Search NASA⌕ Search

SEARCH · Search NASA

Results for “Electron temperature profile”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

MBE growth and donor doping of coherent ultrawide bandgap AlGaN alloy layers on single-crystal AlN substrates

Single-crystal Aluminum Nitride (AlN) crystals enable the epitaxial growth of ultrawide bandgap Al(Ga)N alloys with drastically lower extended defect densities. Here, we report the plasma-MBE growth conditions for high Al-composition AlGaN alloys on single-crystal AlN substrates. An AlGaN growth guideline map is developed, leading to pseudomorphic Al x Ga 1–x N epitaxial layers with x ~0.6–1.0 Al contents at a growth rate of ~0.3 μm/h. These epitaxial layers exhibit atomic steps, indicating step flow epitaxial growth, and room-temperature band edge emission from ~4.5 to 5.9 eV. Growth conditions are identified in which the background impurity concentrations of O, C, Si, and H in the MBE layers are found to be very near or below detection limits. An interesting Si segregation and gettering behavior is observed at the epitaxial AlGaN/AlN heterojunction with significant implications for the formation and transport of 2D electron or hole gases. Well-controlled intentional Si doping ranging from ~2 × 10 17 to 3 × 10 19 atoms/cm 3 is obtained, with sharp dopant density transition profiles. In Si-doped Al 0.6 Ga 0.4 N epilayers, a room-temperature free electron concentration of ~3 × 10 19 /cm 3 , an electron mobility of ~27 cm 2 /V s, and an n-type resistivity of ~7.5 m Ω cm are obtained. Here, the implications of these findings on electronic and photonic devices on single-crystal AlN substrates are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Identity of the JET M-mode and the ASDEX Upgrade I-phase phenomena

An H-mode plasma state free of edge-localized mode (ELM), close to the L-H transition with clear density and temperature pedestal has been observed both at the Joint European Torus (JET) and at the ASDEX Upgrade (AUG) tokamaks usually identified by a low frequency (LFO, 1–2 kHz), m = 1, n = 0 oscillation of the magnetics and the modulation of pedestal profiles. The regime at JET is referred to as M-mode while at AUG as intermediate phase or I-phase. This contribution aims at a comparative analysis of these phenomena in terms of the density and temperature pedestal properties, the magnetic oscillations and symmetries. Lithium beam emission spectroscopy (Li-BES) and reflectometer measurements at JET and AUG show that the M-mode and the I-phase modulates the plasma edge density. A high frequency oscillation of the magnetics and the density at the pedestal is also associated with both the M-mode and the I-phase, and its power is modulated with the LFO frequency. The power modulation happens simultaneously in every Mirnov coil signal where it can be detected. The bursts of the magnetic signals and the density at the pedestal region are followed by the flattening of the density profile, and by a radially outward propagating density pulse in the scrape-off layer (SOL). The analysis of the helium line ratio spectroscopy (He-BES) signals at AUG revealed that the electron temperature is modulated in phase with the density, thus the I-phase modulates the pressure profile gradient. Overall, this analysis gave opportunity to compare Li-BES and He-BES density profiles at different locations suggesting a toroidal and poloidal symmetry of the density modulation. The presented results indicate that the regimes, the AUG I-phase and the JET M-mode, exhibit similar characteristics, which leads to the conclusion that the regimes are likely the same.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Neural-Network-Enhanced COTSIM: Advancing Predictive Capabilities for Fast DIII-D Simulations

Sustaining fusion reactions in tokamaks requires heating plasma to thermonuclear temperatures while maintaining confinement and stability. Neutral beam injection (NBI) provides heating, current drive, torque, and fueling, while electron cyclotron (EC) waves are widely used for heating and current drive; together, these actuators shape the plasma current, temperature, and density profiles. The control-oriented tokamak simulator (COTSIM), a predictive, control-oriented code, has been enhanced with neural-network surrogates for transport and sources. Turbulent transport is predicted by MMMnet—a neural-network version of the updated multimode model (MMM 9.0.10)—with significantly reduced computation time relative to MMM; neoclassical transport follows the Chang–Hinton model. NUBEAMnet, a surrogate of the Monte Carlo NUBEAM module, predicts beam-driven heating, current, and torque. EC heating and current drive use a control-oriented, empirically scaled source model; plasma resistivity follows the Spitzer formulation; bootstrap current uses the Sauter model. Equilibrium is computed using both prescribed and fixed-boundary solvers (FBSs), and the pedestal structure is modeled with an empirical pedestal model. For a representative DIII-D discharge, COTSIM predicts electron and ion temperature and safety-factor profiles in close agreement with TRANSP predictive and interpretive simulations while extending predictions through the pedestal region to the plasma edge (versus 80% of the minor radius in TRANSP). Furthermore, the equivalent COTSIM simulation runs in under 3 min compared to about 2 h for TRANSP, enabling rapid scenario planning, optimization of tokamak operation, and between-pulse control design.

Control-oriented tokamak simulator (COTSIM)↗
DOE OSTI2025

Electron cyclotron emission measurements and modeling in optically semi-transparent plasma on the HSX stellarator

On the Helically Symmetric Experiment (HSX), electron cyclotron emission (ECE) at the second harmonic of the electron gyrofrequency is measured with a 16-channel heterodyne receiver. An ECE radiometer diagnostic has been calibrated with a broadband frequency source, allowing independent measurements of the electron temperature. The antenna pattern has a significant impact on the measurements, and modeling its effect is necessary to produce an ECE radiation temperature spectrum. Measurements, calibration results, and modeling of the ECE data are presented in this paper. At a relatively high plasma density, HSX plasmas are thermal, and the radiation temperature measured by the radiometer is in good agreement with the electron temperature measured by a Thomson scattering diagnostic. At a relatively low plasma density, the deviation from a Maxwellian distribution is large, and asymmetry in the radiation temperature profile is measured. These measurements are supported by single-pass and multi-pass ray tracing calculations of the electron cyclotron emission using the TRAVIS ray tracing code. Thermal and nonthermal electron populations exist in HSX, and the effect of these populations on the asymmetry in the measured emission is presented.

Cyclotron radiation↗
DOE OSTI2021

Investigating profile stiffness and critical gradients in shaped TCV discharges using local gyrokinetic simulations of turbulent transport

The experimental observation made on the TCV tokamak of a significant confinement improvement in plasmas with negative triangularity ( δ < 0) compared to those with standard positive triangularity has been interpreted in terms of different degrees of profile stiffness (Sauter et al. Phys. Plasmas 21 055906, 2014) and/or different critical gradients. Employing the Eulerian gyrokinetic code GENE (Jenko et al. Phys. Plasmas 7 1904, 2000), profile stiffness and critical gradients are studied under TCV relevant conditions. For the considered experimental discharges, trapped electron modes (TEMs) and electron temperature gradient (ETG) modes are the dominant microinstabilities, with the latter providing a significant contribution to the non-linear electron heat fluxes near the plasma edge. Two series of simulations with different levels of realism are performed, addressing the question of profile stiffness at various radial locations. Retaining finite collisionality, impurities and electromagnetic effects, as well as the physical electron-to-ion mass ratio are all necessary in order to approach the experimental flux measurements. However, flux-tube simulations are unable to fully reproduce the TCV results, pointing towards the need to carry out radially nonlocal (global) simulations, i.e. retaining finite machine size effects, in a future study. Some conclusions about the effect of triangularity can nevertheless be drawn based on the flux-tube results. In particular, the importance of considering the sensitivity to both temperature and density gradient is shown. The flux tube results show an increase of the critical gradients towards the edge, further enhanced when δ < 0, and they also appear to indicate a reduction of profile stiffness towards plasma edge.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Movable Thermometer System in ProtoDUNE

The movable temperature profiler is a 7 m vertical array of 24 sensors that measures cryogenic temperatures with a precision of a few mK. This precision is necessary to monitor the efficiency of re-circulation and purification of liquid-argon inside large liquid-argon based neutrino detectors. Liquid argon temperature impacts electron (signal) drift velocity, flow, purity distribution and thus the overall energy calibration. The temperature profiler is motorized and moves vertically, while in the detector, and cross-calibrates neighboring sensors. The temperature offsets between each sensor cancel the effects of electromagnetic noise. This poster reports on the temperature measurements and such in-situ cross-calibrations at ProtoDUNE (single phase) at CERN.}

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2024

Inter-ELM pedestal turbulence dynamics dependence on q 95 and temperature gradient

A series of dedicated experiments from DIII-D tokamak provide spatially and temporally resolved measurements of electron density and temperature, and multiscale and multichannel fluctuations over a wide range of conditions. Measurements of long wavelength density fluctuations in the type-I ELMing H-mode pedestal routinely revealed a coexistence of multiple instabilities that exhibit dramatic different dynamic behaviors as q 95 and temperature gradient are varied, apparently responsible for limiting pedestal temperature profiles. Two distinct frequency bands of density fluctuations are modulated with ELM cycle with frequency above 200kHz propagating in the electron diamagnetic direction in the lab frame (electron mode) and below 200kHz propagating in the ion diamagnetic direction (ion mode). The electron mode amplitude peaks near the electron temperature gradient region and increases with q 95 which seems to be correlated with the increased χ e at higher q 95 , similar to the characteristics expected for Micro-tearing Mode (MTM). At higher q 95 , during the inter-ELM period, the ion mode decays at later phase of the ELM cycle. Consistently, the poloidal correlation length of the ion mode is also found to reduce which suggests the possible E×B flow shear suppression of ion mode at later phase of the ELM cycle as the Er well recovers. In contrast, the electron mode grows during the ELM cycle and reaches saturation at around 50-60% of ELM period. Linear gyrokinetic simulations find the MTMs as the most unstable mode in the pedestal electron temperature gradient region. The higher q 95 and lower magnetic shear destabilize MTMs. These observations provide key insights of the underlying physics of multifield properties and rich dataset of experimental 'fingerprints' that enable new tests of the theoretical pedestal models and lead to developing a predictive model for pedestal formation on ITER and future burning plasma experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Micro-tearing mode dominated electron heat transport in DIII-D H-mode pedestal

Abstract A new, comprehensive set of evidence reveals that Micro-Tearing Modes (MTMs) dominate pedestal electron heat transport in an H-mode experiment in the DIII-D tokamak. The experiment investigates the role of MTMs by scanning pedestal collisionality, a main drive of MTM instability, from 0.43 to 0.84 on the pedestal top. Broadband (150–800 kHz) magnetic and density fluctuations originating from the pedestal gradient region and highly consistent with MTMs are observed, with amplitude increasing during the scan. The higher magnetic fluctuation amplitude correlates with a lower pedestal electron temperature gradient, implying MTMs may regulate the pedestal electron heat transport. The collisionality scan results in profile and transport changes consistent with predicted transport capability of MTMs: (1) experimentally-determined electron heat diffusivity increases ∼40% at the location where the broadband density fluctuations peak; (2) ion heat diffusivity has less increase (<20%); and (3) a locally flattened region in the electron temperature pedestal is observed at high collisionality. A local, linear gyrokinetic simulation finds MTMs as the most unstable mode in the pedestal gradient region. In addition, local, nonlinear simulations suggest MTMs can dominate and drive experimentally-relevant, megawatt-level electron heat flux. This result establishes MTMs as an effective transport mechanism in the H-mode pedestal, in particular at high collisionality.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Observation of laser ablation of silicon as a function of pulse length at constant fluence via time-resolved x-ray spectroscopy

We investigate the ablation of silicon as a function of laser pulse length at a constant fluence using time-resolved x-ray spectroscopy data obtained from OMEGA EP experiments at the University of Rochester's Laboratory for Laser Energetics. Our targets consisted of three-layer planar structures composed of Si (50 μm), Cu (25 μm), and SiO 2 (500 μm) layers. The Si layer was irradiated by a 351-nm laser with varying pulse widths of 250 ps, 500 ps, 1 ns, and 10 ns while maintaining a constant fluence of ~27.9 kJ/cm 2 . Electron temperatures and densities of the ablated plasma were determined by analyzing the time-resolved x-ray spectroscopy data through a comparison of experimental measurements with synthetic results obtained from Si atomic calculations in a steady state and non-local thermodynamic equilibrium. These calculations were computed using PrismSPECT. Additionally, radiation-hydrodynamics simulations with FLASH are used to generate simulated plasma-density and plasma-temperature profiles, which are then compared with the experimental measurements. Our analyses reveal that increasing the laser pulse length at a constant fluence results in a decrease in electron temperatures and densities. Furthermore, the longer pulses with lower intensities lead to deeper ablation regions before reaching the peak ablation but lower ionization balances in the silicon layer. Furthermore, these findings emphasize the critical role of laser pulse length in plasma ablation and shock generation for laser-impulse studies.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Investigation of radiated-power for low aspect ratio fusion plasmas

Investigating radiated power in fusion plasmas is of utmost importance to understand the effect of undesired impurities, such as metals, in present devices, or also desired impurities, such as noble gasses, to purposefully radiate a large fraction of power in future devices. These studies are especially important for high Z impurities which will play a crucial role in future generation fusion pilot plants. In this work, we have developed a power radiation analysis module, which is used to investigate 2D distributions of impurity densities and radiated power asymmetries caused due to both plasma rotation and the cooling rate dependence on temperature profile for the cases of experimental NSTX plasmas and designed scenarios for the spherical tokamak advanced reactor (STAR), both being low aspect ratio tokamaks. Two different atomic databases have been tested during this work to study their impact on the radiated power distribution, especially for high Z impurities. Also in PRAM, self-consistent calculations of two-dimensional electron, main ion, and impurity ion densities are carried out using one-dimensional input density, temperature, and rotation profiles. In the case of NSTX, discharges with high rotation of ∼ 170 km s, measured with charge exchange recombination spectroscopy, have been investigated. Rotation-induced charge separation, leading to an electrostatic potential, is calculated iteratively to a self-consistent solution while testing high Z impurities to observe any 2D asymmetry in the core radiated power due to centrifugal forces. The STAR design, being much larger (R = 4 m), is projected to have a much lower rotation, and is shown to have low rotation-induced asymmetries, on the order of ten percent or less, between the low field and high field sides. However, another effect not due to rotation but to the dependence of impurity cooling rates on temperature can lead to radiation peaking off-axis, near the plasma edge. This effect is noticeable for argon in NSTX, for example, but can also be enhanced for certain impurities at much higher temperatures projected for STAR (T e0 ~ 32 keV), for example for undesired tungsten or possibly desired xenon.

NSTX↗
DOE OSTI2023

Probing local electron temperature and density inside a sheared flow stabilized Z-pinch using portable optical Thomson scattering

We report the first optical Thomson scattering measurements inside a high electron temperature (≳1 keV) and moderate electron density (mid 10 16 cm –3 ) plasma. This diagnostic has been built to provide critical plasma parameters, such as electron temperature and density, for Advanced Research Projects Agency-Energy-supported fusion-energy concepts. It uses an 8 J laser at 532 nm in 1.5 ns to measure the high frequency feature of the Thomson scattering profile at 17 locations along the probe axis. It is able to measure electron density from 5 × 10 17 cm –3 to several 10 19 cm –3 and electron temperatures from tens of eV to several keV. Here, in this paper, we describe the design, deployment, and analysis on the sheared flow stabilized Z-pinch machine at Zap Energy named FuZE. The probe beam is aimed at an axial distance of 20 cm from the central electrode and is timed within the temporal envelope of neutron emission. The high temperature and moderate density plasmas generated on FuZE lie in an unconventional regime for Thomson scattering as they are between tokamaks and laser-produced plasmas. We described the analysis considerations in this regime, show that the electron density was below 5 × 10 16 cm –3 at all times during these measurements, and present a sample shot where the inferred electron temperature varied from 167 ± 16 eV to 700 ± 85 eV over 1.6 cm.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

The influence of temperature history and flow mixing on the vapor-phase speciation of uranium oxide nanoparticles

The transport of radioactive material following a nuclear event depends heavily on fallout characteristics (e.g., composition, shape, and size), which in turn are controlled by the conditions under which the fallout forms. To this end, we use a novel plasma flow reactor (PFR) to explore how conditions including temperature history and gas mixing influence the chemical speciation and physical characteristics of uranium oxide nanoparticles. The PFR consists of a glass tube attached to an inductively coupled plasma (ICP) torch via an adaptor piece (ring flow injector) located downstream of the plasma-generating RF coil. We increase the gas flow rates from normal ICP operating conditions to higher values both upstream at the RF coil and downstream at the ring flow injector to create four distinct temperature profiles and two distinct gas flow mixing conditions (normal and higher Ar atomic ratios). Ex situ transmission electron microscopy (TEM) analysis is used to determine the crystal structure, morphology, and size distribution of the synthesized particles as a function of temperature and mixing. The particles display a striking dependence on these conditions in terms of the resulting speciation of uranium oxide: lower temperature (higher upstream) and slower cooling (normal downstream with normal Ar atomic ratio mixing) favor the formation of α-UO 3 particles, while faster cooling (higher downstream with higher Ar atomic ratio mixing) and higher temperature (normal upstream) favor the formation of UO 2 particles. The extent of gas mixing dictates particle aggregation: better mixing encourages the particles to aggregate more extensively. Here these results demonstrate the sensitivity of uranium to initial local conditions and can be used to improve our understanding of the kinetics that drive uranium speciation and ultimately inform fallout transport models.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Microstructure, Texture, and Strength Development during High-Pressure Torsion of CrMnFeCoNi High-Entropy Alloy

The equiatomic face-centered cubic high-entropy alloy CrMnFeCoNi was severely deformed at room and liquid nitrogen temperature by high-pressure torsion up to shear strains of about 170. Its microstructure was analyzed by X-ray line profile analysis and transmission electron microscopy and its texture by X-ray microdiffraction. Microhardness measurements, after severe plastic deformation, were done at room temperature. It is shown that at a shear strain of about 20, a steady state grain size of 24 nm, and a dislocation density of the order of 1016 m−2 is reached. The dislocations are mainly screw-type with low dipole character. Mechanical twinning at room temperature is replaced by a martensitic phase transformation at 77 K. The texture developed at room temperature is typical for sheared face-centered cubic nanocrystalline metals, but it is extremely weak and becomes almost random after high-pressure torsion at 77 K. The strength of the nanocrystalline material produced by high-pressure torsion at 77 K is lower than that produced at room temperature. The results are discussed in terms of different mechanisms of deformation, including dislocation generation and propagation, twinning, grain boundary sliding, and phase transformation.

36 MATERIALS SCIENCE↗
DOE OSTI2025

First result of boronization assisted by the ICWC on EAST with full metal wall

Boron (B), a low-Z (atomic number) material, has been widely utilized in wall conditioning to improve plasma performance in fusion devices. In 2023, boronization was successfully conducted on EAST featuring an ITER-like tungsten divertor and fully metallic first wall. The process employed predischarge coating with carborane (C 2 B 10 H 12 ) as the working material, assisted by ion cyclotron wall conditioning (ICWC). After one time 12 g boronization, it was found the thickness of B film was approximately 120 nm. Post-boronization observations indicated that substantial hydrogen (H) release during initial plasma discharges compared with the consumed W/B wall, attributed to H co-deposition during the ICWC-boronization processing, which led to uncontrollable divertor neutral pressure and plasma density. The H/(H + D) ratio demonstrated a gradual reduction from ∼85% to 30% over more than 1850 s of deuterium plasma, with a cumulative injected energy of 2325 MJ. The B coating significantly enhanced the stored energy in plasma and improved confinement performance. The stored energy in plasma showed an increase of about 20%, primarily due to a reduction in impurity radiation, including oxygen (O) and heavy impurities such as tungsten (W), iron (Fe), and copper (Cu). The effective ion charge (Z eff ) decreased from 2.3 to 2.0. Following ICWC-boronization, the line-integrated radiation profile decreased by nearly 35% in the plasma core, plasma density and electron temperature exhibited an increase of ∼7% and 12% due to enhanced wall fueling and reduced impurity radiation. The lifetime of boronization, as evaluated by the line emissions from boron and other impurity radiation, was about 1700 s of deuterium plasma, with a cumulative injected energy of 2125 MJ on EAST. These findings provide significant insights for evaluating ICWC-boronization applicability in ITER with full W wall structure.

EAST↗
DOE OSTI2025

Challenges and approaches to interpretive modeling of boundary plasma and neutral transport in a closed, pumped divertor

An experimental discharge from the DIII-D tokamak is modeled using the SOLPS-ITER code suite and compared against measurements in the pumped and relatively closed upper divertor. Uncertainties of boundary plasma simulations are identified by attempting to match code inputs to experimental conditions, including iteratively solving transport coefficients to match upstream experimental profiles using varying quantities of core particle flux, different pumping models, and various assumptions of ion thermal transport. Simulated boundary conditions for particle injection at the core interface are shown to be relevant to the plasma solution at the divertor targets, even if upstream transport is modified so that plasma profiles are comparatively similar, although seperatrix density is not held constant. When upstream plasma profiles are matched to experimental measurements by varying diffusive transport coefficients, using either poloidally symmetric or ballooning structure, the model finds a majority of injected energy being transported radially off the computational domain, in conflict with experimental radiated power measurements and heat flux measurements at the divertor target. Imposing a maximum thermal diffusivity or radially shifting the experimental separatrix location of the fitted profiles to increase power conducted to the targets by increasing the upstream electron temperature does not significantly modify this result. Including a thermalizing plenum volume in the simulation domain is shown to maintain the experimental volumetric pumping rate without knowing the neutral energy distribution incident on the pump duct a priori. By modifying transport parameters to match different assumptions for ion temperature, downstream neutral pressure changes by more than a factor of two, suggesting that attention to ion thermal transport may be a critical parameter for simulations to accurately resolve recycling and neutral transport, particularly in a closed divertor geometry. In addition to quantifying various modeling uncertainties, this work motivates both further experimental study and modeling improvements to improve predictive capabilities.

divertor↗
DOE OSTI2022

Equilibrium reconstruction of DIII-D plasmas using predictive modeling of the pressure profile

New workflows have been developed for predictive modeling of magnetohydrodynamic (MHD) equilibrium in tokamak plasmas. The goal of this work is to predict the MHD equilibrium in tokamak discharges without having measurements of the kinetic profiles. The workflows include a cold start tool, which constructs all the profiles and power flows needed by transport codes; a Grad–Shafranov equilibrium solver; and various codes for the sources and sinks. For validation purposes, a database of DIII-D tokamak discharges has been constructed that is comprised of scans in the plasma current, toroidal magnetic field, and triangularity. Initial efforts focused on developing a workflow utilizing an empirically derived pressure model tuned to DIII-D discharges with monotonic safety factor profiles. This workflow shows good agreement with experimental kinetic equilibrium calculations, but is limited in that it is a single fluid (equal ion and electron temperatures) model and lacks H-mode pedestal predictions. The best agreement with the H-mode database is obtained using a theory-based workflow utilizing pressure profile predictions from a coupled TGLF turbulent transport and EPED pedestal models together with external magnetics and Motional Stark Effect (MSE) data to construct the equilibrium. Here, we obtain an average root mean square error of 5.1% in the safety factor profile when comparing the predicted and experimental kinetic equilibrium. We also find good agreement with the plasma stored energy, internal inductance, and pressure profiles. Including MSE data in the theory-based workflow results in noticeably improved agreement with the q-profiles in high triangularity discharges in comparison with the results obtained with magnetic data only. The predictive equilibrium workflow is expected to have wide applications in experimental planning, between-shot analysis, and reactor studies.

Kinsey, J. E. (ORCID:0000000193347473)↗
DOE OSTI2025

Impact of dynamic Jahn-Teller effect on magnetic excitations, lattice vibration, and thermal conductivity in U 𝑥 ⁢T⁢h 1−𝑥 ⁡O 2 system

Vibrational and magnetic properties of single-crystal uranium-thorium dioxide (U 𝑥 ⁢T⁢h 1−𝑥⁡ O 2 ) with a full range of 0 < 𝑥 < 1 are investigated. Thorium dioxide is a diamagnet whose thermal properties are governed by lattice vibration. The addition of paramagnetic uranium ions leads to the emergence of magnetic effects that alter the thermophysical properties noticeably even at room temperature. The interaction of phonons with magnetic moments of uranium 5⁢𝑓 electrons mediated by magnetoelastic coupling results in an anomalous low-temperature thermal conductivity profile. Analysis of the magnetic susceptibility measurements indicates a departure from the Curie-Weiss relationship characteristic of noninteracting paramagnetic ions, previously associated with the dynamic Jahn-Teller (DJT) effect characterized by coupling between spin and the oxygen sublattice. The T 2⁢g Raman peak position follows a nonlinear trend as a function of uranium concentration and hints that these Raman active optical modes play a role in either DJT or in mediating quadrupole-quadrupole interactions. A first-principle-based thermal transport model is implemented to explain the low-temperature transport measurements, where the anomalous reduction is attributed to phonon-spin resonant scattering. The interplay between spins and phonons is also captured using high-resolution inelastic x-ray scattering (IXS) measurements of phonon linewidths. Our results provide insights into the phonon interactions with the magnetic excitations governing DJT effect and impacting the low-temperature thermal transport processes in this material system. Furthermore, these findings have implications for understanding low-temperature thermal transport and magnetic properties in advanced materials for information processing and energy applications.

36 - MATERIALS SCIENCE↗
DOE OSTI2022

Initial Results from Boron Powder Injection Experiments in WEST Lower Single Null L-mode Plasmas

Using a recently installed impurity powder dropper (IPD), boron powder (< 150 μm) was injected into lower single null (LSN) L-mode discharges in WEST. IPDs possibly enable real-time wall conditioning of the plasma-facing components and may help to facilitate H-mode access in the full-tungsten environment of WEST. The discharges in this experiment featured Ip = 0.5 MA, BT = 3.7 T, q95 = 4.3, tpulse = 12–30 s, ne,0 ~ 4×1019 m-2, and PLHCD ~ 4.5 MW. Estimates of the deuterium and impurity particle fluxes, derived from a combination of visible spectroscopy measurements and their corresponding S/XB coefficients, showed decreases of ~ 50% in O+, N+, and C+ populations during powder injection and a moderate reduction of these low-Z impurities (~ 50%) and W (~ 10%) in the discharges that followed powder injection. Along with the improved wall conditions, WEST discharges with B powder injection observed improved confinement, as the stored energy WMHD, neutron rate, and electron temperature Te increased significantly (10–25% for WMHD and 60–200% for the neutron rate) at constant input power. These increases in confinement scale up with the powder drop rate and are likely due to the suppression of ion temperature gradient (ITG) turbulence from changes in Zeff and/or modifications to the electron density profile.

Boronization↗