Search NASA⌕ Search

SEARCH · Search NASA

Results for “CONTROL SURFACES - HINGE MOMENTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS2013

An Overview of Modifications Applied to a Turbulence Response Analysis Method for Flexible Aircraft Configurations

A software program and associated methodology to study gust loading on aircraft exists for a classification of geometrically simplified flexible configurations. This program consists of a simple aircraft response model with two rigid and three flexible symmetric degrees of freedom and allows for the calculation of various airplane responses due to a discrete one-minus-cosine gust as well as continuous turbulence. Simplifications, assumptions, and opportunities for potential improvements pertaining to the existing software program are first identified, then a revised version of the original software tool is developed with improved methodology to include more complex geometries, additional excitation cases, and output data so as to provide a more useful and accurate tool for gust load analysis. Revisions are made in the categories of aircraft geometry, computation of aerodynamic forces and moments, and implementation of horizontal tail mode shapes. In order to improve the original software program to enhance usefulness, a wing control surface and horizontal tail control surface is added, an extended application of the discrete one-minus-cosine gust input is employed, a supplemental continuous turbulence spectrum is implemented, and a capability to animate the total vehicle deformation response to gust inputs in included. These revisions and enhancements are implemented and an analysis of the results is used to validate the modifications.

Funk, Christie J.↗
NASA NTRS1961

Effects of Mass-Loading Variations and Applied Moments on Motion and Control of a Manned Rotating Space Vehicle

An analytical study has been made to determine the effects of mass-loading variations and onboard rotating machinery on a hypothetical earth-satellite space station, rotating to provide an artificial gravity equal to one-fourth of that at the earth's surface. Attempts were also made to damp out or minimize undesirable motions by using mass shifts, constant-rate inertia wheels, or jet-reaction moments. Results obtained indicate that the shifting of masses within the rotating space station could bring about large roll oscillations (plus or minus 100 degrees) or even continuous rolling motions if the craft is rotating about the axis of intermediate moment of inertia. The pitch angles obtained were generally small (less than plus or minus 1 degree). The amplitudes of the roll and pitch oscillations are dependent upon the angle of displacement of the greatest principal axis of inertia from the initial spin axis. In attempting to damp out or minimize undesirable motions, it was found that a constant-rate inertia wheel located on and rotating about the axis about which the craft is rotating (Z-axis) was beneficial in keeping the roll angles relatively small, provided it had a sufficient amount of angular momentum. It was also found that the use of jet-reaction moments was very satisfactory for damping undesirable motions in that the roll oscillations could be damped.

Grantham, William D.↗
NASA NTRS1983

Interference effects of aft reaction-control yaw jets on the aerodynamic characteristics of a space shuttle orbiter model at supersonic speeds

A wind tunnel investigation of the interference effects of aft reaction control system yaw jet plumes on a 0.0125 scale Space Shuttle orbiter model was conducted at Mach numbers from 2.50 to 4.50. Test variables included model angle of attack, model angle of sideslip, jet to free stream mass flow ratio, and number and position of operating jets. The aft reaction control jet plume creates a blockage above and behind the wing on the side in which the jet exhausts and results in flow separation on the wing upper surface and fuselage side. Positive pitching moment and side force increments and negative yawing moment and rolling moment increments due to the flow separations are incurred for left side firing jets, primarily at angles of attack above 10 deg. The yawing moment interference increments are favorable and result in a small jet thrust amplification. As a result of this investigation, the aft reaction control system was certified for operation at supersonic Mach numbers prior to the first flight of the space transportation system (STS-1).

Covell, P. F.↗
NASA NTRS1981

A program to evaluate a control system based on feedback of aerodynamic pressure differentials

The use of aerodynamic pressure differentials to position a control surface is evaluated. The system is a differential pressure command loop, analogous to a position command loop, where the surface is commanded to move until a desired differential pressure across the surface is achieved. This type of control is more direct and accurate because it is the differential pressure which causes the control forces and moments. A frequency response test was performed in a low speed wind tunnel to measure the performance of the system. Both pressure and position feedback were tested. The pressure feedback performed as well as position feedback implying that the actuator, with a break frequency on the order of 10 Rad/sec, was the limiting component. Theoretical considerations indicate that aerodynamic lags will not appear below frequencies of 50 Rad/sec, or higher.

Levy, D. W.↗
NASA NTRS1994

A simple analytical aerodynamic model of Langley Winged-Cone Aerospace Plane concept

A simple three DOF analytical aerodynamic model of the Langley Winged-Coned Aerospace Plane concept is presented in a form suitable for simulation, trajectory optimization, and guidance and control studies. The analytical model is especially suitable for methods based on variational calculus. Analytical expressions are presented for lift, drag, and pitching moment coefficients from subsonic to hypersonic Mach numbers and angles of attack up to +/- 20 deg. This analytical model has break points at Mach numbers of 1.0, 1.4, 4.0, and 6.0. Across these Mach number break points, the lift, drag, and pitching moment coefficients are made continuous but their derivatives are not. There are no break points in angle of attack. The effect of control surface deflection is not considered. The present analytical model compares well with the APAS calculations and wind tunnel test data for most angles of attack and Mach numbers.

Pamadi, Bandu N.↗
NASA NTRSDate not supplied

High Reynolds Number Testing of the NATO AVT-298 SWiFT Configuration at the National Transonic Facility

A high Reynolds number wind tunnel test of the NATO AVT-298 Swept Wing Flow Test (SWiFT) configuration was conducted in the National Transonic Facility at the NASA Langley Research Center during the summer of 2023. The SWiFT research model geometry has relevance to both blended/hybrid wing body (BWB/HWB) and unmanned combat aerial vehicle (UCAV) configurations, and the test campaign was the culmination of an international collaboration under the NATO AVT-298 research task group. The main objectives of the test were to investigate Reynolds number scaling effects on low-speed stability & control characteristics and to examine the onset and progression of flow separation on the wings particularly near the wing crank. Force & moment and surface pressure data were acquired at Mach numbers from 0.2 to 0.8, Reynolds numbers from 2.5 to 34 million, angles of attack from -3 to 20 degrees, and sideslip angles from -10 to 10 degrees. Boundary layer transition detection techniques utilizing static pressure taps, unsteady pressure transducers, and sublimating chemicals were used on the model in a free/natural transition state or a forced transition state using trip dots. Pressure sensitive paint was used to obtain a global surface pressure profile on the model and an advanced laser velocimetry technique was used to obtain velocity measurements in the wake downstream of the wing crank. The results from the test showed clear Reynolds number scaling effects on the maximum lift coefficient and pitching moment coefficient at Mach 0.2, while also capturing significant hysteresis effects. The data acquired from the test will ultimately help improve computational aerodynamic analysis and design tools for application to future BWB-type vehicle configurations.

NATO AVT-298↗
NASA NTRSDate not supplied

High Reynolds Number Testing of the NATO AVT-298 SWiFT Configuration at the National Transonic Facility

A high Reynolds number wind tunnel test of the NATO AVT-298 Swept Wing Flow Test (SWiFT) configuration was conducted in the National Transonic Facility at the NASA Langley Research Center during the summer of 2023. The SWiFT research model geometry has relevance to both blended/hybrid wing body (BWB/HWB) and unmanned combat aerial vehicle (UCAV) configurations, and the test campaign was the culmination of an international collaboration under the NATO AVT-298 research task group. The main objectives of the test were to investigate Reynolds number scaling effects on low-speed stability & control characteristics and to examine the onset and progression of flow separation on the wings particularly near the wing crank. Force & moment and surface pressure data were acquired at Mach numbers from 0.2 to 0.8, Reynolds numbers from 2.5 to 34 million, angles of attack from -3 to 20 degrees, and sideslip angles from -10 to 10 degrees. Boundary layer transition detection techniques utilizing static pressure taps, unsteady pressure transducers, and sublimating chemicals were used on the model in a free/natural transition state or a forced transition state using trip dots. Pressure sensitive paint was used to obtain a global surface pressure profile on the model and an advanced laser velocimetry technique was used to obtain velocity measurements in the wake downstream of the wing crank. The results from the test showed clear Reynolds number scaling effects on the maximum lift coefficient and pitching moment coefficient at Mach 0.2, while also capturing significant hysteresis effects. The data acquired from the test will ultimately help improve computational aerodynamic analysis and design tools for application to future BWB-type vehicle configurations.

BWB/HWB↗
NASA NTRS1953

Rocket-Model Investigation of the Longitudinal Stability, Drag, and Duct Performance Characteristics of the North American MX-770 (X-10) Missile at Mach Numbers from 0.80 to 1.70

A free-flight 0.12-scale rocket-boosted model of the North American MX-770 (X-10) missile has been tested in flight by the Pilotless Aircraft Research Division of the Langley Aeronautical Laboratory. Drag, longitudinal stability, and duct performance data were obtained at Mach numbers from 0.8 to 1.7 covering a Reynolds number range of about 9 x 10(exp 6) to 24 x 10(exp 6) based on wing mean aerodynamic chord. The lift-curve slope, static stability, and damping-in-pitch derivatives showed similar variations with Mach number, the parameters increasing from subsonic values in the transonic region and decreasing in the supersonic region. The variations were for the most part fairly smooth. The aerodynamic center of the configuration shifted rearward in the transonic region and moved forward gradually in the supersonic region. The pitching effectiveness of the canard control surfaces was maintained throughout the flight speed range, the supersonic values being somewhat greater than the subsonic. Trim values of angle of attack and lift coefficient changed abruptly in the transonic region, the change being associated with variations in the out-of-trim pitching moment, control effectiveness, and aerodynamic-center travel in this speed range. Duct total-pressure recovery decreased with increase in free-stream Mach number and the values were somewhat less than normal-shock recovery. Minimum drag data indicated a supersonic drag coefficient about twice the subsonic drag coefficient and a drag-rise Mach number of approximately 0.90. Base drag was small subsonically but was about 25 percent of the minimum drag of the configuration supersonically.

Bond, Aleck C.↗
NASA NTRS2009

Orion Service Module Reaction Control System Plume Impingement Analysis Using PLIMP/RAMP2

The Orion Crew Exploration Vehicle Service Module Reaction Control System engine plume impingement was computed using the plume impingement program (PLIMP). PLIMP uses the plume solution from RAMP2, which is the refined version of the reacting and multiphase program (RAMP) code. The heating rate and pressure (force and moment) on surfaces or components of the Service Module were computed. The RAMP2 solution of the flow field inside the engine and the plume was compared with those computed using GASP, a computational fluid dynamics code, showing reasonable agreement. The computed heating rate and pressure using PLIMP were compared with the Reaction Control System plume model (RPM) solution and the plume impingement dynamics (PIDYN) solution. RPM uses the GASP-based plume solution, whereas PIDYN uses the SCARF plume solution. Three sets of the heating rate and pressure solutions agree well. Further thermal analysis on the avionic ring of the Service Module showed that thermal protection is necessary because of significant heating from the plume.

Wang, Xiao-Yen J.↗
NASA NTRS2009

Orion Service Module Reaction Control System Plume Impingement Analysis Using PLIMP/RAMP2

The Orion Crew Exploration Vehicle Service Module Reaction Control System engine plume impingement was computed using the plume impingement program (PLIMP). PLIMP uses the plume solution from RAMP2, which is the refined version of the reacting and multiphase program (RAMP) code. The heating rate and pressure (force and moment) on surfaces or components of the Service Module were computed. The RAMP2 solution of the flow field inside the engine and the plume was compared with those computed using GASP, a computational fluid dynamics code, showing reasonable agreement. The computed heating rate and pressure using PLIMP were compared with the Reaction Control System plume model (RPM) solution and the plume impingement dynamics (PIDYN) solution. RPM uses the GASP-based plume solution, whereas PIDYN uses the SCARF plume solution. Three sets of the heating rate and pressure solutions agree well. Further thermal analysis on the avionic ring of the Service Module was performed using MSC Patran/Pthermal. The obtained temperature results showed that thermal protection is necessary because of significant heating from the plume.

Wang, Xiao-Yen↗
NASA NTRS1975

Drogue parachute deployment dynamics of the space shuttle solid rocket booster

Theoretical analysis and experimental investigations are presented for two deployment concepts of the drogue parachute deployment for the space shuttle solid rocket booster. The analysis represents the motion of three coupled rigid bodies, with one of the bodies having variable mass and moment of inertia. The unfurling process of the parachute from the bag is idealized as the flow of a continuum out of a control surface. The pilot parachute or tethered nose cap is modeled as a flexible pendulum with a nonlinear spring and a moving support. Measured wind tunnel test data compare reasonably well with the theory.

Banerjee, A. K.↗
NASA NTRS1997

Vortex leading edge flap assembly for supersonic airplanes

A leading edge flap (16) for supersonic transport airplanes is disclosed. In its stowed position, the leading edge flap forms the lower surface of the wing leading edge up to the horizontal center of the leading edge radius. For low speed operation, the vortex leading edge flap moves forward and rotates down. The upward curve of the flap leading edge triggers flow separation on the flap and rotational flow on the upper surface of the flap (vortex). The rounded shape of the upper fixed leading edge provides the conditions for a controlled reattachment of the flow on the upper wing surface and therefore a stable vortex. The vortex generates lift and a nose-up pitching moment. This improves maximum lift at low speed, reduces attitude for a given lift coefficient and improves lift to drag ratio. The mechanism (27) to move the vortex flap consists of two spanwise supports (24) with two diverging straight tracks (64 and 68) each and a screw drive mechanism (62) in the center of the flap panel (29). The flap motion is essentially normal to the airloads and therefore requires only low actuation forces.

Rudolph, Peter K. C.↗
NASA NTRS1993

Lift augmentation for highly swept wing aircraft

A pair of spaced slots, disposed on each side of an aircraft centerline and spaced well inboard of the wing leading edges, are provided in the wing upper surfaces and directed tangentially spanwise toward thin sharp leading wing edges of a highly swept, delta wing aircraft. The slots are individually connected through separate plenum chambers to separate compressed air tanks and serve, collectively, as a system for providing aircraft lift augmentation. A compressed air supply is tapped from the aircraft turbojet power plant. Suitable valves, under the control of the aircraft pilot, serve to selective provide jet blowing from the individual slots to provide spanwise sheets of jet air closely adjacent to the upper surfaces and across the aircraft wing span to thereby create artificial vortices whose suction generate additional lift on the aircraft. When desired, or found necessary, unequal or one-side wing blowing is employed to generate rolling moments for augmented lateral control. Trailing flaps are provided that may be deflected differentially, individually, or in unison, as needed for assistance in take-off or landing of the aircraft.

Rao, Dhanvada M.↗
NASA NTRS1990

Analysis and design of sidestick controller systems for general aviation aircraft

A method to design sidestick controllers for general aviation aircraft with reversible flight controls is proposed. The use of a sidestick in this type of flight vehicle generally increases the stick forces required for maneuvering; this is due to a reduction in the moment arm of application of the force. In the present study, the reduction of stick forces is achieved by incorporating geared tabs in the control-surface design. A complete analysis using the rigid-body aircraft longitudinal equations of motion and stick-force equation in coupled form is carried out. Lateral stick forces are predicted by solving the single-degree-of-freedom roll approximation and aileron stick-force equations. Data are presented for configurations with various tab areas and a wide range of gearing ratios. The results indicate that the method can be used successfully for geared-tab design and stick-force prediction. It is shown that gearing-ratio selection is critical but that tab area does not have a significant impact on the magnitude of stick forces and stick force to stick deflection gradients.

Martin, Daniel M.↗
NASA NTRSDate not supplied

Wind Tunnel Testing of AFC over a Deflected Aileron on the High-Lift Common Research Model

Active flow control (AFC) using discrete fluidic actuators distributed along the span, just upstream of the deflected aileron of the 10% scale high-lift version of the Common Research Model (CRM-HL), was evaluated during a wind tunnel test in the NASA Langley 14- by 22-Foot Subsonic Tunnel. For this set of experiments, a new outboard section was fabricated incorporating a deflectable aileron. Aileron deflection angles of 0, 7.5, 16, and 25 were investigated. This experimental investigation is in response to a recent study by Boeing potential to use AFC with a drooped aileron during takeoff to improve lift-to-drag ratio (L/D) by as much as 5%, depending on AFC mass flow rate. AFC is used at deflection angles above the nominal deflection of 7.5 to control the resulting flow separation that occurs and potentially improve L/D. Improvements in aircraft low-speed L/D can affect vehicle range and/or payload. Tuft flow visualization data, steady and unsteady surface pressure data, and force and moment data are used to compare the flowfields with and without AFC. Parameters varied include actuator momentum coefficient and aileron deflection angle. The surface pressure and tuft flow visualization results indicate that without AFC, the flow over a majority of the aileron upper surface is separated for aileron deflection angles larger than 7.5. When AFC is applied, the flow is reattached to the aileron. Force and moment results show that a local increase in lift leads to an increase in L/D of at least 3.5% using mass flow rates thought to be available from air sources onboard a commercial transport.

AFC↗
NASA NTRSDate not supplied

Wind Tunnel Testing of AFC over a Deflected Aileron on the High-Lift Common Research Model

Active flow control (AFC) using discrete fluidic actuators distributed along the span, just upstream of the deflected aileron of the 10% scale high-lift version of the Common Research Model (CRM-HL), was evaluated during a wind tunnel test in the NASA Langley 14- by 22-Foot Subsonic Tunnel. For this set of experiments, a new outboard section was fabricated incorporating a deflectable aileron. Aileron deflection angles of 0, 7.5, 16, and 25 were investigated. This experimental investigation is in response to a recent study by Boeing potential to use AFC with a drooped aileron during takeoff to improve lift-to-drag ratio (L/D) by as much as 5%, depending on AFC mass flow rate. AFC is used at deflection angles above the nominal deflection of 7.5 to control the resulting flow separation that occurs and potentially improve L/D. Improvements in aircraft low-speed L/D can affect vehicle range and/or payload. Tuft flow visualization data, steady and unsteady surface pressure data, and force and moment data are used to compare the flowfields with and without AFC. Parameters varied include actuator momentum coefficient and aileron deflection angle. The surface pressure and tuft flow visualization results indicate that without AFC, the flow over a majority of the aileron upper surface is separated for aileron deflection angles larger than 7.5. When AFC is applied, the flow is reattached to the aileron. Force and moment results show that a local increase in lift leads to an increase in L/D of at least 3.5% using mass flow rates thought to be available from air sources onboard a commercial transport.

AFC↗