Search NASA⌕ Search

SEARCH · Search NASA

Results for “Coin Cell”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Li + (ionophore) nanoclusters engineered aqueous/non-aqueous biphasic electrolyte solutions for high-potential lithium-based batteries

The use of aqueous/non-aqueous biphasic electrolyte solutions in Li-based battery systems circumvents the limitations of poor reductive stability of aqueous electrolyte solutions, broadening their electrochemical stability window. However, aqueous/non-aqueous electrolytes suffer from biphasic mixing and high impedance when Li ions cross the biphasic interface. Here we propose the use of 12-crown-4 (12C4) and tetraglyme (G4) as lithium ionophores to form Li + (ionophore) nanoclusters in both non-aqueous and aqueous phases to overcome the interface challenges in biphasic electrolytes. The Li + (ionophore) nanoclusters have the H 2 O-excluding inner Li + solvation structure in non-polar 1,1,2,2-tetrafluoroethyl 2,2,3,3-tetrafluoropropyl ether (TTE), allowing fast charge transport across the biphasic interface without solvent mixing or water shuttling. Further, a tailored electrolyte formulation comprising the lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) salt, 12C4, TTE and H 2 O solvents (labelled LiTFSI-12C4@TTE/H 2 O) demonstrates low impedance (2.7 Ω cm -2 ) at the TTE/H 2 O interface and enabling 2,000 cycles of prelithiated graphite||LiFePO 4 coin cells at 850 mA g -1 with an average Coulombic efficiency of 99.8%. Single-layer 22.5 mAh Li||LiMn 2 O 4 pouch cells using LiTFSI-12C4@TTE/H 2 O electrolyte with G4 delivered a stable discharge capacity of about 1.3 mAh cm -2 for 80 cycles at 0.5 mA cm -2 .

25 ENERGY STORAGE↗
DOE OSTI2023

Electrolyte design for Li-ion batteries under extreme operating conditions

The ideal electrolyte for the widely used LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811)||graphite lithium-ion batteries is expected to have the capability of supporting higher voltages (≥4.5 volts), fast charging (≤15 minutes), charging/discharging over a wide temperature range (±60 degrees Celsius) without lithium plating, and non-flammability. No existing electrolyte simultaneously meets all these requirements and electrolyte design is hindered by the absence of an effective guiding principle that addresses the relationships between battery performance, solvation structure and solid-electrolyte-interphase chemistry. Here we report and validate an electrolyte design strategy based on a group of soft solvents that strikes a balance between weak Li+-solvent interactions, sufficient salt dissociation and desired electrochemistry to fulfil all the aforementioned requirements. Remarkably, the 4.5-volt NMC811||graphite coin cells with areal capacities of more than 2.5 milliampere hours per square centimetre retain 75 per cent (54 per cent) of their room-temperature capacity when these cells are charged and discharged at -50 degrees Celsius (-60 degrees Celsius) at a C rate of 0.1C, and the NMC811||graphite pouch cells with lean electrolyte (2.5 grams per ampere hour) achieve stable cycling with an average Coulombic efficiency of more than 99.9 per cent at -30 degrees Celsius. The comprehensive analysis further reveals an impedance matching between the NMC811 cathode and the graphite anode owing to the formation of similar lithium-fluoride-rich interphases, thus effectively avoiding lithium plating at low temperatures. Additionally, this electrolyte design principle can be extended to other alkali-metal-ion batteries operating under extreme conditions.

25 ENERGY STORAGE↗
DOE OSTI2019

Closed Loop Recycling of Electric Vehicle Batteries to Enable Ultra-high Quality Cathode Powder

The lithium-ion battery (LIB) recycling market is becoming increasingly important because of the widespread use of LIBs in every aspect of our lives. Mobile devices and electric cars represent the largest application areas for LIBs. Vigorous innovation in these sectors is spurring continuous deployment of LIB powered devices, and consequently more and more LIBs will become waste as they approach end of life. Considering the significant economic and environmental impacts, recycling is not only necessary, but also urgent. The WPI group has successfully developed a closed-loop recycling process, and has previously demonstrated it on a relatively small scale 1 kg spent batteries per experiment. Here, we show that the closed-loop recycling process can be successfully scaled up to 30 kg of spent LIBs from electric vehicle recycling streams, and the recovered cathode powder shows similar (or better) performance to equivalent commercial powder when evaluated in both coin cells and single layer pouch cells. All of these results demonstrate the closed-loop recycling process has great adaptability and can be further developed into industrial scale.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Hybrid polymer network cathode-enabled soluble-polysulfide-free lithium–sulfur batteries

Among the emerging 'beyond lithium-ion' technologies for maximized sustainability, lithium-sulfur (Li-S) is a favoured chemistry because of its exceptional energy density from the conversion of sulfur, an element in abundant supply. However, the dissolution of several intermediate polysulfides formed during conversion leads to rapid performance degradation over cycling. Here, in this study, we address this issue by sulfurizing a hybrid polymer network with polyphosphazene and carbon as a cathode for Li-S batteries. With rich sites to re-bond and adsorb dissociative sulfur species, this hybrid polymer network circumvents the formation of soluble polysulfides and enables a unique, reversible inserting conversion reaction. Thus, our cathode delivers both high capacity (~900 mAh g -1 cathode ) and excellent cycling stability in Li-S coin cells, with a pouch cell demonstration of projected energy density of ~300 Wh kg -1 and 84.9% capacity retention after 150 cycles. The strategy can be extended to other cost-effective, recyclable polymers, advancing sulfur-based batteries towards practical energy storage application.

25 ENERGY STORAGE↗
DOE OSTI2025

Non-fluorinated electrolyte for high-voltage anode-free sodium metal battery

Abundant sodium (Na) batteries are a sustainable alternative to resource-constrained lithium-ion batteries, offering huge cost advantages. However, developing high-voltage anode-free sodium metal batteries (SMBs) to narrow the energy density gap with lithium-ion batteries is hindered by a critical challenge: existing electrolytes cannot simultaneously achieve ultra-high Na coulombic efficiency and anodic stability. Here, in this study, we present a rationally designed non-fluorinated electrolyte (1.0 M NaPF 6 in 1,2-diethoxyethane/1,2-di-tert-butoxyethane) to address this key limitation, achieving Na coulombic efficiency of >99.95% and anodic stability of >4.8 V. For coin cells (2.0 mAh cm −2 , N/P = 1.7), our electrolyte design enables 4.0 V Na | |Na 3 V 2 (PO 4 ) 3 (NVP) at 5 C and 4.3 V Na | |NaNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622) at 0.3 C for 5,000 and 500 cycles with a capacity retention >80%. Remarkably, the 50 mAh anode-free pouch cells 4.0 V Al | |NVP and 4.3 V Al | |NMC622 also achieve 500 and 300 cycles (retention >75%) with a specific energy of >360 Wh kg (electrode) −1 . This work focuses on electrolyte optimization and conceptual advances, whereas critical aspects such as safety, large-scale manufacturability and practical feasibility of SMBs require further investigation. The electrolyte design using non-fluorinated solvents enhances the anodic stability without sacrificing Na efficiency, laying groundwork for advancing low-cost, high-energy SMBs and supporting the transition to sustainable battery technologies.

25 ENERGY STORAGE↗
DOE OSTI2017

Lithium metal protected by atomic layer deposition metal oxide for high performance anodes

We present that lithium metal is a highly desirable anode material for lithium batteries due to its extremely high theoretical capacity (3860 mA h g -1 ), low potential (-3.04 V versus standard hydrogen electrode), and low density (0.534 g cm -3 ). However, dendrite growth during cycling and low coulombic efficiency, resulting in safety hazards and fast battery fading, are huge barriers to commercialization. Herein, we used atomic layer deposition (ALD) to prepare conformal, ultrathin aluminum oxide coatings on lithium. We investigated the growth mechanism during Al 2 O 3 ALD on lithium by in situ quartz crystal microbalance and found larger growth than expected during the initial cycles. We also discovered that the ALD Al 2 O 3 enhances the wettability of the Li surface towards both carbonate and ether electrolytes, leading to uniform and dense SEI formation and reduced electrolyte consumption during battery operation. Scanning electron microscopy verified that the bare Li surfaces become rough and dendritic after electrochemical cycling, whereas the ALD Al 2 O 3 coated Li surfaces remain smooth and uniform. Analysis of the Li surfaces after cycling using X-ray photoelectron spectroscopy and in situ transmission electron microscopy revealed that the ALD Al 2 O 3 coating remains intact during electrochemical cycling, and that Li ions diffuse through the coating and deposit on the underlying Li. Coin cell testing demonstrated more than two times longer cycling life for the ALD Al 2 O 3 protected Li, and a coulombic efficiency as high as ~98% at a practical current rate of 1 mA cm -2 . More significantly, when the electrolyte volume was reduced from 20 to 5 μL, the stabilizing effect of the ALD coating became even more pronounced and the cycling life was around four times longer. Finally, these results indicate that ALD Al 2 O 3 coatings are a promising strategy to stabilize Li anodes for high performance energy storage devices such as Li–S batteries.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Ionic Peltier effect in Li-ion electrolytes

The coupled transport of charge and heat provide fundamental insights into the microscopic thermodynamics and kinetics of materials. We describe a sensitive ac differential resistance bridge that enables measurements of the temperature difference on two sides of a coin cell with a resolution of better than 10 μK. We use this temperature difference metrology to determine the ionic Peltier coefficients of symmetric Li-ion electrochemical cells as a function of Li salt concentration, solvent composition, electrode material, and temperature. The Peltier coefficients Π are negative, i.e., heat flows in the direction opposite to the drift of Li ions in the applied electric field, large, –Π > 30 kJ mol –1 , and increase with increasing temperature at T > 300 K. The Peltier coefficient is approximately constant on time scales that span the characteristic time for mass diffusion across the thickness of the electrolyte, suggesting that heat of transport plays a minor role in comparison to the changes in partial molar entropy of Li at the interface between the electrode and electrolyte. Here, our work demonstrates a new platform for studying the non-equilibrium thermodynamics of electrochemical cells and provides a window into the transport properties of electrochemical materials through measurements of temperature differences and heat currents that complement traditional measurements of voltages and charge currents.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Mitigating X-ray-induced damage for accurate analysis of battery cathodes using transmission X-ray microscopy

Here, we investigate the impact of X-ray-induced damage on the evolution of battery cathodes using synchrotron transmission X-ray microscopy. In an operando coin cell, exposure to the X-ray beam can induce bubble formation, potentially rendering cathode particles electrochemically inactive and displacing particles from their initial position. However, utilizing external pressure on a pouch cell can mitigate bubble formation and its associated effects.

25 ENERGY STORAGE↗
DOE OSTI2026

Experimental considerations and applications for time-resolved impedance on silicon-anode battery systems

Dynamic electrochemical impedance spectroscopy (dEIS) utilizes a superimposed multi-sinusoidal waveform and enables temporally resolved investigations on various electrochemical processes; however, the signal-to-noise ratio must be maximized while retaining linearity and stationarity within the system. In the present work, we probe the impact of the waveform’s total amplitude as well as the waveform and phase profiles. The equal amplitude multi-sinusoidal waveform with 35 mV total amplitude (<1 mV per frequency) and random phase profile exhibits the lowest impedance noise. This input signal is sufficient in avoiding the high frequency signal attenuation from the potentiostat’s low-pass filter. Additionally, we demonstrate the optimized dEIS waveform’s utility in investigating surface passivation within thin-film and composite silicon (Si) anodes. Within a two-electrode Si-lithium metal coin cell, the charge transfer resistance (RCT) associated with alloying kinetics dominates the overall impedance. RCT increases with state of charge indicating a kinetic bottleneck at higher lithiation states. To explore this further, we utilize a three-electrode Si-LiNi0.8Mn0.1Co0.1O2 pouch cell to deconvolute the Si impedance contributions. The evolution of the solid electrolyte interphase (SEI) and charge transfer resistances correlate to specific Li–Si alloy phases. We attribute this to the influence of Si particle volume expansion on SEI instabilities and a kinetic bottleneck at higher lithiation states.

Lam, Steven [ORNL]↗
DOE OSTI2017

Spatial atomic layer deposition for coating flexible porous Li-ion battery electrodes

Ultrathin atomic layer deposition (ALD) coatings on the electrodes of Li-ion batteries can enhance the capacity stability of the Li-ion batteries. To commercialize ALD for Li-ion battery production, spatial ALD is needed to decrease coating times and provide a coating process compatible with continuous roll-to-roll (R2R) processing. The porous electrodes of Li-ion batteries provide a special challenge because higher reactant exposures are needed for spatial ALD in porous substrates. This work utilized a modular rotating cylinder spatial ALD reactor operating at rotation speeds up to 200 revolutions/min (RPM) and substrate speeds up to 200 m/min. The conditions for spatial ALD were adjusted to coat flexible porous substrates. The reactor was initially used to characterize spatial Al2O3 and ZnO ALD on flat, flexible metalized polyethylene terephthalate foils. These studies showed that slower rotation speeds and spacers between the precursor module and the two adjacent pumping modules could significantly increase the reactant exposure. The modular rotating cylinder reactor was then used to coat flexible, model porous anodic aluminum oxide (AAO) membranes. The uniformity of the ZnO ALD coatings on the porous AAO membranes was dependent on the aspect ratio of the pores and the reactant exposures. Larger reactant exposures led to better uniformity in the pores with higher aspect ratios. The reactant exposures were increased by adding spacers between the precursor module and the two adjacent pumping modules. The modular rotating cylinder reactor was also employed for Al2O3 ALD on porous LiCoO2 (LCO) battery electrodes. Uniform Al coverages were obtained using spacers between the precursor module and the two adjacent pumping modules at rotation speeds of 25 and 50 RPM. The LCO electrodes had a thickness of ~49 um and pores with aspect ratios of ~12-25. Coin cells were then constructed using the ALD-coated LCO electrodes and were tested to determine their battery performance. The capacity of the Al2O3 ALD-coated LCO battery electrodes was measured versus the number of charge-discharge cycles. Both temporal and spatial ALD processing methods led to higher capacity stability compared with uncoated LCO battery electrodes. The results for improved battery performance were comparable for temporal and spatial ALD-coated electrodes. The next steps are also presented for scale-up to R2R spatial ALD using the modular rotating cylinder reactor.

25 ENERGY STORAGE↗
DOE OSTI2023

Optimizing Fast Charging and Wetting in Lithium-Ion Batteries with Optimal Microstructure Patterns Identified by Genetic Algorithm

To sustain the high-rate current required for fast charging electric vehicle batteries, electrodes must exhibit sufficiently high effective ionic diffusion. Additionally, to reduce battery manufacturing costs, wetting time must decrease. Both of these issues can be addressed by structuring the electrodes with mesoscale pore channels. However, their optimal spatial distribution, or patterns, is unknown. Herein, a genetic algorithm has been developed to identify these optimal patterns using a CPU-cheap proxy distance-based model to evaluate the impact of the added pore networks. Both coin-cell and pouch cell form factors have been considered for the wetting analysis, with their respective electrolyte infiltration mode. Regular hexagonal and mud-crack-like patterns, respectively, for fast charging and fast wetting were found to be optimal and have been compared with pre-determined, easier to manufacture, patterns. The model predicts that using cylindrical channels arranged in a regular hexagonal pattern is ∼6.25 times more efficient for fast charging as compared to grooved lines with both structuring strategies being restricted to a 5% electrode total volume loss. The model also shows that only a very limited electrode volume loss (1%–2%) is required to dramatically improve the wetting (5–20 times) compared to an unstructured electrode.

25 ENERGY STORAGE↗
DOE OSTI2024

Application of the Multi-Species, Multi-Reaction Model to Coal-Derived Graphite for Lithium-Ion Batteries

Graphite is a critical material used as the negative electrode in lithium-ion batteries. Both natural and synthetic graphites are utilized, with the latter obtained from a range of carbon raw materials. In this paper, efforts to synthesize graphite from coal as a domestic feedstock for synthetic graphite are reported. Domestic coal-derived graphite could address national security and energy issues by standing up domestic supply chains for battery critical materials. The performance in lithium-ion coin cells of this coal derived graphite is compared to a commercial battery-grade graphite. For the first time, a multi-species, multi-reaction (MSMR) modeling technique is applied to synthetic graphite derived from coal. Key thermodynamic, transport, and kinetic parameters are obtained for the coal derived graphite and compared to the same parameters for commercial battery-grade graphite. Modeling of synthetic graphites will allow for virtual evaluation of these materials toward production of domestically sourced graphite.

Paul, Abigail (ORCID:0000000172892069)↗
DOE OSTI2024

Impact of Pressure Distribution and Magnitude on the Performance of Lithium Metal Anodes

Li metal anodes are a critical battery technology due to their ability to substantially increase the energy density of Li-based batteries. It is well known that pressure greatly impacts the performance of a Li-metal anode. However, precisely how the pressure value and distribution of pressure affect performance is unclear. Furthermore, the solid-electrolyte interphase composition that forms under varying pressure distributions remains a key parameter for practical lithium metal anodes. In this work, different pressure distributions were employed by using differently shaped and oriented mechanical springs in the coin cells, resulting in varying contact points. Pressure-sensitive films were used to spatially map the pressure and correlate it to the performance. It was found that higher average pressure does not necessarily have a positive effect on performance. When high pressure is paired with poor pressure uniformity, the performance is in fact worse likely due to the current focusing effect, rendering unsatisfied cycling stability. This work points to the importance of controlling the relationship between average pressure and pressure uniformity.

25 ENERGY STORAGE↗
DOE OSTI2024

Electroanalytical Exploration of Li Loss at the Solid Electrolyte-Anode Interface in Anode-Free Batteries with Polymer Electrolytes

Li loss during cycling at the solid electrolyte|anode interface strongly determines the cycle life of anode-free solid-state batteries (SSBs). Here, this loss is probed electroanalytically for polymer electrolyte (PE)-based SSBs in anode-free coin cells with practical pressures. A wide range of parameters expected to impact the measured average coulombic efficiency (CE) were explored to estimate the expected range of performance. These factors include PE type, cycling profiles, current collector type, and the presence of a thin Li seed layer. Further, low CE values in the ~50%–85% range are observed for all electrolytes and test conditions. Other than the electrolyte type, a strong dependence of the CE on the electrochemical cycling profile and the type of metallic current collector is observed. Compared to the anode-free setup, the presence of a thin (5 μ m) Li seed layer did not improve the average CE for two out of three PEs, suggesting its presence to be a weak contributor in minimizing the Li loss. This work provides baseline data on the Li losses in low-pressure anode-free configuration cells with PEs.

25 ENERGY STORAGE↗
DOE OSTI2017

Ionic Liquid as an Effective Additive for Rechargeable Magnesium Batteries

Here, the effect of the addition of an ionic liquid DEME•TFSI to an electrolyte solution of Mg(HMDS) 2 -MgCl 2 in THF was studied electrochemically and spectroscopically. Reversible magnesium deposition/dissolution was achieved with the DEME•TFSI-modified electrolyte. This electrolyte shows higher ionic conductivity, and a linear relationship was observed between the ionic conductivity and the concentration of DEME•TFSI in THF solution of Mg(HMDS) 2 -MgCl 2 . Mg-Mo 6 S 8 coin cells have also been successfully cycled using Mg(HMDS) 2 -MgCl 2 electrolyte with the addition of DEME•TFSI. Raman and NMR spectroscopy suggest that DEME•TFSI facilitates magnesium deposition/dissolution by improving ionic conductivity of the electrolyte.

25 ENERGY STORAGE↗
DOE OSTI2018

Research three-dimensional hierarchical graphite architectures for anodes for fast charging

With current lithium ion batteries optimized for performance under relatively low charge rate conditions, implementation of XFC has been hindered by drawbacks including Li plating, kinetic polarization, and heat dissipation. This project will utilize model-informed design of 3-D hierarchical electrodes to tune key XFC related variables like 1) bulk porosity/tortuosity 2) vertical pore diameter, spacing, and lattice 3) crystallographic orientation of graphite particles relative to exposed surfaces 4) interfacial chemistry of the graphite surfaces through "artificial sEr formation using ALD 5) current collector surface roughness (aspect ratio, roughness factor, etc.). A key aspect of implementing novel electrodes is characterizing them in relevant settings. For this project, ultimately led out of University of Michigan by Neil Dasgupta, that includes both coin cell and 2+ Ah pouch cell testing, as well as comparison testing against baselines. Sandia National Labs will be conducting detailed cell characterization on iterative versions/improvements of the model-based hierarchical electrodes, as well as COTS cells for baseline comparisons. Key metrics include performance under fast charge conditions, as well as the absence or degree of lithium plating. Sandia will use their unique high precision cycling and rapid EIS capabilities to accurately characterize performance and any lithium plating during 6C charging and beyond, coupling electrochemical observations with cell teardown. Sandia will also design custom fixturing to cool cells during rapid charge, to decouple any kinetic effects brought about by cell heating and allow comparisons between different cells and charge rates. Using these techniques, Sandia will assess HOH electrodes from the University of Michigan, as well as aiding in iterative model and electrode design.

25 ENERGY STORAGE↗
DOE OSTI2019

Development of Ultraviolet Curable Binder Technology to Reduce Manufacturing Cost and Improve Performance of Lithium ion Battery Electrodes (Final Report)

Miltec UV International and its partners, Oak Ridge National Laboratory (ORNL) and Argonne National Laboratory (ANL) undertook this project to demonstrate the use of UV curable binder to replace conventional solvent based binders such as PVDF as a means of reducing the manufacturing cost of Lithium ion battery (LIB) electrodes. The project involved an iterative Research and Development (R&D) effort: making coin cells and pouch cells from electrodes made with varying UV chemistries and active materials, followed by testing and analyses, then by adjustments in UV chemistry, mixing, coating, and UV curing to produce layered pouch cells at high processing speeds with performance equal or greater than that of a conventional PVDF cell. The effort focused on cathodes made with UV curable binders and multiple active cathode materials such as NMC, NCA, Sulfur, and LMO and anodes made with LTO. A primary objective of the project is to provide performance data sufficient for Lithium ion battery manufacturers to commit to the first steps of making their own HEV, PHEV and/or EV Lithium ion batteries with a UV process. In addition, the project successfully demonstrated coating and UV curing a cathode layer on top of an existing UV cathode layer to produce a thicker high energy cathode with good porosity and no discontinuity between layers. It also demonstrated the potential advantages of one layer of a power loading with a second layer of an energy loading.

25 ENERGY STORAGE↗