a rigid wake assumption, the wake vortices are assumed to move downsteam with the free steam velocity. Unsteady load distributions are obtained which compare favorably with the results of planar lifting surface theory. The vortex lattice method has been extended to a single bladed rotor operating at high advance ratios and encountering a free vortex from a fixed wing upstream of the rotor. The predicted unsteady load distributions on the model rotor blade are generally in agreement with the experimental results. This method has also been extended to full scale rotor flight cases in which vortex induced loads near the tip of a rotor blade were indicated. In both the model and the full scale rotor blade airload calculations a flat planar wake was assumed which is a good approximation at large advance ratios because the downwash is small in comparison to the free stream at large advance ratios. The large fluctuations in the measured airloads near the tip of the rotor blade on the advance side is predicted closely by the vortex lattice method.

Padakannaya, R.↗
NASA NTRS1974

Lifting-surface theory for a semi-infinite wing in oblique gust

An unsteady lifting-surface theory is developed for the calculation of the airload on a semi-infinite-span thin wing in a compressible flow due to interaction with an oblique gust. By using the solutions obtained for a two-dimensional wing, the problem is formulated so that the unknown is taken to be the difference between the airload on the semi-infinite wing and that on a two-dimensional wing under the same gust conditions. Since this airload difference is nonzero only near the wing tip, the control points need be distributed in the tip region only; this significantly simplifies the numerical procedure. Results are presented for a wing with rectangular tip. The implication for noise and unsteady loads due to blade-vortex interaction for helicopter rotors is discussed.

Chu, S.↗
NASA NTRS1977

Unsteady aerodynamic modeling and active aeroelastic control

Unsteady aerodynamic modeling techniques are developed and applied to the study of active control of elastic vehicles. The problem of active control of a supercritical flutter mode poses a definite design goal stability, and is treated in detail. The transfer functions relating the arbitrary airfoil motions to the airloads are derived from the Laplace transforms of the linearized airload expressions for incompressible two dimensional flow. The transfer function relating the motions to the circulatory part of these loads is recognized as the Theodorsen function extended to complex values of reduced frequency, and is termed the generalized Theodorsen function. Inversion of the Laplace transforms yields exact transient airloads and airfoil motions. Exact root loci of aeroelastic modes are calculated, providing quantitative information regarding subcritical and supercritical flutter conditions.

Edwards, J. W.↗
NASA NTRS1978

Helicopter external noise prediction and correlation with flight test

Mathematical analysis procedures for predicting the main and tail rotor rotational and broadband noise are presented. The aerodynamic and acoustical data from Operational Loads Survey (OLS) flight program are used for validating the analysis and noise prediction methodology. For the long method of rotational noise prediction, the spanwise, chordwise, and azimuthwise airloading is used. In the short method, the airloads are assumed to be concentrated at a single spanwise station and for higher harmonics an airloading harmonic exponent of 2.0 is assumed. For the same flight condition, the predictions from long and short methods of rotational noise prediction are compared with the flight test results. The short method correlates as well or better than the long method.

Gupta, B. P.↗
NASA NTRS1979

Unsteady flow model for circulation-control airfoils

An analysis and a numerical lifting surface method are developed for predicting the unsteady airloads on two-dimensional circulation control airfoils in incompressible flow. The analysis and the computer program are validated by correlating the computed unsteady airloads with test data and also with other theoretical solutions. Additionally, a mathematical model for predicting the bending-torsion flutter of a two-dimensional airfoil (a reference section of a wing or rotor blade) and a computer program using an iterative scheme are developed. The flutter program has a provision for using the CC airfoil airloads program or the Theodorsen hard flap solution to compute the unsteady lift and moment used in the flutter equations. The adopted mathematical model and the iterative scheme are used to perform a flutter analysis of a typical CC rotor blade reference section. The program seems to work well within the basic assumption of the incompressible flow.

Rao, B. M.↗