Search NASA⌕ Search

SEARCH · Search NASA

Results for “Correlation of Full-Scale”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1997

Experimental Investigation of a Graphite-Composite Intertank Section for a Reusable Launch Vehicle

The use of graphite-composites as primary structure is essential for the development of a cost effective single-stage-to-orbit reusable launch vehicle (RLV). A full-scale segment of a graphite-composite intertank was designed and fabricated by an industry team and tested at NASA Langley Research Center as a part of the RLV technology development program. The intertank test component was approximately 3.0 m long by 6.7 m wide and included slightly less than a 90deg section of a cylindrical intertank. The test article was fabricated using graphite-bismaelimide composite material and consisted of a hat-stiffened skin with five ring frames. The stiffeners were secondarily bonded to the panel skin and the ring frames were mechanically attached. The test article was loaded to failure with a uniform compression load applied by 21 individually controlled hydraulic actuators. Resistance strain gages, linear variable differential transformers and video cameras were used to measure and record the test results. A linear f d t e element analysis of the test article and test fixture was performed. The test results verified the structural integrity cf the intertank test article up to the design limit load. However, the test article failed in general skin buckling between the ring frames at a load 1.08 times design limit load. This load was considerably lower than the expected failure load. The cause of premature failure is being investigated. Good correlation of the test and analysis results was obtained for loads up to the design limit load.

Sawyer, James Wayne↗
NASA NTRS1973

Shockwave-boundary layer interference heating analysis.

Interference heating correlations have been developed based on existing wind tunnel test data taken with simple configurations such as wedge/flat plate and compression corner models. For turbulent flow, peak interference heating was first correlated with shock strength (pressure ratio across shock wave) and then as a function of Reynolds number. The peak interference Stanton number was found to exhibit the same Reynolds number and Prandtl number characteristics as the Stanton number variation for undisturbed flow over a flat plate. Similar correlations were developed for laminar flow. Results indicated that for laminar flow at higher Reynolds number, the impinging shockwave may act as a boundary layer trip and cause boundary layer transition resulting in high interference heating. The correlations derived in this study can be used to scale wind tunnel model test data to a full-scale space vehicle at supersonic or hypersonic flight conditions.

Hung, F. T.↗
NASA NTRS1974

Investigation of noise from full-scale high bypass engine and blown flap system

A summary is presented of an acoustic test program for investigating engine noise suppression and jet/flap interaction noise associated with an EBF STOL powered lift system. A highly suppressed TF-34 engine and EBF wing were used in the investigation. The engine was suppressed 21 PndB to a level of 94 PndB. An UTW powered lift system was tested with conventional, mixer, and decayer-type nozzles. The configuration with velocity decayer nozzle and acoustically treated shroud had the lowest noise (98 PndB). An OTW configuration with non-decayer nozzle was about 10 db quieter than the corresponding UTW system. UTW and OTW noise data are compared with scale model correlations.

Jones, W. L.↗
NASA NTRS1974

Geometry considerations for jet noise shielding with CTOL engine-over-the-wing concept

Jet noise shielding benefits for CTOL engine-over-the-wing installations were obtained with various model-scale circular nozzles and wing chord geometries. Chord-to-nozzle diameter ratios were varied from 3 to 20, while ratios of nozzle height above the wing to the diameter were varied from near zero to 3. Spectral noise data were obtained with jet velocities from 640 to 1110 ft/sec. Characteristics of low frequency noise sources are discussed. Jet-noise shielding is correlated in terms of acoustic and geometric parameters. Implications of extending the model-scale data to full-scale are discussed.

Vonglahn, U.↗
NASA NTRS1974

Geometry considerations for jet noise shielding with CTOL engine-over-the-wing concept

Jet noise shielding benefits for CTOL engine-over-the-wing installations were obtained with various model-scale circular nozzles and wing chord geometries. Chord-to-nozzle diameter ratios were varied from 3 to 20, while ratios of nozzle height above the wing to the diameter were varied from near zero to 3. Spectral noise data were obtained with jet velocities from 640 to 1110 ft/sec. Characteristics of low frequency noise sources are discussed. Jet-noise shielding is correlated in terms of acoustic and geometric parameters. Implications of extending the model-scale data to full-scale are discussed.

Von Glahn, U.↗
NASA NTRS1974

Investigation of noise from full-scale high bypass engine and blown flap system

A summary is presented of an acoustic test program for investigating engine noise suppression and jet/flap interaction noise associated with an externally blown flap (EBF) STOL powered lift system. A highly suppressed TF-34 engine and EBF wing were used in the investigation. The engine was suppressed 21 PndB to a level of 94 PndB. An under the wing (UTW) powered lift system was tested with conventional, mixer, and decayer-type nozzles. The configuration with velocity decayer nozzle and acoustically treated shroud had the lowest noise (98 PndB). An over the wing (OTW) configuration with nondecayer nozzle was about 10 dB quieter than the corresponding UTW system. UTW and OTW noise data are compared with scale model correlations.

Jones, W. L.↗
NASA NTRS1982

Effects of wing-leading-edge modifications on a full-scale, low-wing general aviation airplane: Wind-tunnel investigation of high-angle-of-attack aerodynamic characteristics

Wing-leading-edge modifications included leading-edge droop and slat configurations having full-span, partial-span, or segmented arrangements. Other devices included wing-chord extensions, fences, and leading-edge stall strips. Good correlation was apparent between the results of wind-tunnel data and the results of flight tests, on the basis of autorotational stability criterion, for a wide range of wing-leading-edge modifications.

Newsom, W. A., Jr.↗
NASA NTRS1982

The need for an optical transition detection system in the NTF

Methods for transition detection were studied. The very high test and model costs necessitate testing of any new configuration over a range of Reynolds numbers for correlation with data obtained in conventional tunnels. The Reynolds number variations will be carried out at constant dynamic pressure, i.e., constant aeroelastic condition, by varying test temperature. Boundary layer transition cannot be expected to occur at the full scale location at significantly less than full-scale Reynolds numbers, and transition patterns will change with varying Reynolds number. Knowledge of the location of transition on model surfaces is essential for correct interpretation of drag data. The importance of transition, the limitations of artificial transition fixing, and their relation to the NTF are reviewed. The calculated minimum roughness height to instantaneously trip transition on a model transport wing over a range of Reynolds numbers of interest is shown in the NTF.

Fancher, M. F.↗
NASA NTRS1987

Comparing Test Data on Scale-Model Helicopter Rotors

Hovering data correlate well, but forward-flight data do not. Report compares acoustics and performance of small-scale helicopter rotor with those of full-scale rotor in both hovering and forward flight.

Kitaplioglu, Cahit↗
NASA NTRS1988

Use of Dynamically Scaled Models for Studies of the High-Angle-of-Attack Behavior of Airplanes

Dynamically scaled, free-flying models are used by the National Aeronautics and Space Administration (NASA) to study the stalling and spinning characteristics of civil and military airplane configurations. Such tests have been conducted for many different designs, and it has been possible to correlate the results predicted by the model tests with flight test results obtained in the investigations. The present paper describes four of the dynamic model testing techniques used at the NASA Langley Research Center, including the scaling laws used in the construction of models and in the interpretation of results. Predictions of stall/spin behavior based on model results have generally been very accurate, and the model tests are regarded as an invaluable precursor to full-scale flight tests. However, aerodynamic scale effects between some models and full-scale airplanes due to differences in test values of Reynolds number have resulted in erroneous predictions for a few configurations. A discussion of these effects is provided, together with the approach used to modify the model so that its behavior more closely matches that of the airplane. Finally, two typical applications of the techniques to the X-29A research airplane and several general aviation research airplanes are presented to illustrate the type of information provided by the tests.

Joseph R Chambers↗
NASA NTRS1988

Use of dynamically scaled models for studies of the high-angle-of-attack behavior of airplanes

Dynamically scaled, free-flying models are used by the National Aeronautics and Space Administration (NASA) to study the stalling and spinning characteristics of civil and military airplane configurations. Such tests have been conducted for many different designs, and it has been possible to correlate the results predicted by the model tests with flight test results obtained in the investigations. The present paper describes four of the dynamic model testing techniques used at the NASA Langley Research Center, including the scaling laws used in the construction of models and in the interpretation of results. Predictions of stall/spin behavior based on model results have generally been very accurate, and the model tests are regarded as an invaluable precursor to full-scale flight tests. However, aerodynamic scale effects between some models and full-scale airplanes due to differences in test values of Reynolds number have resulted in erroneous predictions for a few configurations. A discussion of these effects is provided, together with the approach used to modify the model so that its behavior more closely matches that of the airplane. Finally, two typical applications of the techniques to the X-29A research airplane and several general aviation research airplanes are presented to illustrate the type of information provided by the tests.

Joseph R Chambers↗
NASA NTRS1990

Predictions of F-111 TACT aircraft buffet response

A summary is presented for the prediction method development and correlations of predicted response with flight test measurements. The prediction method was based on refinements to the method described by Cunningham. One improvement made use of direct time integration of the correlated fluctuating pressure data to obtain buffet excitation for the various modes of interest. Another improvement incorporated a hybrid technique for scaling measured wind tunnel damping data to full-scale for the modes of interest. A third improvement made use of the diagonalized form of the fully coupled equations of motion. Finally, a mechanism was described for explaining an apparent coupling between the aircraft wing torsion modes and shock induced trailing edge separation that led to very high wing motion on the aircraft that was not observed on the wind tunnel model.

Cunningham, Atlee M., Jr.↗
NASA NTRS1992

Aerodynamic roughness measured in the field and simulated in a wind tunnel

This study evaluates how well values of aerodynamic surface roughness, z sub 0, measured over scale models in wind tunnels correlate with values of z sub 0 measured at full scale in the field. A field experiment was conducted in which values of z sub 0 and u* (wind friction speed) were measured over three arrays of non-erodible roughness elements on a dry lake bed. Wind profiles were measured by ten anemometers on a 15 m mast under thermally neutral atmospheric conditions. Values of z sub 0 increased from .00014 m (dry lake bed only) to .026 m with increasing roughness element density. The three roughness element arrays were simulated at 1/10 and 1/20 scale in an open-circuit atmospheric boundary-layer wind tunnel. Velocities were measured with a boundary-layer pitot-tube rake from the same relative position within the scale model arrays as the anemometers were relative to the field arrays. Each array at each scale was sampled three times at five freestream velocities. Average values of z sub 0 for each model array at each scale were compared with full-scale values of z sub 0 obtained in the field. The field vs. wind tunnel correspondence of z sub 0 is found to be z sub 0 field = 0.2661 x (z sub(0 model) x scale(exp -1))exp .8159.

Sullivan, Robert↗
NASA NTRS1994

Theoretical study of the effect of an AlGaAs double heterostructure on metal-semiconductor-metal photodetector performance

The sizing and efficiency of an aircraft is largely determined by the performance of its high-lift system. Subsonic civil transports most often use deployable multi-element airfoils to achieve the maximum-lift requirements for landing, as well as the high lift-to-drag ratios for take-off. However, these systems produce very complex flow fields which are not fully understood by the scientific community. In order to compete in today's market place, aircraft manufacturers will have to design better high-lift systems. Therefore, a more thorough understanding of the flows associated with these systems is desired. Flight and wind-tunnel experiments have been conducted on NASA Langley's B737-100 research aircraft to obtain detailed full-scale flow measurements on a multi-element high-lift system at various flight conditions. As part of this effort, computational aerodynamic tools are being used to provide preliminary flow-field information for instrumentation development, and to provide additional insight during the data analysis and interpretation process. The purpose of this paper is to demonstrate the ability and usefulness of a three-dimensional low-order potentialflow solver, PMARC, by comparing computational results with data obtained from 1/8 scale wind-tunnel tests. Overall, correlation of experimental and computational data reveals that the panel method is able to predict reasonably well the pressures of the aircraft's multi-element wing at several spanwise stations. PMARC's versatility and usefulness is also demonstrated by accurately predicting inviscid threedimensional flow features for several intricate geometrical regions.

Salem, Ali F.↗
NASA NTRS1995

Three-dimensional aerodynamic analysis of a subsonic transport high-lift configuration and comparisons with wind-tunnel test results

The sizing and efficiency of an aircraft is largely determined by the performance of its high-lift system. Subsonic civil transports most often use deployable multi-element airfoils to achieve the maximum-lift requirements for landing, as well as the high lift-to-drag ratios for take-off. However, these systems produce very complex flow fields which are not fully understood by the scientific community. In order to compete in today's market place, aircraft manufacturers will have to design better high-lift systems. Therefore, a more thorough understanding of the flows associated with these systems is desired. Flight and wind-tunnel experiments have been conducted on NASA Langley's B737-100 research aircraft to obtain detailed full-scale flow measurements on a multi-element high-lift system at various flight conditions. As part of this effort, computational aerodynamic tools are being used to provide preliminary flow-field information for instrumentation development, and to provide additional insight during the data analysis and interpretation process. The purpose of this paper is to demonstrate the ability and usefulness of a three-dimensional low-order potential flow solver, PMARC, by comparing computational results with data obtained from 1/8 scale wind-tunnel tests. Overall, correlation of experimental and computational data reveals that the panel method is able to predict reasonably well the pressures of the aircraft's multi-element wing at several spanwise stations. PMARC's versatility and usefulness is also demonstrated by accurately predicting inviscid three-dimensional flow features for several intricate geometrical regions.

Edge, D. Christian↗
NASA NTRS1999

Evaluation of a Scaling Approach for Stiffened Composite Flat Panels Loaded in Compression

Results of an experimental study of the effects of geometric scaling on a graphite-epoxy flat stiffened-skin panel concept loaded in compression are presented. The scaled models were fabricated using an approach to laminate thickness scaling, referred to as the "ply-thickness method." The structural response and failure characteristics of full-, half-, and quarter-scale specimens fabricated with this scaling concept are discussed and compared. The scaled up failure loads of the half- and quarter-scale models agree well with the failure load of the full-scale prototypes tested. The strength scale effects observed in the results were substantially smaller than those in earlier studies that employed other laminate scaling techniques. The experimental results indicate that failure initiated by crippling and delamination in the cap of the longitudinal stiffeners and skin-stiffener separation at the bond-lines, and was followed by failure of the specimen skin. Nonlinear finite element analysis results correlate well with experimental results up to failure.

Rouse, Marshall↗
NASA NTRS1999

Acoustic Treatment Design Scaling Methods: Advanced Treatment Impedance Models for High Frequency Ranges - Volume 2

The primary purpose of this study is to develop improved models for the acoustic impedance of treatment panels at high frequencies, for application to subscale treatment designs. Effects that cause significant deviation of the impedance from simple geometric scaling are examined in detail, an improved high-frequency impedance model is developed, and the improved model is correlated with high-frequency impedance measurements. Only single-degree-of-freedom honeycomb sandwich resonator panels with either perforated sheet or "linear" wiremesh faceplates are considered. The objective is to understand those effects that cause the simple single-degree-of- freedom resonator panels to deviate at the higher-scaled frequency from the impedance that would be obtained at the corresponding full-scale frequency. This will allow the subscale panel to be designed to achieve a specified impedance spectrum over at least a limited range of frequencies. An advanced impedance prediction model has been developed that accounts for some of the known effects at high frequency that have previously been ignored as a small source of error for full-scale frequency ranges.

Kraft, R. E.↗
NASA NTRS1947

Correlation of the Trim Limits of Stability Obtained for a PB2Y-3 Flying Boat and a 1/8-Size Powered Dynamic Model

Tests of a PB2Y-3 flying boat were made at the U.S> Naval Air Station, Patuxent River, Md., to determine its hydrodynamic trim limits of stability. Corresponding tests were also made of a 1/8-size powered dynamic model of the same flying boat in Langley tank no. 1. During the tank tests, the full-size testing procedure was reproduced as closely as possible in order to obtain data for a direct correlation of the results. As a nominal gross load of 66,000 pounds, the lower trim limits of the full-size and model were in good agreement above a speed of 80 feet per second. As the speed decreased below 80 feet per second, the difference between the model trim limits and full-scale trim limits gradually became larger. The upper trim limit of the model with flaps deflected 0 deg was higher than that of the full-size, but the difference was small over the speed range compared. At flap deflections greater than 0 deg, it was not possible to trim either the model of the airplane to the upper limit with the center of gravity at 28 percent of the mean aerodynamic chord. The decrease in the lower trim limits with increase in flap deflection showed good agreement for the airplane and model. The lower trim limits obtained at different gross loads for the full-size airplane were reduced to approximately a single curve by plotting trim against the square root of C(sub delta (sub o)) divided by C(sub V).

Garrison, Charlie C.↗