Search NASA⌕ Search

SEARCH · Search NASA

Results for “DAMPER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Non-linear performance of a three-bearing rotor incorporating a squeeze-film damper

This paper is concerned with the non-linear vibration performance of a rigid rotor supported on three bearings, one being surrounded by a squeeze-film damper. This damper relies on the pressure built up in the squeeze film to help counter-act external forces arising from unbalance and other effects. As a result a vibration orbit of a certain magnetude results. Such vibration orbits illustrate features found in other non-linear systems, in particular sub-harmonic resonances and jump phenomena. Comparisons between theoretical prediction and experimental observations of these phenomena are made.

Holmes, R.↗
NASA NTRS1986

Test results for sawtooth-pattern damper seals - Leakage and rotordynamic coefficients

Test results consisting of direct and transverse force coefficients are presented for eleven sawtooth-pattern damper-seal configurations. The designation 'damper' seal refers to a seal which uses a deliberately roughened stator and smooth rotor to increase the net seal damping force. The designation 'sawtooth-pattern' refers to a stator-roughness pattern whose cross section normal to the axis of the seal resembles saw teeth with the teeth direction opposing fluid motion in the direction of shaft rotation. The sawtooth pattern yields axial grooves in the stator which are interrupted by spacer elements which act as flow constrictions or 'dams'. Sawtooth-pattern seals had more damping than smooth seals but less than the round-hole-pattern seals tested previously. If damping is sacrificed, sawtooth-pattern seals can be designed to leak less than round-hole-pattern seals.

Childs, D.↗
NASA NTRS1989

Damper Of Small Vibrations

Vibration damper has no rubbing parts. Thus eliminates even very small static frictional forces and therefore responds to and damps extremely low levels of vibration. Damper dissipates vibration by motion of piston in volume of silicone oil. Coaxial rigid shaft holds upper and lower bellows at constant length while piston vibrates up and down. Although volumes of upper and lower bellows change continually, total volume of bellows assembly stays same.

Davis, L. P.↗
NASA NTRS1989

Cavitation effects on the pressure distribution of a squeeze film damper bearing

High speed motion pictures have revealed several operating regimes in a squeeze film damper. Pressure measurements corresponding to these distinct regimes were made to examine their effect on the performance of such dampers. Visual observation also revealed the means by which the pressure in the feed groove showed higher amplitudes than the theory predicts. Comparison between vapor and gaseous cavitation are made based on their characteristic pressure wave, and the effect this has on the total force and its phase.

Zeidan, Fouad Y.↗
NASA NTRS1989

Eddy current damper

A high torque capacity eddy current damper used as a rate limiting device for a large solar array deployment mechanism is discussed. The eddy current damper eliminates the problems associated with the outgassing or leaking of damping fluids. It also provides performance advantages such as damping torque rates, which are truly linear with respect to input speed, continuous 360 degree operation in both directions of rotation, wide operating temperature range, and the capability of convenient adjustment of damping rates by the user without disassembly or special tools.

Ellis, R. C.↗
NASA NTRS1991

Model Of Bearing With Hydrostatic Damper

Improved mathematical model of rotational and vibrational dynamics of bearing package in turbopump incorporates effects of hydrostatic damper. Part of larger finite-element model representing rotational and vibrational dynamics of rotor and housing of pump. Includes representations of deadband and nonlinear stiffness and damping of ball bearings, nonlinear stiffness and damping of hydrostatic film, and stiffness of bearing support. Enables incorporation of effects of hydrostatic damper into overall rotor-dynamic mathematical model without addition of mathematical submodel of major substructure.

Goggin, David G.↗
NASA NTRS1991

Testing and application of a viscous passive damper for use in precision truss structures

A passive damping device intended to replace individual struts in precision truss structures for space applications is described. The theory of operation of the D-Strut device is detailed, and simple five- and three-parameter models are derived. Results from tests conducted to characterize the D-Strut at submicron displacement levels are reporeted. The incorporation of a strut in a precision truss testbed is described. Parameters determined from the component-level tests are used in a finite element model of the truss, and damping augmentation is predicted. Using the simple three-parameter model, a damper is selected for multiple placement in a separate optical interferometer truss testbed. The effect of the addition of the damper struts is illustrated analytically in a model of the structure. Finally, an improved Arched Flexure D-Strut that is expected to provide higher loss factors, and is currently under development, is described.

Trubert, M.↗
NASA NTRS1991

Effectiveness of large booms as nutation dampers for spin stabilized spacecraft

The issue of using long slender booms as pendulous nutation damping devices on spinning aircraft is discussed. Motivation comes from experience with the Galileo Spacecraft, whose magnetometer boom also serves as a passive nutation damper for the spacecraft. Performance analysis of a spacecraft system equipped with such systems are relatively insensitive to changes in the damping constant of the device. However, the size and arrangement of such a damper raises important questions concerning spacecraft stability in general.

Eke, F. O.↗
NASA NTRS1991

The Effects of Manufacturing Tolerances on the Vibration of Aero-engine Rotor-damper Assemblies

A range of rotor assemblies incorporating one and two squeeze film dampers with various static misalignments is investigated. Waterfall diagrams are constructed which demonstrate the effects of such misalignment and damper support flexibility on the nature and severity of subsynchronous resonance and jump phenomena. Vibration signatures of similar rotor-bearing assemblies are shown to contrast strongly due to different accumulations of tolerances during manufacture, fitting, and operation.

Sykes, J. E. H.↗
NASA NTRS1992

Motion of a spacecraft with magnetic damper

Three methods of numerically simulating the motion of a spacecraft with a magnetic damper are compared. Simulations of motion of the initial assembly stage of Space Station Freedom show that results obtained with the first approach are in general agreement with those based on the second approach, while results from the third method are incorrect unless the spacecraft is nearly at rest in a local-vertical-local-horizontal reference frame. Simulations based on the second method proceed much more quickly than simulations based on the first. An integral of equations of motion governing the behavior of a spacecraft, and a sphere, which is part of the damper is presented. The integral can be used to test the results of numerical integrations performed in connection with the first and second approaches.

Roithmayr, Carlos M.↗
NASA NTRS1992

Digital active material processing platform effort (DAMPER), SBIR phase 2

Applied Technology Associates, Inc., (ATA) has demonstrated that inertial actuation can be employed effectively in digital, active vibration isolation systems. Inertial actuation involves the use of momentum exchange to produce corrective forces which act directly on the payload being actively isolated. In a typical active vibration isolation system, accelerometers are used to measure the inertial motion of the payload. The signals from the accelerometers are then used to calculate the corrective forces required to counteract, or 'cancel out' the payload motion. Active vibration isolation is common technology, but the use of inertial actuation in such systems is novel, and is the focus of the DAMPER project. A May 1991 report was completed which documented the successful demonstration of inertial actuation, employed in the control of vibration in a single axis. In the 1 degree-of-freedom (1DOF) experiment a set of air bearing rails was used to suspend the payload, simulating a microgravity environment in a single horizontal axis. Digital Signal Processor (DSP) technology was used to calculate in real time, the control law between the accelerometer signals and the inertial actuators. The data obtained from this experiment verified that as much as 20 dB of rejection could be realized by this type of system. A discussion is included of recent tests performed in which vibrations were actively controlled in three axes simultaneously. In the three degree-of-freedom (3DOF) system, the air bearings were designed in such a way that the payload is free to rotate about the azimuth axis, as well as translate in the two horizontal directions. The actuator developed for the DAMPER project has applications beyond payload isolation, including structural damping and source vibration isolation. This report includes a brief discussion of these applications, as well as a commercialization plan for the actuator.

Blackburn, John↗
NASA NTRS1994

Squeeze film dampers with oil hole feed

To improve the damping capability of squeeze film dampers, oil hole feed rather than circumferential groove feed is a practical proposition. However, circular orbit response can no longer be assumed, significantly complicating the design analysis. This paper details a feasible transient solution procedure for such dampers, with particular emphasis on the additional difficulties due to the introduction of oil holes. It is shown how a cosine power series solution may be utilized to evaluate the oil hole pressure contributions, enabling appropriate tabular data to be compiled. The solution procedure is shown to be applicable even in the presence of flow restrictors, albeit at the expense of introducing an iteration at each time step. Though not of primary interest, the procedure is also applicable to dynamically loaded journal bearings with oil hole feed.

Chen, P. Y. P.↗
NASA NTRS1996

Analysis of Two-Phase Flow in Damper Seals for Cryogenic Turbopumps

Cryogenic damper seals operating close to the liquid-vapor region (near the critical point or slightly su-cooled) are likely to present two-phase flow conditions. Under single phase flow conditions the mechanical energy conveyed to the fluid increases its temperature and causes a phase change when the fluid temperature reaches the saturation value. A bulk-flow analysis for the prediction of the dynamic force response of damper seals operating under two-phase conditions is presented as: all-liquid, liquid-vapor, and all-vapor, i.e. a 'continuous vaporization' model. The two phase region is considered as a homogeneous saturated mixture in thermodynamic equilibrium. Th flow in each region is described by continuity, momentum and energy transport equations. The interdependency of fluid temperatures and pressure in the two-phase region (saturated mixture) does not allow the use of an energy equation in terms of fluid temperature. Instead, the energy transport is expressed in terms of fluid enthalpy. Temperature in the single phase regions, or mixture composition in the two phase region are determined based on the fluid enthalpy. The flow is also regarded as adiabatic since the large axial velocities typical of the seal application determine small levels of heat conduction to the walls as compared to the heat carried by fluid advection. Static and dynamic force characteristics for the seal are obtained from a perturbation analysis of the governing equations. The solution expressed in terms of zeroth and first order fields provide the static (leakage, torque, velocity, pressure, temperature, and mixture composition fields) and dynamic (rotordynamic force coefficients) seal parameters. Theoretical predictions show good agreement with experimental leakage pressure profiles, available from a Nitrogen at cryogenic temperatures. Force coefficient predictions for two phase flow conditions show significant fluid compressibility effects, particularly for mixtures with low mass content of vapor. Under these conditions, an increase on direct stiffness and reduction of whirl frequency ratio are shown to occur. Prediction of such important effects will motivate experimental studies as well as a more judicious selection of the operating conditions for seals used in cryogenic turbomachinery.

Arauz, Grigory L.↗
NASA NTRS2000

An Unsteady Long Bearing Squeeze Film Damper Model: Circular Centered Orbits - Part 1

This paper, the first of a two-part series, presents results of an unsteady rotordynamic analysis of a long-bearing squeeze film damper executing circular centered orbits using a fluid circuit approach. A series of nodes and branches represent the geometry of the flow circuit. The mass and momentum conservation equations are solved to predict the pressure distribution in the squeeze film. The motion of the bearing is simulated by the variation of geometry within the flow path. The modeling methodology is benchmarked against published experimental long-bearing squeeze film damper test results. The model provides good agreement with the experimental damping coefficient.

Schallhorn, P. A.↗
NASA NTRS2004

Improved Nutation Damper for a Spin-Stabilized Spacecraft

A document proposes an improved liquid- ring nutation damper for a spin-stabilized spacecraft. The improvement addresses the problem of accommodating thermal expansion of the damping liquid. Heretofore, the problem has been solved by either (1) filling the ring completely with liquid and accommodating expansion by attaching a bellows or (2) partially filling the ring and accepting the formation of bubbles. The disadvantage of (1) is that a bellows is expensive and may not be reliable; the disadvantage of (2) is that bubbles can cause fluid lockup and consequent loss of damping. In the improved damper, the ring would be nearly completely filled with liquid, and expansion would be accommodated, but not by a bellows. Instead, an escape tube would be attached to the ring. The escape tube would be positioned and oriented so that the artificial gravitation and the associated buoyant force generated by the spin of the spacecraft would cause the bubbles to migrate toward the tip of the tube. In addition, when the spacecraft was on the launch pad, the escape tube would be at the top of the ring, so that bubbles would rise into the tube.

Woodard, Mark A.↗
NASA NTRS2014

Compact Vibration Damper

A vibration damper includes a rigid base with a mass coupled thereto for linear movement thereon. Springs coupled to the mass compress in response to the linear movement along either of two opposing directions. A converter coupled to the mass converts the linear movement to a corresponding rotational movement. A rotary damper coupled to the converter damps the rotational movement.

Ivanco, Thomas G.↗