Search NASA⌕ Search

SEARCH · Search NASA

Results for “CONTROL SURFACES - TRAILING EDGES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Submicrometer spectromicroscopy of UO 2 aged under high humidity conditions

We report the oxidation of uranium dioxide is a complicated process, depending on factors including humidity, temperature, and microstructure. To further determine the characteristics of this process, UO 2 particles were allowed to age and agglomerate under 98% relative humidity at room temperature for 378 days. A focused ion beam (FIB) section of this agglomeration was then measured at the O K-edge, U N 5 -edge, and C K-edge using the scanning transmission x-ray microscope (STXM) at the Advanced Light Source. O K-edge and U N 5 -edge x-ray absorption measurements allowed for the elemental and chemical species mapping of the agglomerates and indicated the formation of schoepite at the submicrometer scale in specific locations. Non-negative matrix factorization was employed to elucidate the main components at the O K-edge, which were uranyl (schoepite) formed primarily at the interface of the sample with controlled atmosphere, a UO 2 -like bulk component present in the majority of the sample, and an oxygen species present at the surface of the FIB section, which is likely adsorbed water. STXM spectromicroscopy measurements at the U N 5 -edge measurements also confirmed the location of oxidized uranium. This analysis is a valuable insight into the formation of schoepite on UO 2 and shows the sensitivity to and utility of STXM spectromicroscopy for uranium speciation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1987

Composite grid and finite-volume LU implicit scheme for turbine flow analysis

A composite grid was generated in an attempt to improve grid quality for a typical turbine blade with large camber in terms of mesh control, smoothness, and orthogonality. This composite grid consists of the C grid (or O grid) in the immediate vicinity of the blade and the H grid in the upstream region and in the middle of the blade passage between the C grids. It provides a good boundary layer resolution around the leading edge region for viscous calculation, has orthogonality at the blade surface and slope continuity at the C-H (or O-H) interface, and has flexibility in controlling the mesh distribution in the upstream region without using excessive grid points. This composite grid eliminates the undesirable qualities of a single grid when generated for a typical turbine geometry. A finite-volume lower-upper (LU) implicit scheme can be used in solving for the turbine flows on the composite grid. This grid has a special grid node that is connected to more than four neighboring nodes in two dimensions and to more than six nodes in three dimensions. But the finite-volume approach poses no problem at the special point because each interior cell has only four neighboring cells in two dimensions and only six cells in three dimensions. The finite-volume LU implicit scheme was demonstrated to be robust and efficient for both external and internal flows in a broad flow regime.

Choo, Yung K.↗
NASA NTRS1987

Composite grid and finite-volume LU implicit scheme for turbine flow analysis

A composite grid was generated in an attempt to improve grid quality for a typical turbine blade with large camber in terms of mesh control, smoothness, and orthogonality. This composite grid consists of the C grid (or O grid) in the immediate vicinity of the blade and the H grid in the upstream region and in the middle of the blade passage between the C grids. It provides a good boundary layer resolution around the leading edge region for viscous calculation, has orthogonality at the blade surface and slope continuity at the C-H (or O-H) interface, and has flexibility in controlling the mesh distribution in the upstream region without using excessive grid points. This composite grid eliminates the undesirable qualities of a single grid when generated for a typical turbine geometry. A finite-volume lower-upper (LU) implicit schemes can be used in solving for the turbine flows on the composite grid. This grid has a special grid node that is connected to more than four neighboring nodes in two dimensions and to more than six nodes in three dimensions. But the finite-volume approach poses no problem at the special point because each interior cell has only four neighboring cells in two dimensions and only six cells in three dimensions. The finite-volume LU implicit scheme was demonstrated to be robust and efficient for both external and internal flows in a broad flow regime.

Choo, Yung K.↗
DOE OSTI2021

Formation of three-dimensional bicontinuous structures via molten salt dealloying studied in real-time by in situ synchrotron X-ray nano-tomography

Abstract Three-dimensional bicontinuous porous materials formed by dealloying contribute significantly to various applications including catalysis, sensor development and energy storage. This work studies a method of molten salt dealloying via real-time in situ synchrotron three-dimensional X-ray nano-tomography. Quantification of morphological parameters determined that long-range diffusion is the rate-determining step for the dealloying process. The subsequent coarsening rate was primarily surface diffusion controlled, with Rayleigh instability leading to ligament pinch-off and creating isolated bubbles in ligaments, while bulk diffusion leads to a slight densification. Chemical environments characterized by X-ray absorption near edge structure spectroscopic imaging show that molten salt dealloying prevents surface oxidation of the metal. In this work, gaining a fundamental mechanistic understanding of the molten salt dealloying process in forming porous structures provides a nontoxic, tunable dealloying technique and has important implications for molten salt corrosion processes, which is one of the major challenges in molten salt reactors and concentrated solar power plants.

36 MATERIALS SCIENCE↗
NASA NTRS1994

Investigation of a Laminar Flow Leading Edge

The recent resurgence of interest in utilizing laminar flow on aircraft surfaces for reduction in skin friction drag has generated a considerable amount of research in natural laminar flow (NLF) and hybrid laminar flow control (HLFC) on transonic aircraft wings. This research has focused primarily on airfoil design and understanding transition behavior with little concern for the surface imperfections and manufacturing variations inherent to most production aircraft. In order for laminar flow to find wide-spread use on production aircraft, techniques for constructing the wings must be found such that the large surface imperfections present in the leading edge region of current aircraft do not occur. Toward this end, a modification to existing leading edge construction techniques was devised such that the resulting surface did not contain large gaps and steps as are common on current production aircraft of this class. A lowspeed experiment was first conducted on a simulation of the surface that would result from this construction technique. Preston tube measurements of the boundary layer downstream of the simulated joint and flow visualization using sublimation chemicals validated the literature on the effects of steps on a laminar boundary layer. These results also indicated that the construction technique was indeed compatible with laminar flow. In order to fully validate the compatibility of this construction technique with laminar flow, thus proving that it is possible to build wings that are smooth enough to be used on business jets and light transports in a manner compatible with laminar flow, a flight experiment is being conducted. In this experiment Mach number and Reynolds number will be matched in a real flight environment. The experiment is being conducted using the NASA Dryden F-104 Flight Test Fixture (FTF). The FTF is a low aspect ratio ventral fin mounted beneath an F-104G research aircraft. A new nose shape was designed and constructed for this experiment. This nose shape provides an accelerating pressure gradient in the leading edge region. By flying the aircraft at appropriate Mach numbers and altitudes, this nose shape simulates the leading edge region of a laminar flow wing for a business jet or light transport. Manufactured into the nose shape is a spanwise slot located approximately four inches downstream of the leading edge. The slot, which is an inch wide and one-eighth of an inch deep allows the simulation of surface imperfections, such as gaps and steps at skin joints, which will occur on aircraft using this new construction technique. By placing strips of aluminum of various sizes and shapes in the slot, the effect on the boundary layer of different sizes and shapes of steps and gaps will be examined. It is planned to use five different configurations, differing primarily in the size and number of gaps. Downstream of the slot, the state of the boundary layer is determined using hot film gages and Stanton gages. Agreement between these two very different techniques of measuring boundary layer properties is considered important to being able to state with confidence the effects on the boundary layer of the simulated manufacturing imperfections. To date, the aircraft has not flown. First flights of the aircraft are on schedule to begin October 4, 1993. Low-speed, preliminary experiments at matching Reynolds numbers have been completed.

Drake, Aaron↗
NASA NTRS1945

Summary of Airfoil Data

The historical development of NACA airfoils is briefly reviewed. New data are presented that permit the rapid calculation of the approximate pressure distributions for the older NACA four-digit and five-digit airfoils by the same methods used for the NACA 6-series airfoils. The general methods used to derive the basic thickness forms for NACA 6 and 7-series airfoils together with their corresponding pressure distributions are presented. Detail data necessary for the application of the airfoils to wing design are presented in supplementary figures placed at the end of the paper. The report includes an analysis of the lift, drag, pitching-moment, and critical-speed characteristics of the airfoils, together with a discussion of the effects of surface conditions. Available data on high-lift devices are presented. Problems associated with lateral-control devices, leading-edge air intakes, and interference are briefly discussed, together with aerodynamic problems of application. (author)

Abbott, Ira H↗
NASA NTRS2017

CFD Study of NACA 0018 Airfoil with Flow Control

The abilities of two different Reynolds-Averaged Navier-Stokes codes to predict the effects of an active flow control device are evaluated. The flow control device consists of a blowing slot located on the upper surface of an NACA 0018 airfoil, near the leading edge. A second blowing slot present on the airfoil near mid-chord is not evaluated here. Experimental results from a wind tunnel test show that a slot blowing with high momentum coefficient will increase the lift of the airfoil (compared to no blowing) and delay flow separation. A slot with low momentum coefficient will decrease the lift and induce separation even at low angles of attack. Two codes, CFL3D and FUN3D, are used in two-dimensional computations along with several different turbulence models. Two of these produced reasonable results for this flow, when run fully turbulent. A more advanced transition model failed to predict reasonable results, but warrants further study using different inputs. Including inviscid upper and lower tunnel walls in the simulations was found to be important in obtaining pressure distributions and lift coefficients that best matched experimental data. A limited number of three-dimensional computations were also performed.

Eggert, Christopher A.↗
DOE OSTI2020

Direct observation of anisotropic growth of water films on minerals driven by defects and surface tension

Knowledge of the occurrences of water films on minerals is critical for global biogeochemical and atmospheric processes, including element cycling and ice nucleation. The underlying mechanisms controlling water film growth are, however, misunderstood. Using infrared nanospectroscopy, amplitude-modulated atomic force microscopy, and molecular simulations, we show how water films grow from water vapor on hydrophilic mineral nanoparticles. We imaged films with up to four water layers that grow anisotropically over a single face. Growth usually begins from the near edges of a face where defects preferentially capture water vapor. Thicker films produced by condensation cooling completely engulf nanoparticles and form thicker menisci over defects. The high surface tension of water smooths film surfaces and produces films of inhomogeneous thickness. Nanoscale topography and film surface energy thereby control anisotropic distributions and thicknesses of water films on hydrophilic mineral nanoparticles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Andreev reflection of quantum Hall states through a quantum point contact

Here, we investigate the interplay between the quantum Hall (QH) effect and superconductivity in InAs surface quantum well (SQW)/NbTiN heterostructures using a quantum point contact (QPC). We use QPC to control the proximity of the edge states to the superconductor. By measuring the upstream and downstream resistances of the device, we investigate the efficiency of Andreev conversion at the InAs/NbTiN interface. Our experimental data is analyzed using the Landauer Büttiker formalism, generalized to allow for Andreev reflection processes. We show that by varying the voltage of the QPC, V QPC , the average Andreev reflection, A, at the QH-SC interface can be tuned from 50% to ~ 10%. The evolution of A with V QPC extracted from the measurements exhibits plateaus separated by regions for which A varies continuously with V QPC . The presence of plateaus suggests that for some ranges of V QPC the QPC might be pinching off almost completely from the QH-SC interface some of the edge modes. Our work shows a new experimental setup to control and advance the understanding of the complex interplay between superconductivity and QH effect in two-dimensional gas systems.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1931

Experiments with an Airfoil Model on which the Boundary Layers are Controlled Without the Use of Supplementary Equipment

This report describes test made in the Variable Density Wind Tunnel of the NACA to determine the possibility of controlling the boundary layer on the upper surface of an airfoil by use of the low pressure existing near the leading edge. The low pressure was used to induce flow through slots in the upper surface of the wing. The tests showed that the angle of attack for maximum lift was increased at the expense of a reduction in the maximum lift coefficient and an increase in the drag coefficient.

Abbott, I H↗
NASA NTRS1999

Active Control of Flow Separation Over an Airfoil

Designing an aircraft without conventional control surfaces is of interest to aerospace community. In this direction, smart actuator devices such as synthetic jets have been proposed to provide aircraft maneuverability instead of control surfaces. In this article, a numerical study is performed to investigate the effects of unsteady suction and blowing on airfoils. The unsteady suction and blowing is introduced at the leading edge of the airfoil in the form of tangential jet. Numerical solutions are obtained using Reynolds-Averaged viscous compressible Navier-Stokes equations. Unsteady suction and blowing is investigated as a means of separation control to obtain lift on airfoils. The effect of blowing coefficients on lift and drag is investigated. The numerical simulations are compared with experiments from the Tel-Aviv University (TAU). These results indicate that unsteady suction and blowing can be used as a means of separation control to generate lift on airfoils.

Ravindran, S. S.↗
NASA NTRS1978

Flight investigation of insect contamination and its alleviation

An investigation of leading edge contamination by insects was conducted with a JetStar airplane instrumented to detect transition on the outboard leading edge flap and equipped with a system to spray the leading edge in flight. The results of airline type flights with the JetStar indicated that insects can contaminate the leading edge during takeoff and climbout. The results also showed that the insects collected on the leading edges at 180 knots did not erode at cruise conditions for a laminar flow control airplane and caused premature transition of the laminar boundary layer. None of the superslick and hydrophobic surfaces tested showed any significant advantages in alleviating the insect contamination problem. While there may be other solutions to the insect contamination problem, the results of these tests with a spray system showed that a continouous water spray while encountering the insects is effective in preventing insect contamination of the leading edges.

Peterson, J. B., Jr.↗
NASA NTRS1978

Flight experience on the need and use of inflight leading edge washing for a laminar flow airfoil

An investigation of leading-edge contamination by insects was conducted at the NASA Dryden Flight Research Center with a JetStar airplane instrumented to detect transition on the outboard leading-edge flap and equipped with a system to wash the leading edge in flight. The results of airline-type flights with the JetStar indicated that insects can contaminate the leading edge during take-off and climbout at large jet airports in the United States. The results also showed that the insects collected on the leading edges at 180 knots did not erode at cruise conditions for a laminar flow control airplane and caused premature transition of the laminar boundary layer. None of the superslick and hydrophobic surfaces tested showed any significant advantages in alleviating the insect contamination problem. While there may be other solutions to the insect contamination problem, the results of these tests with a washer system showed that a continuous water spray while encountering the insects is effective in preventing insect contamination of the leading edges.

Fisher, D. F.↗
DOE OSTI2021

Self-Anchored Platinum-Decorated Antimony-Doped-Tin Oxide as a Durable Oxygen Reduction Electrocatalyst

The lifetime of commercial Proton Exchange Membrane Fuel Cells (PEMFCs) is circumscribed by the insufficient durability of commercial catalysts. The use of metal oxide supports in place of carbon significantly increases electrocatalyst durability. Herein, following density functional theory (DFT) predictions of improved Platinum (Pt) stability on antimony doped tin oxide (ATO) supports, we synthesized ATO whose morphology and crystal structure was engineered using a Pt anchoring technique. X-ray photoelectron spectroscopy (XPS) indicated that the Pt anchor sites aided in the reduction of Pt precursors to Pt on the ATO surface. X-ray absorption near-edge spectroscopy (XANES) revealed the existence of strong-metal-support interactions (SMSI) between Pt and ATO. The combination of SMSI and high control over Pt dispersion enabled the Pt/Pt-aerogel-ATO (Pt supported on aerogel ATO with Pt anchor sites) electrocatalyst to achieve 2x the area specific activity of Pt/C in ex-situ testing. In a H 2 /air PEMFC Pt/Pt-aerogel-ATO cathodes enabled 20% higher peak power density and <1/6 the loss of active surface area as compared to Pt/C. Notably, in a PEMFC under rigorous potential cycling, the Pt/Pt-aerogel-ATO retained its initial peak power density as opposed to a 58% loss for Pt/C. Further, cost models indicate that Pt/Pt-aerogel-ATO is 26% less expensive than Pt/C over its useful lifetime.

25 ENERGY STORAGE↗
NASA NTRS1987

Differential surface models for tactile perception of shape and on-line tracking of features

Tactile perception of shape involves an on-line controller and a shape perceptor. The purpose of the on-line controller is to maintain gliding or rolling contact with the surface, and collect information, or track specific features of the surface such as edges of a certain sharpness. The shape perceptor uses the information to perceive, estimate the parameters of, or recognize the shape. The differential surface model depends on the information collected and on the a priori information known about the robot and its physical parameters. These differential models are certain functionals that are projections of the dynamics of the robot onto the surface gradient or onto the tangent plane. A number of differential properties may be directly measured from present day tactile sensors. Others may have to be indirectly computed from measurements. Others may constitute design objectives for distributed tactile sensors of the future. A parameterization of the surface leads to linear and nonlinear sequential parameter estimation techniques for identification of the surface. Many interesting compromises between measurement and computation are possible.

Hemami, H.↗
NASA NTRS1987

Experimental studies on Goertler vortices

Goertler vortices arise in laminar boundary layers along concave walls due to an imbalance between pressure and centrifugal forces. In advanced laminar-flow control (LFC) supercritical airfoil designs, boundary-layer suction is primarily used to control Tollmien-Schlichting instability and cross-flow vortices in the concave region near the leading edge of the airfoil lower surface. The concave region itself is comprised of a number of linear segments positioned to limit the total growth of Goertler vortices. Such an approach is based on physical reasonings but rigorous theoretical justification or experimental evidence to support such an approach does not exist. An experimental project was initiated at NASA Langley to verify this concept. In the first phase of the project an experiment was conducted on an airfoil whose concave region has a continuous curvature distribution. Some results of this experiment were previously reported and significant features are summarized.

Mangalam, Siva M.↗
NASA NTRS1999

High Reynolds Number Hybrid Laminar Flow Control (HLFC) Flight Experiment: Suction System Design and Manufacture - Report 4

This document describes the design of the leading edge suction system for flight demonstration of hybrid laminar flow control on the Boeing 757 airplane. The exterior pressures on the wing surface and the required suction quantity and distribution were determined in previous work. A system consisting of porous skin, sub-surface spanwise passages ("flutes"), pressure regulating screens and valves, collection fittings, ducts and a turbocompressor was defined to provide the required suction flow. Provisions were also made for flexible control of suction distribution and quantity for HLFC research purposes. Analysis methods for determining pressure drops and flow for transpiration heating for thermal anti-icing are defined. The control scheme used to observe and modulate suction distribution in flight is described.

Source record↗
DOE OSTI2024

Abrasive Waterjet Machining

The abrasive waterjet machining process was introduced in the 1980s as a new cutting tool; the process has the ability to cut almost any material. Currently, the AWJ process is used in many world-class factories, producing parts for use in daily life. A description of this process and its influencing parameters are first presented in this paper, along with process models for the AWJ tool itself and also for the jet–material interaction. The AWJ material removal process occurs through the high-velocity impact of abrasive particles, whose tips micromachine the material at the microscopic scale, with no thermal or mechanical adverse effects. The macro-characteristics of the cut surface, such as its taper, trailback, and waviness, are discussed, along with methods of improving the geometrical accuracy of the cut parts using these attributes. For example, dynamic angular compensation is used to correct for the taper and undercut in shape cutting. The surface finish is controlled by the cutting speed, hydraulic, and abrasive parameters using software and process models built into the controllers of CNC machines. In addition to shape cutting, edge trimming is presented, with a focus on the carbon fiber composites used in aircraft and automotive structures, where special AWJ tools and manipulators are used. Examples of the precision cutting of microelectronic and solar cell parts are discussed to describe the special techniques that are used, such as machine vision and vacuum-assist, which have been found to be essential to the integrity and accuracy of cut parts. The use of the AWJ machining process was extended to other applications, such as drilling, boring, milling, turning, and surface modification, which are presented in this paper as actual industrial applications. To demonstrate the versatility of the AWJ machining process, the data in this paper were selected to cover a wide range of materials, such as metal, glass, composites, and ceramics, and also a wide range of thicknesses, from 1 mm to 600 mm. The trends of Industry 4.0 and 5.0, AI, and IoT are also presented.

36 MATERIALS SCIENCE↗