Search NASA⌕ Search

SEARCH · Search NASA

Results for “Computational aerodynamics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Computational Fluid Dynamics-Based Modeling of Methane Flows Around Oil and Gas Equipment

Recent studies estimate that emissions from oil and gas production facilities contribute between 20 and 50% of the total methane ( CH 4 ) emitted in the US; therefore, quantifying and reducing these emissions are crucial for achieving climate goals. Methane quantification depends on both measuring methane concentrations and converting them to emissions through a modeling framework. Currently, simple atmospheric dispersion models are primarily used to quantify emissions and concentrations, but these estimates are highly uncertain when quantifying emissions from complex aerodynamic sources, such as oil and gas facilities. This investigation used a CFD modeling approach, which can account for aerodynamic complexity but has hitherto not been used to model methane concentrations downwind of a methane release of a known rate, and compared it against in situ measurements. High-time-resolution (1 Hz) methane concentration and meteorological data were measured during experiments conducted at the METEC on 21 March and 11 July 2024. The METEC site configuration, measured wind data, and controlled emission rates were used as input for the CONVERGE CFD model to model downwind CH 4 concentration. The modeling was carried out between 20 and 70 m, from two different points of release in two separate controlled-release experiments, one from a separator and another from a wellhead. In these experiments, we found that the CFD model could predict the CH 4 concentrations downwind of the release to a good degree. The model was evaluated on multiple metrics to assess its performance in estimating methane concentrations at typical fence line distances (∼30 m). These results help us to understand external flows and the ability of CFD models to predict downwind concentrations in aerodynamically complex environments.

03 NATURAL GAS↗
DOE OSTI2026

Multipoint Aerostructural Optimization of Wind Turbine Rotors Using a Coupled Blade‐Resolved Aerostructural Solver

Physics‐based design optimization workflows thread the needle between computational cost limitations and simulation complexity, often compromising between modeling detail and the range of operating design conditions. Multipoint aerostructural optimization of wind turbine rotors has so far been confined to low‐fidelity analyses or to high‐fidelity studies with simplified structural models, leaving the most complex design trade‐offs unexplored. We close this gap by performing the first tightly coupled gradient‐based multipoint aerostructural rotor optimization using 3D aerodynamic and structural solvers with discrete coupled adjoints. The optimizer simultaneously varies blade planform, airfoil shapes, and structural thickness through more than 270 design variables, minimizing a weighted combination of rotor mass and power across multiple wind speeds. Applied to a modified DTU 10‐MW benchmark under conservative structural and aerodynamic constraints, our multipoint optimization reduces rotor mass by up to 36% and increases power by 12%–15% across the main operating conditions; biasing the objective toward power yields power gains up to 18% and a 17% mass reduction. For a nominal wind distribution, 3‐point rotor designs accounting for low RPM and high thrust conditions capture dominant trade‐offs and outperform single‐point designs. Adding two off‐design points changes individual‐condition power by less than 3% but leaves the weighted average within 0.5%, and the mass‐power bias has a stronger effect on the final design than the operating‐point weighting itself. Our framework extends naturally to richer load cases and site‐specific wind distributions, providing a basis for high‐fidelity multipoint design earlier in industrial workflows.

17 WIND ENERGY↗
DOE OSTI2025

Introducing Kynema, an Open-Source Performance-Portable Flexible-Multibody-Dynamics Solver

In this talk we introduce Kynema, an open-source general flexible-multibody-dynamics solver that is well suited for simulating wind turbine structural dynamics. Kynema uses a Lie-group time integrator for constrained systems and runs on both CPUs and GPUs. Timing results for simulations are presented for the IEA 15-MW turbine with and without aerodynamic forces.

17 WIND ENERGY↗
DOE OSTI2021

Energy balance in the DSSAT-CSM-CROPGRO model

One potential way to improve crop growth models is for the models to predict energy balance and evapotranspiration (ET) from first principles, thus serving as a check on “engineered” ET methodology. In this paper, we present new implementations and the results of an energy balance model (EBL) developed by Jagtap and Jones (1989) and then implemented in DSSAT’s CROPGRO (CG-EBL) model by Pickering et al. (1995) as a linked energy balance-photosynthesis model that has not been field-tested until now. The energy balance code computes evapotranspiration and other energy balance components, as well as a canopy air temperature, based on three sources (sunlit leaves, shaded leaves, soil surface). Model performance was evaluated with measured biomass and energy fluxes from two sites in Nebraska, namely, the US-Ne2 irrigated maize-soybean rotation field and the US-Ne3 rainfed maize-soybean rotation field, which are part of the Ameriflux eddy covariance network (htt ps://ameriflux.lbl.gov/sites). After implementing new aerodynamic resistances and the stomatal conductance model of the Ball–Berry–Leuning, crop growth, evapotranspiration and soil temperature were simulated well by the EBL model. The EBL improved ET predictions slightly over the often-used FAO56 method [Penman–Monteith (Allen et al., 1998)] for 4 of the 5 years evaluated for both irrigated and rainfed conditions. Further, a significant improvement was achieved using EBL for the simulation of soil temperature at the various depths compared to STEMP, the original subroutine in DSSAT for simulating soil temperature. Compared to the other available DSSAT methods, the EBL explicitly simulates the impacts of crop morphology, physiology and management on the crop’s environment and energy and mass exchange, which in turn directly affect the water use and irrigation requirements, phenology, photosynthesis, growth, sterility, and yield of the crop.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

kynema-fmb [SWR-23-07]

Kynema-FMB (FKA: Kynema) is an open-source performance portable flexible multibody (FMB) dynamics solver designed for time-domain simulations. While originally tailored for wind turbine structural dynamics, the formulation and implementation are those of a general flexible-multidbody dynamics solver that can readily be applied to a wide range of systems. Kynema was designed with a narrow focus, namely to provide a lightweight, fast, accurate FMD solver for coupling to computational-fluid-dynamics (CFD) codes, especially the CFD codes in the Kynema suite, for fluid-structure-interaction (FSI) simulations. Kynema-FMB is equipped to model systems that can be represented as a collection of beams and rigid bodies that are connected through constraints. Degrees of freedom are defined in the inertial/global frame of reference and include displacements and rotations (formally as rotation matrices, but stored as quaternions). The underlying formulation is built on a Lie-group time integrator designed for index-3 differential-algebraic equations, which is second-order accurate in time (Bruls et al., 2012). Beam models are based on geometrically exact beam theory and are discretized as high-order spectral finite elements similar to those in BeamDyn (Wang et al., 2017). The governing equations for a FMD system like a wind turbine constitute a highly nonlinear system of constrained partial-differential equations. Kynema-FMB uses analytical Jacobians in the nonlinear-system solves in each time step. Linear systems use sparse storage and several third-party sparse-linear-system solvers are enabled. Ill conditioning of linear systems is mitigated with preconditioning described in Bottasso et al, 2008. Kynema-FMB is integrated with a simple open-source controller (ROSCO). There is an application programming interface (API) for coupling to geometry-resolved CFD (like that in Sharma et al., 2023) and actuator-force CFD (like that in Kuhn et al., 2025). In the latter, for actuator-line models, Kynema-FMB includes an internal blade-element solver that depends on user-provided lookup tables for coefficients of lift and drag, i.e., aerodynamic polars. Kynema-FMB is written in C++ and leverages Kokkos and Kokkos-Kernels (KokkosEcosystem) as its performance portability layer enabling simulations on both CPU and GPU systems. The repository is equipped with extensive automated testing at the unit and regression/system levels. The following describes the high-level development objectives conceived for Kynema: *Kynema will follow modern software development best practices, including test-driven development (TDD), version control, hierarchical automated testing, and continuous integration (CI) for a robust development environment. *The core data structures are memory efficient and enable vectorization and parallelization at multiple levels. *Data structures are data-oriented to exploit methods for accelerated computing including high utilization of chip resources (e.g., single instruction multiple data (SIMD) instruction sets) and parallelization using GP-GPUs. *The computational algorithms incorporate robust open-source libraries for mathematical operations, resource allocation, and data management. *The API design considers multiple stakeholder needs and ensure integration with existing and future ecosystems for data science, machine learning, and AI. *Kynema-FMB is written in modern C++ and leverages Kokkos as its performance-portability library with inspiration from the kynema stack.

Sprague, MichaelA.↗
DOE OSTI2022

Effect of the J-Shaped Wind Turbine Airfoil Opening Ratio and Thickness on the Performance of Symmetrical Airfoils

Abstract In this work, the effect of the inner opening ratio on the J-shaped airfoils aerodynamic performance was studied and documented for symmetrical airfoils. Three different airfoil thicknesses were investigated: small (NACA0008), medium (NACA0015), and large (NACA0024). For each airfoil thickness, effects of three inner opening ratios were analyzed: one-third, one-half, and two-thirds. The performance of each opening ratio was compared with the performance of the solid airfoil “zero opening ratio” for different angles of attack between 5 deg and 20 deg. All designs were simulated using the computational fluid dynamics (CFD) technology against experimental results for solid NACA4412 airfoil in the University of Wisconsin-Milwaukee (UWM) wind tunnel facility and other published experimental data. It was found that large eddy simulation yields accurate solutions with a smaller number of mesh cells compared to the k–ω turbulence model but with much longer computational time. The lift-to-drag ratio for all studied airfoils has a maximum value for solid airfoils compared to those equipped with openings. For airfoils equipped with 00.00% opening ratio “solid,” NACA0015 airfoil has the maximum lift-to-drag ratio. Furthermore, it was found that NACA0008 equipped with a 33.33% opening ratio has the best performance of all studied J-shaped airfoils.

Energy & Fuels↗
DOE OSTI2020

Code-verification techniques for hypersonic reacting flows in thermochemical nonequilibrium

The study of hypersonic flows and their underlying aerothermochemical reactions is particularly important in the design and analysis of vehicles exiting and reentering Earth's atmosphere. Computational physics codes can be employed to simulate these phenomena; however, code verification of these codes is necessary to certify their credibility. To date, few approaches have been presented for verifying codes that simulate hypersonic flows, especially flows reacting in thermochemical nonequilibrium. In this work, we present our code-verification techniques for verifying the spatial accuracy and thermochemical source term in hypersonic reacting flows in thermochemical nonequilibrium. Additionally, we demonstrate the effectiveness of these techniques on the Sandia Parallel Aerodynamics and Reentry Code (SPARC).

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

Modeling Exhaust-Generated Aerodynamic Pressure Loads on Airfield Matting Repair Systems

Airfield matting systems are commonly used for rapid repair of damaged runways to facilitate continuity of critical operations. Under normal service conditions, matting repair systems are subject not only to wheel loads exerted by airfield traffic but also to aerodynamic pressure loads resulting from high-speed, turbulent exhaust plumes produced by jets during taxi and take-off. Matting systems employed by the U.S. Air Force have been tested with respect to wheel loads, but probabilities of failure because of pressure loads produced by jet exhaust have not yet been established. This study presents a numerical approach for preliminary estimation of worst-case matting anchor forces resulting from exhaust-generated pressure loads. Using a two-dimensional computational fluid dynamics model, system behavior is evaluated by means of a parametric study of six system variables, of which the most significant are: (1) distance between engine and matting, (2) depth of cavity openings at matting edges, and (3) engine exhaust velocity. The results demonstrate that matting systems are likely to experience net uplift in typical service scenarios, driven by the combined effects of flow separation and cavity pressurization. Worst-case anchor pull-out forces, computed according to a tributary-area approach, are estimated to fall in the range of 130 lb (581 N) to 979 lb (4,350 N), depending on assumed load-sharing behavior among anchors and the size of the repair site. Field testing of instrumented matting systems during jet taxi and take-off sequences is recommended as the best next step toward understanding system behavior.

Engineering↗
DOE OSTI2023

Aerodynamic Rotor Design for a 25 MW Offshore Downwind Turbine

Continuously increasing offshore wind turbine scales require rotor designs that maximize power and performance. Downwind rotors offer advantages in lower mass due to reduced potential for tower strike, and is especially true at large scales, e.g., for a 25 MW turbine. In this study, three 25 MW downwind rotors, each with different prescribed lift coefficient distributions were designed (chord, geometry, and twist) and compared to maximize power production at unprecedented scales and Reynolds numbers, including a new approach to optimize rotor tilt and coning based on aeroelastic effects. To achieve this objective the design process was focused on achieving high power coefficients, while maximizing swept area and minimizing blade mass. Maximizing swept area was achieved by prescribing pre-cone and shaft tilt angles to ensure the aeroelastic orientation when the blades point upwards was nearly vertical at nearly rated conditions. Maximizing the power coefficient was achieved by prescribing axial induction factor and lift coefficient distributions which were then used as inputs for an inverse rotor design tool. The resulting rotors were then simulated to compare performance and subsequently optimized for minimum rotor mass. To achieve these goals, a high Reynolds number design space was developed using computational predictions as well as new empirical correlations for flatback airfoil drag and maximum lift. Within this design space, three rotors of small, medium and large chords were considered for clean airfoil conditions (effects of premature transition were also considered but did not significantly modify the design space). The results indicated that the medium chord design provided the best performance, producing the highest power in Region 2 from simulations while resulting in the lowest rotor mass, both of which support minimum LCOE. The methodology developed herein can be used for the design of other extreme-scale (upwind and downwind) turbines.

downwind rotors↗
DOE OSTI2026

FOILPOLARS (Grassmannian Foil Shape Sweeps for Polar Generation) [SWR-26-095]

FOILPOLARS (Grassmannian Foil Shape Sweeps for Polar Generation): Multifidelity aerodynamic polar data generation for hydrofoil/tidal-turbine airfoil sections. Foilpolars ties together three pieces: *AeroSandbox supplies the baseline airfoil coordinates (UIUC database). *G2Aero parameterizes those shapes on a Grassmannian manifold (Karcher mean + PGA basis) and samples new perturbed shapes around that basis. *XFoil (panel method) and NeuralFoil (neural-network surrogate, shipped with AeroSandbox) each solve the resulting shapes for lift, drag, moment, and pressure at the swept angles of attack, Reynolds numbers, and n_crit values. Design optimization of foil shapes in a computationally efficient way requires polars data across many candidate shapes, not just a handful of baseline foils. However, high-fidelity CFD at that scale is too costly, and naive shape perturbation strays from realistic geometries. FOILPOLARS addresses this by loading baseline airfoils (via AeroSandbox) and mapping them onto a Grassmannian manifold (via G2Aero), computing a Karcher mean and principal geodesic analysis (PGA) basis. New shapes are sampled by perturbing PGA coefficients, keeping them close to the manifold of realistic foils. Each sampled shape is evaluated across a configurable sweep of angle of attack, Reynolds number, and critical amplification factor using two solvers: XFoil (panel method) and NeuralFoil (neural-network surrogate), producing a paired dataset of lift, drag, moment, pressure, convergence, and confidence, indexed alongside each shape's PGA coefficients and shared Grassmannian basis in a single xarray dataset. From this, FOILPOLARS produces convergence summaries and comparison plots per shape, Reynolds number, and n_crit. A command-line interface exposes each pipeline stage independently, supporting data-driven design, optimization, and machine-learning workflows for foils.

Sandhu, Rimple [National Laboratory of the Rockies↗
DOE OSTI2024

Multiphysics Design Optimization and Additive Manufacturing of Nuclear Components (Final CRADA Report - Executive Summary)

Westinghouse Electric Company (WEC) actively participated in the advancement of the nuclear fuel and reactor design space and requested the help of Oak Ridge National Laboratory (ORNL) in the creation of a new design tool set. This report details the creation of a collection of software tool sets that are linked together to collectively assist WEC design engineers in developing novel ideas outside the normal scope of traditional nuclear fuel and reactor design formulas. Specifically, Siemens HEEDS, a design space exploration and parametric optimization software, monitored and changed parameters in a collection of softwares to meet the team’s objective. The HEEDS parametric optimization method, SHERPA, was developed to control the Siemens NX CAD platform to adjust the native CAD of a hexahedral spacer grid. This new geometry can be used to execute a topological design optimization by the NX Topology software add-in. The resulting geometry is additively manufacturable. This topological optimization occurred twice—once on the spacer grid’s spring, and once on the dimple geometry. These new geometries were imported by Siemens’ STAR-CCM+, a multiphysics structural and fluid dynamic computational solver in which the spring geometry is deflected to match the rod insertion configuration. Along with the dimple geometry, this new deflected spring was used to complete a hydraulic assessment of a single-unit cell comprising one rod, one spring, and two dimples. The HEEDS SHERPA algorithm ranks the design based on the final mass of the unit cell and the hydraulic pressure drop performance. The ORNL team demonstrated the ability to use this software and provided engineering judgement to apply modern aerospace aerodynamic design. The effort has been focused on thinking outside the conventional design space and redesigning a spacer grid to perform beyond the WEC set objectives. Furthermore, the ORNL team also demonstrated that the HEEDS optimization routine can independently develop a design that meets the WEC design goals. Although these designs were at a low technology readiness level, their demonstration confirmed the team’s capability to create novel advanced nuclear concepts.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Regularizing Invertible Neural Networks for Airfoil Design Through Dimension Reduction

This work examines how dimension reduction can improve the performance of invertible neural networks (INN) for airfoil design. Design workflows are typically expensive, relying on many evaluations of high fidelity computational fluid dynamics (CFD) models. Furthermore, the inverse design problem is typically ill-posed. That is, multiple valid solutions exist that satisfy the design criteria. Regularization can reduce this inverse design space and simplify the problem. We study the use of subspace-based input dimension reduction to act as a regularizer for the INN model and improve the recovery of new airfoil shapes with desired performance characteristics. We find that the dimension reduction identifies two dominant modes, relating to airfoil thickness and camber, that optimally determine the airfoil's aerodynamics. We demonstrate the capability of the proposed INN model to generate 100 airfoils that satisfy the specific aerodynamic and structural characteristics.

airfoil design↗
DOE OSTI2020

Drag Coefficient Analysis of Arbitrary Fragment Geometry with Emphasis on Meshing Sensitivity Studies.

This report characterizes Mach number effects in the hypersonic range from Mach 3 to Mach 7 for an arbitrary, computationally generated fragment. Force and moment coefficients in the x, y, z direction were successfully obtained and resulting trends were compared with theoretical expectations. Three orientations were tested in the form of unit vectors: [1,0,0], [0,1,0], and [0,0,1]; these represent the i, j, k principle axes. The final results ultimately showcased a trend very similar to that shown in previous literature — drag coefficients for a given orientation decreased with increasing Mach number by a very small amount in the hypersonic range. It was therefore concluded that the aerodynamic quantities used to obtain the fragment trajectory at low hypersonic Mach numbers (such as Mach 3) can be used to characterize the aerodynamic qualities at higher hypersonic Mach numbers (Mach 5, 7) with a reasonably small margin. A sensitivity study was also conducted which ultimately defined drag effects as a result of changing grid spacing and normal extrusion parameters for the unstructured tetrahedral mesh used in the simulation. Further work can be done in the form of experimental validation, specifically with regards to wind tunnels and ballistic range testing. Error can be reduced by testing more mesh variabilities and capturing a larger amount of fragment orientations. The results for force and moment characteristics dependent on meshing parameters and high Mach numbers are satisfactory and consistent with expected trends.

42 ENGINEERING↗
DOE OSTI2025

Size-Resolved Chemical Composition of Particles Collected Using STAC at the Ground Site During the SAIL Campaign in Gunnison, Colorado

Aerosol particles were collected using a four-stage Size and Time-resolved Aerosol Collector (STAC) during the SAIL field campaign. Each stage of STAC separates particles into distinct aerodynamic size fractions with 50% cut-off diameters: Stage A: 2.27 µm Stage B: 0.615 µm Stage C: 0.421 µm Stage D: 0.119 µm Each stage provides both size- and time-resolved sampling, enabling investigation of particle composition across different atmospheric regimes. Only a subset of samples was selected for analysis based on prevailing meteorological conditions (e.g., temperature, humidity, and air-mass influence) to capture representative aerosol types under distinct weather patterns. Collected substrates were first examined under Scanning Electron Microscopy (SEM) to evaluate particle loading, morphology, and spatial distribution. Subsequently, Computer-Controlled Scanning Electron Microscopy with Energy-Dispersive X-ray Spectroscopy (CCSEM/EDX) was performed to obtain size-resolved elemental composition of individual particles. A rule-based classification scheme was applied to categorize particles into major compositional groups (e.g., biological, carbonaceous, dust, sulfate, Na-rich, and mixed types). This dataset provides high-resolution morphological and chemical information on atmospheric particles collected during the SAIL campaign, offering insights into the influence of meteorology on aerosol composition and mixing state.

Size and Time-resolved Aerosol Collector↗
DOE OSTI2023

An Integrated Platform for Wind Power Plant Operations: From Atmosphere to Electrons to the Grid (A2e2g)

The research objective for the Atmosphere to Electrons to the Grid (A2e2g) project was to design a platform that merges forecasting tools with aerodynamic and economic models. The value proposition is that expanding wind power plant operation to include grid services allows those plants to operate in markets for grid services as well as energy markets, increasing revenue streams for wind plant operators while contributing to reliable grid operation.

17 WIND ENERGY↗
DOE OSTI2024

One-to-one aeroservoelastic validation of operational loads and performance of a 2.8 MW wind turbine model in OpenFAST

Abstract. This article presents a validation study of the popular aeroservoelastic code suite OpenFAST leveraging weeks of measurements obtained during normal operation of a 2.8 MW land-based wind turbine. Measured wind conditions were used to generate one-to-one turbulent flow fields (i.e., comparing simulation to measurement in 10 min increments, or bins) through unconstrained and constrained assimilation methods using the kinematic turbulence generators TurbSim and PyConTurb. A total of 253 bins of 10 min of normal turbine operation were selected for analysis, and a statistical comparison in terms of performance and loads is presented. We show that successful validation of the model was not strongly dependent on the type of inflow assimilation method used for mean quantities of interest, which had median modeling errors per wind-speed interval generally within 5 %–10 % of the measurement. The type of inflow assimilation method did have a larger effect on the fatigue predictions for blade-root flapwise and tower-base fore–aft quantities, which surprisingly saw larger errors from the assumed higher-fidelity assimilation methods. Avenues for further work are discussed and include possible improvements to the aerodynamic, structural, and controller modeling that may offer insight on the origin of the up to ∼ 40 % median overprediction of fatigue for these quantities.

17 WIND ENERGY↗
DOE OSTI2026

Optimization techniques in self-similar compressible flow

We investigate the one-dimensional (1D) inviscid compressible flow equations for an ideal gas through the lens of optimization techniques. It is the case that, to our knowledge, optimization analysis applied to the so-called “linear velocity” solutions of the Euler compressible flow equations has not been previously conducted. Through both gradient-based and variational techniques, new variants of well-studied flow scenarios, i.e., self-similar, 1D, linear velocity solution class to idealized inviscid compressible flow equations, are determined, as encoded in both the kinematic and thermodynamic properties of this self-similar solution class. With the kinematics of the said solutions being driven by a self-similar “scale radius” and the thermodynamics being driven separately through the appearance of an arbitrary function, a myriad of new solution classes is possible. Acting as a guide to more realistic physical circumstances as well as discovery, it is the hope that the presented cases serve as the framework for future investigations into the intersection of self-similarity and optimization techniques. Fields of study that may find this work to be of interest include aerodynamic design, flow control, inertial confinement fusion, physics-informed neural networks, and other related areas of interest.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗