Search NASA⌕ Search

SEARCH · Search NASA

Results for “Effective thermal conductivity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Nonintrusive thermal-wave sensor for operando quantification of degradation in commercial batteries

Abstract Monitoring real-world battery degradation is crucial for the widespread application of batteries in different scenarios. However, acquiring quantitative degradation information in operating commercial cells is challenging due to the complex, embedded, and/or qualitative nature of most existing sensing techniques. This process is essentially limited by the type of signals used for detection. Here, we report the use of effective battery thermal conductivity ( k eff ) as a quantitative indicator of battery degradation by leveraging the strong dependence of k eff on battery-structure changes. A measurement scheme based on attachable thermal-wave sensors is developed for non-embedded detection and quantitative assessment. A proof-of-concept study of battery degradation during fast charging demonstrates that the amount of lithium plating and electrolyte consumption associated with the side reactions on the graphite anode and deposited lithium can be quantitatively distinguished using our method. Therefore, this work opens the door to the quantitative evaluation of battery degradation using simple non-embedded thermal-wave sensors.

25 ENERGY STORAGE↗
DOE OSTI2021

Pressure, temperature, and orientation dependent thermal conductivity of pentaerythritol tetranitrate (PETN)

We use reverse non-equilibrium molecular dynamics to determine the thermal conductivity tensor, κ, of tetragonal pentaerythritol tetranitrate (PETN). The most stable form under standard ambient conditions (PETN I, with space group P4¯2 1 c) is considered in the temperature and pressure intervals 200–500 K and 0–8 GPa, which covers approximately the stability range for this polymorph. We compute κ along the [100] and [001] directions, which is enough to construct the full thermal conductivity tensor for a system with tetragonal symmetry. In addition, we also determine κ along the [010] direction and confirm that κ 100 ~ κ 010 , with less than 4% average absolute error between the two quantities. We observe an anisotropic response for κ, with κ 100 > κ 001 across the whole (T,P) interval, and 37% difference at 300 K, 0 GPa. Furthermore, we provide analytical functions to interpolate κ(P,T) within the fitting interval and serve as input for continuum-scale simulations.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Thermomagnetic responses of semimetals

Solid-state thermomagnetic modules operating based on the Nernst–Ettingshausen effects are an alternative to conventional solid-state thermoelectric modules. These modules are appropriate for low-temperature applications where the thermoelectric modules are not efficient. Here, we briefly discuss the application, performance, similarities, and differences of thermoelectric and thermomagnetic materials and modules. We review thermomagnetic module design, Nernst coefficient measurement techniques, and theoretical advances, emphasizing the Nernst effect and factors influencing its response in semimetals such as carrier compensation, Fermi surface, mobility, phonon drag, and Berry curvature. The main objective is to summarize the materials design criteria to achieve high thermomagnetic performance to accelerate thermomagnetic materials discovery.

42 ENGINEERING↗
DOE OSTI2025

Machine learning interatomic potential for predicting the thermal properties of uranium nitride

We present a combined computational and experimental investigation of the thermal properties of uranium nitride (UN), focusing on the development of a machine learning interatomic potential (MLIP) using the moment tensor potential framework. The MLIP was trained on density functional theory (DFT) data and validated against various quantities including energies, forces, elastic constants, phonon dispersion, and defect formation energies, achieving excellent agreement with DFT calculations, prior experimental results, and our thermal conductivity measurement. The potential was then employed in molecular dynamics simulations to predict key thermal properties such as melting point, thermal expansion, specific heat, and lattice thermal conductivity. To further assess model accuracy, we fabricated a UN sample and performed new thermal conductivity measurements representative of single-crystal properties, which showed strong agreement with the MLIP predictions. This work confirms the reliability and predictive capability of the developed potential for determining the thermal properties of UN.

36 - MATERIALS SCIENCE↗
DOE OSTI2025

Loss-of-Coolant Accident Analysis of a High-Burnup Pressurized Water Reactor Core Design Using Gadolinia-Doped UO 2

High-burnup and extended enrichment fuels are of interest for extending the cycle lengths of pressurized water reactors from 18 to 24 months. Changes to the fuel design and core loading scheme have potentially significant safety implications due to power distribution effects, reduced thermal conductivity, and/or increased plenum pressures due to additional burnable poison loadings. Additionally, higher burnups result in increased material degradation and risk of fuel fragmentation, relocation, and dispersal (FFRD). A representative 24-month core design using gadolinia-doped UO 2 was analyzed for performance under large-break (LB) loss-of-coolant accident (LOCA) conditions using PARCS, RELAP5-3D, and BISON. Furthermore, all considered acceptance criteria were met, with no cases exceeding the 1477 K maximum cladding temperature or the post-quench ductility oxidation limit of 17% equivalent cladding reacted. Full-core FFRD susceptibility was estimated to be approximately 455 kg, though high uncertainties exist with current approaches for computing susceptibility. Undoped fuel rods are more likely to be limiting due to higher linear heat rates. Relatively high burnup and linear heat rate rods located in second batch assemblies are of greatest safety significance during LB LOCA for this high-burnup core design.

High burnup↗
DOE OSTI2023

Phonon Hall Viscosity of Ionic Crystals

When time-reversal symmetry is broken, the low-energy description of acoustic lattice dynamics allows for a dissipationless component of the viscosity tensor, the phonon Hall viscosity, which captures how phonon chirality grows with the wave vector. In this work, we show that, in ionic crystals, a phonon Hall viscosity contribution is produced by the Lorentz forces on moving ions. We calculate typical values of the Lorentz force contribution to the Hall viscosity using a simple square lattice toy model, and we compare it with literature estimates of the strengths of other Hall-viscosity mechanisms.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Tailoring Charge Transport and Magnetism in Complex Half-Heusler/Full-Heusler Nanocomposites (Final Report)

This project exploits (1) the facile co-crystallization of the half-Heusler (HH) and full-Heusler (FH) structures, (2) the high coherency and stability of the HH/FH interfaces, and (3) the solid-state inter-conversion between HH and FH structures through local atomic diffusion, to investigate, for selected compositions of the HH and FH phases, the effect of size, dimensionality, dispersion and volume fraction of FH nanostructures on the electronic, phonon and magnetic behavior of the resulting HH/FH nanocomposites. Our goal is to identify and control key material and growth parameters governing phase formation, microstructural evolution, and to understand the mechanism by which these changes of the internal structure modify the material’s performance. To elucidate the mechanism by which the FH nanostructures regulate electronic charge transport and induce ferromagnetism within non-magnetic and magnetic semiconducting HH matrices, suitable series of HH/0D-FH and HH/2D-FH nanocomposites will be fabricated using synthesis conditions suggested by theoretical calculations of the formation energy and stability of various FH phases (varying M) in HH matrices with known chemical composition. The structure of the HH/FH interfaces (size, chemical composition, volume fraction and dispersion) will be investigated along with the evaluation of the electronic (carrier density, mobility, thermopower, electrical conductivity, effective mass), thermal and magnetic (susceptibility, magnetization etc.) properties of the resulting HH/FH nanocomposites.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Critical roles of pores and moisture in sustainable nanocellulose-based super-thermal insulators

In a recent report in Matter, Bergström and co-workers describe a novel thermal transport behavior that subverts this assumption of porous materials. In their work, the authors describe a nanocellulose-based foam that features ultrahigh porosity (> 99.6%) and aligned µm-scale pores (10–100 µm) whose radial thermal conductivity (i.e., perpendicular to the pore alignment) is close to that of free air in the dry state. Furthermore, the radial thermal conductivity of the cellulose-based foam can be reduced to ~14 mW/(m·K) when the relative humidity is ~35%. Super-thermal insulators, which demonstrate a thermal conductivity below that of stationary air (~ 25 mW/(m·K), 20 ºC, 1.0 atm), are needed to minimize heat loss in various applications (e.g., buildings, thermal energy storage tanks, cold chain packaging, etc.) to mitigate the energy crisis and reduce carbon emissions. Introducing pores into a material is a facile and effective way to achieve low thermal conductivity as pores can suppress thermal transport through solids by reducing the cross-sectional area and increasing the tortuosity of the heat transfer pathway. In porous structures there are two kinds of pores: open and closed. While increased porosity can reduce heat conduction through solids with an open porous structure, the improved gas conduction creates a competing effect that simultaneously elevates the heat transfer. Therefore, the thermal conductivity of a material with µm-scale open pores is usually larger than that of stationary air. Reducing the pore size to less than the mean free path of air (~ 70 nm, 20 ºC, 1.0 atm) can effectively reduce gas conduction, enabling the material to achieve a thermal conductivity below that of stationary air. However, high cost of the nanosized raw materials and time-consuming fabrication processes limit the large-scale applications of nanoporous thermal insulators. Meanwhile, closed pores can block heat transport only through the continuous gas phase. As a result, the thermal conductivity of a closed porous structure can theoretically be much smaller than that of stationary air if the solid conduction can also be suppressed by (1) lowering the solid content of the material, (2) reducing the thermal conductivity of the building blocks of the material, and/or (3) increasing interfacial thermal resistance between neighboring building blocks. Most processes used to generate porous structures (e.g., supercritical drying, freeze drying) involve a solvent that escapes the material. Therefore, it is difficult to create pores and isolate them simultaneously, preventing the fabrication of super-thermal insulators with closed pores.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Process-dependent anisotropic thermal conductivity of laser powder bed fusion AlSi10Mg: impact of microstructure and aluminum-silicon interfaces

Purpose AlSi10Mg alloy is commonly used in laser powder bed fusion due to its printability, relatively high thermal conductivity, low density and good mechanical properties. However, the thermal conductivity of as-built materials as a function of processing (energy density, laser power, laser scanning speed, support structure) and build orientation, are not well explored in the literature. This study aims to elucidate the relationship between processing, microstructure, and thermal conductivity. Design/methodology/approach The thermal conductivity of laser powder bed fusion (L-PBF) AlSi10Mg samples are investigated by the flash diffusivity and frequency domain thermoreflectance (FDTR) techniques. Thermal conductivities are linked to the microstructure of L-PBF AlSi10Mg, which changes with processing conditions. The through-plane exceeded the in-plane thermal conductivity for all energy densities. A co-located thermal conductivity map by frequency domain thermoreflectance (FDTR) and crystallographic grain orientation map by electron backscattered diffraction (EBSD) was used to investigate the effect of microstructure on thermal conductivity. Findings The highest through-plane thermal conductivity (136 ± 2 W/m-K) was achieved at 59 J/mm 3 and exceeded the values reported previously. The in-plane thermal conductivity peaked at 117 ± 2 W/m-K at 50 J/mm 3 . The trend of thermal conductivity reducing with energy density at similar porosity was primarily due to the reduced grain size producing more Al-Si interfaces that pose thermal resistance. At these interfaces, thermal energy must convert from electrons in the aluminum to phonons in the silicon. The co-located thermal conductivity and crystallographic grain orientation maps confirmed that larger colonies of columnar grains have higher thermal conductivity compared to smaller columnar grains. Practical implications The thermal properties of AlSi10Mg are crucial to heat transfer applications including additively manufactured heatsinks, cold plates, vapor chambers, heat pipes, enclosures and heat exchangers. Additionally, thermal-based nondestructive testing methods require these properties for applications such as defect detection and simulation of L-PBF processes. Industrial standards for L-PBF processes and components can use the data for thermal applications. Originality/value To the best of the authors’ knowledge, this paper is the first to make coupled thermal conductivity maps that were matched to microstructure for L-PBF AlSi10Mg aluminum alloy. This was achieved by a unique in-house thermal conductivity mapping setup and relating the data to local SEM EBSD maps. This provides the first conclusive proof that larger grain sizes can achieve higher thermal conductivity for this processing method and material system. This study also shows that control of the solidification can result in higher thermal conductivity. It was also the first to find that the build substrate (with or without support) has a large effect on thermal conductivity.

Engineering↗
DOE OSTI2020

Bi-directional tuning of thermal transport in SrCoO x with electrochemically induced phase transitions

Unlike the wide-ranging dynamic control of electrical conductivity, there does not exist an analogous ability to tune thermal conductivity by means of electric potential. The traditional picture assumes that atoms inserted into a material’s lattice act purely as a source of scattering for thermal carriers, which can only reduce thermal conductivity. In contrast, here we show that the electrochemical control of oxygen and proton concentration in an oxide provides a new ability to bi-directionally control thermal conductivity. On electrochemically oxygenating the brownmillerite SrCoO 2.5 to the perovskite SrCoO 3–δ , the thermal conductivity increases by a factor of 2.5, whereas protonating it to form hydrogenated SrCoO 2.5 effectively reduces the thermal conductivity by a factor of four. This bi-directional tuning of thermal conductivity across a nearly 10 ± 4-fold range at room temperature is achieved by using ionic liquid gating to trigger the ‘tri-state’ phase transitions in a single device. We elucidated the effects of these anionic and cationic species, and the resultant changes in lattice constants and lattice symmetry on thermal conductivity by combining chemical and structural information from X-ray absorption spectroscopy with thermoreflectance thermal conductivity measurements and ab initio calculations. This ability to control multiple ion types, multiple phase transitions and electronic conductivity that spans metallic through to insulating behaviour in oxides by electrical means provides a new framework for tuning thermal transport over a wide range.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Effect of Sn oxides on the thermal conductivity of polycrystalline SnSe

SnSe is a promising thermoelectric material, with intrinsically low lattice thermal conductivity, κL. Surprisingly, in several reports, polycrystalline samples are found to have a higher thermal conductivity than single crystals. This disparity has been attributed to trace amounts of thermally conductive Sn oxides at the grain boundaries of polycrystalline samples. The same culprit was recently proposed to explain the reduction of κL in purified, oxide-free, SnSe polycrystals. Here, we test this hypothesis by: (i) tuning the type of oxide in SnSe by exploiting thermodynamic stability regions, since Sn-rich or Sn-poor compositions favour the formation of SnO or SnO 2 , respectively; and (ii) varying the quantity of SnO 2 by intentionally oxidizing SnSe powder before consolidation, to obtain samples with quantifiable amounts - up to 15% - of SnO 2 . We find that the κL of SnSe is impervious to changes in the type or the amount of Sn oxide present in the samples. Our results show that a simple “rule of mixtures” cannot be used to estimate the effect of grain boundary oxides on the thermal conductivity of SnSe. These results call for an improved understanding of the intriguing thermal transport mechanisms in SnSe and numerous other systems where a two-phase transport is presumed.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Thermal conductivity modeling of monodispersed microspheres using discrete element method

Particle beds are widely used in various systems and processes, such as particle heat exchangers, granular flow reactors, and additive manufacturing. Accurate modeling of the thermal conductivity of particle beds and understanding of their heat transfer mechanisms are important. However, previous models were based on simple cubic packing of particles, which could not accurately represent the actual heat transfer processes under certain conditions. Here, we examine the effect of the packing structure on the thermal conductivity of particle beds. We use monodispersed silica microspheres with average particle sizes ranging from 23 to 330 μm as a model material. We employ a transient hot-wire technique to measure the thermal conductivity of the particle beds with packing density of 43%–57% within a temperature range of room temperature to 500 °C and under N2 gaseous pressures of 20–760 Torr. We then use a discrete element method (DEM) to obtain the realistic packing structure of the particles, which is then fed into a finite-element model (FEM) to calculate the thermal conductivity, with the consideration of solid conduction, gas conduction, and radiation heat transfer. Our results show that the thermal conductivity model based on the more realistic random packing structure derived from the DEM shows better agreement with the experimental data compared to that based on the simple cubic-packing structure. The combined DEM and FEM methodology can serve as a useful tool to predict the effective thermal conductivity of particle beds and to quantify different heat transfer mechanisms under various conditions.

14 SOLAR ENERGY↗
DOE OSTI2023

Microscale Imaging of Thermal Conductivity Suppression at Grain Boundaries

Abstract Grain‐boundary engineering is an effective strategy to tune the thermal conductivity of materials, leading to improved performance in thermoelectric, thermal‐barrier coatings, and thermal management applications. Despite the central importance to thermal transport, a clear understanding of how grain boundaries modulate the microscale heat flow is missing, owing to the scarcity of local investigations. Here, thermal imaging of individual grain boundaries is demonstrated in thermoelectric SnTe via spatially resolved frequency‐domain thermoreflectance. Measurements with microscale resolution reveal local suppressions in thermal conductivity at grain boundaries. Also, the grain‐boundary thermal resistance – extracted by employing a Gibbs excess approach – is found to be correlated with the grain‐boundary misorientation angle. Extracting thermal properties, including thermal boundary resistances, from microscale imaging can provide comprehensive understanding of how microstructure affects heat transport, crucially impacting the materials design of high‐performance thermal‐management and energy‐conversion devices.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A survey of the effects of magnetic fields, resistivity, viscosity and thermal conduction on the Rayleigh–Taylor instability

The Rayleigh–Taylor instability (RTI) is ubiquitous in nature and has been investigated in great detail in a number of theoretical, numerical, and experimental studies relevant to laboratory and space plasmas. Here, the RTI can significantly be altered by the presence of magnetic fields, resistivity, viscosity, and thermal conduction. This paper presents a brief survey and summarizes initial findings of the effect of a plasma RTI modified by these effects.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Pore-Confined Polymers Enhance the Thermal Conductivity of Polymer Nanocomposites

In this work, molecularly confined polymer fillers in nanopores were found to give superior mechanical properties of polymer nanocomposites. In this work, we study the thermal conductivity of such nanocomposites and unveil the effect of polymer confinement on thermal conductivity. Using the time-domain thermoreflectance method, we measure the cross-plane thermal conductivity of polymer nanocomposites that consist of polystyrene fillers confined within a nanoporous organosilicate matrix. Compared to unconfined bulk polystyrene fillers, we find that pore-confined polystyrene fillers enhance the thermal conductivity of the polymer nanocomposites. This enhancement is attributed to the better aligned and less entangled chains in the confined phase, where chain–chain phonon scatterings are reduced. Our work provides essential insights into the thermal conductivity of polymer nanocomposites for multifunctional thermal and mechanical applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Impact of dynamic Jahn-Teller effect on magnetic excitations, lattice vibration, and thermal conductivity in U 𝑥 ⁢T⁢h 1−𝑥 ⁡O 2 system

Vibrational and magnetic properties of single-crystal uranium-thorium dioxide (U 𝑥 ⁢T⁢h 1−𝑥⁡ O 2 ) with a full range of 0 < 𝑥 < 1 are investigated. Thorium dioxide is a diamagnet whose thermal properties are governed by lattice vibration. The addition of paramagnetic uranium ions leads to the emergence of magnetic effects that alter the thermophysical properties noticeably even at room temperature. The interaction of phonons with magnetic moments of uranium 5⁢𝑓 electrons mediated by magnetoelastic coupling results in an anomalous low-temperature thermal conductivity profile. Analysis of the magnetic susceptibility measurements indicates a departure from the Curie-Weiss relationship characteristic of noninteracting paramagnetic ions, previously associated with the dynamic Jahn-Teller (DJT) effect characterized by coupling between spin and the oxygen sublattice. The T 2⁢g Raman peak position follows a nonlinear trend as a function of uranium concentration and hints that these Raman active optical modes play a role in either DJT or in mediating quadrupole-quadrupole interactions. A first-principle-based thermal transport model is implemented to explain the low-temperature transport measurements, where the anomalous reduction is attributed to phonon-spin resonant scattering. The interplay between spins and phonons is also captured using high-resolution inelastic x-ray scattering (IXS) measurements of phonon linewidths. Our results provide insights into the phonon interactions with the magnetic excitations governing DJT effect and impacting the low-temperature thermal transport processes in this material system. Furthermore, these findings have implications for understanding low-temperature thermal transport and magnetic properties in advanced materials for information processing and energy applications.

36 - MATERIALS SCIENCE↗
DOE OSTI2026

Coupling Microstructural Evolution Simulations to Material Property Degradation Predictions for Plasma-Facing Materials

Reliable material performance is required for plasma-facing material (PFM) candidates. Previous research has shown that plasma and neutron radiation exposure induces microstructural changes in PFMs; changes in thermal and electrical conductivities and in material hardening and embrittlement were also observed after neutron irradiation. These material property changes will negatively impact the performance of the PFMs in a fusion reactor. Despite the well-known connection between material microstructure, properties, and performance, there is a need for validated modeling capabilities connecting PFM property degradation with microstructural evolution under fusion-relevant conditions. We are developing a simulation capability to couple plasma-induced microstructural evolution to material property degradation. Our approach relies on deliberate mapping between individual simulation models and experimental characterization for validation. The open-source Multiphysics Object-Oriented Simulation Environment (MOOSE) software was used for this simulation capability development. A MOOSE phase-field model was coupled with the cluster dynamics code, Xolotl, to predict microstructural evolution. Microstructure characterization techniques, including scanning electron microscopy (SEM), transmission electron microscopy (TEM), and laser scanning confocal microscopy (LSCM) are used to validate these microstructural evolution simulations. Calculation of thermal and electrical conductivities with first principles simulations was performed for bulk material and for grain boundaries; these results are used within MOOSE models to calculate effective thermal and electrical conductivities as a function of grain characteristics. Thermoreflectance and four-probe techniques were employed to measure the thermal and electrical conductivities, respectively. A MOOSE crystal plasticity model was adapted to predict microstructure-sensitive deformation behavior, and X-ray diffraction (XRD) was used to collect bulk dislocation density data for validation. After individual simulation validation, these models are coupled to predict material property changes resulting from plasma exposure. We focused here on an experimental design to emphasize the separate effects of moderate thermal loads and plasma exposure using tungsten. Annealing of tungsten was performed under a protective environment for temperatures ranging from 500 C to 1500 C. The plasma exposure was completed in the Tritium Plasma Experiment at Idaho National Laboratory under a deuterium flux of 1e22 D/m^2-s. This incremental approach is employed to build confidence in the modeling capability: separate-effects tests ensure that the models capture key mechanisms from single environmental conditions before predicting PFM property degradation under combined loads. We will show our early results from coupling these simulation models to predict PFM property changes from microstructural evolution. Comparisons of the simulation results with preliminary validation data will be discussed.

36 - MATERIALS SCIENCE↗
DOE OSTI2026

Connect microstructure evolution to property degradation with validated simulation

Reliable material performance is required for plasma-facing material (PFM) candidates. Previous research has shown that plasma and neutron radiation exposure induces microstructural changes in PFMs; changes in thermal and electrical conductivities and in material hardening and embrittlement were also observed after neutron irradiation. These material property changes will negatively impact the performance of the PFMs in a fusion reactor. Despite the well-known connection between material microstructure, properties, and performance, there is a need for validated modeling capabilities connecting PFM property degradation with microstructural evolution under fusion-relevant conditions. We are developing a simulation capability to couple plasma-induced microstructural evolution to material property degradation. Our approach relies on deliberate mapping between individual simulation models and experimental characterization for validation. The open-source Multiphysics Object-Oriented Simulation Environment (MOOSE) software was used for this simulation capability development. A MOOSE phase-field model was coupled with the cluster dynamics code, Xolotl, to predict microstructural evolution. Microstructure characterization techniques, including scanning electron microscopy (SEM), transmission electron microscopy (TEM), and laser scanning confocal microscopy (LSCM) are used to validate these microstructural evolution simulations. Calculation of thermal and electrical conductivities with first principles simulations was performed for bulk material and for grain boundaries; these results are used within MOOSE models to calculate effective thermal and electrical conductivities as a function of grain characteristics. Thermoreflectance and four-probe techniques were employed to measure the thermal and electrical conductivities, respectively. A MOOSE crystal plasticity model was adapted to predict microstructure-sensitive deformation behavior, and X-ray diffraction (XRD) was used to collect bulk dislocation density data for validation. After individual simulation validation, these models are coupled to predict material property changes resulting from plasma exposure. We focused here on an experimental design to emphasize the separate effects of moderate thermal loads and plasma exposure using tungsten. Annealing of tungsten was performed under a protective environment for temperatures ranging from 500$^o$C to 1500$^o$C. The plasma exposure was completed in the Tritium Plasma Experiment at Idaho National Laboratory under a deuterium flux of 1e22 $\frac{D}{m^2s}$. This incremental approach is employed to build confidence in the modeling capability: separate-effects tests ensure that the models capture key mechanisms from single environmental conditions before predicting PFM property degradation under combined loads. We will show our early results from coupling these simulation models to predict PFM property changes from microstructural evolution. Comparisons of the simulation results with preliminary validation data will be discussed.

36 - MATERIALS SCIENCE↗