Search NASA⌕ Search

SEARCH · Search NASA

Results for “Diesel combustion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Effect of CO on alcohol oxidation over commercial oxidation catalysts for control of emissions from lean-burn engines

For commercialization, alcohol-based net-zero carbon fuels in diesel-driven internal combustion engines must meet emissions standards set by the U.S. Environmental Protection Agency. Here, a series of aged commercial oxidation catalysts, Pt diesel oxidation catalyst (DOC), Pd+Pt DOC, and Pt oxidation catalyst (Pt OC), were studied using an automated flow reactor and in situ DRIFTS techniques to investigate the impact of CO on alcohol oxidation. Surface formate and acetate intermediates were formed due to partial oxidation of methanol and ethanol, respectively. Sequential introduction of alcohol and CO experiments using in situ DRIFTS on all three catalysts showed that CO inhibited low temperature methanol oxidation. Mutual inhibition effects between CO and ethanol were observed during co-oxidation. Acetate species shifted CO oxidation to higher temperatures on Pt DOC and Pt OC, whereas CO pre-exposure inhibited acetate formation. CO oxidation occurred at lower temperatures during ethanol and CO co-oxidation on Pd+Pt DOC.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2023

Experimental Characterization of Hydrocarbons and Nitrogen Oxides Production in a Heavy-Duty Diesel–Natural Gas Reactivity-Controlled Compression Ignition Engine

Reactivity-Controlled Compression Ignition (RCCI) combustion is considered one of the most promising Low-Temperature Combustion (LTC) concepts aimed at reducing greenhouse gases for the transportation and power generation sectors. Due to the spontaneous combustion of a lean, nearly homogeneous mixture of air and low-reactivity fuel (LRF), ignited through the direct injection of a small quantity of high-reactivity fuel (HRF), RCCI (dual-fuel) shows higher efficiency and lower pollutants compared to conventional diesel combustion (CDC) if run at very advanced injection timing. Even though a HRF is used, the use of advanced injection timing leads to high ignition delays, compared to CDC, and generates high cycle-to-cycle variability, limited operating range, and high pressure rise rates at high loads. This work presents an experimental analysis performed on a heavy-duty single-cylinder compression ignited engine in dual-fuel diesel–natural gas mode. The objective of the present work is to investigate and highlight the correlations between combustion behavior and pollutant emissions, especially unburned hydrocarbons (HC) and oxides of nitrogen (NOx). Based on the analysis of crank-resolved pollutants measurements performed through fast FID and fast NOx systems under different engine operating conditions, two correlations were found demonstrating a good accordance between pollutant production and combustion behavior: Net Cyclic Hydrocarbon emission—cyclic IMEP variations (R 2 = 0.86), and Cyclic NOx—maximum value of the Rate of Heat Released (R 2 = 0.82).

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

Quantifying Impacts of Renewable Electricity Deployment on Air Quality and Human Health in Southeast Asia Based on Aims III Scenarios

Exposure to outdoor air pollution is the largest environmental risk factor for death and disease worldwide, associated with millions of cases of excess deaths (mortality) each year. Although there are many pollutants in the air that affect our health, the most important class of pollutants is fine particulate matter, PM 2.5 , which are airborne particles of diameter ≤2.5 micrometers (µm). These particles are small enough to deposit deep in the respiratory system where they can then enter the bloodstream, traveling and causing damage to other bodily systems. Exposure to outdoor (ambient) PM 2.5 has been found to be the most important environmental risk factor for mortality in Southeast Asia, associated with 130,000 - 320,000 excess deaths in Association of Southeast Asian Nations (ASEAN) member countries in 2019. Southeast Asia, especially its mega-cities, but also other areas, has some of the worst air quality in the world. Almost all human activity emits air pollutants. Fine particulate matter is both directly emitted and formed in the atmosphere through chemical reactions, the latter of which requires modeling to predict. Power generation is one of the major sources of air pollutants that lead to elevated concentrations of fine particulate matter, including in Southeast Asia. Fossil fuel combustion for power generation, especially coal but also diesel, is the main source of air pollutant emissions from power generation. While natural gas burns cleaner than coal or diesel, in the quantities combusted for power generation in Southeast Asia, it is also a significant emitter. This study augments the ASEAN Interconnection Masterplan Study III (AIMS III) by quantifying changes to air quality and human health that result from its renewable integration and transmission interconnection scenarios. Performing this analysis requires translation of the changes in projected generation from different power sector fuel sources in the AIMS III scenarios to changes in air pollutant emissions, developing what's known as an emissions inventory for each scenario and year evaluated. We then use for the first time a new global, reduced-complexity air quality model to transform the changes in emissions to changes in air pollutant concentration of the deadliest air pollutant for human health, fine particulate matter (or PM 2.5 ). The air quality model, Global InMAP, then utilizes the location of human population in ASEAN countries to calculate exposure to PM 2.5 concentration changes and translates that to estimates of excess mortality attributable to the AIMS III scenarios.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2021

A Hybrid Heavy-Duty Diesel Power System for Off-Road Applications - Concept Definition

A multi-year Power System R&D project was initiated with the objective of developing an off-road hybrid heavy-duty concept diesel engine with front end accessory drive-integrated energy storage. This off-road hybrid engine system is expected to deliver 15-20% reduction in fuel consumption over current Tier 4 Final-based diesel engines and consists of a downsized heavy-duty diesel engine containing advanced combustion technologies, capable of elevated peak cylinder pressures and thermal efficiencies, exhaust waste heat recovery via SuperTurbo™ turbocompounding, and hybrid energy recovery through both mechanical (high speed flywheel) and electrical systems. The first year of this project focused on the definition of the hybrid elements using extensive dynamic system simulation over transient work cycles, with hybrid supervisory controls development focusing on energy recovery and transient load assist, in Caterpillar’s DYNASTY™ software environment. Three key off-road applications were the focus of the hybrid concept definition with an aim of understanding the system’s modular capability for the diverse off-road heavy-duty market. Core engine performance 1D and 3D simulations isolated the efficiency contributions from the downsized engine, turbocompounding, and in-cylinder thermal barrier coatings. A fuel consumption improvement range of 14 to 24% was predicted, resulting in successful project progression to the design and experimental validation phase. Furthermore, an overview of the experimental engine and hybrid system status concludes the discussion along with the multi-year project’s next steps.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2020

Methyl propyl ether combustion

Ethers are potential diesel blendstocks that have high cetane numbers and identified cost-effective production pathways. Among ethers, methyl propyl ether (MPE) is a small enough molecule to build a good detailed model for and a large enough molecule for studying key intramolecular hydrogen migrations involved in low-temperature feedback loops for larger ethers. In this study, a model was generated for the combustion of MPE from 600-900 K and 10-20 bar using the Reaction Mechanism Generator (RMG) package. Results from rapid compression machine (RCM) experiments were used to validate the kinetic model. At low temperatures, the generated model successfully captured the dominant low-temperature feedback loops. At higher temperatures, propanal is a major combustion intermediate for PME, suggesting that aldehydes likely play a significant role in larger ethers' combustion.

09 BIOMASS FUELS↗
DOE OSTI2020

Experimental Study of the Effect of Start of Injection and Blend Ratio on Single Fuel Reformate RCCI

Abstract A new concept of single fuel reactivity-controlled compression ignition (RCCI) has been proposed through the catalytic partial oxidation (CPOX) reformation of diesel fuel. The reformed fuel mixture is then used as the low reactivity fuel and diesel itself is used as the high reactivity fuel. In this paper, two reformate mixtures from the reformation of diesel were selected for further analysis. Each reformate fuel mixture contained a significant fraction of inert gases (89% and 81%). The effects of the difference in the molar concentrations of the reformate mixtures were studied by experimenting with diesel as the direct injected fuel in RCCI over a varying start of injection timings and different blend ratios (i.e., the fraction of low and high reactivity fuels). The reformate mixture with the lower inert gas concentration had earlier combustion phasing and shorter combustion duration at any given diesel start of injection timing. The higher reactivity separation between reformate mixture and diesel, compared with gasoline and diesel, causes the combustion phasing of reformate-diesel RCCI to be more sensitive to the start of injection timing. The maximum combustion efficiency was found at a CA50 before top dead center (TDC), whereas the maximum thermal efficiency occurs at a CA50 after TDC. The range of energy-based blend ratios in which reformate-diesel RCCI is possible is between 25% and 45%, limited by ringing intensity (RI) at the low limit of blend ratios, and coefficient of variance (COV) of net indicated mean effective pressure (IMEPn) and combustion efficiency at the high limit. Intake boosting becomes necessary due to the oxygen deficiency caused by the low energy density of the reformate mixtures as it displaces intake air.

Engineering↗
DOE OSTI2022

Ethanol to diesel: a sustainable alternative for the heavy-duty transportation sector

The combustion of middle distillates (diesel and jet fuel) is responsible for the emission of more than 2 GTon of CO 2 per year worldwide. While sustainable alternatives exist for gasoline and jet fuel, we still lack sustainable alternatives for diesel. This fact is especially relevant if we consider that electrification of sectors where diesel is used is challenging. One sustainable approach for diesel production is the catalytic upgrading of ethanol. While most work in this field has focused on the dehydration/oligomerization of ethanol, this approach is limited to producing fuels that have a high degree of branching and low cetane number. Another approach is the sequential use of ethanol Guerbet coupling, leading to higher alcohols, followed by etherification, leading to large ethers which, importantly, result in a product with high cetane number. In this work, we explore the catalytic upgrading of ethanol into diesel following an approach based on the initial Guerbet coupling of ethanol followed by etherification. The results presented are a collaborative and synergic effort among process and systems engineers, experimentalist in the area of catalysis, and fuel property modelers. Here, we demonstrate experimentally the feasibility of upgrading ethanol into a diesel fuel with properties that surpass its fossil counterpart. The diesel produced has a predicted cetane number of ~70 and outstanding cold flow properties, while maintaining other properties (viscosity, density, and flash point) within expected ranges. A technoeconomic analysis performed based on a detailed biorefinery model shows that the MFSP is ~5.89$ per Gal in 2021 dollars when lignocellulosic ethanol is used, with the most relevant economic driver the cost of the ethanol feedstock. The upgrading process can be performed with a net energy gain (EROI = 1.49 > 1). An LCA analysis of greenhouse gas (GHG) emissions reveals that the use of lignocellulosic ethanol may lead to more than 50% reduction in GHG emissions compared to fossil diesel. Depending on the CO 2 emissions associated with the production of ethanol we show that in some instances the production of carbon neutral diesel fuel is possible.

09 BIOMASS FUELS↗
DOE OSTI2025

Co-optimization of fuel properties, combustion system geometry, and injection strategy for conventional diesel fuel

Here, studies have shown that fuel properties can impact an engine’s operation in several ways, including ignition delay, sooting tendency, mixture formation, and combustion temperature. In mixing-controlled compression ignition (MCCI) engines, the fuel system design and piston bowl geometry significantly affect combustion performance and emissions. Based on current information, it is difficult to draw conclusions about fuel property effects and sensitivities. The central fuel hypothesis approach used in the US Department of Energy Co-Optima program has worked well for spark ignition fuels: identifying critical fuel property ranges is sufficient to screen fuel blends that are expected to maximize efficiency and reduce pollutant emissions. However, for MCCI-relevant fuels, the information gained from past studies is not sufficient to build such a merit function or to allow for performing a similar screening of fuel blends. It is hypothesized that a co-optimization of a fuel’s physical and chemical properties, combustion system geometry, and injection strategy could leverage synergies between the effects of the fuel properties and geometries, resulting in improved performance over state-of-the-art. A machine learning–assisted unconstrained global optimization algorithm was used to explore a design space comprising 23 independent variables. The results show that physical property effects were minimal even for large variations in fuel properties, and the only interaction effect that was observed was the effect of varied fuel density parameters on fuel/air mixture formation. Nevertheless, these interactions were not sufficient in magnitude to significantly affect optimization results. Therefore, analysis of the results suggests that fuel physical properties cannot be leveraged in a co-optimization context to increase engine efficiency.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

Model predictive combustion control of a Gasoline Compression Ignition engine

Gasoline Compression Ignition is a novel combustion concept that derives its superiority from the high compression ratio of a compression ignition engine as well as the properties of gasoline fuel, such as longer ignition delay and higher volatility compared to diesel. Here, this combustion concept was experimentally tested on a 12.4L Class 8 truck engine. Based on these experimental data, prior efforts by the authors focused on the development of an engine model for a heavy-duty engine operating on a low-reactivity fuel. This engine model was leveraged within this study to investigate a combustion control strategy at different engine conditions and injection methods and was augmented to incorporate cycle-to-cycle combustion variations. State estimation is performed by means of a Kalman filter which feeds into a model predictive controller. The model predictive controller chooses control actions based on a predefined cost function under consideration of bounds reflecting physical constraints. The engine model was utilized to establish a state-space model that serves the Kalman filter and model predictive controller for estimation and prediction. A comparative study investigating control actions and engine behavior was performed with and without limiting in-cylinder peak pressure as well as combustion noise, which is of particular interest for early pilot injection strategies. In addition, the proposed control architecture was investigated at two different levels of cycle-to-cycle variations and compared to the performance of a control structure with input disturbance rejection. For increased cycle-to-cycle variations, disturbance estimation reduces state fluctuations and control effort. In general, this investigation highlights control aspects specific to a compression-ignited combustion regime with low-reactivity fuel. The control algorithm is able to maintain the desired references for brake mean effective pressure and combustion phasing while controlling peak in-cylinder pressure and combustion noise.

42 ENGINEERING↗
DOE OSTI2020

Method of exhaust cleanup from combustion processes using mixed-metal oxide based catalysts

One or more embodiments relates to a method of catalytically converting a reactant gas mixture for pollution abatement of products of hydrocarbon fuel combustion. The method provides substituted mixed-metal oxides where catalytically active metals are substituted within the crystal lattice to create an active and well dispersed metal catalyst available to convert the reactant gas mixture. Embodiments may be used with gasoline and diesel fueled internal combustion engine exhaust, although specific embodiments may differ somewhat for each.

02 PETROLEUM↗
DOE OSTI2021

Mixed-metal oxide based catalysts

One or more embodiments relates to a method of catalytically converting a reactant gas mixture for pollution abatement of products of hydrocarbon fuel combustion. The method provides substituted mixed-metal oxides where catalytically active metals are substituted within the crystal lattice to create an active and well dispersed metal catalyst available to convert the reactant gas mixture. Embodiments may be used with gasoline and diesel fueled internal combustion engine exhaust, although specific embodiments may differ somewhat for each.

Berry, David A.↗
DOE OSTI2022

Performance and Total Cost of Ownership of a Fuel Cell Hybrid Mining Truck

The main objective of this work was to investigate the potential of hydrogen and fuel cells replacing diesel and internal combustion engines in the ultraclass haul trucks deployed in the mining sector. Performance, range, durability, and cost are the main criteria considered for comparing the two fuels and engine options. Fuel cell system (FCS) performance is characterized in terms of heat rejection, efficiency, and fuel consumption for a hybrid platform equivalent to a 3500 hp diesel engine operating on a representative open pit mining duty cycle. A hybrid platform was chosen because the heat rejection, with a constrained radiator frontal area, limits the maximum fuel cell-rated power by about 50% compared to that of the diesel truck. The hybrid powertrain was 81–88% more efficient than the diesel powertrain on the truck duty cycle. A liquid hydrogen storage system is required for an equal range or time between refilling, but the packaging remains a challenge. Fuel cell and battery durability were evaluated for their performance degradation and lifetime. Achieving a fuel cell lifetime comparable to the time between major overhauls for diesel trucks necessitates the oversizing of the membrane-active area, catalyst overloading, and voltage clipping. For an equal lifetime, the battery must be oversized to control its depth of discharge and charge/discharge rates. A total cost of ownership (TCO) analysis considering the initial capital expenditures, as well as the lifetime cost of fuel, operation, and maintenance, indicates that fuel cells and hydrogen can compete with diesel. A breakeven fuel cost for TCO parity is obtained if H2 is available at USD 5.79–6.85/kg vs. diesel at USD 3.25/gal and the FCS-specific cost is USD 323/kW e relative to USD 250/kW for a diesel genset. Volume manufacturing is required for FCS cost reduction. High volume is possible through the standardization, modularity, and proliferation of class 8 long-haul truck systems across different heavy-duty applications.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2023

Model predictive control of mixing controlled compression ignition operation for low reactivity fuels

Using gasoline or other low reactivity fuels with a pilot injection or port fuel injection in a compression ignition engine has shown great potential in reducing NOx emissions while keeping high thermal efficiency compared to diesel. However, excessive combustion noise is caused by a high maximum pressure rise rate in the cylinder due to the higher fractions of premixed charge of the low-reactivity fuel. This noise can result in structural damage to engine components and as such, combustion noise limits the range of the operating parameters and makes the control of such engines challenging. In this study, a simulation environment was built up in MATLAB/Simulink leveraging a physics-based zero-dimension combustion model to capture the in-cylinder pressure time traces as well as metrics relevant to thermal efficiency and combustion noise. Here, in order to also facilitate the control of emissions, machine learning models were investigated to capture NOx emissions. A kernel-based extreme learning machine (K-ELM) performed best and had a coefficient of correlation (R-squared) of 0.998. The combustion and NOx emission models are valid for not only conventional gasoline fuel but also oxygenated alternative fuel blends at three different pilot injection strategies. In order to track key combustion metrics while keeping noise and emissions within constraints, a model predictive control (MPC) was applied for a compression ignition engine operating with a range of potential fuels and fuel injection strategies. The MPC is validated under different scenarios, including a load step change, fuel type change, and injection strategy change, with proportional–integral (PI) control as the baseline. The simulation results show that MPC reduces about 26% of ringing intensity in the transient process and 17% at the steady state for E30. Generally, MPC can optimize the overall performance through modifying the main injection timing, pilot fuel mass, and exhaust gas recirculation (EGR) fraction.

42 ENGINEERING↗
DOE OSTI2021

Oxygenated Fuel Blending Effects in a Mixing-Controlled Compression-Ignition Engine Equipped with Ducted Fuel Injection [Slides]

Continued creation of harmful emissions such as NO x and soot from compression-ignition engines utilizing mixing-controlled combustion systems (i.e., diesel engines) remains a problem and is the subject of on-going research. The inherently high efficiency, relatively low cost, and numerous other desirable attributes of such engines, coupled with a widely supported infrastructure, motivates their continued advancement. Recently, a scientifically distinct and mechanically simple technology called ducted fuel injection (DFI) has shown a robust ability to allow such engines to operate with simultaneously low engine-out soot and NO x emissions when it is employed with simulated exhaust-gas recirculation. To better understand the property ranges of sustainable, oxygenated-fuel blending stocks that will most improve engine performance, two oxygenated blendstocks were separately blended with a commercial diesel base fuel and tested within a heavy-duty diesel optical engine equipped with a four-duct DFI configuration. Conventional and crank-angle-resolved optical diagnostics were used to elucidate the effects of fuel ignition quality, oxygenate molecular structure, and overall oxygen content on engine performance.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2023

Durable Fuel Cell MEA through Immobilization of Catalyst Particle and Membrane Chemical Stabilizer

For hydrogen-based fuel cell electric vehicle to be cost competitive with the incumbent diesel-powered internal combustion engine heavy-duty vehicle, the total cost of ownership of the truck must be decreased via both capital cost and the operating cost (H 2 fuel expense) reduction. This puts the emphasis on the decrease of fuel cell stack cost via use of low platinum catalyst material usage to decrease capital cost, high H 2 fuel efficiency and high stack durability to decrease the operating cost. US DOE has set a target of ≤ 0.25 mgPt/cm 2 total loading in the membrane electrode assembly, high fuel efficiency of > 68% and a HD-combined target of ≥ 2.5 kW/gPGM after running an accelerated stress test (AST) equivalent to 30,000 hours of heavy-duty fuel cell operation.

08 HYDROGEN↗
DOE OSTI2023

Poly(oxymethylene) Ethers as a High Cetane, Low Sooting Biofuel Blendstock for Use in Medium to Heavy Duty Mixing Controlled Compression Ignition Engines

Compression ignition (CI) engines are currently the most common prime mover for medium and heavy duty vehicles; these engines contribute roughly a quarter of US greenhouse gas emissions from transportation, and even higher percentages of particulate and nitrogen oxide emissions. As a result, there have been significant efforts made to reduce these emissions, particularly through selection of low-emissions alternative fuels. Oxymethylene ethers (OMEs) are a class of molecule, typically structured R-O-(CH2O)n-R', which have been considered as a possible blendstock in CI fuels for the goal of soot reduction. Generally, past work has focused on methyl-terminated OMEs, CH3-O-(CH2O)n-CH3, which by virtue of containing no C--C bonds, produce negligible soot. These molecules show significant reductions in soot emission from engines when blended in moderate to high ratios with traditional diesels, however, they have been shown to have inferior physical properties and poor compatibility with some legacy systems. Recent theoretical work has shown that OMEs with non-methyl alkyl groups may have superior performance, albeit at the cost of increased soot formation. In this work, a variety of OMEs with terminating alkyl groups from methyl to butyl are considered for their suitability as CI fuels. The synthesis of these extended OMEs is studied, including formation of n=1 OMEs from common chemical sources, and extension of the chain length to heavier molecules, via reactions over acidic ion exchange resins. Following the synthesis, the properties of these OMEs are studied with respect to their engine applicability. It is found that heavier (propyl- and butyl-terminated) OMEs have superior properties for diesel compatibility, particularly in reactivity, volatility, and water solubility. Extended-alkyl OMEs are found to have higher soot production than methyl-terminated OMEs, but remain superior to diesel soot production on a per-unit-energy basis. A sample of a butyl-terminated OME mixture, n=2-4, is selected as the ideal OME blend for close compatibility with legacy diesel systems. This mixture is blended with certified diesel and tested for ASTM D975 compatibility, passing all required tests but lubricity; decreased heat of combustion is observed but not governed by the diesel standard. Fundamental combustion tests of various mid-weight OMEs are performed in a rapid compression machine, where it is shown that low-temperature chemistry causes a region of decreased dependence of ignition delay on temperature, consistent with methyl-terminated OME behavior. An isopropyl-terminated OME is observed to have low reactivity compared to other OMEs; this fuel is investigated via further rapid compression machine testing and CFR engine testing. It is found that this OME has strong negative-temperature-coefficient ignition behavior - a first for OMEs - and has reactivity lower than other OMEs, but insufficient for direct spark ignition engine testing.

09 BIOMASS FUELS↗