SEARCH · Search NASA

Results for “Boundary layer thickness”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

All sources NASA NTRS DOE OSTI

NASA NTRS2022

Semispan Test Results of a Conventional High-Lift Common Research Model in Landing Configuration

A 10%-scale high-lift version of the Common Research Model (CRM-HL) was tested in the 14- by 22-Foot Subsonic Tunnel at the NASA Langley Research Center. This research was aimed at providing a representative reference case for comparison with an Active Flow Control (AFC) enabled version of the CRM-HL and to increase the existing experimental database for CFD high-lift prediction. The test was conducted mostly at a freestream Mach number of 0.20. The effects of the engine nacelle, nacelle chine, tufts, small variations in Mach number, hysteresis-associated increasing/decreasing angle of attack, and incoming floor boundary-layer thickness (i.e., thinning by activation of the floor boundary layer removal system) were examined. A prestall lift performance degradation for the CRM-HL configuration was resolved with a properly placed nacelle chine. Surface pressure results are presented in detail for three key variants of CRM-HL — baseline (nacelle on), nacelle off, and nacelle with the most effective chine installation. The presented aerodynamic forces and surface pressures include both with and without the wall correction using the Transonic Wall Interference Correction System (TWICS) method. A limited set of photogrammetry results is also presented to document the model deformation under test conditions.

high-lift↗

NASA NTRSDate not supplied

Broadband Predictions of Optimized Proprotors in Axial Forward Flight

A low-fidelity toolchain was used to predict broadband self-noise trends for three proprotors in axial flight: a baseline (C24ND) and two acoustically constrained proprotors (OPT-III and COPR-3). Rotor loads were predicted with the ANOPP Propeller Analysis System (PAS) and self-noise was predicted with the semiempirical method of Brooks, Pope, and Marcolini (BPM) implemented in the ANOPP2 Self-Noise Internal Functional Module (ASNIFM). Comparisons to experimental data revealed that trends for turbulent boundary layer trailing edge (TBL-TE) noise could be modeled across several flight conditions by increasing the boundary layer thicknesses via the trip setting. Since the Mach number range of the BPM method is exceeded in these predictions, a dependence of boundary layer displacement thickness on blade station Mach number was suggested as a possible reason for needing to model thicker boundary layers, suggesting that the TBL-TE model needs to be developed further. Bluntness vortex shedding noise (BVS) predictions required tuning the trailing edge thickness and trailing edge closure angle for each flight condition to match experimental trends, demonstrating that the BVS noise model is incomplete and that BVS noise may vary with the angle of attack. This study indicates that the BPM self-noise method needs to be improved, which will lead to more accurate broadband predictions.

Broadband self-noise↗

NASA NTRSDate not supplied

Broadband Predictions of Optimized Proprotors in Axial Forward Flight

Broadband self-noise↗

NASA NTRS1977

Variable thickness shear layer aerodynamics revisited

The constant boundary-layer thickness (BLT) figuring in the Ventres (1975) Kernel function can be replaced by a slowly varying BLT, in the case of shear layers of slowly varying thickness. A simplification of the extension by Chi (1976) of Ventres' solution is put forward. The Kernel function in this instance relates pressure on the lifting surface to downwash over the surface. The results should also apply, formally, to three-dimensional compressible unsteady flows, but the accuracy in assuming slowly varying shear BLT remains to be determined. All variants of the shear layer model fail when the shear layer thickness varies rapidly.

Dowell, E. H.↗

NASA NTRS1987

The response of a compressible turbulent boundary layer to short regions of concave surface curvature

An experimental investigation of the supersonic flow of a boundary layer over short regions of concave surface curvature, using radii of curvature equivalent to 10 and 50 (models I and II, respectively) initial boundary layer thicknesses and 8-deg turning angle, notes that the boundary layer experienced a strong adverse pressure gradient as the boundary layer passed through the curved region. Attention is given to the mean and turbulent field for each flow, with comparisons of results to those for an 8-deg ramp. In the ramp and model I, turbulence levels increased significantly, together with structural parameters; in model II, despite an increase in turbulence levels, structural parameters remained essentially unchanged. The former results suggest that the perturbation is rapid, and describable in terms of total rather than local strains.

Jayaram, Mohan↗

NASA NTRS1989

Flow-induced morphological instabilities due to temporally-modulated stagnation-point flow

The influence of periodically-modulated planar stagnation-point flow on the morphological stability of a directionally-solidifying interface is presently considered with a view to the effect of unsteady nonparallel flows on single-crystal growth. The modeling of the system assumes that the viscous boundary layer thickness is much greater than that of the solute boundary layer, and that the modulation frequency is much smaller than the strength of plane stagnation-point flow. The solidifying interface is either stabilized or destabilized depending on the ratio of the period of modulation to the solute-diffusion time.

Merchant, G. J.↗

NASA NTRS1951

Theoretical Investigation of Submerged Inlets at Low Speeds

The general characteristics of the flow field in a submerged air inlet are investigated by theoretical, wind-tunnel, and visual-flow studies. Equations are developed for calculating the laminar and turbulent boundary-layer growth along the ramp floor for parallel, divergent, and convergent ramp walls, and a general equation is derived relating the boundary-layer pressure losses to the boundary-layer thickness. It is demonstrated that the growth of the boundary layer on the floor of the divergent-ramp inlet is retarded and that a vortex pair is generated in such an inlet. Functional relationships are established between the pressure losses in the vortices and the geometry of the inlet. A general discussion of the boundary layer and vortex formations is included, in which variations of the various losses and of the incremental external drag with mass-flow ratio are considered. Effects of compressibility are also discussed.

Sacks, Alvin H.↗

NASA NTRS1951

Investigation at Mach Number 1.88 of Half of a Conical-spike Diffuser Mounted as a Side Inlet with Boundary-layer Control / H. Fred Goelzer and Edgar M. Cortright, Jr

Experimental investigation was conducted at Mach number 1.88 to determine performance characteristics of half a 50 degree-conical-spike inlet mounted on a flat plate. Initial boundary layer was removed up-stream of inlet by a ram-type scoop of variable height. Initial boundary-layer thickness was also varied. With complete removal of initial boundary layer, total-pressure recovery of approximately 70 percent. Several alternative boundary-layer-removal systems were investigated which decreased the adverse effect of operating the ram scoop sub-critically.

BOUNDARY LAYER CONTROL-INTERNAL AERODYNAMICS↗

NASA NTRS1989

Treatment of singularities in cracked bodies

Three-dimensional finite-element analyses of middle-crack tension (M-T) and bend specimens subjected to mode I loadings were performed to study the stress singularity along the crack front. The specimen was modeled using 20-node isoparametric elements. The displacements and stresses from the analysis were used to estimate the power of singularities using a log-log regression analysis along the crack front. The analyses showed that finite-sized cracked bodies have two singular stress fields of the form rho = C sub o (theta, z) r to the -1/2 power + D sub o (theta, phi) R to the lambda rho power. The first term is the cylindrical singularity with the power -1/2 and is dominant over the middle 96 pct (for Poisson's ratio = 0.3) of the crack front and becomes nearly zero at the free surface. The second singularity is a vertex singularity with the vertex point located at the intersection of the crack front and the free surface. The second term is dominant at the free surface and becomes nearly zero away from the the boundary layer. The thickness of the boundary layer depends on Poisson's ratio of the material and is independent of the specimen type. The thickness of the boundary layer varied from 0 pct to about 5 pct of the total specimen thickness as Poisson's ratio varied from 0.0 to 0.45. Because there are two singular stress fields near the free surface, the strain energy release rate (G) is an appropriate parameter to measure the severity of the crack.

Shivakumar, K. N.↗

NASA NTRS1990

Treatment of singularities in cracked bodies

Three-dimensional finite-element analyses of middle-crack tension (M-T) and bend specimens subjected to mode I loadings were performed to study the stress singularity along the crack front. The specimen was modeled using 20-node isoparametric elements. The displacements and stresses from the analysis were used to estimate the power of singularities using a log-log regression analysis along the crack front. The analyses showed that finite-sized cracked bodies have two singular stress fields of the form rho = C sub o (theta, z) r to the -1/2 power + D sub o (theta, phi) R to the lambda rho power. The first term is the cylindrical singularity with the power -1/2 and is dominant over the middle 96 pct (for Poisson's ratio = 0.3) of the crack front and becomes nearly zero at the free surface. The second singularity is a vertex singularity with the vertex point located at the intersection of the crack front and the free surface. The second term is dominant at the free surface and becomes nearly zero away from the boundary layer. The thickness of the boundary layer depends on Poisson's ratio of the material and is independent of the specimen type. The thickness of the boundary layer varied from 0 pct to about 5 pct of the total specimen thickness as Poisson's ratio varied from 0.0 to 0.45. Because there are two singular stress fields near the free surface, the strain energy release rate (G) is an appropriate parameter to measure the severity of the crack.

Shivakumar, K. N.↗

NASA NTRS1980

On optical imaging through aircraft turbulent boundary layers

Optical resolution quality as affected by aircraft turbulent boundary layers is analyzed. Wind-tunnel data was analyzed to obtained the variation of boundary layer turbulence scale length and mass density rms fluctuations with Mach number. The data gave good agreement with a mass density fluctuation turbulence spectrum that is either isotropic of orthogonally anisotropic. The data did not match an isotropic turbulence velocity spectrum which causes an anisotropic non-orthogonal mass density fluctuation spectrum. The results indicate that the average mass density rms fluctuation is about 10% of the maximum mass density across the boundary layer and that the transverse turbulence scale size is about 10% of the boundary layer thickness. The results indicate that the effect of the turbulent boundary layer is large angle scattering which decreases contrast but not resolution. Using extinction as a criteria the range of acceptable aircraft operating conditions are given.

Sutton, G. W.↗

NASA NTRS1980

Wind tunnel investigation of the Titan Forward Skirt compartment vent from a free-stream Mach number of 0.80 to 1.96

A test was conducted to determine the flow characteristics of the Titan forward skirt compartment vent over a free stream Mach number range of 0.80 to 1.96. The vent was mounted in a flat plate and the plate was flush mounted to the tunnel side wall with coinciding center lines. Air was discharged from a duct, located on the tunnel side wall behind the plate, through a canted aft 30 deg honeycomb vent into the free stream. Data for the analysis of the Titan forward skirt compartment venting during ascent through the atmosphere are provided. Full scale simulated flight hardware, such as the honeycomb vent, duct corrugations and field joint ring were used. Boundary layer thicknesses were used to vary boundary height. The highest vent discharge coefficient for any given Mach number and vent pressure ratio generally occurred at the maximum displacement thickness. With no vent flow the static pressure in the vent region was generally less than the free stream static pressure. With vent flow, the static pressures upstream of the vent increased, and those downstream of the vent decreased.

Johns, A. L.↗

NASA NTRS2006

Optimal Control of Shock Wave Turbulent Boundary Layer Interactions Using Micro-Array Actuation

The intent of this study on micro-array flow control is to demonstrate the viability and economy of Response Surface Methodology (RSM) to determine optimal designs of micro-array actuation for controlling the shock wave turbulent boundary layer interactions within supersonic inlets and compare these concepts to conventional bleed performance. The term micro-array refers to micro-actuator arrays which have heights of 25 to 40 percent of the undisturbed supersonic boundary layer thickness. This study covers optimal control of shock wave turbulent boundary layer interactions using standard micro-vane, tapered micro-vane, and standard micro-ramp arrays at a free stream Mach number of 2.0. The effectiveness of the three micro-array devices was tested using a shock pressure rise induced by the 10 shock generator, which was sufficiently strong as to separate the turbulent supersonic boundary layer. The overall design purpose of the micro-arrays was to alter the properties of the supersonic boundary layer by introducing a cascade of counter-rotating micro-vortices in the near wall region. In this manner, the impact of the shock wave boundary layer (SWBL) interaction on the main flow field was minimized without boundary bleed.

Anderson, Bernhard H.↗

NASA NTRS1990

On the Goertler instability in hypersonic flows: Sutherland law fluids and real gas effects

The Goertler vortex instability mechanism in a hypersonic boundary layer on a curved wall is investigated. The precise roles of the effects of boundary layer growth, wall cooling, and gas dissociation is clarified in the determination of stability properties. It is first assumed that the fluid is an ideal gas with viscosity given by Sutherland's law. It is shown that when the free stream Mach number M is large, the boundary layer divides into two sublayers: a wall layer of O(M sup 3/2) thickness over which the basic state temperature is O(M squared) and a temperature adjustment layer of O(1) thickness over which the basic state temperature decreases monotonically to its free stream value. Goertler vortices which have wavelengths comparable with the boundary layer thickness are referred to as wall modes. It is shown that their downstream evolution is governed by a set of parabolic partial differential equations and that they have the usual features of Goertler vortices in incompressible boundary layers. As the local wavenumber increases, the neutral Goertler number decreases and the center of vortex activity moves towards the temperature adjustment layer. Goertler vortices with wavenumbers of order one or larger must necessarily be trapped in the temperature adjustment layer and it is this mode which is most dangerous. For this mode, it was found that the leading order term in the Goertler number expansion is independent of the wavenumber and is due to the curvature of the basic state. This term is also the asymptotic limit of the neutral Goertler numbers of the wall mode. To determine the higher order corrections terms in the Goertler number expansion, two wall curvature cases are distinguished. Real gas effects were investigated by assuming that the fluid is an ideal dissociating gas. It was found that both gas dissociation and wall cooling are destabilizing for the mode trapped in the temperature adjustment layer, but for the wall mode trapped near the wall the effect of gas dissociation can be either destabilizing or stabilizing.

Fu, Yibin B.↗

NASA NTRS1972

Characteristics of the unsteady shock-induced laminar boundary layer on a flat plate.

The unsteady shock-induced laminar boundary layer on a flat plate is theoretically studied for shock speeds ranging from 1.12 to 9 km/sec. Boundary layer flows for real air, assumed to be in thermochemical equilibrium, are analyzed by extending Lam's work on shock-induced laminar boundary layers to equilibrium dissociated and ionized flows. A complete description of the unsteady nature of the boundary layer is presented in terms of heat transfer and several boundary layer thickness quantities as functions of a single time-position variable. Boundary layer development is considered for two points of view. Time-dependent boundary layer development and approach to steady state for any fixed position on the plate is described, as is the configuration of the boundary layer with position on the plate at any point in time.

Cook, W. J.↗

NASA NTRS1980

Coherent substructure of turbulence near the stagnation zone of a bluff body

The evolution of freestream turbulence in crossflow about a circular cylinder was studied in order to identify the existence of a coherent substructure which is the outcome of the amplification of freesteam turbulence by the stretching mechanism in diverging flow about a bluff body. Visualization of the flow events revealed the selective stretching of cross-vortex tubes and the emergence of an organized turbulent flow pattern near the cylinder stagnation zone. Significant amplification of the total turbulent energy of the streamwise fluctuating velocity was consistently monitored. Realization of selective amplification at scales larger than the neutral scale of the stagnation flow was indicated by the variation of the discrete streamwise turbulent energy. A most amplified scale, characteristic of the energy containing eddies within the coherent substructure and commensurate with the boundary-layer thickness, was detected. Penetration of the amplified turbulence into the cylinder boundary layer led to the retardation of separation and to a concurrent decrease in the drag coefficient at subcritical cylinder-diameter Reynolds numbers.

Sadeh, W. Z.↗

NASA NTRS1989

An experimental study of near wall flow parameters in the blade end-wall corner region

The near wall flow parameters in the blade end-wall corner region is investigated. The blade end-wall corner region was simulated by mounting an airfoil section (NACA 65-015 base profile) symmetric blades on both sides of the flat plate with semi-circular leading edge. The initial 7 cm from the leading edge of the flat plate was roughened by gluing No. 4 floor sanding paper to artificially increase the boundary layer thickness on the flat plate. The initial flow conditions of the boundary layer upstream of the corner region are expected to dictate the behavior of flow inside the corner region. Therefore, an experimental investigation was extended to study the combined effect of initial roughness and increased level of free stream turbulence on the development of a 2-D turbulent boundary layer in the absence of the blade. The measurement techniques employed in the present investigation included, the conventional pitot and pitot-static probes, wall taps, the Preston tube, piezoresistive transducer and the normal sensor hot-wire probe. The pitot and pitot-static probes were used to obtain mean velocity profile measurements within the boundary layer. The measurements of mean surface static pressure were obtained with the surface static tube and the conventional wall tap method. The wall shear vector measurements were made with a specially constructed Preston tube. The flush mounted piezoresistive type pressure transducer were employed to measure the wall pressure fluctuation field. The velocity fluctuation measurements, used in obtaining the wall pressure-velocity correlation data, were made with normal single sensor hot-wire probe. At different streamwise stations, in the blade end-wall corner region, the mean values of surface static pressure varied more on the end-wall surface in the corner region were mainly caused by the changes in the curvature of the streamlines. The magnitude of the wall shear stress in the blade end-wall corner region increased significantly in the close vicinity of the corner line. The maximum value of the wall shear stress and its location from the corner line, on both the surfaces forming the corner region, were observed to change along the corner. These observed changes in the maximum values of the wall shear stress and its location from the corner line could be associated with the stretching and attenuation of the horseshoe vortex. The wall shear stress vectors in the blade end-wall corner region were observed to be more skewed on the end-wall surface as compared to that on the blade surface. The differences in the wall shear stress directions obtained with the Preston tube and flow visualization method were within the range in which the Preston tube was found to be insensitive to the yaw angle.

Bhargava, Rakesh K.↗

NASA NTRS1991

Evaluation of a technique to generate artificially thickened boundary layers in supersonic and hypersonic flows

The feasibility of using a contoured honeycomb model to generate a thick boundary layer in high-speed, compressible flow was investigated. The contour of the honeycomb was tailored to selectively remove momentum in a minimum of streamwise distance to create an artificially thickened turbulent boundary layer. Three wind tunnel experiments were conducted to verify the concept. Results indicate that this technique is a viable concept, especially for high-speed inlet testing applications. In addition, the compactness of the honeycomb boundary layer simulator allows relatively easy integration into existing wind tunnel model hardware.

Porro, A. R.↗