Search NASA⌕ Search

SEARCH · Search NASA

Results for “Coating cracking”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

Crack detection using pulsed eddy current stimulated thermography

This contribution presents results from studies investigating factors that influence the detection of surface breaking cracks using pulsed eddy current thermography. The influences of the current strength and crack orientation in both ferromagnetic and non-ferromagnetic metals have been investigated. It has been found that crack detection is far more sensitive to crack orientation in non-ferromagnetic metals than in ferromagnetic metals. The effects of crack size on detectability are presented for a large number of steel, nickel alloy and titanium samples. Results of studies comparing crack images obtained prior and after coating a nickel alloy sample with a thermal barrier coating are presented.

36 MATERIALS SCIENCE↗

Microstructural Evolution of 7 wt.% Y2O3 ZrO2 Thermal Barrier Coatings due to Stress Relaxation at Elevated Temperatures and the Concomitant changes in Thermal Conductivity

The purpose of this study was to evaluate the combined effect of stress and temperature on the microstructure of air plasma-sprayed 7 wt.% Y{sub 2}O{sub 3}-ZrO{sub 2} thermal barrier coatings, and relate microstructural changes to the thermal conductivity, k{sub th}. To simulate TBC service conditions, stand-alone tubes of YSZ were stress relaxed, starting from a compressive stress of 60 MPa, at temperatures of 1000 C or 1200 C. The duration of the stress relaxation test was either 5 min or 3 h. Detailed scanning electron microscopy (SEM) and Porod's specific surface area (SSA) analysis of small angle neutron scattering (SANS) results were used to determine which void systems, either interlamellar pores or intralamellar cracks, contributed to the observed relaxation of stress in the coatings. SEM investigations revealed closure of intralamellar cracks located perpendicular to the stress direction. For thinner YSZ coatings, SANS measurements indicated a statistically significant reduction in the total SSA and SSA associated with intralamellar cracks after stress relaxation at the times, temperatures, and stress investigated compared to those samples that were exposed to identical times and temperatures, but no stress. The SSA associated with the interlamellar pores was not significantly smaller in YSZ coatings stress relaxed from 60 MPa at 1200 C for 3 h compared to as-sprayed coatings. The thermal conductivity of the coatings was strongly influenced by stress, with increases in kth observed after only 5 min at 60 MPa and 1200 C. Reductions in the total SSA were directly linked to increases in k{sub th}.

36 MATERIALS SCIENCE↗

Effect of APS flash bond coatings on furnace cycle lifetime of disks and rods

Air plasma sprayed (APS) flash coatings on high velocity oxygen fuel (HVOF) bond coatings are well known to extend the lifetime of thermal barrier coatings. Recent work compared flash coatings of NiCoCrAlY and NiCoCrAlYHfSi applied to both rods and disk substrates of alloy 247. For rod specimens, 100-h cycles were used at 1100°C in wet air. Both flash coatings significantly improved the lifetime compared to HVOF-only and VPS-only MCrAlY bond coatings with no statistical difference between the two flash coatings. For disk specimens tested in 1-h cycles at 1100°C in wet air, the NiCoCrAlY flash coating significantly outperformed an HVOFonly NiCoCrAlYHfSi bond coating and a NiCoCrAlYHfSi flash coating. The flash coatings formed a mixed oxide-metal zone that appeared to inhibit crack formation and extend lifetime. In addition to the flash coating increasing the bond coating roughness, the underlying HVOF layer acted as a source of Al for this intermixed zone and prevented the oxide from penetrating deeper into the bond coating. The lower Y+Hf level in the Y-only flash coating appeared to minimize oxidation in the flash layer, thereby increasing the benefit compared to a NiCoCrAlYHfSi flash coating.

Pint, Bruce↗

Residual stresses in functionally graded thermal barrier coatings

Functionally graded materials offer potential as a solution to the premature failure of thermal barrier coatings due to thermal residual stresses, however this solution has not been fully evaluated to date. An analytical methodology based on the bending of plates has been used to model the residual stress distribution through the layers of a functionally graded (FG) cermet top coat-bond layer-substrate system after cooling from a high deposition temperature. The model is then applied to two material systems with different trends in variation in the coefficient of thermal expansion from the substrate to the top coat layer. Increasing the number of layers reduces the discrete stress variations across the interfaces through the FG layers and reduces the propensity of interfacial cracking. While the stress in the top coat is always compressive for the Inconel substrate, the stress in the top coat is tensile in nature for the steel substrate when the ceramic volume fraction in the functionally graded layers is low. The stress in the top coat gradually becomes compressive with an increasing volume fraction of ceramic in the functionally graded top coat. The curvature of the TBC system follows a similar trend and changes its sign with increasing ceramic content for the steel substrate. In conclusion, the effect of the number of layers on the curvature gradually diminishes and the curvature becomes constant beyond only a few layers.

36 MATERIALS SCIENCE↗

Effect of Tungsten Inert Gas Arc Remelting on Microstructure and Wear Properties of Plasma-Sprayed NiCr-Cr{sub 3}C{sub 2} Coating

In this work, a NiCr-Cr{sub 3}C{sub 2} coating was prepared on an AISI 1045 steel substrate by plasma spraying and then remelted with the tungsten inert gas (TIG) arc method. The purpose was to study the effects of TIG remelting treatment on the microstructure, mechanical properties and wear properties of a plasma-sprayed NiCr-Cr{sub 3}C{sub 2} coating. The results show that after TIG remelting, the density of the coating increased, the internal porosity decreased from 8.1 to 0.2%, and the number of cracks and inclusions greatly reduced. The hardness of the coating also became uniform and increased from 1007 to 1141 HV{sub 0.1}, with an obvious increase of 13.3%, and the fracture toughness increased by 321.3%. The wear volume after TIG remelting at room temperature was reduced by 59.5%, and the wear pattern changed from brittle fracture and abrasive wear to abrasive wear and adhesive wear. The wear loss at 700 °C was also reduced by 43.6%, and the wear pattern was transformed from brittle fracture and fatigue wear caused by oxidation to oxidative wear and adhesive wear. Therefore, TIG remelting treatment can effectively improve the microstructure, mechanical properties and wear resistance of a plasma-sprayed NiCr-Cr{sub 3}C{sub 2} coating.

36 MATERIALS SCIENCE↗

Correlation between structural and mechanical properties of RF magnetron sputter deposited hydroxyapatite coating

Highlights: • Microstructure and mechanical properties of textured hydroxyapatite (HA) coatings were evaluated. • TEM results revealed two types of coating microstructure corresponding to the film texture. • Elastic performance of the coating was determined by the texture of the HA coating. • HA coating with (300) texture showed larger elastic recovery. - Abstract: In the present study hydroxyapatite (HA) thin films with a,b-plain and c-plain preferential orientation were prepared by means of RF-magnetron sputtering with water vapor addition into a working gas atmosphere to investigate the influence of microstructural features on mechanical performance of the coating at nanoscale. The mechanical properties of the HA coatings textured along a,b- and c-axes by nanoindentation conclusively highlight that elastic modulus, H/E ratio, H{sup 3}/E{sup 2} parameter and percent of elastic recovery are determined by preferential orientation of the film. Nanoindentation reveals that the HA films exhibiting (300) texture possess commensurate nanohardness and lower elastic modulus compared to (002) oriented films, indicating that the former films possess higher resistance to cracking. The (002) and (300) textured coatings exhibited a nanohardness of 4.7 ± 2.0 GPa and 4.4 ± 2.2 GPa, respectively. The elastic modulus of the HA film with (300) and (002) preferential orientation was 75 ± 40 GPa and 103 ± 40 GPa, respectively. The HA coating with (300) texture showed a higher percentage of elastic recovery of 92% within unloading than that of the (002) textured film (69%).

36 MATERIALS SCIENCE↗

Distinct Mechanism of Anti-Corrosion and Swelling-Adhesion Modeling of Low-Dimensional Nylon-Fluoropolymer Composite Coatings

Compared to other polymers, composite coatings with fluoropolymers as the matrix have attracted considerable interest due to their mechanical performance, chemical stability, and low surface energy. Herein, we present an anticorrosion mechanism of fluoropolymer composite coatings achieved by dispersing varying amounts of polyamide 12 (PA-12) particles over a poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) matrix. The choice of PVDF-HFP as a coating matrix was driven by its superior processability and mechanical properties over Teflon, while PA-12 afforded swelling capacity, preventing electrolyte permeation, and inhibiting matrix stress crack propagation. The corrosion resistance of the coatings was assessed mainly by potentiodynamic polarization and impedance measurements while being immersed in a NaCl solution. Our electrochemical measurement findings showed that 0.75% w/w PA-12 in the PVDF-HFP matrix significantly enhanced corrosion protection even after 21 days of immersion. Microscopy, dielectric spectroscopy, surface analysis, and mechanical testing (American Society for Testing and Materials standards) corroborated the results. PVDF-HFP coatings containing a minimum percolation threshold of 0.75 wt % PA-12 with 1 mil thickness on mild steel exhibited a remarkable increase in resistance and film adhesion, and a notable corrosion rate decrease. Finite element analysis simulation with a bilinear traction-separation law confirmed the swelling mechanism and adhesion behavior. Finally, this study highlights the potential of nylon particle dispersion in PVDF-HFP matrices as a practical approach to developing advanced anticorrosion coatings with promising practical applications in various industries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NONDESTRUCTIVE DETECTION OF DELAMINATION IN THERMAL BARRIER COATINGS USING ULTRASONIC TECHNIQUE

Nondestructive testing using an acousto-ultrasonic technique has been utilized to detect the change of material properties and provide early warning of failure of thermal barrier coating (TBC) systems. Testing was performed on René N5 and Haynes 230 coupons with an applied NETL-bond coat, as well as on coupons containing both an applied MCrAlY bond coat and 7-YSZ top coat. The coupons were subjected to either cyclic or isothermal testing at 1100ºC. Ultrasonic testing was performed before and after thermal testing using piezoelectric sensors with dry contact on the surface of the coatings. Proof-of-concept test results indicated that changes in the properties of the 40m bond coat can be detected using the proposed technique. Waveforms generated via Pitch/Catch indicated minor changes within the bond coat applied to René N5 substrate after 400500 hours of cyclic oxidation at 1100°C. In contrast, marked differences in waveforms and travel time reflected significant crack formation and spallation of the bond coat from the Haynes 230 substrate. Finite element analysis (FEA) simulation of the wave propagation on a simplified TBC system with nonlinear effects was conducted. FEA results clearly show detection of a small embedded void incorporated to simulate delamination. Comparisons between experimental measurements and finite element simulations were used to estimate the material properties of the coatings and the substrate.

36 MATERIALS SCIENCE↗

Preparation and Characterization of Sol–Gel Dip Coated Al: ZnO (AZO) Thin Film for Opto-Electronic Application

Aluminum doped zinc oxide (AZO) thin film was prepared by sol–gel dip coating method from methanol and monoethanolamine respectively, used as solvent and stabilizer agent. From the XRD study, it was confirmed that the aluminum was incorporated into the ZnO lattice. The prepared film have polycrystalline in nature and the film exhibit hexagonal wurtzite structure with (002) direction. SEM and AFM studies showed well defined smooth and uniformed wrinkle shaped grains distributed regularly on to the entire glass substrate without any pinholes and cracks. From the optical study, the observed highest transmittance was about 82% in the visible range and the band gap is 3.15 eV. Room temperature PL spectra exhibited a strong UV emission peak located at 390 nm for the deposited film. The electrical properties of the AZO thin film was studied by Hall-Effect measurement and found that it has n-type conductivity with low resistivity (ρ) of about 9.06 × 10{sup –3} Ω cm.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

PIE-Enabled Study of Aqueous Corrosion & Zr Hydriding in Cr-Coated Cladding: M3GV-23PN0101132

Chromium-coated zirconium alloy cladding is under investigation as an accident-tolerant fuel (ATF) concept to extend performance to higher burnups via improved oxidation resistance and reduced hydrogen pickup. However, hydrothermal corrosion behavior and hydrogen transport mechanisms governing in-service hydriding of these coatings remain poorly understood. In a collaborative study between Pacific Northwest National Laboratory (PNNL), Idaho National Laboratory (INL), and the University of Huddersfield, cold spray (CS) and physical vapor deposition (PVD) Cr-coated Optimized ZIRLO™ cladding samples were characterized after exposure to PWR-simulated water chemistry under both in-core (neutron irradiation) and out-of-core (aqueous-only) conditions at the MIT Research Reactor. Multi-scale characterization was performed independently at PNNL and INL to evaluate coating integrity, microstructural evolution, Cr/Zr interface chemistry, and hydride formation. Both laboratories observed a consistent divergence in hydriding behavior: out-of-core CS Cr-coated cladding exhibited elevated hydride concentrations exceeding those of uncoated cladding, whereas in-core CS samples showed substantially suppressed hydriding. In-core specimens also displayed irradiation-specific features, including nanoscale voids within the Cr coating and radiation-induced segregation clusters in the Zr substrate. CS coatings retained an interdiffusion-free Cr/Zr bond with no intermetallic layer, whereas PVD coatings exhibited inferior quality with visible cracks and pores. An automated image-based hydride quantification method systematically overestimated bulk hydrogen content relative to inert gas fusion measurements, underscoring the need for standardized sample preparation and reference standards. Interpretation of hydride nucleation and growth is complicated by the open inner-diameter of the specimens, which provides additional hydrogen pathways. The results motivate further foundational studies to support predictive models of hydrothermal corrosion and hydrogen transport in unirradiated and irradiated Cr-coated cladding.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Ceramic plasma-sprayed coating of melting crucibles for casting metal fuel slugs

Thermal cycling and melt reaction studies of ceramic coatings plasma-sprayed on Nb substrates were carried out to evaluate the performance of barrier coatings for metallic fuel casting applications. Thermal cycling tests of the ceramic plasma-sprayed coatings to 1450 degrees C showed that HfN, TiC, ZrC, and Y2O3 coating had good cycling characteristics with few interconnected cracks even after 20 cycles. Interaction studies by 1550 degrees C melt dipping tests of the plasma-sprayed coatings also indicated that HfN and Y2O3 do not form significant reaction layer between U–20 wt.% Zr melt and the coating layer. Plasma-sprayed Y2O3 coating exhibited the most promising characteristics among HfN, TiC, ZrC, and Y2O3 coating.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Effect of APS flash bond coatings and curvature on TBC performance on rod specimens

The addition of an air plasma sprayed (APS) “flash” bond coating layer on top of a high velocity oxy-fuel (HVOF) bond coating greatly extended the lifetime of APS yttria stabilized zirconia (YSZ) thermal barrier coatings (TBC) on rod specimens of superalloy 247 tested using 100-h cycles in air+10%H 2 O at 1100 °C. The flash bond coatings of both NiCoCrAlY and NiCoCrAlYHfSi powder were compared to an HVOF-only and a vacuum plasma sprayed (VPS) NiCoCrAlYHfSi bond coating. Here, the flash coatings appear to form a mixed oxide-metal zone, which likely inhibits crack formation and therefore extends lifetime compared to conventional bond coatings. The underlying dense HVOF layer appeared to act as a source of Al for this intermixed zone and prevented the oxide from penetrating deeper into the bond coating. Residual stress in the thermally-grown Al 2 O 3 scale was measured using photo-luminescence piezospectroscopy (PLPS) as a function of time for each coating variation, including a comparison of concave and convex surfaces on a specially designed rod.

36 MATERIALS SCIENCE↗

Fatigue properties of atomic-layer-deposited alumina ultra-barriers and their implications for the reliability of flexible organic electronics

The fatigue degradation properties of atomic-layer-deposited alumina, with thickness ranging from 4.2 to 50 nm, were investigated using a silicon micro-resonator on which the coatings were deposited and strained in a static or cyclic manner, with strain amplitudes up to 2.2%, in controlled environments. Based on the measured resonant frequency evolution, post-test scanning electron microscopy observations, and finite element models, it is shown that cracks in the alumina nucleate and propagate under cyclic loading, and that the crack growth rates scale with the strain energy release rates for crack channeling. The implications for the reliability of flexible electronics are discussed.

36 MATERIALS SCIENCE↗

Effect of Air Plasma Sprayed Flash Bond Coatings on Furnace Cycle Lifetime of Disks and Rods

Air plasma sprayed (APS) flash coatings on high velocity oxygen fuel (HVOF) bond coatings are well known to extend the lifetime of thermal barrier coatings (TBCs). Recent work compared flash coatings of NiCoCrAlY and NiCoCrAlYHfSi applied to both rods and disk substrates of alloy 247. For rod specimens, 100 h cycles were used at 1100 °C in wet air. Both flash coatings significantly improved the lifetime compared to HVOF-only and vacuum plasma spray (VPS)-only MCrAlY bond coatings with no statistical difference between the two flash coatings. For disk specimens tested in 1 h cycles at 1100 °C in wet air, the NiCoCrAlY flash coating significantly outperformed an HVOF-only NiCoCrAlYHfSi bond coating and a NiCoCrAlYHfSi flash coating. The flash coatings formed a mixed oxide-metal zone that appeared to inhibit crack formation and therefore extend lifetime. In addition to the flash coating increasing the bond coating roughness, the underlying HVOF layer acted as a source of Al for this intermixed zone and prevented the oxide from penetrating deeper into the bond coating. Here, the lower Y+Hf content in the Y-only flash coating appeared to minimize oxidation in the flash layer, thereby increasing the benefit compared to a NiCoCrAlYHfSi flash coating.

42 ENGINEERING↗

Designing interlayers to improve the mechanical reliability of transparent conductive oxide coatings on flexible substrates

In this study, we investigate the effect of interlayers on the mechanical properties of transparent conductive oxide (TCO) on flexible polymer substrates. Indium tin oxide (ITO), which is the most widely used TCO film, and Ti, which is the most widely used adhesive interlayer, are selected as the coating and the interlayer, respectively. These films are deposited on the polymer substrates using dc-magnetron sputtering to achieve varying thicknesses. The changes in the following critical factors for film cracking and delamination are analyzed: the internal stress ({sigma}{sup i}) induced in the coatings during deposition using a white light interferometer, the crystallinity using a transmission electron microscope, and the surface roughness of ITO caused by the interlayer using an atomic force microscope. The resistances to the cracking and delamination of ITO are evaluated using a fragmentation test. Our tests and analyses reveal the important role of the interlayers, which significantly reduce the compressive {sigma}{sup i} that is induced in the ITO and increase the resistance to the buckling delamination of the ITO. However, the relaxation of {sigma}{sup i} is not beneficial to cracking because there is less compensation for the external tension as {sigma}{sup i} further decreases. Based on these results, the microstructural control is revealed as a more influential factor than {sigma}{sup i} for improving crack resistance.

36 MATERIALS SCIENCE↗

Dry Sliding Wear Behavior and Mechanism of a Hot-Dip Aluminized Steel as a Function of Sliding Velocity

Fe-Al intermetallic coatings were prepared on AISI 1045 steel by hot-dip aluminizing and subsequent high-temperature diffusion. The dry sliding wear tests were performed for the aluminized steel with various substrate hardnesses in the velocity range of 0.75-4 m/s on a pin-on-disk configuration. The dry sliding wear behavior and mechanisms of the aluminized steel under various velocities were explored. It was found that the wear rate decreased substantially with an increase in sliding velocity from 0.75 to 1.5 and then slightly varied in the velocity range of 1.5-4 m/s. The wear behavior and mechanisms of the aluminized steel were noticed to be closely related with tribo-layers. As tribo-layers contained more oxides with Fe{sub 2}O{sub 3}, the wear resistance of the aluminized steel was markedly improved because of their protective function. The substrate hardness also changed the wear behavior of the aluminized steel by affecting the stability of tribo-layers because the substrate hardness was inversely proportional to the thermal stability of the substrate structure. Under a low velocity of 0.75 m/s, adhesive wear and abrasive wear prevailed owing to the metal-on-metal contact, resulting in a higher wear rate. At 1.5-4 m/s, mild oxidative wear prevailed due to the stable existence of tribo-oxides layers. However, at 1.5 and 4 m/s for the substrate hardness of 45 HRC, the wear rate was slightly increased because the protection of tribo-layers was weakened by a double-layered structure or more cracks in tribo-layers and coatings.

36 MATERIALS SCIENCE↗

Elevated Temperature Solid Particle Erosion Performance of Plasma-Sprayed Co-based Composite Coatings with Additions of Al{sub 2}O{sub 3} and CeO{sub 2}

In this paper, investigation into solid particle erosion behavior of atmospheric plasma-sprayed composite coating of CoCrAlY reinforced with Al{sub 2}O{sub 3} and CeO{sub 2} oxides on Superni 76 at elevated temperature of 600 °C is presented. Alumina particles are used as erodent at two impact angles of 30° and 90°. The microstructure, porosity, hardness, toughness and adhesion properties of the as-sprayed coatings are studied. The effects of temperature and phase transformation in the coatings during erosion process are analyzed using XRD and EDS techniques. Optical profilometer is used for accurate elucidation of erosion volume loss. CoCrAlY/CeO{sub 2} coating showed better erosion resistance with a volume loss of about 50% of what was observed in case of CoCrAlY/Al{sub 2}O{sub 3}/YSZ coating. Lower erosion loss is observed at 90° as compared to 30° impact angle. The erosion mechanism evaluated using SEM micrograph revealed that the coatings experienced ductile fracture exhibiting severe deformation with unusual oxide cracks. Reinforced metal oxides provide shielding effect for erodent impact, enabling better erosion resistance. The oxidation of the coating due to high-temperature exposure reforms erosion process into oxidation-modified erosion process.

36 MATERIALS SCIENCE↗

3D TRISO particle-explicit compact meshing

The TRI-structural ISOtropic (TRISO) layered fuel particle is a robust nuclear fuel form offering enhanced safety and performance for advanced reactor concepts, including high-temperature gas-cooled reactors and other Generation IV designs. These poppy-seed-sized particles are embedded in a graphite matrix to form fuel elements that must withstand elevated temperatures and high burn-up levels. The heterogeneous nature of these fuel elements — comprising thousands of randomly distributed TRISO particles — produces complex stress fields and thermal gradients that one- and two-dimensional models cannot accurately capture. While three-dimensional modeling has improved predictions of dimensional changes, internal pressure buildup, and fission product transport under irradiation, current approaches rely on homogenized material properties that are known to have considerable divergence from experimental observations. This work presents a methodology for optimized random packing of TRISO fuel compacts and full three-dimensional mesh generation within the BISON fuel performance code, with each particle coating layer individually discretized. The resulting mesh was demonstrated through heat conduction simulations under representative in-reactor operating conditions, showing strong agreement with expected behavior. This capability enables detailed analysis of particle-to-particle interactions, matrix cracking mechanisms, and the statistical distribution of coating layer failures — all of which directly govern fuel performance and safety margins.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗