Search NASA⌕ Search

SEARCH · Search NASA

Results for “AlGaAs”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Low-noise behavior of InGaAs quantum-well-structured modulation-doped FET's from 10 to the -2nd to 10 to the 8 Hz

Equivalent gate noise voltage spectra of 1-micron gate-length modulation-doped FET's with pseudomorphic InGaAs quantum-well structure have been measured for the frequency range of 0.01 Hz to 100 MHz and commpared with the noise spectra of conventional AlGaAs/GaAs MODFET's and GaAs MESFET's. The prominent generation-recombination (g-r) noise bulge commonly observed in the vicinity of 10 kHz in conventional MODFET's at 300 K does not appear in the case of the new InGaAs quantum-well MODFET. Instead, its noise spectra indicate the presence of low-intensity multiple g-r noise components superimposed on a reduced 1/f noise. The LF noise intensity in the new device appears to be the lowest among those observed in any MODFET or MESFET. The noise spectra at 82 K in the new device represent nearly true 1/f noise. This unusual low-noise behavior of the new structure suggests the effectiveness of electron confinement in the quantum well that significantaly reduces electron trapping in the n-AlGaAs, and thus eliminates the g-r noise bulge observed in conventional MODFET's.

Liu, Shih-Ming J.↗
NASA NTRS1988

Optical communication with semiconductor laser diodes

Slot timing recovery in a direct detection optical PPM communication system can be achieved by processing the photodetector waveform with a nonlinear device whose output forms the input to a phase lock group. The choice of a simple transition detector as the nonlinearity is shown to give satisfactory synchronization performance. The rms phase error of the recovered slot clock and the effect of slot timing jitter on the bit error probability were directly measured. The experimental system consisted of an AlGaAs laser diode (lambda = 834 nm) and a silicon avalanche photodiode (APD) photodetector and used Q=4 PPM signaling operated at a source data rate of 25 megabits/second. The mathematical model developed to characterize system performance is shown to be in good agreement with actual performance measurements. The use of the recovered slot clock in the receiver resulted in no degradation in receiver sensitivity compared to a system with perfect slot timing. The system achieved a bit error probability of 10 to the minus 6 power at received signal energies corresponding to an average of less than 60 detected photons per information bit.

Davidson, F.↗
NASA NTRS1988

Generation of high-power nanosecond pulses from laser diode-pumped Nd:YAG lasers

Simulation results are used to compare the pulse energy levels and pulse energy widths that can be achieved with LD-pumped Nd:YAG lasers for both the pulse-transmission mode (PTM) and pulse-reflection mode (PRM) Q-switching methods for pulse energy levels up to hundreds of microjoules and pulse widths as short as 1 ns. It is shown that high-power pulses with pulse widths as short as 1 ns can be generated with PTM Q-switched in LD-pumped Nd:YAG lasers. With the PRM Q-switching method, pulse widths as short as 2 ns and pulse energy at the level of a few hundred microjoules can also be achieved but require pumping with 8-10-mJ AlGaAs laser diode arrays.

Chan, Kinpui↗
NASA NTRS1987

GaAs/AlGaAs heterostructure point-contact concentrator cells

Point-contact cells fabricated in silicon have recently achieved very high efficiencies. Applying this structure to GaAs is difficult as it requires both surface passivation of the GaAs and a film of GaAs with thickness less than 10 microns. The authors propose to overcome these difficulties by (1) using AlGaAs layers grown by OMCVD to act as front- and back-surface fields in order to confine the photogenerated minority carriers away from the surfaces, and (2) using the CLEFT technology to produce thin, separated films of this structure. It has been found that much of the necessary technologies have been developed and that the primary problem remaining to be solved is localized junction formation.

Gale, R. P.↗
NASA NTRS1988

Semiconductor lasers for space sensor applications

Despite their intrinsic power limitations, semiconductor laser diodes are essential for laser-based spaceborne sensor systems covering a wide spectral range, fulfilling such roles as pumping and injection-locking. They may also be used as direct sources in shorter-range operations. AlGaAs laser arrays have been developed for 810-nm band pumping in Nd:YAG lasers otherwise emitting at 1.064 nm. Additional roles include their use as low-power injection seeds, locking a solid-state laser into a specific desired wavelength.

Katz, Joseph↗
NASA NTRS1988

Al(0.3)Ga(0.7)As / Al(0.05)Ga(0.95)As light-emitting diodes on GaAs-coated Si substrates grown by liquid phase epitaxy

Al(0.3)Ga(0.7)As/Al(0.05)Ga(0.95)As double-heterostructure light-emitting diodes (LEDs) were successfully grown for the first time by liquid phase epitaxy on a GaAs-coated Si substrate that was prepared by a sequential process of migration-enhanced epitaxy and molecular beam epitaxy. The edge-emitting LEDs had diode ideality factors of 1.54 at a forward-biased voltage higher than 0.9 V and external quantum efficiencies of 0.0033 W/A per facet. This efficiency is 50 times higher than the previously reported value, and is on the same order as that of AlGaAs homojunction LEDs fabricated on the GaAs substrates by liquid phase epitaxy.

Sakai, Shiro↗
NASA NTRS1988

Monolithic two-dimensional surface-emitting arrays of GaAs/AlGaAs diode lasers

Monolithic two-dimensional arrays of GaAs/AlGaAs diode lasers with light emission normal to the surface have been obtained by fabricating edge-emitting quantum-well lasers coupled with external mirrors that deflect the radiation from the laser facets by 90 degrees. Linear arrays of GaAs/AlGaAs devices in which one of the laser facets was cleaved while the other facet and an adjacent 45 degree deflector were formed by ion-beam-assisted etching (IBAE) have been reported. For the arrays reported in this section, IBAE was used to form all of the laser facets and the deflecting mirrors. A mass transport process of the type employed to fabricate two-dimensional arrays of GaInAsP/InP lasers coupled with deflecting mirrors is not known for AlGaAs.

Source record↗
NASA NTRS1988

New MBE buffer for micron- and quarter-micron-gateGaAs MESFETs

A new buffer layer has been developed that eliminates backgating in GaAs MESFETs and substantially reduces short-channel effects in GaAs MESFETs with 0.27-micron-long gates. The new buffer is grown by molecular beam epitaxy (MBE) at a substrate temperature of 200 C using Ga and As sub 4 beam fluxes. The buffer is crystalline, highly resistive, optically inactive, and can be overgrown with high quality GaAs. GaAs MESFETs with a gate length of 0.27 microns that incorporate the new buffer show improved dc and RF properties in comparison with a similar MESFET with a thin undoped GaAs buffer. To demonstrate the backgating performance improvement afforded by the new buffer, MESFETs were fabricated using a number of different buffer layers and structures. A schematic cross section of the MESFET structure used in this study is shown. The measured gate length, gate width, and source-drain spacing of this device are 2,98, and 5.5 microns, respectively. An ohmic contact, isolated from the MESFET by mesa etching, served as the sidegate. The MESFETs were fabricated in MBE n-GaAs layers grown on the new buffer and also in MBE n-GaAs layers grown on buffer layers of undoped GaAs, AlGaAs, and GaAs/AlGaAs superlattices. All the buffer layers were grown by MBE and are 2 microns thick. The active layer is doped to approximately 2 x 10 to the 17th/cu cm with silicon and is 0.3 microns thick.

Source record↗
NASA NTRS1988

Temperature coefficients for concentrator cells at various electron and proton fluence levels

Data are presented on the Isc, Voc and Pmax temperature coefficients for several small concentrator solar cells. The cells are AlGaAs (1.72 eV), GaAs, silicon and InGaAs (1.1 eV) concentrator cells operating at 6.25 and 100 times AM0. The temperature range covered was 25 to 100 C. Cells were irradiated with 1-MeV electrons and 37-MeV protons, and data are presented at different fluence levels.

Curtis, Henry B.↗
NASA NTRS1988

High-power 0.87-micron channel substrate planar lasers for spaceborne communications

High-power single-mode channeled-substrate planar AlGaAs diode lasers are being developed for reliable high-power operation for use as sources in spaceborne optical communication systems. The CSP laser structure has been optimized for operation at an emission wavelength of 870 nm. Such devices have exhibited output powers in excess of 80 mW CW at an operating temperature of 80 C.

Connolly, J. C.↗
NASA NTRS1988

Gaussian approximation versus nearly exact performance analysis of optical communication systems with PPM signaling and APD receivers

A 25-Mb/s direct-detection optical communication system that used Q = 4 PPM (pulse-position modulation) signaling was constructed and its performance measured under laboratory conditions. The system used a single-mode AlGaAs laser diode (lambda = 834 nm) and low-noise silicon avalanche photodiode (APD). A procedure for numerically computing system performance is given that uses the nearly exact Webb approximation of the true Conradi distribution for the APD output and does not require excessive amounts of computer time. Comparison revealed that modeling the APD ouptut as a Gaussian process under conditions of negligible background radiation and low (less than 10 to the -12 A) APD bulk leakage currents leads to substantial underestimates of optimal APD gain and overestimates of system bit error probability. Examples illustrate the breakdown of the Gaussian approximation in assessing system performance. The measured performance was in excellent agreement with that predicted by the computational procedure. The system achieved a bit error probability of 10 to the -6 at a received signal energy, corresponding to an average of 60 absorbed photons/bit and optimal APD gain of 700.

Davidson, Frederic M.↗
NASA NTRS1989

Characterization of multilayer GaAs/AlGaAs transistor structures by variable angle spectroscopic ellipsometry

Variable angle of incidence spectroscopic ellipsometry (VASE) has been implemented as a means of determining layer thickness, alloy composition, and growth quality of GaAs/AlGaAs samples composed of relatively thick layers as well as superlattices. The structures studied in this work contained GaAs/AlGaAs multilayers with a superlattice 'barrier' and were grown for later formation of modulation-doped field effect transistors (MODFETs). Sample modeling was performed by treating the superlattice as a bulk AlGaAs layer of unknown composition. Extremely good data fits were realized when five layer thicknesses and two alloy ratios were allowed to vary in a regression analysis. Room temperature excitonic effects associated with the e-hh(1), e-lh(1) and e-hh(2) transitions were observed in the VASE data.

Merkel, Kenneth G.↗
NASA NTRS1990

Optically-Tuned Far-Infrared Device

Spacing of visible interference pattern determines frequency of infrared radiation. Variable photoconductivity grating formed by interference of two visible laser beams intersecting on surface of proposed AlGaAs device substituted for fixed metal grating. Proposed device provides higher output-power density and greater tunability.

Katz, Joseph↗
NASA NTRS1990

Multi-Quantum-Well Spatial Light Modulators On Si Substrates

Proposed new class of two-dimensional spatial light modulators (SLM's) based on fabrication of multi-quantum-well (MQW) structures (e.g. of AlGaAs and InGaAs) on silicon substrates. Concept makes two-dimensional SLM arrays by taking advantage of mature technology of silicon charge-coupled devices (CCD's). Features include short response times, high resolution, and low switching energies.

Cutts, James A.↗
NASA NTRS1989

Monolithically integrated two-dimensional arrays of optoelectronic threshold devices for neural network applications

A monolithic 10 x 10 two-dimensional array of 'optical neuron' optoelectronic threshold elements for neural network applications has been designed, fabricated, and tested. Overall array dimensions are 5 x 5 mm, while the individual neurons, composed of an LED that is driven by a double-heterojunction bipolar transistor, are 250 x 250 microns. The overall integrated structure exhibited semiconductor-controlled rectifier characteristics, with a breakover voltage of 75 V and a reverse-breakdown voltage of 60 V; this is attributable to the parasitic p-n-p transistor which exists as a result of the sharing of the same n-AlGaAs collector between the transistors and the LED.

Kim, J. H.↗
NASA NTRS1989

Slot clock recovery in optical PPM communication systems with avalanche photodiode photodetectors

Slot timing recovery in a direct-detection optical PPM communication system can be achieved by processing the photodetector output waveform with a nonlinear device whose output forms the input to a phase-locked loop. The choice of a simple transition detector as the nonlinearity is shown to give satisfactory synchronization performance. The rms phase error of the recovered slot clock and the effect of slot timing jitter on the bit error probability were directly measured. The experimental system consisted of an AlGaAs laser diode (wavelength = 834 nm) and a silicon avalanche photodiode photodetector. The system used Q = 4 PPM signaling and operated at a source data rate of 25 Mbits/s. The mathematical model developed to compute the rms phase error of the recovered clock is shown to be in good agreement with results of actual measurements of phase errors. The use of the recovered slot clock in the receiver resulted in no significant degradation in receiver sensitivity compared to a system with perfect slot timing. The system achieved a bit error probability of 10 to the -6th at a received optical signal energy of 55 detected photons per information bit.

Davidson, Frederic M.↗
NASA NTRS1990

Word timing recovery in direct detection optical PPM communication systems with avalanche photodiodes using a phase lock loop

A technique for word timing recovery in a direct-detection optical PPM communication system is described. It tracks on back-to-back pulse pairs in the received random PPM data sequences with the use of a phase locked loop. The experimental system consisted of an 833-nm AlGaAs laser diode transmitter and a silicon avalanche photodiode photodetector, and it used Q = 4 PPM signaling at source data rate 25 Mb/s. The mathematical model developed to describe system performance is shown to be in good agreement with the experimental measurements. Use of this recovered PPM word clock with a slot clock recovery system caused no measurable penalty in receiver sensitivity. The completely self-synchronized receiver was capable of acquiring and maintaining both slot and word synchronizations for input optical signal levels as low as 20 average detected photons per information bit. The receiver achieved a bit error probability of 10 to the -6th at less than 60 average detected photons per information bit.

Sun, Xiaoli↗
NASA NTRS1991

Self-Heterodyne Laser-Spectrum Analyzer

Apparatus measures spectral widths of light emitted by GaAs or other narrow-linewidth diode lasers at wavelengths between 800 and 900 nm. Operating on quasi-homodyne of self-heterodyne principle, apparatus provides relatively high spectral resolution: measures spectral widths of order of 100 kHz. Fine spectral resolution of apparatus provides data relevant to use of AlGaAs diode lasers in such applications as coherent optical communication through free space and injection seeding of solid-state lasers. Also used to explore connections between lifetimes and spectral widths of diode lasers.

Saif, Babak↗