SEARCH · Search NASA

Results for “DOWNSTREAM FLOW”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

All sources NASA NTRS DOE OSTI

DOE OSTI2026

Slow Wake Recovery and Low Turbulence Behind Wind Farms Parameterized in Mesoscale Simulations

Numerical weather prediction (NWP) and climate models equipped with wind-farm parameterizations (WFPs) can simulate cluster wake effects affecting downstream wind farms in both onshore and offshore environments. This study evaluates wake recovery behind a wind farm represented by the NWP-WFP approach in the Weather Research and Forecasting (WRF) model using either the Fitch et al. (2012) or Ma et al. (2022a, b) WFPs. Results are benchmarked against large-eddy simulations (LES) of an idealized offshore wind farm with aligned and staggered layouts under neutral atmospheric stability. Near-farm wake recovery is underestimated in NWP-WFP simulations due to its representation on a coarse mesoscale grid. This limitation leads to slow wake recovery through two interconnected mechanisms: (i) spatial gradients in the wind velocity field are weaker compared to LES and (ii) turbulence kinetic energy (TKE) remains low not because of excessive dissipation but due to insufficient shear production caused by these weakened gradients. For the scenario considered here, a wind-speed bias develops in the near-farm wake and persists into the far wake. Differences between the NWP-WFP simulations and LES emerge within a short distance downstream of the farm exit, where the mesoscale simulations recover too slowly. This reduced recovery contributes approximately 0.15-0.50 m s-1 to the near-farm wind-speed bias. The bias established in this region is not subsequently compensated for downstream but instead propagates into the far wake, where wind-speed differences of approximately 0.4-0.6 m s-1 remain up to 50 km downstream. Higher-resolution mesoscale simulations partially reduce this bias. Increasing turbine-added TKE or including subgrid wake effects provides additional improvement, but neither fully addresses the underlying cause. The slow wake recovery is not caused by limitations of the WFPs themselves, as it also occurs outside their region of influence, and adding subgrid wake effects does not significantly impact recovery. Rather, the slow wake recovery is a consequence of mesoscale flow representation. This behavior is not limited to regions downstream of the wind farm but is less visible within the farm, where wake recovery occurs simultaneously with turbine-induced momentum extraction. These results highlight the need for improved representations of wake recovery both within and downstream of wind farms. While enhanced subgrid modeling, shear-driven TKE production, and refined WFP formulations may improve intra-farm dynamics, accurately capturing near-farm wake recovery downstream remains challenging, as WFPs do not act in this region.

17 WIND ENERGY↗

DOE OSTI2020

Slag Management of Carbon Feedstock Used in Gasification FY17 TCF between Eastman Chemical and NETL (Final Report)

NETL, in collaboration with Eastman Chemical Corp (Kingsport, TN), targeted the joint evaluation and refinement of a slag management program developed by NETL (NETL IP, patent applied for) to control gasifier slag properties formed from ash in individual or combinations of different coal-based carbon feedstock materials and specific slag modifiers used in gasification. Slag forms from mineral or organic-metallic impurities in the carbon feedstock that melt at the high temperatures of gasification, coalescing to form a liquid (slag) that must flow from the gasifier. Slag additives, also known as slag modifiers, are often added to the carbon feedstock to modify the ash chemistry and achieve desired slag flow properties at target temperatures used in gasification. If slag does not flow from a gasifier, its buildup within the gasification chamber will cause either gasifier shutdown to physically remove the slag (consuming time and damaging the protective refractory lining), or the gasification temperature must be increased to lower slag viscosity so it can flow from the gasifier, leading to greater refractory wear/corrosion, along with increased fouling and downstream component wear. Because of these issues, gasification is typically targeted at the lowest temperature possible where slag will flow in a controlled manner (a temperature range called T100 for the lowest temperature, with T250 being the highest temperature where the slag has achieved the desired fluidity). That temperature range also needs to yield a desired syngas composition, highlighting the importance of knowing and being able to control carbon feedstock slag viscosity and the temperature of thermal breakdown of the carbon feedstock. Slag viscosity varies with changes in the gasification chamber temperature, oxygen partial pressure, and slag chemistry. The slag model work with Eastman Chemical targeted predicting and controlling molten coal ash slag behavior at specific gasification conditions. The final goal of the refined model was to develop/refine the NETL slag model so a gasifier operator would be able to predict slag behavior prior to purchasing or using a carbon feedstock and control slag properties once a carbon feedstock is being gasified, allowing a gasifier user to determine what mineral additives or blends of different carbon materials would be needed to achieve desired slag properties at targeted gasification conditions. For a given carbon feedstock and desired gasification condition, the actual gasification cost and slag behavior would be able to be predicted using the slag management program in advance of purchasing or using the carbon feedstock – allowing accurate control of slag ash behavior in real time. As part of the TCF project work with Eastman Chemical, the viscosity of several ash compositions of interest to them would be measured and used to populate the slag model, along with a large database of historical slag temperature, chemistry, and viscosity information they possess – information that would in-crease the predictive accuracy of the slag management model with slag ash chemistry of interest to them. As part of the model evaluation and refinement, the predictive model and its database will be installed on computers at Eastman Chemical and used to manage slag properties in a gasifier during real-time operation of their gasifier. In summary, success of the slag management program at Eastman Chemical would support its use by other gasifier operators to manage slag chemistry and properties over other desired gasification temperature ranges, allowing greater process control and efficiency of their carbon feedstock conversion during gasification.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2022

Influence of sequential stimulation practices on geochemical alteration of shale

Water-based hydraulic fracturing fluids (HFFs) can chemically interact with formation shale, resulting in altered porosity and permeability of the host rock. Experimental investigations of spatial and temporal shale-HFF interactions are helpful in interpreting chemical compositions of the injectate, as well as predicting alteration of hydraulic properties in the reservoir due to mineral dissolution and precipitation. Most bench-top experiments designed to study shale-HFF chemical interactions, either using batch reactors or flow-through setups, are carried out assuming that the acid spearhead has already become mixed with neutral HFFs. During operations, however, HFFs are typically injected according to a sequenced pumping schedule, starting with a concentrated acid spearhead, followed by multiple additions of near-neutral pH HFFs containing chemical amendments and proppant. In this study, we use geochemical modeling to consider whether this pre-mixed experimental protocol provides results directly comparable to a sequential discrete fluid-shale interaction protocol. Our results show that for the batch system, the transient evolution in major ion concentrations is faster with the sequential procedure. After 2 h of reaction time, the two protocols converge to the same aqueous concentrations. In a flow-through geometry, the pre-mixed model predicts extensive chemical alteration close to the injection point but negligible alteration downstream. In contrast, the sequential model predicts mineral reactions over hundreds of meters along the flow path. The extent of shale alteration in the sequential model at a given location depends on shale mineralogy and where the acid spearhead resides during the shut-in period. The predictive model developed in this study can help experimentalists to design bench-top tests and operators to better translate the results of laboratory experiments into practical applications.

Li, Qingyun↗

DOE OSTI2025

Separating Sensible and Latent Cooling with Electrically Charged Rotating Vortexes and Vapor Capturing Air Handler Technology

The dehumidification of air is a highly energy-intensive process, typically requiring vapor compression systems to cool the air below its dew point temperature. This project investigated air dehumidification achieved by electrostatic and dielectrophoresis forces in electrosprays and centrifugal principles in cyclone separators. As a practical implementation of these processes, Electrospray Vortical Flow eXchanger (EVFX) prototypes were designed, fabricated, and tested. Electrosprays were employed to energize water droplets, which then captured water vapor via dielectrophoresis. A cyclone separator was positioned downstream of the electrosprays. This combination increased the dehumidification efficiency and controlled the flow of the water vapor condensate removed from the air.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2022

Shock interacting with a random array of stationary particles underwater

Accurately predicting the force experienced by particles within a random bed during shock traversal is a challenging problem. In this paper, particle-resolved inviscid simulations of shock propagation over randomly distributed beds are performed, with the goal of quantifying the force on individual particles. Water was considered the continuum material, and then results were compared with previous research completed in air and the differences resulting from these different mediums were examined. Simulations were conducted for four different combinations of incident Mach number and bed volume fraction with the particles remaining stationary. Additionally, time-resolved streamwise and transverse force coefficients were calculated for each particle in the bed. It was observed that while the average force coefficient was similar to that of an isolated particle, the force on individual particles was substantially different. An important observation was that the inviscid drag force on some particles remained consistently positive, but others consistently negative even long after the passage of the shock. This persistent force on the particle was attributed to the potential flow fields that result from neighbors' specific locations upstream and downstream. Similar behavior was observed in the transverse force, with particles experiencing sustained force in the same lateral direction. These persistent forces are inviscid quasisteady contributions which with the viscous counterpart will play an essential role in the particle's long-term dispersion if allowed to move in response to the force.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

DOE OSTI2021

Evaluation of Juvenile Salmon Passage and Survival Through a Fish Weir and Other Routes at Foster Dam, Oregon, USA

Downstream passage for juvenile Chinook salmon (Oncorhynchus tshawytscha) and steelhead (O. mykiss) through the fish weir at Foster Dam, Oregon, was evaluated to assess the weir’s efficacy as a long-term passage solution. Radio telemetry was used to estimate survival, passage, and effectiveness for the fish weir, spillway, and turbines. Survival of Chinook salmon through the fish weir varied by season and reservoir elevation (66–87%), passage proportions were low (8–20%), and fish weir effectiveness was low to moderate (0.5–2.0). Steelhead survival was lower (57–77%) but passed the fish weir in higher proportions (77%) and weir effectiveness was consistently high (3.0–5.5). Our results indicate the existing fish weir will not be a suitable long-term passage solution for all species. However, because of the high passage proportions and effectiveness observed for steelhead, further development of the surface flow concept appears to be promising for safely passing downstream-migrating fishes.

Hughes, James S.↗

DOE OSTI2022

Numerical study of multi-component flow and mixing in a scaled fission product venting system

Numerical simulation of isothermal multi-component gas flow was conducted to study fluid flow and mixing in a scaled low-pressure, low-temperature test facility for the fission product venting system (FPVS) of a gas cooled fast reactor (GFR). The geometry of FPVS test facility was an open loop including gradual expansion coupling and two 90°pipe elbows. First, the validation of large eddy simulation (LES) wall-adapting local eddy-viscosity (WALE) turbulent model was performed for transitional flow in a circular pipe with gradual expansion. The reactingFOAM solver in OpenFOAM v8 was employed. By introducing appropriate turbulence disturbance at the flow inlet, such as turbulence intensity, the numerical results showed good agreement in (1) the velocity profile downstream of the pipe expansion measured by particle image velocimetry (PIV) in this study, and (2) the reattachment length reported in the literature. Using this validated model, the numerical simulation of flow and component mixing was performed for the FPVS with an inlet flowrate corresponding to a Reynolds number of 2,400 to investigate the flow behavior and component mixing. Standard deviation of the mass fraction of component, referred to as absolute mixing index (AMI), was calculated to quantify the mixing of components, showing that the component mixing length determined by AMI is related to the reattachment length downstream of the expansion. Additionally, this study was able to identify the best location in the FPVS test facility to measure the velocity and concentration profies where multicomponent flow is well mixed.

15 GEOTHERMAL ENERGY↗

DOE OSTI2022

Temperature measurements in heavily-sooting ethylene/air flames using synchrotron x-ray fluorescence of krypton

High-fidelity temperature field measurements have been made for several heavily-sooting ethylene/air flames that have historically been challenging environments for conventional optical diagnostics. These challenges have largely been overcome here, in this study, by conducting x-ray fluorescence (XRF) measurements of a Kr fluorescent agent in the hard x-ray regime (15 keV). The current methodology presents a more economical diagnostic than a previously reported implementation of the Kr-XRF method, by limiting seeding of the expensive fluorescent agent to only the fuel stream flows. Detailed reacting flow simulations have been used to interpret experimental signals by tracking the mole fraction of the fluorescent agent in the flow field. Simulated Kr densities are in excellent agreement with measurements throughout the flow field. Temperature measurements of the flow field also agree well with simulations and recent literature studies. However, uncertainties in the measurements become increasingly large downstream of the burner surface as the krypton fraction drops due to mixing of the fuel and co-flow streams. Additionally, we demonstrate that soot particles in the heavily sooting flames studied do not impede the Kr-XRF measurements.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Biomass Feedstock Flow Modeling at Exascale

Variable biomass feedstock handling in hoppers and screw conveyors can cause upstream failures and disrupt downstream conversion operations. Understanding how particle size, shape, and moisture content affect feedstock flowability is important for efficient biorefinery operation. We present the use of our open-source discrete element method (DEM) solver for predicting flows in large scale hoppers and assess its performance on state-of-the-art high performance computing platforms that use heterogenous computing architectures.

bioenergy↗

DOE OSTI2024

Large-eddy simulations of turbulent wake flows behind helical- and straight-bladed vertical axis wind turbines rotating at low tip speed ratios

Turbulent wake flows behind helical- and straight-bladed vertical axis wind turbines (VAWTs) rotating at low tip speed ratios (TSRs) are studied numerically. The turbulent flows are simulated using the large-eddy simulation (LES) model, and the rotating turbine blades are modeled using the actuator line method. The helical VAWT has identical key parameters as the straight VAWT except for the 135° helical twist of the blades over the 0.3m vertical span. A set of LES runs are performed for two TSRs, 0.6 and 0.4, and the results are reported and analyzed. At these low TSRs, the wake behind the straight-bladed VAWT exhibits two-dimensional dominant flow motions (in the horizontal plane perpendicular to the straight blades) in the near-wake region that cause considerable spanwise expansion of the wake as it extends downstream. In contrast, the helical-bladed VAWT generates highly three-dimensional (3D) wake flow structures and upward/downward mean flow motions within the wake that cause the wake to expand mainly in the vertical direction. Turbulence statistical analyses also show that the 3D wake flow features induced by the helical blades accelerate the wake transition to turbulence and enhance the small-scale turbulent dissipation (as shown by the subgrid-scale turbulent dissipation in the LES), which leads to a more rapid decay of the wake turbulence intensity than that in the straight-bladed VAWT case at the same TSR. Finally, compared with the straight-bladed VAWT, the helical-bladed VAWT also exhibits much smaller temporal variations for the torque and power coefficients during the rotation cycle, which can be beneficial for wind power generation.

17 WIND ENERGY↗

DOE OSTI2023

Testing of Microchannels and Lab-Grown Stress Corrosion Cracks for Quantification of Aerosol Transmission

The formation of a stress corrosion crack (SCC) in the canister wall of a dry cask storage system (DCSS) has been identified as a potential issue for the long-term storage of spent nuclear fuel. The presence of an SCC in a storage system could represent a through-wall flow path from the canister interior to the environment. Modern, vertical DCSSs are of particular interest due to the commercial practice of using higher backfill pressures in the canister, up to approximately 800 kPa, compared to their horizontal counterparts. This pressure differential offers a relatively high driving potential for blowdown of any particulates that might be present in the canister. In this study, the rates of gas flow and aerosol transmission of a spent fuel surrogate through an engineered microchannel with dimensions representative of an SCC were evaluated experimentally using coupled mass flow and aerosol analyzers. The microchannel was formed by mating two gage blocks with a linearly tapering slot orifice nominally 13 μm (0.005 in.) tall on the upstream side and 25 μm (0.0010 in.) tall on the downstream side. The orifice is 12.7 mm (0.500 in.) wide by 8.86 mm (0.349 in.) long (flow length). Surrogate aerosols of cerium oxide, CeO 2 , were seeded and mixed with either helium or air inside a pressurized tank. The aerosol characteristics were measured immediately upstream and downstream of the simulated SCC at elevated and ambient pressures, respectively. These data sets are intended to add to previous testing that characterized SCCs under well-controlled boundary conditions through the inclusion of testing improvements that establish initial conditions in a more consistent way. While the engineered microchannel has dimensions similar to actual SCCs, it does not reproduce the tortuous path the aerosol laden flow would have to traverse for eventual transmission. SCCs can be rapidly grown in a laboratory setting given the right conditions, and initial characterization and clean-flow testing has begun on lab grown crack samples provided to Sandia National Laboratories (SNL). Many such samples are required to produce statistically relevant transmission results, and SNL is developing a procedure to produce samples in welded steel plates. These ongoing testing efforts are focused on understanding the evolution in both size and quantity of a hypothetical release of aerosolized spent fuel particles from failed fuel to the canister interior and ultimately through an SCC.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2024

Foundation Models for the Electric Power Grid

Foundation models (FMs) currently dominate news headlines. They employ advanced deep learning architectures to extract structural information autonomously from vast datasets through self-supervision. The resulting rich representations of complex systems and dynamics can be applied to many downstream applications. Therefore, advances in FMs can find uses in electric power grids, challenged by the energy transition and climate change. This paper calls for the development of FMs for electric grids. We highlight their strengths and weaknesses amidst the challenges of a changing grid. It is argued that FMs learning from diverse grid data and topologies, which we call grid foundation models (GridFMs), could unlock transformative capabilities, pioneering a new approach to leveraging AI to redefine how we manage complexity and uncertainty in the electric grid. Finally, we discuss a practical implementation pathway and road map of a GridFM-v0, a first GridFM for power flow applications based on graph neural networks, and explore how various downstream use cases will benefit from this model and future GridFMs.

AI-based power flow simulation↗

DOE OSTI2025

Deconvoluting sources of variability in aerosol jet printing using light scattering measurements

Aerosol jet printing (AJP) is a digital additive manufacturing technique for hybrid and conformal electronics, where its contactless deposition readily enables patterning over 3D surface topography. However, the complexity of aerosol transport physics makes deposition rate sensitive to process variability, hindering widespread industry adoption. Light scattering measurements have recently been demonstrated as a capable tool for measuring deposition rate in real time, enabling closed-loop control and in-situ qualification frameworks. These inline optical measurements present further opportunity as a diagnostic tool to understand the effects of secondary process parameters affecting vapor–liquid equilibrium and heat and mass transport during deposition. Downstream of the optical measurement cell, changing the sheath gas flow rate, increasing temperature via an inline heater, and adding solvent vapor via a sheath gas bubbler were observed to alter drying physics during sheath-collimation, and thereby impaction efficiency. Further upstream, the introduction of solvent vapor via a carrier gas bubbler and liquid build-up in the printhead were seen to affect the quantitative relationship between the light scattering data and the true deposition rate. Using this information, tightened controls of meaningful secondary parameters were implemented to improve the batch-to-batch consistency for printing a dielectric ink. In addition to advancing AJP process reliability for production, this work demonstrates the capability of inline optical measurements to provide insight into process physics and deconvolute competing mechanisms that underly variability.

additive manufacturing↗

DOE OSTI2020

Etching of Si 3 N 4 induced by electron beam plasma from hollow cathode plasma in a downstream reactive environment

An etching system based on the interaction of electrons extracted from a direct current (DC) hollow-cathode (HC) Ar plasma and injected towards a Si3N4 covered silicon substrate located in the downstream reactive environment created by an additional remote CF 4 /O 2 plasma source was developed and evaluated. By controlling the properties of the injected beam electrons, this approach allows to deliver energy to a surface functionalized by exposure to reactive species, and initiate surface etching. The energy of the primary beam electrons is controlled by the acceleration voltage relative to the HC discharge. Ar atoms flow from the high-pressure HC discharge into the low pressure downstream reactive environment in the process chamber. For an acceleration voltage greater than the ionization potential of Ar and/or process gas species, the energetic primary beam electrons produce a secondary plasma in the process chamber, and can also cause additional dissociation. We have characterized the properties of the secondary plasma and also surface etching of Si 3 N 4 as a function of process parameters, including acceleration voltage (0-80 V), discharge current of the HC discharge (1-2 A), pressure (3.5-20 mTorr), source to substrate distance (1.5 to 5 cm), and feed gas composition (20% and 80% O2 in CF 4 /O 2 ). The electron energy probability function (EEPF) measured with a Langmuir probe about 2.5 cm below the extraction ring suggests several major groups of electrons for this situation, including high energy primary beam electrons with an energy that varies as the acceleration voltage is changed and low energy electrons produced by beam electron-induced ionization of the Ar gas in the process chamber. When a remote CF 4 /O 2 plasma is additionally coupled to the process chamber, Si 3 N 4 surfaces can be functionalized, and by varying the energy of the beam electrons, Si 3 N 4 etching can be induced by electron-neutral synergy effect with plasma-surface interaction. For conditions without beam electron injection, the remote plasma etching rate (ER) of Si 3 N 4 depends strongly on the O 2 concentration in the CF 4 /O 2 processing gas mixture and can be suppressed for O 2 -rich process conditions by the formation of a SiONF passivation layer on the Si 3 N 4 surface. The combination of the HC electron beam source with the remote plasma source (HCEB-RP) makes it possible to induce Si 3 N 4 etching for O 2 -rich remote plasma conditions where remote plasma by itself produces negligible Si 3 N 4 etching. The electron enhanced etching of Si 3 N 4 depends strongly on O 2 /CF 4 mixing ratio reflecting changing arrival rates of O and F species at the surface. Optical emission spectroscopy was used to estimate the ratio of gas phase F and O densities and found to be controlled by the gas mixing ratio and independent of HC EB operating conditions. At this time the detailed sequence of events operative in the etching mechanism is unclear. While the increase of the electron energy is ultimately responsible for initiating surface etching, at present we cannot rule out a role of ions from the simultaneously produced secondary plasma in plasma surface interaction mechanisms.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Continued Investigations of Respirable Release Fractions for Stress Corrosion Crack-Like Geometries

The formation of a stress corrosion crack (SCC) in the canister wall of a dry cask storage system (DCSS) has been identified as a potential issue for the long-term storage of spent nuclear fuel. The presence of an SCC in a storage system could represent a through-wall flow path from the canister interior to the environment. Modern, vertical DCSSs are of particular interest due to the commercial practice of using relatively high backfill pressures (up to approximately 800 kPa) in the canister to enhance internal natural convection. This pressure differential offers a comparatively high driving potential for blowdown of any particulates that might be present in the canister. In this study, the rates of gas flow and aerosol transmission of a spent fuel surrogate through an engineered microchannel with dimensions representative of an SCC were evaluated experimentally using coupled mass flow and aerosol analyzers. The microchannel was formed by mating two gage blocks with a linearly tapering slot orifice nominally 13 μm (0.005 in.) tall on the upstream side and 25 μm (0.0010 in.) tall on the downstream side. The orifice is 12.7 mm (0.500 in.) wide by 8.89 mm (0.350 in.) long (flow length). Surrogate aerosols of cerium oxide, CeO 2 , were seeded and mixed with either helium or air inside a pressurized tank. The aerosol characteristics were measured immediately upstream and downstream of the simulated SCC at elevated and ambient pressures, respectively. These data sets are intended to demonstrate a new capability to characterize SCCs under well-controlled boundary conditions. Modeling efforts were also initiated that evaluate the depletion of aerosols in a commercial dry storage canister. These preliminary modeling and ongoing testing efforts are focused on understanding the evolution in both size and quantity of a hypothetical release of aerosolized spent fuel particles from failed fuel to the canister interior and ultimately through an SCC.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2022

Quantification of Aerosol Transmission through Stress Corrosion Crack-Like Geometries

The formation of a stress corrosion crack (SCC) in the canister wall of a dry cask storage system (DCSS) has been identified as a potential issue for the long-term storage of spent nuclear fuel. The presence of an SCC in a storage system could represent a through-wall flow path from the canister interior to the environment. Modern, vertical DCSSs are of particular interest due to the commercial practice of using more significant backfill pressures in the canister, up to approximately 800 kPa. This pressure differential offers a relatively high driving potential for blowdown of any particulates that might be present in the canister. In this study, the rates of gas flow and aerosol transmission of a spent fuel surrogate through an engineered microchannel with dimensions representative of an SCC were evaluated experimentally using coupled mass flow and aerosol analyzers. The microchannel was formed by mating two gage blocks with a linearly tapering slot orifice nominally 13 μm (0.005 in.) tall on the upstream side and 25 μm (0.0010 in.) tall on the downstream side. The orifice is 12.7 mm (0.500 in.) wide by 8.86 mm (0.349 in.) long (flow length). Surrogate aerosols of cerium oxide, CeO 2 , were seeded and mixed with either helium or air inside a pressurized tank. The aerosol characteristics were measured immediately upstream and downstream of the simulated SCC at elevated and ambient pressures, respectively. These data sets are intended to add to previous testing that characterized SCCs under well-controlled boundary conditions through the inclusion of testing improvements that establish initial conditions in a more consistent way. These ongoing testing efforts are focused on understanding the evolution in both size and quantity of a hypothetical release of aerosolized spent fuel particles from failed fuel to the canister interior and ultimately through an SCC.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2025

Modeling the microplastic distribution along the Delaware River Estuary: Accumulation patterns and hydrodynamic influences

Microplastic pollution is an escalating environmental concern, particularly in densely populated estuary regions, where it poses significant threats to aquatic life and human health. The dispersion patterns of microplastic particles along estuaries are influenced and complicated by multiple environmental factors such as river flow, tidal mixing, salt intrusion, and estuarine circulation. This study examines the accumulation and dispersion patterns by modeling three typical classes of microplastics in the Delaware River Estuary: synthetic fibers, sinking plastic films, and rising plastic pellets. Our findings reveal specific areas with high microplastic accumulation for each type. Notably, the upper estuary regions exhibit significant retention of rising microplastics, associated with a region with reduced along-thalweg velocities downstream of Trenton, NJ and upstream of Philadelphia, PA. Conversely, synthetic fibers and sinking plastic films accumulate in the flow convergence zone near the bottom salinity front, typically downstream of Philadelphia. All of the microplastic accumulation hot spot locations are controlled by the balance of river discharge and salinity intrusions. During the dry season, microplastic accumulation hot spots shift upstream in the estuary, whereas in the wet season, the strong river discharge pushes them downstream. Furthermore, on the other hand, tidal mixing, settling, and resuspension processes strongly impact the spreading of microplastics along the river.

Delaware River Estuary↗

DOE OSTI2025

Numerical analysis of air dehumidification through electrospray-enhanced vortical flow cyclone separator

The dehumidification of air is a highly energy-intensive process, typically requiring vapor compression systems to cool the air significantly below its dew point temperature. Here, this study numerically investigates air dehumidification achieved by electrostatic and dielectrophoresis forces in a converging duct and centrifugal principles in cyclone separators. An electrospray was employed to energize water droplets, which then captured water vapor via dielectrophoresis. A novelty of the present study is the inclusion of a cyclone separator positioned downstream of the electrospray. This combination increased the dehumidification efficiency and controlled the flow of the condensate. By integrating electrospray technology and applying an electric field, this study examines the impact of particle separation efficiency, pressure drops, and cyclone performance on air dehumidification. The control parameters for air dehumidification were investigated. Three cyclones were modelled for airflow rates of 5 cubic feet per minute [cfm] (0.0024 m 3 /s), 38 cfm (0.0179 m 3 /s), and 200 cfm (0.094 m 3 /s). The results indicated air dehumidification was up to 5.7 % under environmental conditions, similar to those used to validate the CFD model. The degree of air dehumidification was primarily influenced by the electric charge acquired by the water droplets, their flight trajectory, and the vorticity intensity within the cyclone. Air dehumidification could increase by up to 13 % by increasing the number of droplets injected into the air stream, the flight time, and the electrical charge. The breakdown electric field strength threshold near the electrospray was a limiting factor for further enhancing dehumidification performance. This study examines the optimization of an electro-assisted dehumidification system that includes cyclone-based droplet separation through numerical analysis. The results provide insights into the design of energy-efficient air treatment technologies.

42 ENGINEERING↗