Search NASA⌕ Search

SEARCH · Search NASA

Results for “Dynamic response”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

An Investigation of the Dynamic Response of Spur Gear Teeth with Moving Loads

Two concepts relating to gear dynamics were studied. The first phase of the analysis involved the study of the effect of the speed of a moving load on the dynamic deflections of a gear tooth. A single spur gear tooth modelled using finite elements was subjected to moving loads with variable velocities. The tooth tip deflection time histories were plotted, from which it was seen that the tooth tip deflection consisted of a quasistatic response with an oscillatory response superimposed on it whose amplitude was dependent on the type of load engagement. Including the rim in the analysis added flexibility to the model but did not change the general behavior of the system. The second part of the analysis involved an investigation to determine the effect on the dynamic response of the inertia of the gear tooth. A simplified analysis using meshing cantilever beams was used. In one case, the beams were assumed massless. In the other, the mass (inertia) of the beams was included. From this analysis it was found that the inertia of the tooth did not affect the dynamic response of meshing cantilever beams.

Passerello, C. E.↗
NASA NTRS1986

Dynamic response of two composite prop-fan models on a nacelle/wing/fuselage half model

Results are presented for blade response wind tunnel tests of two 62.2 cm diameter Prop-Fan (advanced turboprop) models with swept and unswept graphite/epoxy composite blades. Measurements of dynamic response were made with the rotors mounted on a simulated nacelle/wing/fuselage model, with varying tilt, at flow speeds up to 0.85 Mach number. The presence of the wing, downstream of the rotor, induced 1-P responses that were about twice those previously measured for an isolated nacelle installation. The swept blade had less 1-P response than the unswept (straight) blade. The 2-P response was significant for both blades, and was closely correlated to wing lift. Higher order response was not important for the straight blade, but possibly important for the swept blade near critical speeds, due to the proximity of the blade tips to the wing leading edge. Measurements are compared with theoretically based prediction. Correlations between calculated and measured 1-P response were good for the straight blade, and fair for the swept blade. Improvements to the calculation method were identified and implemented.

Smith, Arthur F.↗
NASA NTRS1986

Dynamic response and stability of a composite prop-fan model

Results are presented for blade response and stability during wind tunnel tests of a 62.2 cm diameter model of a prop-fan, advanced turboprop, with swept graphite/epoxy composite blades. Measurements of dynamic response were made with the rotor mounted on an isolated nacelle, with varying tilt for nonuniform inflow, at flow speeds from 0.36 to 0.9 Mach number. The blade displayed no instabilities over the operating range tested, up to 0.9 Mach number and 10,000 RPM. Measurements are compared with those for other prop-fan models of both solid metal and graphite composite construction. The swept composite blade had less response than an unswept composite blade. Composite blades had more response than metal blades. Measurements are compared with theoretically based predictions. The 1-P blade response was significantly overpredicted using unimproved methods and somewhat overpredicted using improved methods. Unexpectedly high 2-P strain levels were measured and suggest the presence of nonlinear effects on blade response.

Smith, A. F.↗
NASA NTRS2014

Conceptual Design Optimization of an Augmented Stability Aircraft Incorporating Dynamic Response Performance Constraints

This research focused on incorporating stability and control into a multidisciplinary de- sign optimization on a Boeing 737-class advanced concept called the D8.2b. A new method of evaluating the aircraft handling performance using quantitative evaluation of the sys- tem to disturbances, including perturbations, continuous turbulence, and discrete gusts, is presented. A multidisciplinary design optimization was performed using the D8.2b transport air- craft concept. The con guration was optimized for minimum fuel burn using a design range of 3,000 nautical miles. Optimization cases were run using xed tail volume coecients, static trim constraints, and static trim and dynamic response constraints. A Cessna 182T model was used to test the various dynamic analysis components, ensuring the analysis was behaving as expected. Results of the optimizations show that including stability and con- trol in the design process drastically alters the optimal design, indicating that stability and control should be included in conceptual design to avoid system level penalties later in the design process.

Welstead, Jason↗
NASA NTRS1980

Dynamical response of the dayside ionosphere of Venus to the solar wind

Dayside ion composition measurements made by the orbiter ion mass spectrometer and the orbiter electron temperature probe on the Pioneer Venus orbiter are used to infer the dominant processes involved in the dynamic response of the Venus ionosphere to the solar wind. The analysis is confined to the topside ionosphere in the vicinity of the subsolar point, where the ionosphere-solar wind interaction is expected to be maximized. Height profiles of the ion composition and plasma temperatures in the main body of the topside ionosphere, lying between the ionopause and chemical equilibrium regions, reveal that the ionosphere is in a compressed state. This region of the ionosphere is interpreted in terms of a stationary equilibrium where the compression is derived from the ponderomotive force j x B. The estimated magnitude of this force is confirmed by the magnetic field measurements made by the orbiter magnetometer.

Hartle, R. E.↗
NASA NTRS2000

SMA Hybrid Composites for Dynamic Response Abatement Applications

A recently developed constitutive model and a finite element formulation for predicting the thermomechanical response of Shape Memory Alloy (SMA) hybrid composite (SMAHC) structures is briefly described. Attention is focused on constrained recovery behavior in this study, but the constitutive formulation is also capable of modeling restrained or free recovery. Numerical results are shown for glass/epoxy panel specimens with embedded Nitinol actuators subjected to thermal and acoustic loads. Control of thermal buckling, random response, sonic fatigue, and transmission loss are demonstrated and compared to conventional approaches including addition of conventional composite layers and a constrained layer damping treatment. Embedded SMA actuators are shown to be significantly more effective in dynamic response abatement applications than the conventional approaches and are attractive for combination with other passive and/or active approaches.

Turner, Travis L.↗
NASA NTRS1990

Simulated dynamic response of a servovalve controlled hydraulic actuator

A general purpose math model of a servovalve controlled hydraulic actuator system is derived. The system consists of a linear actuator with unequal piston areas, a single stage servovalve, a gas charged hydraulic accumulator, and the interconnecting piping. The state equations are integrated using the Advanced Continuous Simulation Language (ACSL) for determining the system's dynamic response characteristics. Using this generalized hydraulic actuator system model, response characteristics were determined for various servovalve commands.

Babcock, Dale A.↗
NASA NTRS2018

Dynamical Response of Mediterranean Precipitation to Greenhouse Gases and Aerosols

Atmospheric aerosols and greenhouse gases affect cloud properties, radiative balance and, thus, the hydrological cycle. Observations show that precipitation has decreased in the Mediterranean since the beginning of the 20th century, and many studies have investigated possible mechanisms. So far, however, the effects of aerosol forcing on Mediterranean precipitation remain largely unknown. Here we compare the modeled dynamical response of Mediterranean precipitation to individual forcing agents in a set of global climate models (GCMs). Our analyses show that both greenhouse gases and aerosols can cause drying in the Mediterranean and that precipitation is more sensitive to black carbon (BC) forcing than to well-mixed greenhouse gases (WMGHGs) or sulfate aerosol. In addition to local heating, BC appears to reduce precipitation by causing an enhanced positive sea level pressure (SLP) pattern similar to the North Atlantic Oscillation-Arctic Oscillation, characterized by higher SLP at midlatitudes and lower SLP at high latitudes. WMGHGs cause a similar SLP change, and both are associated with a northward diversion of the jet stream and storm tracks, reducing precipitation in the Mediterranean while increasing precipitation in northern Europe. Though the applied forcings were much larger, if forcings are scaled to those of the historical period of 1901-2010, roughly one-third (31+/-17%) of the precipitation decrease would be attributable to global BC forcing with the remainder largely attributable to WMGHGs, whereas global scattering sulfate aerosols would have negligible impacts. Aerosol-cloud interactions appear to have minimal impacts on Mediterranean precipitation in these models, at least in part because many simulations did not fully include such processes; these merit further study. The findings from this study suggest that future BC and WMGHG emissions may significantly affect regional water resources, agricultural practices, ecosystems and the economy in the Mediterranean region.

Tang, Tao↗
NASA NTRS1978

Improved aircraft dynamic response and fatigue life during ground operations using an active control landing gear system

A three-degree-of-freedom aircraft landing analysis incorporating a series-hydraulic active control main landing gear has been developed and verified using preliminary experimental data from drop tests of a modified main landing gear from a 2722 kg (6000 lbm) class of airplane. The verified analysis was also employed to predict the landing dynamics of a supersonic research airplane with an active control main landing gear system. The results of this investigation have shown that this type of active gear is feasible and indicate a potential for improving airplane dynamic response and reducing structural fatigue damage during ground operations by approximately 90% relative to that incurred with the passive gear.

Mcgehee, J. R.↗
NASA NTRS2014

Dynamic Responses of the Earth's Outer Core to Assimilation of Observed Geomagnetic Secular Variation

Assimilation of surface geomagnetic observations and geodynamo models has advanced very quickly in recent years. However, compared to advanced data assimilation systems in meteorology, geomagnetic data assimilation (GDAS) is still in an early stage. Among many challenges ranging from data to models is the disparity between the short observation records and the long time scales of the core dynamics. To better utilize available observational information, we have made an effort in this study to directly assimilate the Gauss coefficients of both the core field and its secular variation (SV) obtained via global geomagnetic field modeling, aiming at understanding the dynamical responses of the core fluid to these additional observational constraints. Our studies show that the SV assimilation helps significantly to shorten the dynamo model spin-up process. The flow beneath the core-mantle boundary (CMB) responds significantly to the observed field and its SV. The strongest responses occur in the relatively small scale flow (of the degrees L is approx. 30 in spherical harmonic expansions). This part of the flow includes the axisymmetric toroidal flow (of order m = 0) and non-axisymmetric poloidal flow with m (is) greater than 5. These responses can be used to better understand the core flow and, in particular, to improve accuracies of predicting geomagnetic variability in future.

secular variation↗
NASA NTRS1988

Maximum dynamic responses using matched filter theory and random process theory

This paper describes and illustrates two ways of performing time-correlated gust-load calculations. The first is based on Matched Filter Theory; the second on Random Process Theory. The two yield theoretically identical results and both employ novel applications of the theories and unconventional interpretations of the intermediate and final results. Both approaches are computationally fast and are general enough to be applied to dynamic-response problems other than gust loads. A brief mathematical development and example calculations using both Matched Filter Theory and Random Process Theory are presented.

Pototzky, Anthony S.↗
NASA NTRS1979

Dynamic response of damaged angleplied fiber composites

The effects of low level damage induced by monotonic load, cyclic load and/or residual stresses on the vibration frequencies and damping factors of fiber composite angleplied laminates were investigated. Two different composite systems were studied - low modulus fiber and ultra high modulus fiber composites. The results obtained show that the frequencies and damping factors of angleplied laminates made from low modulus fiber composites are sensitive to low level damage while those made from ultra high modulus composites are not. Vibration tests may not be sufficiently sensitive to assess concentrated local damage in angleplied laminates. Dynamic response determined from low-velocity impact coupled with the Fast Fourier Transform and packaged in a minicomputer can be a convenient procedure for assessing low-level damage.

Chamis, C. C.↗
NASA NTRS1979

Dynamic response of damaged angleplied fiber composites

An investigation was conducted to determine the effects of low level damage induced by monotonic load, cyclic load and/or residual stresses on the vibration frequencies and damping factors of fiber composite angleplied laminates. Two different composite systems were studied - low modulus fiber and ultra high modulus fiber composites. The results obtained showed that the frequencies and damping factors of angleplied laminates made from low modulus fiber composites are sensitive to low level damage while those made from ultra high modulus composites are not. Also, vibration tests may not be sufficiently sensitive to assess concentrated local damage in angleplied laminates. And furthermore, dynamic response determined from low-velocity impact coupled with the Fast Fourier Transform and packaged in a minicomputer can be a convenient procedure for assessing low-level damage in fiber composite angleplied laminates.

Chamis, C. C.↗
NASA NTRS1972

The effect of support flexibility and damping on the dynamic response of a single mass flexible rotor in elastic bearings

The dynamic unabalance response and transient motion of the single mass Jeffcott rotor in elastic bearings mounted on damped, flexible supports are discussed. A steady state analysis of the shaft and the bearing housing motion was made by assuming synchronous precession of the system. The conditions under which the support system would act as a dynamic vibration absorber at the rotor critical speed were studied. Plots of the rotor and support amplitudes, phase angles, and forces transmitted were evaluated by the computer and the performance curves were plotted by an automatic plotter unit. Curves are presented on the optimization of the support housing characteristics of attenuate the rotor synchronous unbalance response.

Kirk, R. G.↗
NASA NTRS1995

Sensitivity analysis for the dynamic response of viscoplastic shells of revolution

A computational procedure is presented for evaluating the sensitivity coefficients of the dynamic axisymmetric response of viscoplastic shells of revolution. The analytical formulation is based on Reissner's large deformation shell theory with the effects of transverse shear deformation, rotatory inertia and moments turning around the normal to the middle surface included. The material model is chosen to be isothermal viscoplasticity, and an associated flow rule is used with a von Mises effective stress. A mixed formulation is used with the fundamental unknowns consisting of six stress resultants, three generalized displacements and three velocity components. Spatial discretization is performed using finite elements, with discontinuous stress resultants across element interfaces. The temporal integration is performed by using an explicit central difference scheme (leap-frog method) with an implicit constitutive update. The sensitivity coefficients are evaluated using a direct differentiation approach. Numerical results are presented for a spherical cap subjected to step loading, and a circular plate subjected to impulsive loading. The sensitivity coefficients are generated by evaluating the derivatives of the response quantities with respect to thickness, mass density, Young's modulus, and two of the material parameters characterizing the viscoplastic response. Time histories of the response and sensitivity coefficients are presented, along with spatial distributions of these quantities at selected times.

Kulkarni, Makarand↗
NASA NTRS1996

A dynamic response model for pressure sensors in continuum and high Knudsen number flows with large temperature gradients

This paper develops a dynamic model for pressure sensors in continuum and rarefied flows with longitudinal temperature gradients. The model was developed from the unsteady Navier-Stokes momentum, energy, and continuity equations and was linearized using small perturbations. The energy equation was decoupled from momentum and continuity assuming a polytropic flow process. Rarefied flow conditions were accounted for using a slip flow boundary condition at the tubing wall. The equations were radially averaged and solved assuming gas properties remain constant along a small tubing element. This fundamental solution was used as a building block for arbitrary geometries where fluid properties may also vary longitudinally in the tube. The problem was solved recursively starting at the transducer and working upstream in the tube. Dynamic frequency response tests were performed for continuum flow conditions in the presence of temperature gradients. These tests validated the recursive formulation of the model. Model steady-state behavior was analyzed using the final value theorem. Tests were performed for rarefied flow conditions and compared to the model steady-state response to evaluate the regime of applicability. Model comparisons were excellent for Knudsen numbers up to 0.6. Beyond this point, molecular affects caused model analyses to become inaccurate.

Whitmore, Stephen A.↗
NASA NTRS1995

Dynamic response tests of inertial and optical wind-tunnel model attitude measurement devices

Results are presented for an experimental study of the response of inertial and optical wind-tunnel model attitude measurement systems in a wind-off simulated dynamic environment. This study is part of an ongoing activity at the NASA Langley Research Center to develop high accuracy, advanced model attitude measurement systems that can be used in a dynamic wind-tunnel environment. This activity was prompted by the inertial model attitude sensor response observed during high levels of model vibration which results in a model attitude measurement bias error. Significant bias errors in model attitude measurement were found for the measurement using the inertial device during wind-off dynamic testing of a model system. The amount of bias present during wind-tunnel tests will depend on the amplitudes of the model dynamic response and the modal characteristics of the model system. Correction models are presented that predict the vibration-induced bias errors to a high degree of accuracy for the vibration modes characterized in the simulated dynamic environment. The optical system results were uncorrupted by model vibration in the laboratory setup.

Buehrle, R. D.↗
NASA NTRS1988

Contact force history and dynamic response due to the impact of a soft projectile

A series of ballistic impact tests on several different instrumented targets was performed to characterize the dynamic contact force history resulting from the impact of a compliant projectile. The results show that the variation of contact force history with impact velocity does not follow the trends predicted by classical impact models. An empirical model was therefore developed to describe this behavior. This model was then used in a finite-element analysis to estimate the force history and calculate the resulting dynamic strain response in a transversely impacted composite laminate.

Grady, J. E.↗