SEARCH · Search NASA

Results for “Asymmetric vortices”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

All sources NASA NTRS DOE OSTI

NASA NTRS1993

Aerodynamic control of NASP-type vehicles through vortex manipulation. Volume 3: Wing rock experiments

Free-to-roll tests were conducted in water and wind tunnels in an effort to investigate the mechanisms of wing rock on a NASP-type vehicle. The configuration tested consisted of a highly-slender forebody and a 78 deg swept delta wing. In the water tunnel test, extensive flow visualization was performed and roll angle histories were obtained. In the wind tunnel test, the roll angle, forces and moments, and limited forebody and wing surface pressures were measured during the wing rock motion. A limit cycle oscillation was observed for angles of attack between 22 deg and 30 deg. In general, the experiments confirmed that the main flow phenomena responsible for the wing-body-tail wing rock are the interactions between the forebody and the wing vortices. The variation of roll acceleration (determined from the second derivative of the roll angle time history) with roll angle clearly slowed the energy balance necessary to sustain the limit cycle oscillation. Different means of suppressing wing rock by controlling the forebody vortices using small blowing jets were also explored. Steady blowing was found to be capable of suppressing wing rock, but significant vortex asymmetrices are created, causing the model to stop at a non-zero roll angle. On the other hand, alternating pulsed blowing on the left and right sides of the fore body was demonstrated to be a potentially effective means of suppressing wing rock and eliminating large asymmetric moments at high angles of attack.

Suarez, Carlos J.↗

NASA NTRS1978

Symmetrical and asymmetrical separations about a yawed cone

Three dimensional flow separations about a circular cone were investigated in the Mach number range 0.6 - 1.8. The cone was tested in the Ames 1.8 by 1.8 m wind tunnel at Reynolds numbers based on the cone length from 4,500,000 to 13,500,000 under nominally zero heat transfer conditions. Results indicate that: (1) the lee-side separated flow develops from initially symmetrically disposed and near-conical separation lines at angle of incidence/cone semiangle equal to approximately 1, with the free shear layers eventually rolling up into tightly coiled vortices at all Mach numbers; (2) the onset of asymmetry of the lee-side separated flow about the mean pitch plane is sensitive to Mach number, Reynolds number, and the nose bluntness; and (3) as the Mach number is increased beyond 1.8, the critical angle of incidence for the onset of asymmetry increases until at about M = 2.75 there is no longer any significant side force development.

Peake, D. J.↗

NASA NTRS1992

Three-dimensional structure of a curved wake

The effects of streamwise curvature on the 3D structure of a plane wake are studied. Preliminary results indicate that the wake is initially grossly 3D with large spanwise distortions in the mean velocity and Reynolds stress contours. Local extrema distributed in a quasi-periodic manner are seen. The spanwise variations are caused by the presence of relatively strong quadrupoles of mean streamwise vorticity. Further downstream the mean vorticity decays at a rate lower on the unstable side of the wake so that only the unstable side row of vortices persist to the far-field region. As a result, the spanwise distortions and local extrema seem to persist with a relatively slow decay. The effects of curvature are also apparent in the Reynolds stress results. In particular, the shear stress is significantly affected by curvature right from the start such that significantly higher magnitudes are observed on the unstable side. The curved wake clearly develops a very 3D asymmetric structure which shows no signs of reaching an equilibrium state.

Weygandt, J. H.↗

NASA NTRS2016

MMS Observations of Electron-Scale Filamentary Currents in the Reconnection Exhaust and Near the X Line

We report Magnetospheric Multiscale observations of macroscopic and electron-scale current layers in asymmetric reconnection. By intercomparing plasma, magnetic, and electric field data at multiple crossings of a reconnecting magnetopause on 22 October 2015, when the average interspacecraft separation was approximately 10 km, we demonstrate that the ion and electron moments are sufficiently accurate to provide reliable current density measurements at 30ms cadence. These measurements, which resolve current layers narrower than the interspacecraft separation, reveal electron-scale filamentary Hall currents and electron vorticity within the reconnection exhaust far downstream of the X line and even in the magnetosheath. Slightly downstream of the X line, intense (up to 3 μA/m2) electron currents, a super-Alfvenic outflowing electron jet, and nongyrotropic crescent shape electron distributions were observed deep inside the ion-scale magnetopause current sheet and embedded in the ion diffusion region. These characteristics are similar to those attributed to the electron dissipation/diffusion region around the X line.

Phan, T. D.↗

NASA NTRS1995

Simulations Of On Demand Vortex Generators

The development of a two-dimensional viscous incompressible flow generated by an off center thin oscillating bd on top of a cavity is studied computationally as a prototype of vortex generators. The lid is placed asymmetrically over the cavity so that the gap size is different on either side of the cavity. An adaptive numerical scheme, based on high resolution viscous vortex methods, is used to integrate the vorticity/velocity formulation of the Navier-Stokes equations with the no-slip boun.lary condition enforced on the lid and cavity walls. Depending on the a amplitude and frequency of the oscillation as well as the the gap size, vorticity is ejected in the fluid above the cavity either from the large and/or the small gap. The results of the computations complement ongoing experimental work.

Koumoutsakos, P.↗

NASA NTRS1984

Large-scale stationary and turbulent flow over topography

The contributions made to the formation of stationary features of flow over topography by linear and nonlinear dynamics were examined with an integrated quasi-geostrophic model with idealized topographic forcing. The simulation was run out to several months and generated time-averaged values which were compared with those obtained with linear theory. Linear predictions were converted to turbulent features through the addition of stationary, nonlinear thermodynamic and transient vorticity fluxes. The turbulence features matched atmospheric data on energy spectra, the direction and magnitude of energy transfers, and the spatial magnitudes involved. Transient flow transferred the majority of energy absorbed by the upscale flow and, by absorbing energy, reduced the energy of stationary flow while retaining resonance signatures. Instability was a pervasive feature of the topographically forced flow except at high wavenumbers. The results confirm that transient eddies are interactive with both asymmetric and zonal flow and cannot be adequately described by linear theory.

Vallis, G. K.↗

NASA NTRS1985

Measurements of canard-induced roll oscillations

A small canard wing was installed in front of a delta wing which was mounted on a free-to-roll sting balance in a low-speed wind tunnel. The leading edge vortices, originating from the canard, enhanced self-induced roll oscillations at test conditions for which the basic delta wing would otherwise have been stable. Time-dependent roll angle, and normal and side force data recorded during these oscillations are presented along with their phase relations. It was found that the canard increased the range of angle of attack at which self-induced oscillations occurred. Also, at an angle of attack of about 46 deg asymmetric oscillations are observed.

Katz, J.↗

NASA NTRS1989

Development of non-conventional control methods for high angle of attack flight using vortex manipulation

Low-speed wind tunnel experiments have been conducted to define methods for the manipulation of a generic fighter forebody's vortices in order to generate controlled yawing moments at high alpha. Attention is given to two vortex-control schemes: one involving independently controlled forebody tip strakes, and the other individually controlled blowing ports on the forebody. The most effective methods for forebody yawing-moment control were found to be the minimization of natural asymmetry with a pair of symmetrically mounted tip strakes, and the perturbation of the vortex system away from the symmetric condition with asymmetric blowing.

Malcolm, Gerald N.↗

DOE OSTI2022

Studying the Richtmyer–Meshkov instability in convergent geometry under high energy density conditions using the Decel platform

The “Decel” platform at Sandia National Laboratories investigates the Richtmyer–Meshkov instability (RMI) in converging geometry under high energy density conditions [Knapp et al., Phys. Plasmas 27, 092707 (2020)]. In Decel, the Z machine magnetically implodes a cylindrical beryllium liner filled with liquid deuterium, launching a converging shock toward an on-axis beryllium rod machined with sinusoidal perturbations. The passage of the shock deposits vorticity along the Be/D2 interface, causing the perturbations to grow. Here, we present platform improvements along with recent experimental results. To improve the stability of the imploding liner to the magneto Rayleigh–Taylor instability, we modified its acceleration history by shortening the Z electrical current pulse. Next, we introduce a “split rod” configuration that allows two axial modes to be fielded simultaneously in different axial locations along the rod, doubling our data per experiment. We then demonstrate that asymmetric slots in the return current structure modify the magnetic drive pressure on the surface of the liner, advancing the evolution on one side of the rod by multiple ns compared to its 180° counterpart. This effectively enables two snapshots of the instability at different stages of evolution per radiograph with small deviations of the cross-sectional profile of the rod from the circular. Using this platform, we acquired RMI data at 272 and 157 μm wavelengths during the single shock stage. Finally, we demonstrate the utility of these data for benchmarking simulations by comparing calculations using ALEGRA MHD and RageRunner.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

NASA NTRS2003

High-Resolution Simulation of Hurricane Bonnie (1998): The Organization of Vertical Motion - Part 1

Hurricanes are well known for their strong winds and heavy rainfall, particularly in the intense rainband (eyewall) surrounding the calmer eye of the storm. In some hurricanes, the rainfall is distributed evenly around the eye so that it has a donut shape on radar images. In other cases, the rainfall is concentrated on one side of the eyewall and nearly absent on the other side and is said to be asymmetric. This study examines how the vertical air motions that produce the rainfall are distributed within the eyewall of an asymmetric hurricane and the factors that cause this pattern of rainfall. We use a sophisticated numerical forecast model to simulate Hurricane Bonnie, which occurred in late August of 1998 during a special NASA field experiment designed to study hurricanes. The simulation results suggest that vertical wind shear (a rapid change in wind speed or direction with height) caused the asymmetric rainfall and vertical air motion patterns by tilting the hurricane vortex and favoring upward air motions in the direction of tilt. Although the rainfall in the hurricane eyewall may surround more than half of the eye, the updrafts that produce the rainfall are concentrated in very small-scale, intense updraft cores that occupy only about 10% of the eyewall area. The model simulation suggests that the timing and location of individual updraft cores are controlled by intense, small-scale vortices (regions of rapidly swirling flow) in the eyewall and that the updrafts form when the vortices encounter low-level air moving into the eyewall.

Braun, Scott A.↗

NASA NTRS1990

Development of non-conventional control methods for high angle of attack flight using vortex manipulation

Methods of manipulating the forebody vortices on a generic fighter model to produce controlled yawing moments at high angles of attack were investigated. Forces and moments were measured on the complete configuration and on the isolated forebody. Two schemes for vortex control on the forebody were evaluated: individually-controlled tip strakes and individually-controlled blowing ports. The effectiveness of the forebody strakes in controlling forebody side forces was strongly dependent on the size and location of the strakes. A yawing moment can be produced by deploying the forebody strakes asymmetrically, or can be eliminated by deploying the strakes symmetrically. The most effective strake position was found to be near the primary separation point, between 105 and 120 deg from windward. Blowing on the surface of the model was also shown to have a strong effect on the yawing moment. Blowing either forward or aft tangential to the surface appears to be more effective than blowing normal to the surface. The most effective method to control the yawing moment on the forebody was to minimize the natural asymmetry with a pair of small symmetrically mounted tip strakes and to perturb the vortex system away from the symmetric condition with asymmetric blowing.

Malcolm, Gerald N.↗

NASA NTRS1979

Control of forebody three-dimensional flow separations

The development of the turbulent symmetric and asymmetric vortex flow about the lee side of a 5 deg semiangle conical forebody at high relative incidence was investigated. The cone was immersed in a Mach 0.6 airstream at a Reynolds number of 13.5 x 10 to the 6th power based on the 1.4 m axial length of the cone. Small amounts of air injected normally or tangentially to the cone surface, but on one side of the leeward meridian and beneath the vortex farthest from the wall, were effective in biasing the asymmetry. With this reorientation of the forebody vortices, the amplitude of the side force could be reduced to the point where its direction was reversed. This phenomenon was obtained either by changing the blowing rate at constant incidence or by changing incidence at constant blowing rate. Normal injection appeared more effective than tangential injection. The contrarotating vortices in the penetrating jet flow were of opposite hand to the rotational directions of the forebody vortices. A distinctively organized and stable flow structure emerged with the jet vortices positioned above the forebody vortices.

Peake, D. J.↗

NASA NTRS1993

CFD analyses of coolant channel flowfields

The flowfield characteristics in a rocket engine coolant channels are analyzed by means of a numerical model. The channels are characterized by large length to diameter ratios, high Reynolds numbers, and asymmetrical heating. At representative flow conditions, the channel length is approximately twice the hydraulic entrance length so fully developed conditions are reached. The supercritical hydrogen coolant introduces strong property variations that have a major influence on the developing flow and the resulting heat transfer. Comparisons of constant and variable property solutions show substantial differences. The density variation accelerates the fluid in the channels increasing the pressure drop without an accompanying increase in heat flux. Analyses of the inlet configuration suggest that side entry from a manifold can affect the development of the velocity profile because of vortices generated as the flow enters the channel.

Yagley, J. A.↗

NASA NTRS2012

The Impact of Dry Midlevel Air on Hurricane Intensity in Idealized Simulations with No Mean Flow

This study examines the potential negative influences of dry midlevel air on the development of tropical cyclones (specifically, its role in enhancing cold downdraft activity and suppressing storm development). The Weather Research and Forecasting model is used to construct two sets of idealized simulations of hurricane development in environments with different configurations of dry air. The first set of simulations begins with dry air located north of the vortex center by distances ranging from 0 to 270 km, whereas the second set of simulations begins with dry air completely surrounding the vortex, but with moist envelopes in the vortex core ranging in size from 0 to 150 km in radius. No impact of the dry air is seen for dry layers located more than 270 km north of the initial vortex center (approximately 3 times the initial radius of maximum wind). When the dry air is initially closer to the vortex center, it suppresses convective development where it entrains into the storm circulation, leading to increasingly asymmetric convection and slower storm development. The presence of dry air throughout the domain, including the vortex center, substantially slows storm development. However, the presence of a moist envelope around the vortex center eliminates the deleterious impact on storm intensity. Instead, storm size is significantly reduced. The simulations suggest that dry air slows intensification only when it is located very close to the vortex core at early times. When it does slow storm development, it does so primarily by inducing outward- moving convective asymmetries that temporarily shift latent heating radially outward away from the high-vorticity inner core.

Weather Research and Forecasting model↗

DOE OSTI2025

Observation of Persistent Zero Modes and Superconducting Vortex Doublets in UTe 2

Superconducting vortices can reveal electron pairing details and nucleate topologically protected states. Yet, vortices of bulk spin-triplet superconductors have never been visualized at the atomic scale. Recently, UTe 2 has emerged as a prime spin-triplet superconductor, but its superconducting order parameter is elusive, and whether time-reversal symmetry (TRS) is broken remains unsettled. Here, in this work, we visualize vortices on the (011) surface of ultraclean UTe 2 single crystals (T c = 2.1 K) using scanning tunneling microscopy (STM). We introduce $\frac{d^{2}𝐼}{d𝑉^{2}}$ imaging as an effective technique for vortex visualization in superconductors with substantial residual zero-energy density of states (DOS), as in UTe 2 . Anisotropic single-flux-quantum vortices, with coherence lengths of ∼12 nm (4 nm) parallel (perpendicular) to the a -axis, form a triangular vortex lattice (VL) under a small out-of-plane magnetic field. The invariance of vortex structures and VL under changes of field polarity and cooling history strongly supports time-reversal invariant superconductivity under zero field. At vortex cores (VCs), nonsplit, spectrally sharp zero-bias conductance peaks (ZBPs) persist up 8 T that are consistent with symmetry-protected Majorana zero modes (MZMs) in a topological vortex line. Close examination of vortex structures reveals a mirror-asymmetric doublet─one with ZBPs and another with an enhanced apparent gap, possibly originating from a field-induced multicomponent order parameter.

UTe2↗

DOE OSTI2023

Flow field characteristics of a 127-pin rod bundle with hexagonal spacer grids

A determination of nominal flow phenomena in liquid metal fast reactor (LMFR) fuel assemblies is critical toward generation-IV reactor development. Axially positioned spacer grids are used to maintain the geometry of hexagonal rod bundles and simultaneously introduce perturbations in the flow. Three-dimensional (3D) printed asymmetric honeycomb spacer grids were installed in a prototypical 127-pin LMFR fuel assembly model to study complex fluid dynamics interactions induced by the spacer grid and rods. To characterize flow dynamics in this intricate geometry, time-resolved particle image velocimetry (TR-PIV) using the matched-index-of-refraction method was employed to obtain non-intrusive velocity measurements for three axial planes (one near-wall and two interior planes) at a Reynolds number of 6000. The statistical TR-PIV results compared sub-channel-dependent normalized time-averaged velocity, velocity fluctuations, Reynolds stress, vorticity, and turbulence kinetic energy distributions. TR-PIV line profiles characterized downstream spacer grid flow dynamics. Two-point spatial and spatial–temporal cross-correlation fields revealed local coherent structures and quantified convection velocities of traveling vortices. Spatial–temporal decomposition using dynamic mode decomposition (DMD) applied to the near-wall vorticity fields extracted turbulent structures and flow instabilities in the wake region of the spacer grid, along with their decay and frequency rates. Reduced-order velocity fields from DMD reconstructions identified the most energy-containing coherent structures persistent in the near-wall region. This research provides experimental data sets and analyses of flow behavior in rod bundles with hexagonal spacer grids. In conclusion, the results are critical toward LMFR design and geometry optimization, crucial for the validation of computational fluid dynamics and reduced-order flow models.

42 ENGINEERING↗

DOE OSTI2025

Second harmonic Bessel-Gauss beam shaping with elliptic axicon aberrations

The second harmonic (SH) of an axicon generated Bessel-Gauss beam is created through the nonlinear interaction of photons with a crystal, resulting in the energy doubling of the output photons. In this work, we show experimentally that in addition to frequency doubling, the SH of Bessel-Gauss beams under asymmetric aberrations from an elliptic axicon exhibit intriguing beam formation. Particularly, the central region of the SH beam profile is composed of two central spots of various geometries surrounded by nested ellipses; one of which is the configuration of two central gamma dots with similar radius knotted by nested ellipses for a zeroth-order Bessel-Gauss pump. These SH beams consistently maintain their spatial profile throughout propagation, reminiscing the behavior of screw dislocations in wave patterns. Our numerical simulations produce beam dynamics consistent with that of experiments and further implicate the remarkable interweaving of bright spots with dark vortices. This is especially noticeable when the beams dynamically oscillate along the optical axis, resulting in the genesis of spatially polarized beams with a knotted framework. The insights gained from our study establish a novel paradigm for exploring interactions of Bessel-like beams with vortex dynamics. This, in turn, has the potential to spark innovations in optical applications, fostering new methodologies to harness and manipulate complex light structures. Our experimental findings could spur new methods of generating logical states of light and new opportunities for material processing control. Published by the American Physical Society 2025

Wang, Tianhong (ORCID:0000000169104201)↗

DOE OSTI2021

Reversible ratchet effects in a narrow superconducting ring

We study the ratchet effect in a narrow pinning-free superconductive ring based on time-dependent GinzburgLandau (TDGL) equations. Voltage responses to external dc and ac currents at various magnetic fields are studied. Due to asymmetric barriers for flux penetration and flux exit in the ring-shaped superconductor, the critical current above which the flux-flow state is reached, as well as the critical current for the transition to the normal state, are different for the two directions of applied current. Furthermore, these effects cooperatively cause ratchet signal reversal at high magnetic fields, which has not been reported to date in a pinning-free system. The ratchet signal found here is larger than those induced by asymmetric pinning potentials. Our results also demonstrate the feasibility of using mesoscopic superconductors to employ a superconducting diode effect in versatile superconducting devices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗