Search NASA⌕ Search

SEARCH · Search NASA

Results for “CRITICAL STRESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

A renormalization group model for the stick-slip behavior of faults

A fault which is treated as an array of asperities with a prescribed statistical distribution of strengths is described. For a linear array the stress is transferred to a single adjacent asperity and for a two dimensional array to three ajacent asperities. It is shown that the solutions bifurcate at a critical applied stress. At stresses less than the critical stress virtually no asperities fail on a large scale and the fault is locked. At the critical stress the solution bifurcates and asperity failure cascades away from the nucleus of failure. It is found that the stick slip behavior of most faults can be attributed to the distribution of asperities on the fault. The observation of stick slip behavior on faults rather than stable sliding, why the observed level of seismicity on a locked fault is very small, and why the stress on a fault is less than that predicted by a standard value of the coefficient of friction are outlined.

Smalley, R. F., Jr.↗
NASA NTRS1985

A renormalization group approach to the stick-slip behavior of faults

A fault which is treated as an array of asperities with a perscribed statistical distribution of strengths is described. For a linear array the stress is transferred to a single adjacent asperity and for a two dimensional array to three adjacent asperities. It is shown that the solutions bifurcate at a critical applied stress. At stresses less than the critical stress virtually no asperities fail on a large scale and the fault is locked. At the critical stress the solution bifurcates and asperity failure cascades away from the nucleus of failure. It is found that the stick slip behavior of most faults can be attributed to the distribution of asperities on the fault. The observation of stick slip behavior on faults rather than stable sliding, why the observed level of seismicity on a locked fault is very small, and why the stress on a fault is less than that predicted by a standard value of the coefficient of friction are outlined.

Smalley, R. F., Jr.↗
NASA NTRS1997

The Effects of Composition and gamma'/gamma Lattice Parameter Mismatch on the Critical Resolved Shear Stresses for Octahedral and Cube Slip in NiAlCrX Alloys

Prototypical single-crystal NiAlCrX superalloys were studied to examine the effects of the common major alloying elements, Co, Mo, Nb, Ta, Ti, and W, on yielding behavior. The alloys contained about 10 at. pct Cr, 60 vol pct of the gamma' phase, and about 3 at. pct of X in the gamma'. The critical resolved shear stresses (CRSSs) for octahedral and primary cube slip were measured at 760 C, which is about the peak strength temperature. The CRSS(sub oct) and CRSS(sub cube) are discussed in relation to those of Ni, (Al, X) gamma' alloys taken from the literature and the gamma'/gamma lattice mismatch. The CRSS(sub oct) of the gamma + gamma' alloys reflected a similar compositional dependence to that of both the CRSS(sub cube) of the gamma' phase and the gamma'/gamma lattice parameter mismatch. The CRSS(sub cube) of the gamma + gamma' alloys also reflected the compositional dependence of the gamma'/gamma mismatch, but bore no similarity to that of CRSS(sub cube) for gamma' alloys since it is controlled by the gamma matrix. The ratio of CRSS(sub cube)/CRSS(sub oct) was decreased by all alloying elements except Co, which increased the ratio. The decrease in CRSS(sub cube)/CRSS(sub oct) was related to the degree in which elements partition to the gamma' rather than the gamma phase.

Miner, R. V.↗
NASA NTRS1945

Effect of Normal Pressure on the Critical Compressive and Shear Stress of Curved Sheet

Results are presented of tests of two sets of 20 curved-sheet specimens to determine the effect of normal pressure on the critical compressive and shear stress of curved sheets. It was found that normal pressure raised the critical compressive and shear stress of curved sheets except when outward bulging occurred in compression, in which case the critical stress was lowered by normal pressure. (author)

Rafel, Norman↗
NASA NTRS1987

A loading system for creep testing under constant compressive stress

A critical analysis is made of layouts assuring constant stress under creep, pointing out the difficulties of using these layouts for compressive testing. A new mechanical system to maintain stress during creep testing is proposed. Constant stress is achieved by a definite motion of the load. The proposed system can be used in tensile or compressive testing. Practical measurements reveal that the stress constancy error is not greater than plus or minus 1.5 percent up to relative deformation of 30 percent.

Dobes, F.↗
NASA NTRS1979

A critical examination of stresses in an elastic single lap joint

The results of an approximate nonlinear finite-element analysis of a single lap joint are presented and compared with the results of a linear finite-element analysis, and the geometric nonlinear effects caused by the load-path eccentricity on the adhesive stress distributions are determined. The results from finite-element, Goland-Reissner, and photoelastic analyses show that for a single lap joint the effect of the geometric nonlinear behavior of the joint has a sizable effect on the stresses in the adhesive. The Goland-Reissner analysis is sufficiently accurate in the prediction of stresses along the midsurface of the adhesive bond to be used for qualitative evaluation of the influence of geometric or material parametric variations. Detailed stress distributions in both the adherend and adhesive obtained from the finite-element analysis are presented to provide a basis for comparison with other solution techniques.

Cooper, P. A.↗
NASA NTRS2005

Stress Analysis of B-52B and B-52H Air-Launching Systems Failure-Critical Structural Components

The operational life analysis of any airborne failure-critical structural component requires the stress-load equation, which relates the applied load to the maximum tangential tensile stress at the critical stress point. The failure-critical structural components identified are the B-52B Pegasus pylon adapter shackles, B-52B Pegasus pylon hooks, B-52H airplane pylon hooks, B-52H airplane front fittings, B-52H airplane rear pylon fitting, and the B-52H airplane pylon lower sway brace. Finite-element stress analysis was performed on the said structural components, and the critical stress point was located and the stress-load equation was established for each failure-critical structural component. The ultimate load, yield load, and proof load needed for operational life analysis were established for each failure-critical structural component.

Ko, William L.↗
NASA NTRS1973

Tensile fracture of unidirectional B-Al composite.

Fracture studies on unidirectional boron filament/aluminum matrix composite under axial tension were conducted using scanning electron microscopy, microradiography, and an acoustic emission technique. The combination of these analysis techniques has allowed the description and microstructural characterization of a new noncumulative fracture mode which involves filament break propagation. This fracture mode was found to severely limit the tensile strength of the composite, since the initiation of break propagation leads immediately to catastrophic failure at filament stress levels above a critical value. This critical filament stress was found to be 170,000 psi, and it appeared to be independent of filament diameter, number of filament layers, and the type of matrix alloy.

Steele, J. H.↗
NASA NTRS1976

A plane strain analysis of the blunted crack tip using small strain deformation plasticity theory

A deformation plasticity analysis of the tip region of a blunted crack in plane strain is presented. The power hardening material is incompressible both elastically and plastically, in order to simulate behavior of a stress freezing material above critical temperature. Stress and displacement fields surrounding the crack tip are presented. The results indicate that the maximum stress seen at the crack tip is indeed limited and is determined by the tensile properties; however, the scale over which the stresses act is dependent on the loading. Comparisons are good between the forward crack tip displacement and micro-fractographic measurments of stretch zones observed in plane strain fracture toughness tests.

Mcgowan, J. J.↗
NASA NTRS1984

Theoretical model of impact damage in structural ceramics

This paper presents a mechanistically consistent model of impact damage based on elastic failures due to tensile and shear overloading. An elastic axisymmetric finite element model is used to determine the dynamic stresses generated by a single particle impact. Local failures in a finite element are assumed to occur when the primary/secondary principal stresses or the maximum shear stress reach critical tensile or shear stresses, respectively. The succession of failed elements thus models macrocrack growth. Sliding motions of cracks, which closed during unloading, are resisted by friction and the unrecovered deformation represents the 'plastic deformation' reported in the literature. The predicted ring cracks on the contact surface, as well as the cone cracks, median cracks, radial cracks, lateral cracks, and damage-induced porous zones in the interior of hot-pressed silicon nitride plates, matched those observed experimentally. The finite element model also predicted the uplifting of the free surface surrounding the impact site.

Liaw, B. M.↗
NASA NTRS1990

Interfacial sliding near a free surface in a fibrous or layered composite during thermal cycling

This paper presents a simple shear lag model of interfacial sliding at a free surface in a layered or continuous fiber composite. The interface is characterized by a critical interfacial shear stress, tau0, which might represent the critical stress for frictional sliding at a weakly bonded interface, or the shear flow stress of a thin ductile interface layer at a well bonded interface. The history, during heating and cooling, of the relative normal displacement of the reinforcing inclusions and the matrix on a free surface cut normal to the inclusions is calculated and shown to depend on both the absolute value and the temperature dependence of tau0, as well as on the magnitudes of the bulk residual stresses. The variety of possible displacement histories suggests that they are a rich source of information about tau0 and the residual stresses.

Cox, B. N.↗
NASA NTRS1995

Real time acousto-ultrasonic NDE technique for monitoring damage in ceramic composites under dynamic loads

Research effort was directed towards developing a near real-time, acousto-ultrasonic (AU), nondestructive evaluation (NDE) tool to study the failure mechanisms of ceramic composites. Progression of damage is monitored in real-time by observing the changes in the received AU signal during the actual test. During the real-time AU test, the AU signals are generated and received by the AU transducers attached to the specimen while it is being subjected to increasing quasi-static loads or cyclic loads (10 Hz, R = 1.0). The received AU signals for 64 successive pulses were gated in the time domain (T = 40.96 micro sec) and then averaged every second over ten load cycles and stored in a computer file during fatigue tests. These averaged gated signals are representative of the damage state of the specimen at that point of its fatigue life. This is also the first major attempt in the development and application of real-time AU for continuously monitoring damage accumulation during fatigue without interrupting the test. The present work has verified the capability of the AU technique to assess the damage state in silicon carbide/calcium aluminosilicate (SiC/CAS) and silicon carbide/ magnesium aluminosilicate (SiC/MAS) ceramic composites. Continuous monitoring of damage initiation and progression under quasi-static ramp loading in tension to failure of unidirectional and cross-ply SiC/CAS and quasi-isotropic SiC/MAS ceramic composite specimens at room temperature was accomplished using near real-time AU parameters. The AU technique was shown to be able to detect the stress levels for the onset and saturation of matrix cracks, respectively. The critical cracking stress level is used as a design stress for brittle matrix composites operating at elevated temperatures. The AU technique has found that the critical cracking stress level is 10-15% below the level presently obtained for design purposes from analytical models. An acousto-ultrasonic stress-strain response (AUSSR) model for unidirectional and cross-ply ceramic composites was formulated. The AUSSR model predicts the strain response to increasing stress levels using real-time AU data and classical laminated plate theory. The Weibull parameters of the AUSSR model are used to calculate the design stress for thermo-structural applications. Real-time AU together with the AUSSR model was used to study the failure mechanisms of SiC/CAS ceramic composites under static and fatigue loading. An S-N curve was generated for a cross-ply SiC/CAS ceramic composite material. The AU results are corroborated and complemented by other NDE techniques, namely, in-situ optical microscope video recordings and edge replication.

Tiwari, Anil↗
NASA NTRS1949

Critical combinations of shear and direct axial stress for curved rectangular panels

A solution is presented for the problem of the buckling of curved rectangular panels subjected to combined shear and direct axial stress. Charts giving theoretical critical combinations of shear and direct axial stress are presented for panels having five different length-width ratios. Because the actual critical compressive stress of rectangular panels having substantial curvature is known to be much lower than the theoretical value, a semiempirical method of analysis of curved panels subjected to combined shear and direct axial stress is presented for use in design. (author

PLATES - STRESSES, SHEARING CURVED↗
NASA NTRS2012

Thermostructural Evaluation of Joggle Region on the Shuttle Orbiter's Wing Leading Edge

An investigation was initiated to determine the cause of coating spallation occurring on the Shuttle Orbiter's wing leading edge panels in the slip-side joggle region. The coating spallation events were observed, post flight, on differing panels on different missions. As part of the investigation, the high re-entry heating occurring on the joggles was considered here as a possible cause. Thus, a thermostructural evaluation was conducted to determine the detailed state-of-stress in the joggle region during re-entry and the feasibility of a laboratory test on a local joggle specimen to replicate this state-of-stress. A detailed three-dimensional finite element model of a panel slip-side joggle region was developed. Parametric and sensitivity studies revealed significant stresses occur in the joggle during peak heating. A critical interlaminar normal stress concentration was predicted in the substrate at the coating interface and was confined to the curved joggle region. Specifically, the high interlaminar normal stress is identified to be the cause for the occurrence of failure in the form of local subsurface material separation occurring in the slip-side joggle. The predicted critical stresses are coincident with material separations that had been observed with microscopy in joggle specimens obtained from flight panels.

Walker, Sandra P.↗
NASA NTRS1972

Required critical aspect ratio of fibers intended for stress rupture applications.

The observed critical aspect ratio for pullout specimens of tungsten wire in a copper matrix tested in stress rupture at 649 and 816 C was slightly greater than for tension tests at the same temperature. Time for failure of the stress rupture specimens was controlled by the properties of the fiber (tungsten) at aspect ratios greater than the critical aspect ratio and by the properties of the matrix (copper) at aspect ratios less than the critical ratio.

Jech, R. W.↗