Search NASA⌕ Search

SEARCH · Search NASA

Results for “Applied aerodynamics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS2012

Preliminary Design and Evaluation of an Airfoil with Continuous Trailing-Edge Flap

This paper presents the preliminary design and evaluation of an airfoil with active continuous trailing-edge flap (CTEF) as a potential rotorcraft active control device. The development of structural cross-section models of a continuous trailing-edge flap airfoil is described. The CTEF deformations with MFC actuation are predicted by NASTRAN and UM/VABS analyses. Good agreement is shown between the predictions from the two analyses. Approximately two degrees of CTEF deflection, defined as the rotation angle of the trailing edge, is achieved with the baseline MFC-PZT bender. The 2D aerodynamic characteristics of the continuous trailing-edge flap are evaluated using a CFD analysis. The aerodynamic efficiency of a continuous trailing-edge flap is compared to that of a conventional discrete trailing-edge flap (DTEF). It is found that the aerodynamic characteristics of a CTEF are equivalent to those of a conventional DTEF with the same deflection angle but with a smaller flap chord. A fluid structure interaction procedure is implemented to predict the deflection of the continuous trailingedge flap under aerodynamic pressure. The reductions in CTEF deflection are overall small when aerodynamic pressure is applied: 2.7% reduction is shown with a CTEF deflection angle of two degrees and at angle of attack of six degrees. In addition, newly developed MFC-PMN actuator is found to be a good supplement to MFC-PZT when applied as the bender outside layers. A mixed MFC-PZT and MFC-PMN bender generates 3% more CTEF deformation than an MFC-PZT only bender and 5% more than an MFC-PMN only bender under aerodynamic loads.

Shen, Jinwei↗
NASA NTRS1993

Application of a Navier-Stokes aeroelastic method to improve fighter wing performance at maneuver flight conditions

An aeroelastic analysis method, based on three-dimensional Navier-Stokes equation aerodynamics, has been applied to improve the performance of fighter wings operating at sustained maneuver flight conditions. The scheme reduces the trimmed pressure drag of wings performing high-g maneuvers through a simultaneous application of control surface deflection and aeroelastic twist. The aerodynamic and structural interactions are decoupled by assuming an aeroelastic twist mode shape and optimizing the aerodynamic performance based on this aeroelastic mode. The wing structural stiffness properties are then determined through an inverse scheme based on the aerodynamic loads and desired twist at the maneuver flight condition. The decoupled technique is verified by performing a fully coupled aeroelastic analysis using the maneuver flight conditions and the optimized structural stiffness distributions.

Schuster, David M.↗
NASA NTRS1994

Measurement Capabilities of Single-Pulse Planar Doppler Velocimetry

Preliminary investigations are described of a method that is capable of measuring instantaneous, 3-D, velocity vectors everywhere in a light sheet generated by a pulsed laser. The technique, here called Planar Doppler Velocimetry (PDV), is a variation of a new concept for velocity measurements that was called Doppler Global Velocimetry (DGV) in its original disclosure. The concept relies on the use of a narrowband laser and measurements of the Doppler shift of scattered light from particles moving with a flow. The Doppler shift is recorded as a variation in transmission through a sharp-edged spectral filter provided by iodine vapor in a cell. Entire fields of velocity can be determined by using a solid-state camera to record the intensity variations throughout the field of view. However, the implementation of DGV has been centered principally on the use of high power, continuous-wave, ion lasers and measurement times that are determined by the 30-ms framing times of standard video cameras. Hence, they provide velocity fields that are averaged in time at least over that period. On the other hand, the PDV concept described in this presentation incorporates a high energy, repetitively pulsed, Nd-YAG laser that is injection-seeded to make it narrowband and then frequency-doubled to provide light at frequencies absorbed by the iodine vapor. The duration of each pulse is less than 10 nanoseconds. When used in combination with nonstandard, scientific quality, solid state cameras, a sequence of images can be obtained that provides instantaneous velocity vectors everywhere in the field of view. The investigations described in this paper include an accurate characterization of the iodine cell spectral behavior and its influence on the PDV measurements, a derivation of the PDV signal analysis requirements, and the unique aspects of the pulsed laser behavior related to this application. In addition, PDV measurements are to be demonstrated using data from a rotating wheel target and from the flow of a subsonic jet. Initially, single optical fiber light collection and photomultiplier detectors will be substituted for solid state cameras. Those results will allow the determination of the fundamental limitations of the PDV technique without the complications of image acquisition and processing. They will then be used to provide an analysis of the measurement capabilities of PDV both in small aerodynamic research wind tunnels and in large wind tunnels designed for production airframe and propulsion testing. Future plans include the implementation of solid state cameras and the development of the required image acquisition and processing software. Eventually, the PDV technique will be applied to an aerodynamic research program related to transonic wing flutter.

McKenzie, Robert L.↗
NASA NTRS2004

Multiobjective Aerodynamic Shape Optimization Using Pareto Differential Evolution and Generalized Response Surface Metamodels

Differential Evolution (DE) is a simple, fast, and robust evolutionary algorithm that has proven effective in determining the global optimum for several difficult single-objective optimization problems. The DE algorithm has been recently extended to multiobjective optimization problem by using a Pareto-based approach. In this paper, a Pareto DE algorithm is applied to multiobjective aerodynamic shape optimization problems that are characterized by computationally expensive objective function evaluations. To improve computational expensive the algorithm is coupled with generalized response surface meta-models based on artificial neural networks. Results are presented for some test optimization problems from the literature to demonstrate the capabilities of the method.

Madavan, Nateri K.↗
NASA NTRS1990

The application of active controls technology to a generic hypersonic aircraft configuration

Analytical methods are described for the prediction of aerothermoelastic stability of hypersonic aircraft including active control systems. Thermal loads due to aerodynamic heating were applied to the finite element model of the aircraft structure and the thermal effects on flutter were determined. An iterative static aeroelastic trim analysis procedure was developed including thermal effects. And active control technology was assessed for flutter suppression, ride quality improvement, and gust load alleviation to overcome any potential adverse aeroelastic stability or response problems due to aerodynamic heating. A generic hypersonic aircraft configuration was selected which incorporates wing flaps, ailerons, and all moveable fins to be used for active control purposes. The active control system would use onboard sensors in a feedback loop through the aircraft flight control computers to move the surfaces for improved structural dynamic response as the aircraft encounters atmospheric turbulence.

Gilbert, M. G.↗
NASA NTRS2013

Rocket Sled Propelled Testing of a Supersonic Inflatable Aerodynamic Decelerator

Decelerators (IADs) have traditionally been tested in wind tunnels. As the limitations of these test facilities are reached, other avenues must be pursued. The IAD being tested is a Supersonic IAD (SIAD), which attaches just aft of the heatshield around the perimeter of an entry body. This 'attached torus' SIAD is meant to improve the accuracy of landing for robotic class missions to Mars and allow for potentially increased payloads. The SIAD Design Verification (SDV) test aims to qualify the SIAD by applying a targeted aerodynamic load to the vehicle. While many test architectures were researched, a rocket sled track was ultimately chosen to be the most cost effective way to achieve the desired dynamic pressures. The Supersonic Naval Ordnance Research Track (SNORT) at the Naval Air Warfare Center Weapons Division (NAWCWD) China Lake is a four mile test track, traditionally used for warhead and ejection seat testing. Prior to SDV, inflatable drag bodies have been tested on this particular track. Teams at Jet Propulsion Laboratory (JPL) and NAWCWD collaborate together to design and fabricate one of the largest sleds ever built. The SDV sled is comprised of three individual sleds: a Pusher Sled which holds the solid booster rockets, an Item Sled which supports the test vehicle, and a Camera Sled that is pushed in front for in-situ footage and measurements. The JPL-designed Test Vehicle has a full-scale heatshield shape and contains all instrumentation and inflation systems necessary to inflate and test a SIAD. The first campaign that is run at SNORT tested all hardware and instrumentation before the SIAD was ready to be tested. For each of the three tests in this campaign, the number of rockets and top speed was increased and the data analyzed to ensure the hardware is safe at the necessary accelerations and aerodynamic loads.

Supersonic Inflatable Aerodynamic Decelerators (SI↗
NASA NTRS1992

Aeroelastic stability analyses of two counter rotating propfan designs for a cruise missile model

A modal aeroelastic analysis combining structural and aerodynamic models is applied to counterrotating propfans to evaluate their structural integrity for wind-tunnel testing. The aeroelastic analysis code is an extension of the 2D analysis code called the Aeroelastic Stability and Response of Propulsion Systems. Rotational speed and freestream Mach number are the parameters for calculating the stability of the two blade designs with a modal method combining a finite-element structural model with 2D steady and unsteady cascade aerodynamic models. The model demonstrates convergence to the least stable aeroelastic mode, describes the effects of a nonuniform inflow, and permits the modification of geometry and rotation. The analysis shows that the propfan designs are suitable for the wind-tunnel test and confirms that the propfans should be flutter-free under the range of conditions of the testing.

Mahajan, Aparajit J.↗
NASA NTRS1995

Application of Pressure Sensitive Paint in Hypersonic Flows

It is well known in the aerodynamic field that pressure distribution measurement over the surface of an aircraft model is a problem in experimental aerodynamics. For one thing, a continuous pressure map can not be obtained with the current experimental methods since they are discrete. Therefore, interpolation or CFD methods must be used for a more complete picture of the phenomenon under study. For this study, a new technique was investigated which would provide a continuous pressure distribution over the surface under consideration. The new method is pressure sensitive paint. When pressure sensitive paint is applied to an aerodynamic surface and placed in an operating wind-tunnel under appropriate lighting, the molecules luminesce as a function of the local pressure of oxygen over the surface of interest during aerodynamic flow. The resulting image will be brightest in the areas of low pressure (low oxygen concentration), and less intense in the areas of high pressure (where oxygen is most abundant on the surface). The objective of this investigation was to use pressure sensitive paint samples from McDonnell Douglas (MDD) for calibration purpose in order to assess the response of the paint under appropriate lighting and to use the samples over a flat plate/conical fin mounted at 75 degrees from the center of the plate in order to study the shock/boundary layer interaction at Mach 6 in the Von Karman wind-tunnel. From the result obtained it was concluded that temperature significantly affects the response of the paint and should be given the uppermost attention in the case of hypersonic flows. Also, it was found that past a certain temperature threshold, the paint intensity degradation became irreversible. The comparison between the pressure tap measurement and the pressure sensitive paint showed the right trend. However, there exists a shift when it comes to the actual value. Therefore, further investigation is under way to find the cause of the shift.

Jules, Kenol↗
NASA NTRS1999

Aero-Structural Optimization of HSCT Configurations in Transonic and Supersonic Flow

This document outlines the progress made under NASA Cooperative Research Agreement NCC2- 5226 for the period 10/01/97-09/30/98. The work statement originally proposed was meant to extend over the period of two complete years of which only one was funded. Consequently, only a portion of the goals were achieved. Similar work will continue in our group under different sponsorship and will be available in the form of conference and journal publications. The following sections summarize the technical accomplishments obtained during the last year. Details of these accomplishments can be found in the accompanying paper that was presented at the AIAA 37th Aerospace Sciences and Exhibit Meeting which was held in Reno, NV in January of this year. The original proposal outlined a research program meant to lay down the foundation for the development of high-fidelity, fully-coupled aerodynamic/structural optimization methods applicable to a variety of aerospace applications including the design optimization of High Speed Civil Transport (HSCT) configurations. The necessary research and development work was divided into two main efforts which addressed the necessities of the long term goal. Initially, our experience in the simulation of unsteady aeroelastic flows was directly applied to existing aerodynamic optimization techniques in order to provide insight into the effects of aeroelastic deformations on the performance of aircraft which have been designed based on purely aerodynamic cost functions. The intention was to follow up this work with a detailed investigation into the basic research work that has to be completed for the development of an optimization framework which efficiently allows the truly coupled design of aero-structural systems. This follow-up effort was not funded. The outcome of our efforts during the past year was the development of a coupled aero-structural analysis and design environment that was applied to the design of a complete aircraft configuration.

Alonso, Juan J.↗
NASA NTRS1980

Use of advanced computers for aerodynamic flow simulation

The current and projected use of advanced computers for large-scale aerodynamic flow simulation applied to engineering design and research is discussed. The design use of mature codes run on conventional, serial computers is compared with the fluid research use of new codes run on parallel and vector computers. The role of flow simulations in design is illustrated by the application of a three dimensional, inviscid, transonic code to the Sabreliner 60 wing redesign. Research computations that include a more complete description of the fluid physics by use of Reynolds averaged Navier-Stokes and large-eddy simulation formulations are also presented. Results of studies for a numerical aerodynamic simulation facility are used to project the feasibility of design applications employing these more advanced three dimensional viscous flow simulations.

Bailey, F. R.↗
NASA NTRS1994

Measuring the Thermal Accommodation Coefficient while Aerobraking Magellan

The Magellan spacecraft was inserted into an elliptical orbit around the planet Venus on August 10, 1990. A small aerodynamic force was applied later to the spacecraft for 730 consecutive orbits to lower the apoapsis of the orbit from 8500 km to 541 km. Atmospheric drag removed a maximum of 2 m/sec per orbit from the velocity at periapsis for a total delta-V of 1200 m/sec. This paper will discuss the thermal accommodation coefficient which was inferred from one of the four solar panel temperature measurements from the aerobraking pass through the atmosphere.

measurements thermal accomodation coefficient↗
NASA NTRS1986

Estimation of aerodynamic parameters from flight data of a high incidence research model

A procedure for the determination of an aerodynamic model structure and aerodynamic parameters is applied to flight data from a high-incidence research model (HIRM) within an angle of attack range of 18 to 40 degrees. The HIRM is a three-surface unpowered model with a swept wing, an all-moving canard and stabilator, and a vertical tail with rudder. The motion of the HIRM was excited first by its release from the helicopter and then by the activation of control surfaces. This paper briefly describes the model, flight and wind tunnel data available, equations of motion and techniques for data analysis. The results presented contain an example of a measured data compatibility and the variation of some important stability derivatives with the angle of attack and canard setting. The derivatives were obtained from various maneuvers and subsets of joined data from several maneuvers by using a stepwise-regression technique. These derivatives agreed, in general, with the results of wind-tunnel measurements. The resulting lateral aerodynamic model equations could predict the motion of the HIRM reasonably well.

Klein, V.↗
NASA NTRS1974

Computer program for supersonic Kernel-function flutter analysis of thin lifting surfaces

This report describes a computer program (program D2180) that has been prepared to implement the analysis described in (N71-10866) for calculating the aerodynamic forces on a class of harmonically oscillating planar lifting surfaces in supersonic potential flow. The planforms treated are the delta and modified-delta (arrowhead) planforms with subsonic leading and supersonic trailing edges, and (essentially) pointed tips. The resulting aerodynamic forces are applied in a Galerkin modal flutter analysis. The required input data are the flow and planform parameters including deflection-mode data, modal frequencies, and generalized masses.

Cunningham, H. J.↗
NASA NTRS1979

The size and performance effects of high lift system technology on a modern twin engine jet transport

The energy and economic benefits of low-speed aerodynamic system technology applied to a modern 200-passenger, 2000-nmi range, twin engine jet transport are reviewed. Results of a new method to design flap systems at flight Reynolds number are summarized. The study contains the airplane high lift configuration drag characteristics and design selection charts showing the effect of flap technology on the airplane size and performance. The study areas include: wing and flap geometry, climb and descent speed schedules with partial flap deflection, flap system technology, and augmented stability. The results compare the improvements in payload from a hot, high elevation airport.

Sullivan, R. L.↗
NASA NTRS1986

Calculation of helicopter airfoil characteristics for high tip-speed applications

In this paper, we have applied a new aerodynamic tool to the study of helicopter airfoil characteristics. We have shown that the computed airloads reproduce completely the experimental behavior of representative airfoils across the transonic regime. In addition, the computational details of the flow fields, the surface pressure distributions, and the viscous-layer characteristics enable us to trace the evolution of the physical changes that occur as m infinity or Re increases. Descriptions of the complicated development of shock waves, shock-induced separation supplement the information that has been obtained heretofore in wind tunnels. In validating our calculations and assessing the accuracy of the results, including extensive grid-refinement studies and comparisons with data from numerous wind tunnels, we have defined the capabilities and limitations of the code ARC2D more precisely. This important aspect of the investigations can complement wind-tunnel tests, by providing flow-field details that are difficult to measure and by extending the range of low parameters beyond the capabilities of existing wind tunnels. The code has now progressed from a purely research stage to almost a production stage, where it can be run by specialists in the helicopter industry.

Mccroskey, W. J.↗
NASA NTRS1988

Vortical flow analysis for F-106B configuration

The three-dimensional Euler aerodynamic method is applied to basic F-106B wing-fuselage geometries over an angle-of-attack range in the subsonic and transonic speeds to examine vortical flow behavior. The use of this method to provide meaningful vortex breakdown information is explored. This Euler solution algorithm uses a C-H mesh with 80625 grid points to represent the flowfield. Contours of axial velocity and total pressure, spanwise surface pressure and velocity vectors at cross flow planes, together with contours of suction pressure and total pressure on the leeward surface of the wing, were used to examine the vortex breakdown details.

Pao, Jenn Louh↗
NASA NTRS1988

Aeronautical engineering: A continuing bibliography with indexes (supplement 233)

This bibliography lists 637 reports, articles, and other documents introduced into the NASA scientific and technical information system in November, 1988. Subject coverage includes: design, construction and testing of aircraft and aircraft engines; aircraft components, equipment and systems; ground support systems; and theoretical and applied aspects of aerodynamics and general fluid dynamics.

Source record↗