Search NASA⌕ Search

SEARCH · Search NASA

Results for “COMBUSTION PRODUCTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

Theoretical and Numerical Investigation of Radiative Extinction of Diffusion Flames

The influence of soot radiation on diffusion flames was investigated using both analytical and numerical techniques. Soot generated in diffusion flames dominate the flame radiation over gaseous combustion products and can significantly lower the temperature of the flame. In low gravity situations there can be significant accumulation of soot and combustion products in the vicinity of the primary reaction zone owing to the absence of any convective buoyant flow. Such situations may result in substantial suppression of chemical activities in a flame, and the possibility of a radiative extinction may also be anticipated. The purpose of this work was to not only investigate the possibility of radiative extinction of a diffusion flame but also to qualitatively and quantitatively analyze the influence of soot radiation on a diffusion flame. In this study, first a hypothetical radiative loss profile of the form of a sech(sup 2) was assumed to influence a pure diffusion flame. It was observed that the reaction zone can, under certain circumstances, move through the radiative loss zone and locate itself on the fuel side of the loss zone contrary to our initial postulate. On increasing the intensity and/or width of the loss zone it was possible to extinguish the flame, and extinction plots were generated. In the presence of a convective flow, however, the movement of the temperature and reaction rate peaks indicated that the flame behavior is more complicated compared to a pure diffusional flame. A comprehensive model of soot formation, oxidation and radiation was used in a more involved analysis. The soot model of Syed, Stewart and Moss was used for soot nucleation and growth and the model of Nagle and Strickland-Constable was used for soot oxidation. The soot radiation was considered in the optically thin limit. An analysis of the flame structure revealed that the radiative loss term is countered both by the reaction term and the diffusion term. The essential balance for the soot volume fraction was found to be between the processes of soot convection and soot growth. Such a balance yielded to analytical treatment and the soot volume fraction could be expressed in the form of an integral. The integral was evaluated using two approximate methods and the results agreed very well with the numerical solutions for all cases examined.

Ray, Anjan↗

Direct heating surface combustor

The combustor utilizes a non-adiabatic flame to provide low-emission combustion for gas turbines. A fuel-air mixture is directed through a porous wall, the other side of which serves as a combustion surface. A radiant heat sink disposed adjacent to and spaced from the combustion surface controls the combustor flame temperature in order to prevent the formation of oxides of nitrogen. A secondary air flow cools the heat sink. Additionally, up to 100% of secondary air flow is mixed with the combustion products at the direct heating surface combustor to dilute such products thereby reducing exit temperature. However, if less than 100% secondary air is mixed to the combustor, the remainder may be added to the combustion products further downstream.

Beremand, D. G.↗

Calculation of eddy viscosity in a compressible turbulent boundary layer with mass injection and chemical reaction, volume 1

The turbulent kinetic energy equation is coupled with boundary layer equations to solve the characteristics of compressible turbulent boundary layers with mass injection and combustion. The Reynolds stress is related to the turbulent kinetic energy using the Prandtl-Wieghardt formulation. When a lean mixture of hydrogen and nitrogen is injected through a porous plate into the subsonic turbulent boundary layer of air flow and ignited by external means, the turbulent kinetic energy increases twice as much as that of noncombusting flow with the same mass injection rate of nitrogen. The magnitudes of eddy viscosity between combusting and noncombusting flows with injection, however, are almost the same due to temperature effects, while the distributions are different. The velocity profiles are significantly affected by combustion; that is, combustion alters the velocity profile as if the mass injection rate is increased, reducing the skin-friction as a result of a smaller velocity gradient at the wall. If pure hydrogen as a transpiration coolant is injected into a rocket nozzle boundary layer flow of combustion products, the temperature drops significantly across the boundary layer due to the high heat capacity of hydrogen. At a certain distance from the wall, hydrogen reacts with the combustion products, liberating an extensive amount of heat. The resulting large increase in temperature reduces the eddy viscosity in this region.

Omori, S.↗

Calculation of eddy viscosity in a compressible turbulent boundary layer with mass injection and chemical reaction

The turbulent kinetic energy equation is coupled with boundary layer equations to solve the characteristics of compressible turbulent boundary layers with mass injection and combustion. The Reynolds stress is related to the turbulent kinetic energy using the Prandtl-Wieghardt formulation. When a lean mixture of hydrogen and nitrogen is injected through a porous plate into the subsonic turbulent boundary layer of air flow and ignited by external means, the turbulent kinetic energy increases twice as much as that of noncombusting flow with the same mass injection rate of nitrogen. The magnitudes of eddy viscosity between combusting and noncombusting flows with injection, however, are almost the same due to temperature effects, while the distributions are different. The velocity profiles are significantly affected by combustion. If pure hydrogen as a transpiration coolant is injected into a rocket nozzle boundary layer flow of combustion products, the temperature drops significantly across the boundary layer due to the high heat capacity of hydrogen. At a certain distance from the wall hydrogen reacts with the combustion products, liberating an extensive amount of heat.

Omori, S.↗

Full-scale aircraft cabin flammability tests of improved fire-resistant materials

Full-scale aircraft cabin flammability tests to evaluate the effectiveness of new fire-resistant materials by comparing their burning characteristics with those of older aircraft materials are described. Three tests were conducted and are detailed. Test 1, using pre-1968 materials, was run to correlate the procedures and to compare the results with previous tests by other organizations. Test 2 included newer, improved fire-resistant materials. Test 3 was essentially a duplicate of test 2, but a smokeless fuel was used. Test objectives, methods, materials, and results are presented and discussed. Results indicate that the pre-1968 materials ignited easily, allowed the fire to spread, produced large amounts of smoke and toxic combustion products, and resulted in a flash fire and major fire damage. The newer fire-resistant materials did not allow the fire to spread. Furthermore, they produced less, lower concentrations of toxic combustion products, and lower temperatures. The newer materials did not produce a flash fire.

Stuckey, R. N.↗

Numerical Investigation of the Effect of Cooling Airflow inside High-Pressure Turbine using the Source Term Approach

In this study, the Open National Combustion code (OpenNCC) is applied to simulate the airflow inside the high-pressure turbine (HPT) of the energy efficient engine (EEE). The main objective of this study is to compare the characteristics of the HPT performance obtained by using three different approaches (Case 1: the realistic combustion products are considered at the HPT inlet, but the cooling airflows are not included, Case 2: the working fluid is assumed to be a single gas (i.e., air), and the cooling airflows are considered, Case 3: the cooling airflow and the combustion products at the HPT inlet are included). To mimic the cooling airflows at the HPT surface, we use the surface source team approach, in which we impose the source term at a specific area of a cooling airflow hole at the solid surfaces by specifying an injection angle, temperature, turbulent intensity, and mass flowrate of each cooling airflow. For the validation of the model, the data for the EEE model was obtained from the General Electric (GE) test campaign (RDG10), and the full scale warm-air rig test condition representing a test point close to the integrated core/low spool design condition was considered. This validation test was done using the stationary uniform inflow condition (i.e., the reported total temperature and total pressure). Secondly, we considered the Sea-Level Take-off (SLTO) engine condition and separately performed the combustor simulation to obtain a more realistic time-averaged, spatially-nonuniform HPT inflow condition. This work provides a better understanding the effect of the cooling airflow model with different assumptions on the HPT performance. It is found that using different working gas have a minor effect on the performance metric, however the presence of the cooling airflows significantly affects the HPT performance such as the turbine efficiency.

CFD Hot-streaks↗

Real-Time X-ray Radiography Diagnostics of Components in Solid Rocket Motors

Solid rocket motors (SRMs) typically use nozzle materials which are required to maintain their shape as well as insulate the underlying support structure during the motor operation. In addition, SRMs need internal insulation materials to protect the motor case from the harsh environment resulting from the combustion of solid propellant. In the nozzle, typical materials consist of high density graphite, carbon-carbon composites and carbon phenolic composites. Internal insulation of the motor cases is typically a composite material with carbon, asbestos, Kevlar, or silica fibers in an ablative matrix such as EPDM or NBR. For both nozzle and internal insulation materials, the charring process occurs when the hot combustion products heat the material intensely. The pyrolysis of the matrix material takes away a portion of the thermal energy near the wall surface and leaves behind a char layer. The fiber reinforcement retains the porous char layer which provides continued thermal protection from the hot combustion products. It is of great interest to characterize both the total erosion rates of the material and the char layer thickness. By better understanding of the erosion process for a particular ablative material in a specific flow environment, the required insulation material thickness can be properly selected. The recession rates of internal insulation and nozzle materials of SRMs are typically determined by testing in some sort of simulated environment; either arc-jet testing, flame torch testing, or subscale SRMs of different size. Material recession rates are deduced by comparison of pre- and post-test measurements and then averaging over the duration of the test. However, these averaging techniques cannot be used to determine the instantaneous recession rates of the material. Knowledge of the variation in recession rates in response to the instantaneous flow conditions during the motor operation is of great importance. For example, in many SRM configurations the recession of the solid propellant grain can drastically alter the flow-field and effect the recession of internal insulation and nozzle materials. Simultaneous measurement of the overall erosion rate, the development of the char layer, and the recession of the char-virgin interface during the motor operation can be rather difficult. While invasive techniques have been used with limited success, they have serious drawbacks. Break wires or make wire sensors can be installed into a sufficient number of locations in the charring material from which a time history of the charring surface can be deduced. These sensors fundamentally alter the local structure of the material in which they are imbedded. Also, the location of these sensors within the material is not known precisely without the use of an X-ray. To determine instantaneous recession rates, real-time X-ray radiography (X-ray RTR) has been utilized in several SRM experiments at PSU. The X-ray RTR system discussed in this paper consists of an X-ray source, X-ray image intensifier, and CCD camera connected to a capture computer. The system has been used to examine the ablation process of internal insulation as well as nozzle material erosion in a subscale SRM. The X-ray source is rated to 320 kV at 10 mA and has both a large (5.5 mm) and small (3.0 mm) focal spot. The lead-lined cesium iodide X-ray image intensifier produces an image which is captured by a CCD camera with a 1,000 x 1,000 pixel resolution. To produce accurate imagery of the object of interest, the alignment of the X-ray source to the X-ray image intensifier is crucial. The image sequences captured during the operation of an SRM are then processed to enhance the quality of the images. This procedure allows for computer software to extract data on the total erosion rate and the char layer thickness. Figure 1 Error! Reference source not found.shows a sequence of images captured during the operation the subscale SRM with the X-ray RTR system. The X-rayTR system, alignment procedure, uncertainty determination, and image analysis process will be discussed in detail in the full manuscript.

Cortopassi, A. C.↗

A theoretical evaluation of aluminum gel propellant two-phase flow losses on vehicle performance

A one-dimensional model of a hydrocarbon/Al/O2(gaseous) fueled rocket combustion chamber was developed to study secondary atomization effects on propellant combustion. This chamber model was coupled with a two dimensional, two-phase flow nozzle code to estimate the two-phase flow losses associated with solid combustion products. Results indicate that moderate secondary atomization significantly reduces propellant burnout distance and Al2O3 particle size; however, secondary atomization provides only moderate decreases in two-phase flow induced I(sub sp) losses. Despite these two-phase flow losses, a simple mission study indicates that aluminum gel propellants may permit a greater maximum payload than the hydrocarbon/O2 bi-propellant combination for a vehicle of fixed propellant volume. Secondary atomization was also found to reduce radiation losses from the solid combustion products to the chamber walls, primarily through reductions in propellant burnout distance.

Mueller, Donn C.↗

Computational method to predict thermodynamic, transport, and flow properties for the modified Langley 8-foot high-temperature tunnel

The Langley 8 foot high temperature tunnel (8 ft HTT) is used to test components of hypersonic vehicles for aerothermal loads definition and structural component verification. The test medium of the 8 ft HTT is obtained by burning a mixture of methane and air under high pressure; the combustion products are expanded through an axisymmetric conical contoured nozzle to simulate atmospheric flight at Mach 7. This facility was modified to raise the oxygen content of the test medium to match that of air and to include Mach 4 and Mach 5 capabilities. These modifications will facilitate the testing of hypersonic air breathing propulsion systems for a wide range of flight conditions. A computational method to predict the thermodynamic, transport, and flow properties of the equilibrium chemically reacting oxygen enriched methane-air combustion products was implemented in a computer code. This code calculates the fuel, air, and oxygen mass flow rates and test section flow properties for Mach 7, 5, and 4 nozzle configurations for given combustor and mixer conditions. Salient features of the 8 ft HTT are described, and some of the predicted tunnel operational characteristics are presented in the carpet plots to assist users in preparing test plans.

Venkateswaran, S.↗

Chemical Kinetics Underlying the Sooting Tendency and Auto-Ignition Characteristics of Linear, Branched, and Cyclic Ether Compounds

Biofuels present opportunities for improving the performance and reducing emissions from internal combustion engines by incorporating oxygenated functional groups to the fuels. Among various oxygenates, ethers have been recognized as promising candidates for an alternative to conventional diesel fuel owing to their higher reactivity and lower sooting tendency. The detailed guidelines for designing ethers, however, have not been fully discussed, even though their combustion characteristics are sensitive to the molecular structure. This study was devoted to exploring the structure-property relationships, particularly focusing on the cetane number and yield sooting index, using five linear, branched, and cyclic ethers: di-amyl-ether, 4-butoxy-heptane, 3,3-dimethyl-oxetane, 2-ethyl-4-methyl-1,3-dioxolane, and 2-isopropyl-4-methyl-1,3-dioxolane. First, we examined the chemical kinetics underlying the sooting tendency of the test fuels. The combustion product distribution was measured from flow reactor experiments at 750-1100 K, F=3, at atmospheric pressure. As a result, it was revealed that the sooting tendency is closely related to the size of hydrocarbon intermediates in the high-temperature regime (>1000 K); that is, larger hydrocarbons lead to more soot precursor formation. The underlying chemistry determining the size of the hydrocarbons from the tested fuels was analyzed using reaction pathway analysis and quantum mechanics calculations, which showed that the branched and cyclic ether structures form abundant C3-C4 compounds. Moreover, the auto-ignition characteristics of the test fuels were studied using the flow reactor at low-temperature (400-700 K) and F=1. We found a clear difference in the combustion-product distribution from high and low reactivity fuels, which was then correlated to the systematic analysis of the key reaction energy barriers with the varying molecular structure.

BIOMASS FUELS,INORGANIC, ORGANIC, PHYSICAL, AND AN↗

Variable-temperature cryogenic trap for the separation of gas mixtures

The paper describes a continuous variable-temperature U-shaped cold trap which can both purify vacuum-line combustion products for subsequent stable isotopic analysis and isolate the methane and ethane constituents of natural gases. The canister containing the trap is submerged in liquid nitrogen, and, as the gas cools, the gas mixture components condense sequentially according to their relative vapor pressures. After the about 12 min required for the bottom of the trap to reach the liquid-nitrogen temperature, passage of electric current through the resistance wire wrapped around the tubing covering the U-trap permits distillation of successive gas components at optimal temperatures. Data on the separation achieved for two mixtures, the first being typical vacuum-line combustion products of geochemical samples such as rocks and the second being natural gas, are presented, and the thermal behavior and power consumption are reported.

Des Marais, D. J.↗

An Experimental and Theoretical Study of Radiative Extinction of Diffusion Flames

In a recent paper on 'Observations of candle flames under various atmospheres in microgravity' by Ross et al., it was found that for the same atmosphere, the burning rate per unit wick surface area and the flame temperature were considerably reduced in microgravity as compared with normal gravity. Also, the flame (spherical in microgravity) was much thicker and further removed from the wick. It thus appears that the flame becomes 'weaker' in microgravity due to the absence of buoyancy generated flow which serves to transport the oxidizer to the combustion zone and remove the hot combustion products from it. The buoyant flow, which may be characterized by the strain rate, assists the diffusion process to execute these essential functions for the survival of the flame. Thus, the diffusion flame is 'weak' at very low strain rates and as the strain rate increases the flame is initially 'strengthened' and eventually it may be 'blown out'. The computed flammability boundaries of T'ien show that such a reversal in material flammability occurs at strain rates around 5 sec. At very low or zero strain rates, flame radiation is expected to considerably affect this 'weak' diffusion flame because: (1) the concentration of combustion products which participate in gas radiation is high in the flame zone; and (2) low strain rates provide sufficient residence time for substantial amounts of soot to form which is usually responsible for a major portion of the radiative heat loss. We anticipate that flame radiation will eventually extinguish this flame. Thus, the objective of this project is to perform an experimental and theoretical investigation of radiation-induced extinction of diffusion flames under microgravity conditions. This is important for spacecraft fire safety.

Atreya, Arvind↗

Experimental studies of the formation/deposition of sodium sulfate in/from combustion gases

An optical polarization (ellipsometric) technique was developed for measuring rapidly growing and evaporating transparent liquid condensate films (e.g., boric oxide) on solid surfaces exposed to combustion product gases. Results for the B2O3 deposition rate from BCl3-seeded propane/air flames are shown to agree well with the results of earlier interference measurements, and also with theoretical CVD predictions. Evaporation rates (from platinum ribbons into seeded propane air flames) are estimated using the polarization technique. It appears that, compared with the interference method, the polarization technique places less stringent requirements on surface quality, which may justify the added optical components needed for such measurements. It is concluded that the complementary optical methods of polarization (ellipsometry) and interference hold considerable promise for application to the rapid measurement of condensation and evaporation rates in high temperature (e.g., combustion product) environments.

Rosner, D. E.↗

A Computational Study of Plume Modeling for Space Launch System Abort Scenarios

A series of viscous CFD simulations depicting Space Launch System (SLS) post Mode-1abort scenarios are conducted and analyzed. The primary purpose of these simulations is to study the effect of launch abort vehicle attitude control motor (ACM) and abort motor(AM) plume modeling fidelity on the drag of the aborted core stage. The simulations are first conducted with a fully-coupled, multi-species and chemically reacting model for the freestream gases and the solid rocket abort motor combustion products. Following this, equivalent species are created for the ACM and AM exhaust gases. These equivalent species aim to provide near the same results for core stage drag as the chemically reacting model at a significantly lower computational cost. Finally, the exhaust gases are modeled as calorically perfect air. It was concluded that under most scenarios, both the equivalent species and the perfect air models predict the drag of the aborted core stage sufficiently close to that predicted by the chemically reacting simulations. In these cases, the flow and geometry conditions did not induce significant changes in the composition of the ‘true’ exhaust gas via afterburning of the combustion products. For cases where this was not the case, the properties of the essentially frozen equivalent species and perfect air models deviated from the true mixture, yielding unsatisfactory results. Finally, the accuracy improvements by using the chemically reacting model are weighed against the significant increase in associated computational costs. It was found that the simplified exhaust gas models are at least 4 times less expensive than the chemically reacting model. This may justify the judicious use of these simple models in future work.

CFD↗

A Computational Study of Plume Modeling for Space Launch System Abort Scenarios

A series of viscous CFD simulations depicting Space Launch System (SLS) post Mode-1abort scenarios are conducted and analyzed. The primary purpose of these simulations is to study the effect of launch abort vehicle attitude control motor (ACM) and abort motor(AM) plume modeling fidelity on the drag of the aborted core stage. The simulations are first conducted with a fully-coupled, multi-species and chemically reacting model for the freestream gases and the solid rocket abort motor combustion products. Following this, equivalent species are created for the ACM and AM exhaust gases. These equivalent species aim to provide near the same results for core stage drag as the chemically reacting model at a significantly lower computational cost. Finally, the exhaust gases are modeled as calorically perfect air. It was concluded that under most scenarios, both the equivalent species and the perfect air models predict the drag of the aborted core stage sufficiently close to that predicted by the chemically reacting simulations. In these cases, the flow and geometry conditions did not induce significant changes in the composition of the ‘true’ exhaust gas via afterburning of the combustion products. For cases where this was not the case, the properties of the essentially frozen equivalent species and perfect air models deviated from the true mixture, yielding unsatisfactory results. Finally, the accuracy improvements by using the chemically reacting model are weighed against the significant increase in associated computational costs. It was found that the simplified exhaust gas models are at least 4 times less expensive than the chemically reacting model. This may justify the judicious use of these simple models in future work.

CFD↗

Optical Multi-Gas Monitor Technology Demonstration on the International Space Station

The International Space Station (ISS) employs a suite of portable and permanently located gas monitors to insure crew health and safety. These sensors are tasked with functions ranging from fixed mass spectrometer based major constituents analysis to portable electrochemical sensor based combustion product monitoring. An all optical multigas sensor is being developed that can provide the specificity of a mass spectrometer with the portability of an electrochemical cell. The technology, developed under the Small Business Innovation Research program, allows for an architecture that is rugged, compact and low power. A four gas version called the Multi-Gas Monitor was launched to ISS in November 2013 aboard Soyuz and activated in February 2014. The portable instrument is comprised of a major constituents analyzer (water vapor, carbon dioxide, oxygen) and high dynamic range real-time ammonia sensor. All species are sensed inside the same enhanced path length optical cell with a separate vertical cavity surface emitting laser (VCSEL) targeted at each species. The prototype is controlled digitally with a field-programmable gate array/microcontroller architecture. The optical and electronic approaches are designed for scalability and future versions could add three important acid gases and carbon monoxide combustion product gases to the four species already sensed. Results obtained to date from the technology demonstration on ISS are presented and discussed.

Pilgrim, Jeffrey S.↗

Atomic Layer Deposition with TiO2 for Enhanced Reactivity and Stability of Aromatic Hydrogenation Catalysts

Hydrogenation of aromatic molecules in fossil- and bio-derived fuels is essential for decreasing emissions of harmful combustion products and addressing growing concerns around urban air pollution. In this work, we used atomic layer deposition to significantly enhance the hydrogenation performance of a conventional supported Pd catalyst by applying an ultrathin coating of TiO2 in a scalable powder coating process. The TiO2-coated catalyst showed substantial gains in the conversion of multiple aromatic molecules, including a 5-fold improvement in turnover frequency versus the uncoated catalyst in the hydrogenation of naphthalene. This activity enhancement was maintained upon scaling the coating synthesis process from 3 to 100 g. Based on the results from Xray photoelectron spectroscopy, X-ray absorption spectroscopy, and computational modeling, the activity enhancement was attributed to ensemble effects resulting from partial TiO2 coverage of the Pd surface rather than fundamental changes to the Pd electronic structure. Additional durability testing confirmed that the TiO2 coating improved the thermal and hydrothermal stability of the catalyst as well as tolerance toward sulfur impurities in the reactant stream. Using an economic model of an industrial deep hydrogenation process, we found that an increase in catalyst activity or lifetime of 2× would justify even a relatively high estimate for the cost of TiO2 atomic layer deposition coatings at scale

atomic layer↗